Search Documents

By I. R. Kramer

The delay time for single crystals of iron, zinc, and pre-strained aluminum was measured under conditions of high-speed deformation. The delay time of aluminum was found to be affected by the orientation of the crystal. Under the dynamic conditions employed, tile calculated "activated volume" term appears to be very small for the three metals studied. IN a previous paper,1 it was shown that under dynamic testing conditions at 78° K, there was a delayed yield in single crystals of aluminum and copper which had been cold-worked prior to testing. The experimental results also indicated that the delay-time effect was not due to the interaction of dislocations with impurity atoms or vacancies, but rather to a dislocation-dislocation interaction since aluminum which has not been prestrained shows no delay-time phenomenon. In this paper, some data are reported on the effects of orientation on the delay time of aluminum single crystals; the delay time of zinc single crystals saturated with nitrogen and the delay time of iron single crystals also were measured. EXPERIMENTAL PROCEDURE Aluminum (99.997 pct) and zinc (99.999 pct) crystals, 1/2 in. in diam and 8 in. long were grown by the Bridgman technique. The iron single crystal was supplied by Dr. R. Maddin. The zinc crystals containing nitrogen were prepared by melting high-purity zinc in a graphite crucible and the nitrogen was introduced by additions of ammonium chloride. The liquid zinc was then drawn up into glass tubes of 1/2 in. diam and allowed to solidify. The rods were cooled to room temperature before the transfer to the mold for conversion into single crystals. The orientation of all specimens was determined by the Laue' back-reflection technique, Fig. 2 and Table I. To prepare for the delay-time measurements, the crystals were cut with a fine jewelers saw and the ends carefully machined. The specimens then were electrolytic ally polished to remove the cold-worked metal, mounted in a special fixture and hand-lapped. As a final step, the crystals were annealed in evacuated tubes. Specimens of aluminum crystals, Nos. 24 and 26, were compressed 0.5 and 2 pct, respectively, in the direction of the later impact. The zinc specimens were aged at 50°C for 15 min, In the case of iron, only two specimens could be obtained. To obtain sufficient data, it was necessary to resort to a reaging treatment. After each delay-time test, the specimens were aged at 65° C for 100 min. This treatment, according to Clark,2 is sufficient to restore the original delay time. It is believed that although the specimens were plastically deformed approximately 10-4 pct, after each test the delay-time values are reliable. The delay-time measurements were made in an apparatus similar to that described previously.' Single crystals approximately 1 in. long and having a diameter of 1/2 in. were placed in a pendulum which consisted of a bar 1/2 in. in diam and 8 ft long, designed with a crystal holder to accommodate the specimen at low temperatures. The crystal was held at a position 2 ft from the front part of the pendulum. This portion of the apparatus was supported on a fine molybdenum wire. A projectile bar of the same diameter and length comprised the other portion of the apparatus. This bar was supported on

Jan 1, 1962

By George M. Fowler

MINING geology is a progressive study, so we must look to the future for the solution of many of its most significant problems. These problems, world-wide in scope, offer ample opportunity for the exercise of the utmost skill and intelligence by all that attempt to solve theta, as it is generally recognized that many ore deposits of the future will he found only by months or years of combined intelligent effort by the several engineering groups. Renewed appraisals are continually being made to better understand the relationship of physical-chemical processes to ore deposition and other mineralization and to interpret the findings of the geophysicists and others in terms of economic results. A study of current geologic activi¬ties clearly reflects the growing tendency for cooperation between the different branches of geology in order to appraise their united efforts. In line with these activities arrangements have been made to transfer the geophysical section of the U. S. Bureau of Mines to the Geological Survey.

Jan 1, 1936

By R. W. Kewish

The preparation of massive uranium metal containing very low concentrations of a number of light elements by bomb reduction of UF4, with calcium is described. Details of procedures are given for preparing high-purity ingredients for the bomb reduction. The as-reduced uranium metal contained, on the average, less than the following amounts of light element impurities, in ppm: Li, 0.1; Be, 0.1; B, 0.1; C, 25; 0, 70; Na, 1; Mg, 3; Al, 2; and Si, 7. Other impurities for which the metal was examined averaged, in ppm: Ca, < 10; V, < 10; Cr, 2; Mn, 6; Fe, 50; Co, < 5; Ni, 8; and Cu, 1. THE preparation of very high-purity uranium metal in massive form for research purposes is of great importance. Recently the kilogram-scale preparation of uranium metal containing less than 70 ppm of detected impurities was accomplished by Blumen-thal and coworkers by vacuum remelting of high-purity crystals of uranium obtained by fused salt electrolysis.1"3 Albert and coworkers4 have reported successful experiments in lowering the concentrations of certain impurity elements in uranium, notably iron, to a few ppm by the zone-melting method. The present paper describes the preparation of high-purity massive uranium metal by the bomb reduction of UF4, with calcium. Early in 1951 a program was undertaken at the Los Alamos Scientific Laboratory to prepare uranium metal of very high purity with respect to a number of the light elements. The methods considered for this purpose were 1) bomb reduction of a uranium halide with calcium, 2) electrolysis of fused salts, and 3) hot wire decomposition of UI4, The first of these processes had been used extensively at Los Alamos since 1943 (and still is used) for the production of uranium metal.5 In considering the three processes it was evident that either of the last two would require an extensive development program with no certainty of success. On the other hand, a study of available data showed that uranium metal of very high purity with respect to some light elements had occasionally been made in routine processing by the first method. It was therefore decided that an intensive study of the bomb-reduction process would be made to see if it could be improved to yield uranium metal with very low concentrations of light elements. DEVELOPMENT OF PROCEDURES The bomb-reduction process used at Los Alamos consists of reducing UF4 with calcium, using iodine as a booster. The reaction is carried out in a magnesium-oxide crucible enclosed in a steel bomb. Argon is used in the bomb to avoid objectionable side reactions which would occur in the presence of air. All ingredients for this bomb-reduction process were examined as possible sources of light elements. It was known that high-purity UF4 was required. The calcium used in the reductions was a source of carbon and magnesium. The magnesium-oxide crucibles were sources of boron, silicon, and magnesium. The iodine did not appear to be a source of any impurities. Pure UF4- The UF4 for bomb reduction is prepared from U3O3 , by successive reduction to UO2, with hydrogen and hydrofluorination of the UO2, with anhydrous HF. Since it was known that no impurities were normally introduced during the gas-solid reactions, effort was directed toward the preparation of high-purity U3O3. Of the many possible procedures for the purification of uranium solutions the following were investigated: 1) Precipitation of uranium peroxide. (Two procedures were tried. The first consisted of simultaneously adding hydrogen-peroxide and ammonium-hydroxide solutions to a uranyl-nitrate solution, containing citric and malonic acids, at such relative rates that precipitation was carried out at a constant pH of 1.5 The second consisted of simultaneously adding uranyl-nitrate, ammonium-hydroxide, and hydrogen-peroxide solutions to an aqueous solution

Jan 1, 1960

By R. P. Marshall

This note describes positive evidence that hydrogen in titanium alloys diffuses under the influence of a thermal gradient. The experiments confirmed the expected similarity of this system to the H-Zr system and produced qualitative information on the magnitude of the heat of transport for hydrogen in titanium alloys. This effect has practical importance in applications where titanium alloys operate in a thermal gradient under conditions such that hydrogen embrittlement may develop within the expected lifetime of the structure, for example in supersonic aircraft service. The theories of thermal-gradient diffusion may be found in recent reviews and experimentation in this field by Shewmon,1 Sawatzky,2 Markowitz,3 and Darken and Oriani.4 The basis for Soret thermal diffusion is the "heat of transport", denoted by Q*. This is an energy term for the amount of heat (energy) transferred by atomic diffusion, and can be either positive or negative signifying a driving force for atomic diffusion to the cooler or hotter region, respectively. Experimentally, Q* is determined by plotting the natural logarithm of the point-to-point concentrations after exposure to a thermal gradient vs the respective point-to-point temperatures in units of the inverse absolute temperature scale. The slope of the straight line is Q*/R, R being the gas constant. For the titanium experiments, specimens (3 by 1 by 1/16 in.) of a) commercially pure titanium, b) the 8 Al-1 Mo-1 V titanium alloy, and c) the 6 A1-4 V titanium alloy were exposed to thermal gradients of 6° to 115°C per in. for 18 days at 250° to 550°C. The temperature gradient was in the direction of the 3-in. dimension. The hydrogen concentrations existing after exposure were determined on sections of the specimens by vacuum extraction. Three sections of unexposed sheet of each alloy were analyzed as standards to allow a check for hydrogen

Jan 1, 1965

By Alfred H. Bell

Illinois produced 5 per cent more crude oil in 1934 than in 1933, because there was less curtailment, and. the value of the year&apos;s production at the wells was 35 per cent more than that of the previous year. The average price of Illinois crude oil in 1934 was $1.13 as compared with $0.87 in 1933, an increase of 30 per cent. The quotas of allowable production for Illinois during 1934, as authorized by Oil Administrator Harold L. Ickes, were as follows: January, February, March, 12,000 bbl. per day; April, May, 12,500; June, July, 12,600; August, 12,500; September, October, November, 12,000; December, 11,700. No other restrictions on production were in effect during the year until Oct. 11, when it was found necessary to prorate the fields to 75 per cent, a curtailment of 25 per cent below the quota fixed by the Federal Administrator. On Dec. 1 the curtailment was reduced to 18 per cent and on Dec. 18, to 15 per cent. Production in Illinois by months during 1934 was as follows: Barrels Barrels January...................... 393,000 July........................ 394,000 February.................... 337,000 August..................... 402,000 March....................... 394,000 September.................. 378,000 April......................... 373,000 October.................... 352,000 May......................... 411,000 November.................. 305,000 June......................... 392,000 December................... 321,000 Total ................... 4,452,000 In spite of higher prices for crude oil, fewer wells were drilled in Illinois in 1934 than in 1933 (Tables 1 and 2). Of the 26 wells drilled, 10 were oil producers, 8 were in proved fields and 2 were in a new pool in Wabash County, l½ miles south of the nearest production, one was a small gas well on the Stubblefield anticline in Bond County, one was an input well for repressuring in the Colmar-Plymouth field, McDonough County, and 14 were dry holes, mostly scattered wildcat tests.

Jan 1, 1935

By W. J. Parton

THE efficient recovery and preparation of small sizes of anthracite called No. 4 Buckwheat (3/3 2 by 1/3 2 in.) and No. 5 Buckwheat (1/3 2 in. by 0), present a difficult problem to the anthracite operators. In many instances preparation of these sizes, particularly No. 5 anthracite, is extremely inefficient. In many of the older preparation plants, inadequate facilities, and often none at all, were provided as an integral part of the plant for cleaning this fine anthracite. Consequently, much of the material smaller than s, 32 in. was discarded. As the demand for these sizes increased, facilities for preparing the fine sizes were often crowded into existing structures with consequent sacrifices of capacities and efficiency. In addition to this condition, the methods of preparing the finest sizes are being developed in an attempt to improve their efficiencies. Because the demand for small sizes of anthracite still is increasing, many operators would benefit by investigating and improving the cleaning equipment employed on these sizes.

Jan 1, 1949

By A. L. Sweetser

Experience has shown how difficult it is to obtain information regarding laboratory-tests in connection with the chlorina-tion-process for the extraction of gold from its ores, and I therefore present the following method, somewhat in detail, for the benefit of those who may desire to pursue research work in this field. The ore chosen was a partly-decomposed porphyry, extremely siliceous and comparatively soft, and of an average value per ton of from $25 to $26 in gold and $0.68 in silver. The chemical analysis gave: Fe,O,, 3.35; FeS, 1.5; MnO,, 0.75; ZuCO,, 4; A1,0,, 3.20; H,O, 0.7 ; SiO, and insol., 83.50 per cent. The ore, first crushed to pass a 5-mesh screen, was coned and quartered until a 45-lb. sample was obtained. Samples for assay and analysis, taken from this lot by means of riffles, were crushed to pass a 100-mesh screen. The original sample was divided into 10-lb. lots, of which one was crushed to pass a 10-mesh screen; another through a 12-; the third through a 20-, and the last through a 30-mesh screen. Because of the production of an excessive quantity of fine material it was deemed inexpedient to crush finer than 30-mesh size—a decision the wisdom of which is proved by the data in Table I., showing the increasing ratio of slimes, in proportion as the ore is crushed finer. In order to determine the percentage of fines in the sizes of mesh selected, a weighed sample of ore was taken from each mesh, and a sample from the 10-mesh lot was passed successively through 20-, 40- and 100-mesh screens, and the percentage remaining on each screen determined. This process was repeated with the 12-, 20- and 30-mesh lots, with the results given in Table I.

Jan 1, 1908

By T. Wasson

The same limitations&apos; that characterized 1931 existed in the old fields of Indiana and Illinois during 1932. Prices remained low. The average for the year for Illinois and southwestern Indiana was $1.032 as against $0.852 for 1931 and $1.616 for 1930. In September a curtailment of production of about 25 per cent became effective and was continued to the end of the year. There were no new discoveries and very little wildcatting was done. Considering the age of the wells, and the number still producing, there were few abandonments. The most outstanding thing about the old fields in these states is their long continued productivity. Illinois The fields along the southeast end of the LaSalle anticline had their peak of 33,686,000 bbl. in 1908. In 1932, with a 25 per cent restriction for 355 months, these fields produced 4,661,000 bb1.l There were 52 new completions (most of them in old territory) and of these 33 were dry, 8 were gas, and 11 were oil wells. The new oil wells had a total initial of 102 bbl., or an average of 9.3 bbl. per well. Nineteen of the new producers were in Crawford County. There were about 200 wells abandoned in the old southeast fields in 1932 as compared to 210 in 1931. The greatest number, 86, were in Lawrence County. To the end of 1932, the four major counties—Clark, Crawford, Lawrence and Wabash—had produced almost 394,000,000 bbl. from 92,160 acres. Better than one-half of this was produced in Lawrence County from 26,240 acres. The Dupo area of Sinclair County had no additions to production although four wells were drilled. On the Jacksonville structure in Morgan County, six gas wells with an average depth of 300 ft. were drilled to sands in the base of the Pennsylvanian. They produced an open-flow total initial of 2,000,000 cu. ft. This gas will be developed further to supply a local market.

Jan 1, 1933

By Eckley B. Coxe

I wish to call the attention of the Institute to a peculiar variety of anthracite which occurs in the Buck Mountain vein at our collieries at Drifton, and in the same and other veins in different localities in the anthracite coal-fields. It is known among the workmen as iron-gray or cast-iron. It has a dull, greasy appearance, as if a piece of ordinary anthracite had been rubbed with a dirty and greasy rag and allowed to dry. It was formerly considered a very impure coal containing a high percentage of ash, and was picked out of the coal and thrown away. But the following analysis of it and of its ash, made by Mr. J. Blodget Britton, of Philadelphia, shows that such is not the case, the percentage of ash not being much higher than that of the ordinary anthracites as they are prepared for market. ANALYSIS OF COAL. Water,.........4.36 Fixed carbon, by difference,.. 84.90 Volatile combustible matter,. . 3 48 Ash,..........7.26 100.00 The carbon proved to some extent to be of the nature of graphite, and slowly combustible. ANALYSIS OF ASH. Silica,.........25.66 Sulphur,........ .17 Alumina,........27.03 Phosphoric acid,.......21 Ferric oxide,.......42.83 Alkali, undetermined matter and Lime,.........1.56 loss,.........60 Magnesia,........1.83 Manganous oxide,......11 100.00 We recently collected a quantity of the substance and made a fire with it, in an ordinary stove, which was kept up several days. We found that it burned with intense heat, and apparently as freely as our other coal does. Mr. Britton is probably right in his view, that the difference in appearance is not due to impurities in the coal, but to the fact that the carbon is in a more or less graphitic form, as many of the standard coals are no purer. I bring this before the Institute as I know that a large quantity of this valuable fuel is thrown away every year, on account of its supposed impurities.

Jan 1, 1879

By J. C. Bradley

The relation of annealing temperature to conductivity of copper wire has been determined. Conductivity hard was 98.26 per cent. After a 10-min. heat,ing at 200" C. it was 98.69. By annealing 10 min. at 300" C. a large increase, to 100.93, occurred. Maximum conductivity, 101.15, was attained after a 500" C. anneal; thereafter it decreased to 100.53 after a 950" C. anneal. If copper is gassed the decrease is much more than this. Material and Method The work was done on high grade electrolytic copper, 99.942 per cent, copper plus silver, silver 0.0008 per cent. It was hot-rolled to 1/4 in., then cold drawn to 0.080 in. The wire was cut into 25 5-ft. lengths and numbered 1 to 25 as cut. Four samples were tested hard. The others were wound into 5-in. diameter coils. For the 100" C. heating a coil was put into water, the water brought to . boiling, and the wire kept at this temperature for 10 min. For the higher temperatures the coils were placed in envelopes of sheet copper, a little water added, and the envelopes sealed by folding over the edges twice, and hammering them together. This kept the air out very well. The envelope and wire were brought to the desired temperature; this was maintained for 10 min., then the whole was water-quenched. Results Data from the tests are shown in the table and plot (see Fig. 1); conductivity is referred to the International Annealed Copper Standard at 20" C. Conductivity hard is considerably less than conductivity soft.1 The increase is sharp when the wire anneals. The maximum, 101.15 per cent, in the particular material used, comes at 500º C.; thereafter the conductivity falls to 100.53 per cent. after 950" C. annealing, a drop of 0.62 per cent.

Jan 1, 1927

By I. Javandel, P. A. Witherspoon

The finite element method was originally developed in the aircraft industry to handle problems of stress distribution in complex airframe configurations. This paper describes how the method can be extended to problems of transient flow in porous media. In this approach, the continuum is replaced by a system of finite elements. By employing the variational principle, one can obtain time dependent solutions for the potential at every point in the system by minimizing a potential energy functional. The theory of the method is reviewed. To demonstrate its validity, nonsteady-state results obtained by the finite clement method are compared with those of typical boundary value problems for which rigorous analytical solutions are available. To demonstrate the power of this approach, solutions for the more complex problem of transient flow in layered systems with crossflow are also presented. The generality of this approach with respect to arbitrary boundary conditions and changes in rock properties provides a new method of handling problems of fluid flow in complex systems. INTRODUCTION Problems of transient flow in porous media often can be handled by the methods of analytical mathematics as long as the geometry or properties of the flow system do not become too complex. When the analytical approach becomes intractable, it is customary to resort to numerical methods, and a great variety of problems have been handled in this manner. One such method relies on the finite difference approach wherein the system is divided into a network of elements, and a finite difference equation for the flow into and out of each element is developed. The solution of the resulting set of equations usually requires a high speed computer. When heterogeneous systems of arbitrary geometry must be considered, however, this approach is sometimes difficult to apply and may require large amounts of computer time. The finite element method is a new approach that avoids these difficulties. It was developed originally in the aircraft industry to provide a refined solution for stress distributions in extremely complex airframe configurations. 27 Clough has recently reviewed the application of the finite element method in the field of structural mechanics.6 The technique has been applied successfully in the stress analysis of many complex structures.l, 27, 28 Recognition that this procedure can be interpreted in terms of variational procedures involving minimizing a potential energy functional7 leads naturally to its extension to other boundary value problems. In the field of heat flow, there recently have been introduced several approximate methods of solution that are based on variational principles.2-4, 17 By employing the variational principle in conjunction with the finite element idealization, a powerful solution technique is now available for determining the potential distribution within complex bodies of arbitrary geometry. In the finite element approximation of solids, the continuum is replaced by a system of elements. An approximate solution for the potential field within each element is assumed, and flux equilibrium equations are developed at a discrete number of points within the network of finite elements. For the case of steady-state heat flow, the technique is completely described by Zienkiewicz and Cheung.33 Since the flow of fluids in porous media is analogous to the flow of heat, Zienkiewicz et al. have employed the finite element method in obtaining steady-state solutions to heterogeneous and anisotropic seepage problems. 34 Taylor and Brown have used this method to investigate steady-state flow problems involving a free surface.25 The work of Gurtin has been instrumental in laying the groundwork for the application of finite element methods to linear initial-value problems.12 As a result, Wilson and Nickell have recently

Jan 1, 1969

By Henry Mackay

THE interesting paper recently submitted by Messrs. Tobelmann and Potter&apos; shows that chemical problems have developed which are of great interest in this new and important branch of metallurgy. Those who realize what a process of this kind really involves will agree that it deserves a better name than "leaching process." The word leaching conveys the idea that the copper is simply leached out of the ore with acid and then precipitated on iron; the chemistry of such a process would be of little interest. As, however, during the first year&apos;s operation of this plant 24,400,532 lb. (11,067,837 kg.) or about two-thirds of the produce, was electrolytic copper, while 7,992,033 lb., or about one-third, was cement copper, it would seem more appropriate to term the process electrochemical. It further appears, from the particulars given, that efforts have been made to have the entire production in the form of electrolytic copper. -This could be done if the chemistry of the problem were kept in balance, so that it would not be necessary to discard any solutions that carried copper and acid of commercial value. A process, such as that under consideration, in which the copper is precipitated from solution by electrolysis, the solvent being at the same time regenerated, is one that requires special chemical and electrochemical knowledge and experience if all the -copper in solution that has been extracted from the ore is to be successfully and economically produced as electrolytic copper. The object of this paper is to discuss, from the practical and theoretical standpoints, the chemical and electrochemical problems involved in the working of a process of this kind, and&apos; which must be solved to keep it in chemical and electrochemical equilibrium. In such a process, if the chemical balance is maintained, a solution can be used alternately as a

Jan 9, 1919

By Mark R. Lamb

THE treatment of slime is of special interest to those engaged in cyaniding gold- and silver-ores. The usual practice is to make as small a percentage of slime as possible. In many instances the slime is given no treatment, but is impounded in dams in the hope that the future will develop some method of economically treating this product. The filter-press was the first step upward from ordinary decantation, but, on account of heavy labor-charge and high cost, its use has been limited to high-grade material. The slime at the Combination mill at Goldfield averages perhaps $20 per ton, and although the values are quickly dissolved the filter-press installation was not entirely satisfactory, resulting in the erection of the canvas-cell filter, developed by Chas. Butters and his staff. This filter is a great improvement over the filter-press, and the following description of it will be of interest to those engaged in treating slime produced in crushing ores, especially in view of the fact that, by the use of this filter, slime can be treated at a lesser cost and with a higher percentage of gold- or silver-extraction than in the ordinary treatment of sand; and, moreover, the initial outlay for an all-sliming plant is less than that for the ordinary sand- and slime-plant. The economy of construction of the Butters filter-plant is clearly shown in Figs. 1 and 2, which illustrate the 20-frame filter of 40 tons capacity, now being installed by the Nevada Goldfield Reduction Co. In this construction the slime-pump is so connected that it can pump to or from either tank or the filter by changing the valve-settings-a combination which is necessary in this particular installation, since sufficient fall is not available for filling and discharging the filter by gravity. Ordinarily, a slime-plant comprises: a filter-box with frames

Jan 1, 1907

By Warren W. Jamar, Philip D. Pearson

IN recent years, there have been many changes in mining operations in the Lake Superior district. To follow these trends on the Menominee Range of Michigan, information has been assembled from all of the iron informatior]mining operations in the area. There are 15 operating underground mines in the Iron River-Crystal Falls area of the Menominee Range. Within the past two years, two idle properties were reopened pasttwoyears,and are now producing, and a third and fourth are being reopened. Also, there are two siliceous openpits operated by independent companies outside this immediate area. Six companies operate the underground mines, employing some 1850 employees. Table I shows pertinent facts about these properties. During 1949, the largest mine in Iron County shipped 571,287 tons, and one of the newer mines shipped 39,378 tons, with a range total to 3,535,-373 tons. Since the Menominee Range was opened in the 1870&apos;s, the mines in Iron County have shipped 85,890,922 tons. From an operator&apos;s viewpoint rather than a geologist&apos;s, the ore is&apos; classified as semi-hard, composed of hematite and limonite. It is not as soft as the ores of the Marquette Range nor is it as hard as the hard ores of the Marquette and Vermillion Ranges. The ore bodies have slate hanging walls and slate footwalls. In most cases the hanging walls and footwalls are soft and high in sulphur. The sulphur comes from pyrite, and these slates will ignite when piled more than 6 to 8 ft high. Ore is mined on this range by: 1—Sub-level stop-ing; 2—Shrinkage stoping; 3—Sub-level caving; 4— Block caving; 5—Top slicing. The predominance of these methods is in the order named. Underground drilling is important in the mining cycle. Some changes made and trends toward future changes fall into four categories: Drill bits, drill steel, drill machines, and compressed air pressures. Several types of bits have been tried and are in use. They include the detachable tungsten carbide, insert bit; the intraset steel bit, which is a conventional steel rod with tungsten carbide insert; the one-use bit; and the multiple-use bit. For many years, detachable multiple-use bits have been standard. In tests conducted recently to im- prove drilling efficiency, this bit was used as the basis for comparison. Under existing conditions, a multiple-use bit can be resharpened about three times before it is discarded. A thorough test of 2-in. tungsten carbide threaded bits was conducted under various ground conditions. 1—The drilled footage ranged from 48 to 600 ft per bit; averaging 357 ft per bit. Under these same conditions, a multiple-use bit ranged from 8 to 80 ft per bit. 2—The bit cost was greater for the insert bit in each case. 3—The average drilling speed for the insert bit was 12 in. in 62 sec and for the multiple-use bit was 12 in. in 64 sec. In a second test, 2V4 -in. tungsten carbide bits with the large 1 3/16-in. thread were used in moderately soft ground on a 152-lb drifting drill on a long feed jumbo. 1—The drilled footage ranged from 450 to 5000 ft per bit, averaging 1810 ft per bit. Under these same conditions, a multiple-use bit averaged 64 ft per bit. 2—The bit cost was reduced by the use of the insert bit. 3—No increase in drilling speed was recorded. 4—Minimum footage obtained was caused by thread failure. To improve the thread life, thread size on the rod was increased and the bit was attached to the rod with a pipe wrench. After this, bits failed in equal proportions because of cracked skirts, broken inserts, and gage loss. Tungsten carbide bits are now used in the operation where this second test was conducted because labor costs were lowered as a result of reducing the number of bits being changed by the miners. At the same operation and under the same conditions as the second test, 1Y4-in. insert bits with standard 1-in. threads were used. These bits did not drill much more than 300 ft before thread failure and were then welded to the rods and used until total failure. Sometimes this footage was considerable, sometimes it was not. Chisel-type 2%-in. insert bits were

Jan 1, 1952

By J. S. Marsh

TUESDAY, Feb. 16, was no day for strolling along the cold sidewalks of New York, and a large number of metallurgists sat down with pleasure to the warming task of wiping a few soldered joints. Presented by a joint-wiper of the modern school, G. M. Bouton, of the well-known team of Schumacher, Bouton, and Phipps, the initial paper brought into focus the theme of conservation of strategic metals and described the technique of making the fillet-type joint now employed by the Bell System. Using an over-all average of only 40 per cent of the solder formerly used by the conventional method. this important development bids fair to stick when the war is over. D. L. Martin and E. R. Parker then described the embrittling effect of hydrogen on silver previously heated in oxygen and the less serious but troublesome result obtained under the converse conditions. An interesting example of grain growth restriction created additional material for the lively discussion that ensued among those who have encountered one or another of these phenomena in silver and copper.

Jan 1, 1943

By F. G. Smith

A few years ago, the writer encountered a problem that, at first, seemed to be due to peculiar conditions affecting grain growth. Large cups made from heavy metal failed in the first drawing operation in the process of making seamless tubes. The metal, as cast, appeared to be sound and strong; it rolled successfully and withstood the first cupping operation, but on the first draw it failed, with a crystalline fracture. The failure appeared in the slightly worked part of the bottom of the cup, and microscopic examination revealed exceptionally large grains. Knowing the general conditions governing recrystallization of brass, which were later published by Mathewson and Phillipsll an investigation was outlined with the idea of including various conditions under which new grains might form, and which would include the effect that a previous anneal might have upon the anneal following. These conditions were produced by annealing specimens of brass at five different temperatures, indenting them with a 10-mm. ball under four different pressures, and then reannealing at each of the five temperatures five specimens each of which had been annealed at one of the five temperatures. Preparation of Specimens The material used was cartridge brass 0.400 in. thick, having the following composition: Copper 66.60 per. cent., zinc 33.35 per cent., lead 0.02 per cent., iron 0.03 per cent. This was rolled with 35 per cent. reduction after a 700" C. anneal. Fig. 1 shows the structure of this original bar on which all subsequent anneals were made. Pieces 1 in. (2.5 cm.) wide and 3 in. long were prepared and annealed for 1/2 hr. at 450°, 550°, 650°, &apos;750°, and 850" C. Each of these pieces are indented under the Brinell test with a 10-mm. ball at 500, 1000, 2000, and 3000 kg. pressure. Then, sets of five pieces from each of the original anneals were reannealed at 450°, 550°, 650°, 750°, and 850" C.

Jan 1, 1921

By Robert S. Baker

It has been demonstrated in the laboratory by A. J. Phillips1 that a transformation or conversion from beta directly to alpha may take place in a brass of 61 to 62.5 per cent copper content. The completion of the transformiation is dependent on a rapid rate of cooling from the all-beta field through the alpha + beta range to the alpha field. Phillips states that in a slowly cooled alloy containing 62 per cent copper and 38 per cent zinc the copper content of the beta is progressively decreased from 62 to 56 per cent by precipitation of alpha. Rapid cooling tends to prevent the separation of alpha with a copper content of more than 62 per cent by reducing to a minimum the time required for passing through the alpha + beta range. Upon crossing beyond the (alpha + beta) (alpha) boundary to the all-alpha region below, the material is transformed from beta to alpha. It, is essential that there be no change in composition. Phillips obtained his results by quenching a 62:38 copper-zinc alloy from 850" C. in iced brine at -8" C. No reference to the occurrence of this transformation in a manufacturing process has been found in the literature. An investigation of the microstructures of a number of hot forgings made from leaded brass rods yielded one forging in which this striking conversion from beta to alpha had occurred. The purpose of this paper is to describe the transformation and certain conditions under which it may occur during the hot pressing of brass. The conversion was noted in a shape forged from a leaded brass rod, the composition of which was: Cu, 60.26 per cent; Zn, 37.86; Pb, 1.88. In this study the lead content was disregarded and the alloy was considered to be equivalent to an alloy of 61.40 per cent copper and 35.60 per cent zinc (9812 parts = 100 parts). The possibility that the lead might obstruct or accelerate the precipitation of alpha was not studied. The lead appears as black globules in the photomicrographs and has a negligible solubility in the alloy.

Jan 1, 1932

By O. D. Sherby, J. E. Dorn

SEVERAL years ago Zener and Hollomon1 suggested that the flow stress of metals might be related to the temperature and strain rate in accord with the functional equation: s=s(eeh/rt) [1] at the same state. The Zener-Hollomon relation also contains the significant tacit implication that the energy for activation, AH, is substantially independent of the state of the material. The utility of this method for correlating creep data with tensile data was illustrated in a preliminary reportL on the effect of alloying additions on the secondary creep rates of binary a solid solutions in aluminum as shown for Al-Mg alloys in Fig. 1. Not only do the secondary creep and ultimate tensile properties for each alloy correlate well on this plot but in addition the activation energy, AH = 17,900 R cal per mol. is identical for the various compositions. Similar types of curves correlating the secondary creep rates at 422°K (300°F) with ultimate tensile data were also obtained for a series of dilute a solid solutions of copper, germanium, zinc, and silver in aluminum. In all cases the activation energy for creep, AH, was found to be equal to about 17,900 R cal per mol independent of the type of alloying element or its concentration. The coincidence of the activation energies for these alloys is probably due to the fact that the activation energies for creep are rather insensitive to small composition changes. Alloying additions, as shown in Fig. 1, however, increased the stress necessary to obtain equivalent values of ee?H/RT. Thus the stress level in curves of the type represented by Fig. 1 gives the relative creep strengths of the various alloys. Inasmuch as these correlations between creep and tensile data were obtained for creep tests at 422°K, it appeared advisable to ascertain the range of secondary creep rates and temperatures over which correlations between creep and tensile data could be made on the basis of the Zener-Hollomon relationship. If, for example, the activation energy changes with different ranges of creep temperatures, the utility of the proposed analysis would be severely weakened. But if AH is constant not only for all dilute alloys, but also over wide ranges of temperature and secondary creep rates, confidence will be developed not only in the broad utility of the Zener- Table I. Chemical Analysis&apos;:&apos; and Grain Size of Alloys Mean Grain Residual Impurities. Wt Pct Diam- Alloying Atomic-eter, Element Pct Si Fe Cu Mg Mn mm Aluminum 99.987 0.003 0.003 0.006 0.001 0.25 Magnesium 1.617 0.003 0.004 0.006 0.26 Copper 0.101 0.003 0.003 0.0006 0.001 0.29 Zinc 1.616 0.003 0.005 0.007 0.001 &apos;0.26 * The authors express their appreciation to the Aluminum Company of America for the preparation and chemical analyses of these alloys. Hollomon relationship, but also in its theoretical justification. The following investigation was instituted in order to ascertain the range of validity of the Zener-Hollomon relationship when it is applied to creep and tension data. Materials, Equipment, Technique In view of rather extensive correlatable data now available on the plastic properties of a series of binary a solid solutions of magnesium, copper, germanium, zinc, and silver in aluminum, these alloys were again selected for the present investigation. Previous reports have already covered the tensile properties of these alloys at subatmospheric temperatures," and at elevated temperature," as well as their fatigue properties at atmospheric temperatures, nd their creep properties at 422°K.&apos; Resistivity measurementsa as well as precision lattice constant determinations? evealed that these alloys are a solid solutions. After homogenization. 0.100 in. thick sheets were rolled to 0.070 in. in thickness and recrystallized to about the same grain size. Since the details of these treatments were reported previously," they will not be repeated here. In order to appropriately reduce the scope of creep tests in this investigation only the typical alloys shown in Table I were investigated. All creep specimens were machined such that their tensile axes were in the rolling direction of the 0.070 in. sheet stock. The gage section was 2 in. long and 0.500 in. wide with a reduced section of 3.50 in. Creep strains were measured by means of rack and pinion type extensometers with a sensitivity of 0.005 in. per division. Readings were estimated to 1/10 of

Jan 1, 1953

E. K. Landis, Philadelphia, Pa. (communication to the Secretary) : Mr. Firmstone&apos;s paper is of great interest; but he has unfortunately otnitted to state the most important point, viz., the percentage of sulphur in the two materials he compares; and this omission vitiates the conclusions which he draws. Comparing by grade, instead of silicon-contents (as in his Table III.), the iron made using limestone with that made using dolomite, we find for gray-forge the average of four analyses under limestone to be, Si, 0.644; S, 0.089 ; while one analysis under dolomite gives Si, 0.508 ; S, 0.070. For No. 2 iron, the limestone flux gives, as an average of 19 analyses, Si, 1.107; S, 0.051; while the average of 4 analyses made with dolomite flux gives Si, 0.630; S, 0.056. It will be observed, that no No. 1 pig is given under limestone, while 14 analyses appear under dolomite, averaging Si, 0.950 ; S, 0.028. As nothing is said about changed conditions, it is Fair to presume that the ore and fuel, as well as the blast-temperature (which is stated to have been uniform at about 750&apos; F.) remained practically the same; and since the sulphur in the two fluxes is not given, it is impossible to know whether the lower sulphur for equal silicon-contents is due to the use of dolomite or to other conditions. The use of dolomite would produce a more fusible cinder, and the furnace would be hotter than when using limestone; therefore, we might expect to see a grayer iron. The amount of So. 1 iron made with dolomite seems to confirm this supposition; and, under these conditions, we might expect more of the sulphur to be volatilized, and to pass off in the gases. The easier fusibility of the cinder would also permit more rapid driving; and this should reduce the amount of silicon and sulphur in the iron, as the amount of reduced metalloids in the pig is directly proportional to the length of time it remains in the reducing-zone.

Jan 1, 1895

Mining and Metallurgy of Lead and Zinc, AIME Vol. 121, edited by Dr. C. R. Hayward in 1936, remains a document of importance today even though 34 years have passed in the meantime. Since nothing in this world seems to be permanent, however, and progress brings new and better ways to do things, a two-volume set has just been published to bring the state of the art of 1936 up to date. This two-volume set, Mining and Concentrating of Lead and Zinc and Extractive Metallurgy of Lead and zinc, incorporates the papers to be presented during the Proceedings of the 1970 World Symposium on the Mining and Metallurgy of Lead and Zinc. The Symposium is being held October 20-24, 1970, in St. Louis, a site near to the famous Lead Belt of southeast Missouri. Some eighty papers are bound in these two volumes covering exploration, geology, mining, concentrating, roasting, smelting, electrolytic processing, residue fuming, refining, etc. All of this is laced with data on tonnages, processes, assays and efficiencies obtained, and the man-hours and equipment needed to achieve these performances.

Jan 1, 1970