Search Documents

By John H. Hall

The Frémont test for measuring the energy consumed in breaking a notched bar of steel is not so well known in this country as it deserves to be. The test specimen used in this test is about # by 6 by about 16 in., notched with a hack saw on the lower side to cause the piece to break at a fixed point. A weight of 10 kg. falling 4 m., and provided with a knife or chisel which strikes the specimen, breaks the test piece by impact. The residual force in the falling weight after it has broken the specimen is recorded by a suitable device, and the difference between the total energy and the residual energy of the weight (in kilogrammeters) is the force consumed in breaking the specimen. An experience of several years with the Frémont testing machine has shown its great value in readily detecting brittleness not revealed by tensile testing or slow bending testing. In this paper it is proposed to discuss (1) the supersensitiveness of the test as applied to cast steel and (2) its value in revealing the effect of heat treatment under certain conditions. In testing coupons cut from castings heat treated by quenching and annealing, attention was drawn to the wide variations in the value of the Frémont test of specimens cut from different parts of the coupon. The latter was of the form and dimensions shown in Fig. 1, and Fremont test pieces were cut from two parts of this coupon, marked A and B in that figure. The results of the tests are shown below, tests A and B in each instance being from the same coupon: A. B. A. B. Coupon. Kilogram- Kilogram- Coupon. Kilogram- Kilogram- meters. meters. meters. meters. 1,........ 12.0 12.5 9,........ 27.5 32.5 2,........ 11.0 32.5 10,........17.5 31.0 3,........ 11.5 30.0 11,........ 14.5 31.0 4,........ 20.0 33.0 12,........ 15.0 27.5 5,........ 17.5 33.0 13,........ 19.0 30.0 6,........ 17.5 20.0 14,........ 17.5 25.5 7,........ 17.5 13.0 15,........15.0 30.0 8,........ 10.0 30.0

Jan 1, 1914

By Hallet R. Robbins

KOREA, the ancient " Hermit Kingdom," is a peninsula jutting out from the coast of eastern Asia. By the natives it is called " Chosen," which, translated, means " Land of the Morning Calm." It lies between the Yellow sea and the Sea of Japan. On the north it is separated from Manchuria and the Russian province of Primorsk by the Yalu and Tiumen rivers ; on the south the Korean straits interpose a rough voyage of 120 miles to the nearest point in Japan. The entire country is situated between the parallels of 34° and 42° N. latitude. The surface of the country is made up of successive ranges of unglaciated mountains, separated by narrow, fertile, and more or less densely populated, valleys. Through all the obscure centuries of its history, Korea has succeeded in maintaining a monastic seclusion, over which, from time immemorial until the late Chino-Japanese war in 1894, China exercised a shadowy sovereignty. Although Korea had been forced into slight foreign contact previously, her first foreign treaty was signed with Japan in 1876. Under the restraining guardianship of China, the Japanese treaty bore but insignificant innovations for Korea; but when, in 1883, a treaty was made with the United States, the first of the western nations, a decade after the American gunboats, under Commodore Rodgers and Lieutenant Schley, forced their way up the Salee river, shooting daylight through the ancient walls and fastnesses, Korea awoke from her sleep of 4,000 years. The Korean peninsula suddenly became the arena where rival nations' enterprises and individuals met in fiercest conflict. Out of this struggle grew two singularly successful American

Jan 7, 1908

By George Bain

SOME problems concomitant with commercial exploitation of marble are presented as examples of interesting, useful and profitable fields for application of scientific knowledge. The marble industry is only one such field and is selected because its varying new aspects are familiar to the author. However, what is true for marble is equally so in principle for many industrial minerals. The problems of any stone industry are to maintain markets, create new outlets for stone already in demand, and develop varied uses for varieties that are not so popular. Here the geologist has a different role from most of his colleagues in metal mining. The producing branch may ask about the expectable variation in thickness or size of a deposit as development proceeds. The stock department may call for the available amount of a given type of stone before accepting a large order. The sales force requires data on the use for stone from certain parts of deposits in order to divert grades to the most suitable use. The service depart-ment wants defects rectified and the cause determined to avoid recurrence. The mills want data on durability and cutting quality of abrasives. The geologist occupies no special department; he is on general call, as may be illustrated by a few types of problems that may be classified as: (1) dominantly geological in character, (2) dominantly chemical in character, (3) dominantly physical in character.

Jan 1, 1940

By R. Ingerson

Bore surfaces of used guns commonly show a pattern of cracks in various degrees of development. It has been suggested that these cracks may aid erosion by providing channelways for the gases, eventually leading to the tearing out of blocks of metal. Under the general studies of gun erosion conducted at the Geophysical Laboratory it appeared desirable to consider this factor, and to determine the resistance to surface cracking offered by gun steel and by various other materials that might be used in the bores of guns. Method and Apparatus In order to make such a determination it is necessary to have (I) an arrangement in which the surface to be studied can be subjected to conditions similar to those in a gun with respect to temperature, pressure (developed by explosion gases), composition of the gases and length of time the surface is exposed to the gases; and (2) a specimen that can be examined readily after any number of shots, and then fired again, if necessary. The first of these conditions can be met by using an explosion vessel designed by H. S. Roberts of the Geophysical Laboratory. Fig I shows a cross-section of the apparatus. The "gun" G from which the charge is fired is made from the receiver of a caliber 0.30 army rifle, M1903, and the charges are prepared in caliber 0.30 cartridge cases. The test specimen S is held in place by a cone-shaped plug P and by a steel bridge B which is bolted to the outside of the explosion vessel on either side of the section shown. The plug, in turn, is held in place by a screw collar C. Maximum pressure is controlled by a brass rupture disk R. Part of the explosion gases flow past the two flat areas on S. Temperature and composition of gases, and the time before the rupture disk breaks, can be controlled by amount and kind of powder used, and pressure can be controlled by using rupture disks of different thickness. While the explosion vessel used was not designed so that temperature and pressure could be measured, in other vessels of closely similar size and shape containing proportionate charges of the same kind of powder as that used for standard testing procedure, values of 2700°K and 50,000 psi were obtained. Since the orifices past the flat areas on the plug are small compared to the rupture disk hole (I:I6), most of the gas goes out through the rupture disk when it breaks. The amount that goes by the plug depends on (I) the pressure attained before the rupture disk breaks and (2) the time it takes for this pressure to be built UP. The second condition (examination at will after any firing) is met by using for specimens short rods that have flat areas ground on opposite sides. These flat

Jan 1, 1949

By R. Ingerson

Bore surfaces of used guns commonly show a pattern of cracks in various degrees of development. It has been suggested that these cracks may aid erosion by providing channelways for the gases, eventually leading to the tearing out of blocks of metal. Under the general studies of gun erosion conducted at the Geophysical Laboratory it appeared desirable to consider this factor, and to determine the resistance to surface cracking offered by gun steel and by various other materials that might be used in the bores of guns. Method and Apparatus In order to make such a determination it is necessary to have (I) an arrangement in which the surface to be studied can be subjected to conditions similar to those in a gun with respect to temperature, pressure (developed by explosion gases), composition of the gases and length of time the surface is exposed to the gases; and (2) a specimen that can be examined readily after any number of shots, and then fired again, if necessary. The first of these conditions can be met by using an explosion vessel designed by H. S. Roberts of the Geophysical Laboratory. Fig I shows a cross-section of the apparatus. The "gun" G from which the charge is fired is made from the receiver of a caliber 0.30 army rifle, M1903, and the charges are prepared in caliber 0.30 cartridge cases. The test specimen S is held in place by a cone-shaped plug P and by a steel bridge B which is bolted to the outside of the explosion vessel on either side of the section shown. The plug, in turn, is held in place by a screw collar C. Maximum pressure is controlled by a brass rupture disk R. Part of the explosion gases flow past the two flat areas on S. Temperature and composition of gases, and the time before the rupture disk breaks, can be controlled by amount and kind of powder used, and pressure can be controlled by using rupture disks of different thickness. While the explosion vessel used was not designed so that temperature and pressure could be measured, in other vessels of closely similar size and shape containing proportionate charges of the same kind of powder as that used for standard testing procedure, values of 2700°K and 50,000 psi were obtained. Since the orifices past the flat areas on the plug are small compared to the rupture disk hole (I:I6), most of the gas goes out through the rupture disk when it breaks. The amount that goes by the plug depends on (I) the pressure attained before the rupture disk breaks and (2) the time it takes for this pressure to be built UP. The second condition (examination at will after any firing) is met by using for specimens short rods that have flat areas ground on opposite sides. These flat

Jan 1, 1949

By S. Frederick Ravitz

IN most applied sciences there are two distinct methods of carrying out research and development work. One of these, the theoretical, attempts to solve problems that may arise and to predict facts of practical importance by the application of the various laws of science, the other, the experimental method, attempts to each the 'same goal by obtaining data and trying out various processes in the laboratory. Since individuals frequently find themselves better adapted for one or the other type of procedure, it is natural that -two groups should 'arise, both working toward the sane objective but with somewhat different points of view, although many in each group are thoroughly competent in both fields. Metallurgy, in particular, offers an excellent opportunity for a comparison of the two methods.

Jan 1, 1935

By N. Parlee, V. C. Kashyap

The solubilities of nitrogen in liquid iron and liquid Fe-Ni, Fe-Mo, Fe-V, and Fe-Mo-V alloys were measured by the Sieverts method. Measurements were made at 1600° to 1800°C on binary alloys up to 20 pet Ni, 10 pet V, 10 pet Mo; and on ternary alloys containing 0 to 3 pet V with 0 to 5 pet Mo. The results on liquid iron confirm that Sieverts' law is obeyed in the range 50 to 750 mm pressure. The measured solubilities and their temperature coefficients are in general agreement with other modern authors. The logarithms of the activity coefficients of nitrogen in the binaries are approximately linear functions of the pet of alloying element. A method suggested by Wagner, Chipman, and others for predicting gas solubilities in complex alloys from solubility data on binaries was applied to the Fe-Mo-V alloys. Reasonably good agreement was obtained between calculated and experimental solubilities. NITROGEN'S solubility in liquid iron has been studied by a number of investigators. It is reasonably well established that the solubility of nitrogen follows Sieverts' law at least up to 1 atm partial pressure and that the solubility increases gradually with temperature. The solubility of nitrogen in Fe-X binary liquid systems has been investigated in only a few cases. Only the systems Fe-Cr,3-5, 7 Fe-V,3 Fe-Mn,3, 5 Fe-Ni,3, 5 Fe-Si,B, H Fe-C, L, H and Fe-P4 appear to have received any study. The only work on liquid Fe-V was done by Brick and Creevy.3 This was limited to 13.5 pet and 26.5 pet V, but no exact temperatures were recorded. No work whatsoever appears to have been done on liquid Fe-Mo alloys and even work on Fe-Ni alloys is rather scant. The work on liquid ternary systems is still more limited, and the only publication available appears to be that of Wentrup and Reif,7 who studied the Fe-Cr-Mn and Fe-Cr-Ni alloys. Rassbach, Saunders, and Harbrecht17 have reported work on the solubility of nitrogen in stainless steel but this was not a systematic study of any particular system. Commercial alloys usually contain several alloying elements. Thus, it often becomes important to be able to predict the nitrogen solubility in systems containing two or more added elements without the necessity of making measurements. Wagner,14 Chipman," Darken and Gurry," and Morris and Buehl 14 have suggested means by which this may be accomplished, and Langenberg14 has recently applied one of these methods to nitrogen solubility in complex liquid alloys. This paper reports the results of nitrogen solubility determinations on Fe-Ni, Fe-Mo, Fe-V, and Fe-Mo-V alloys and compares calculated and experimental solubilities in the ternary alloy. Attempted measurements on Fe-Cr alloys were not successful by the experimental method employed. Experimental Method The general method of solubility measurement was that of Sieverts.' The apparatus and procedure were essentially the same as used by Liang, Bever, and Floe."' The equipment consisted of a small vacuum furnace heated by a 6 kw induction unit, gas measuring apparatus, and a gas purification train. The crucibles used were Norton Alundum with alumina sand around them for insulation. The crucibles were charged with 100 to 200 g of material, about 180 g or nearly filling the crucible being found most satisfactory. Hot volumes were determined with argon and ranged from 95 to 130 cu cm (stp). Temperature measurements were made with a Leeds and Northrup optical pyrometer which was calibrated periodically against the melting point of iron in the same apparatus."-'* Good quality nitrogen, hydrogen, and argon gases were further purified and dried in standard purification trains. The sources of the high purity iron and other alloying elements used were as follows:

Jan 1, 1959

By George Macready

TRINIDAD, British West Indies, is an island near the north coast of South America, situated between latitudes 10° and 11° N:, and. opposite the numerous outlets of the Orinoco River Delta. It is separated from Venezuela by the Gulf of Paria (salt, water) and straits over 5 mi. (8 km.) wide. The area of the island is approximately 1750 sq. mi. (453,- . 250 hectares) and the population is approximately 400,000. The climate is tropical with an annual rainfall of from 45 to 60 in. (114 to 152 cm.). The oil fields consist of several units, or fields, located in the southern half of the island. Approximately 90 per cent. of the total production has been yielded by fields situated within 7 mi: (11.3 km.) of the famous asphalt lake and on the southwest peninsula. The most important producing fields, or units, are the following, which are shown on the accompanying map: Brighton, or Pitch Lake Field, operated by the Trinidad Lake Petroleum Co., Ltd., is situated beside the famous Pitch Lake; it, even encroaches on the lake. Vessigny Field, operated by the Trinidad Lake Petroleum Co., Ltd., is situated 2 mi. (3.2 km.) south of Pitch Lake. Lot One Field, operated by the Petroleum Development Co., Ltd., the United British Oilfields of Trinidad, Ltd., and Stollmeyer, Ltd., is situated 3 mi. south of Pitch Lake upon Lot One of Morne 1'Enfer Forest Reserve and adjoining properties. Parry Lands Field, operated by the United British Oilfields of Trinidad, Ltd., and the Petroleum Development Co., Ltd., is situated 3;2 mi. south of Pitch Lake on Lot Three of Morne l'Enfer Forest Reserve and adjoining properties. Point Fortin Field, operated by the United British Oilfields of Trinidad, Ltd., is situated at Point Fortin, 6 mi. southwest of Pitch Lake. Fyzabad Field, operated by Trinidad Leaseholds, Ltd., is situated several miles southwest of Fyzabad Village and 6 mi. south-southeast of Pitch Lake. Barracpore Field, operated by Trinidad Leaseholds, Ltd., is situated several miles south of. San Fernando and 15 mi. (24.14 km.) east of Pitch Lake.

Jan 9, 1920

By C. H. Brehaut, W. N. Taylor, R. S. Douglas, H. A. Shannon

THE name for this new method of mining is derived from a composition of Horizontal, Radial, Diamond, and the drilling is from raises. This method, worked out at Copper Mountain, B.C., is believed to be distinct in many features from other known methods. GEOLOGY The ore deposits of Copper Mountain are related to the Copper Mountain stock, which is an ideal example of the magmatic differentiation in that it grades from a basic gabbro at the border to an almost pure orthoclase-pegmatite core. The "contact" ore bodies lie along the contact of the gabbro and an older complex of volcanics and sediment termed the "Wolfe Creek" formation. These older rocks, collectively referred to as greenstone, had been fractured prior to the intrusion of the stock and were highly metamorphosed during the intrusion. The "outlying" ore bodies are somewhat different in character, though a similar structural pattern prevails. It is believed that a deep-seated magma of which the Copper Mountain stock is a part has given off solutions that caused a partial granitization of some of the volcanics. Mining problems are caused further by the presence of a series of soft barren dikes intersecting a great many of the ore bodies, which are about 30 ft. wide, strike north-south, and dip at a high angle to the east; and are further increased by the presence of four major faults, with a great many minor faults running at acute angles from them. Fault zones average 8 ft. in width, and consist of gouge and breccia. They strike northeast and dip steeply to the northwest. The faults cut through the ore zones and the dikes, and continue on into the gabbro. The general mine structure with two types of ore bodies, bounded by weak walls and intersected by several series of soft barren dikes and major faults, indicated that a method of mining should be devised that would remove the ore at low cost with the least disturbance of the waste walls and dikes. THEORETICAL ESTIMATE OF STOPING WITH THE DIAMOND DRILL After consideration of various methods, the most suitable one appeared to be horizontal drilling to break the ore in a manner similar to shrinkage stoping. Drilling vertical holes or rings from a bench and breaking to an open slot was eliminated because the weak walls of ore, dike or waste would not permit this type of opening. It was then decided to drill either horizontal radial holes from a raise or parallel holes from a slot cut across the ore body. After discussion, the latter method was believed unsuitable, for the following reasons:

Jan 1, 1945

By Oscar Weiss

An aerial magnetometer survey was carried out by the author's geophysical organization over the Vredefort dome, where Witwatersrand beds are wrapped around a granite plug 25 to 30 miles in diameter. The well- known magnetic shales of the Lower Witwatersrand system (to be referred to as LWW) give strong negative anomalies over the out-cropping portion of the dome. This is unusual as these same shales -cause positive anomalies over large areas near Johannesburg and along a strike of 130 miles between the East Rand and Klerksdorp. It is suggested that the negative polarization is caused by heat and stresses connected with the doming. This negative polarization of sedimentary beds, which usually cause positive anomalies, is a good example of how "magnetic lows" can be caused by "structural highs." Significant magnetic anomalies should be tested by gravity and seismic methods irrespective of the sign of the anomalies.

Jan 1, 1949

By G. K. Manning, E. R. Stein, E. E. Underwood

Columbium, carbon. and nickel additions were made to iron-base alloys with 20 pct CY. The effects on microstructure, precipitation-hardening characteristics, and High-temperature properties were investigated by means of metallographic, hot-hardness, and magnetic measurements. An austenitic alloy consistilzg of Fe-20Cr-14Ni-0.8C-2.5Cb had higher hot-lzaciness at 1700°F than the other alloys investigated. Its favorable standing is attributed to an enhanced interaction of Cb and Cr4C particles dispersed within a stable austenitic matrix. FOR the past 20 years, cobalt- and nickel-base alloys have been used for the more stringent high-temperature applications because of their excellent creep resistance. Although their performance is quite satisfactory, other base materials must be considered for large tonnage, low-cost applications such as for the automotive gas turbine. Iron-base alloys are also used extensively, but at somewhat lower temperatures, primarily because of the instability of particles or because precipitation occurs at relatively low temperatures. Since unusual stability has been reported for Fe-Cb and Cb-C compounds.1-3 it was hoped that effective amounts of these compounds could be taken into solution at temperatures just below the melting range, then precipitated upon reheating. Actually, strengthening was found to occur by both precipitation hardening in some alloys and by phase transformations in others. Among the alloys investigated, that with the best high-temperature properties owes its strengthening to a combination of carbide particle interaction and a relatively stable austenitic matrix. EXPERIMENTAL PROCEDURES Small preliminary melts of about 100 g were made in a vertical Glotube furnace, using alundum crucibles and an argon atmosphere. Alloys weighing 35 lb were melted in a basic-lined induction furnace, also under argon. The compositions of the alloys are given in Table I. The nickel-free alloys were usually ferritic, while those containing nickel were generally austenitic. Depending upon the particular heat treatments, or the combination of alloying elements, two-phase alloys of ferrite and austenite could be obtained. In the following text, however, the nickel-free or nickel-bearing alloys are referred to simply as either ferritic or austenitic alloys respectively. The small ingots were swaged at 2000°F, in steps, to rods of approximately 3/16-in. diam. The large ingots were forged at 2100°F to 1-in. sq bars. No difficulties were encountered in swaging or forging any of the alloys to as much as 90 pct reduction in area. For heat treating at temperatures above 2000°F, specimens were sealed in quartz tubes under a partial pressure of helium. No special precautions were found to be necessary at lower temperatures. Intermetallic compounds in the preliminary alloys were identified by means of X-ray diffraction measurements. Correlation of these results with micro-structural characteristics (such as color, shape, size, and location) of the compounds aided in their identification. Magnetic susceptibilities were also obtained at room temperature with a Magne Gage instrument after the various heat treatments. To

Jan 1, 1962

Domestic: Middle West-,11.. B. Newcombe Eastern District-J. French Robinson1 Kansas-Henry A. Ley 2 Oklahoma-Henry A. Ley 3 Texas, except Gulf Coast and Panhandle-M. G. Cheney 5 Texas Panhandle-W. E. Hubbard and H. E. Crum 6 Gulf Coast-L. P. Teas 7 South Arkansas, North Louisiana and Mississippi-H. K. Shearer 8 Foreign Mexico-V. R. Garfias and C. 0. Isakson 9 Canada-Line M. Farish 10 Venezuela-C. W. Hamilton 10 Colombia-J. T. Duce 12 Peru-O. B. Hopkins 12 Trindad-Williaim J. Millard 13 Dutch East Indies-Fred B. Ely 13 Rumania-I. I. Gardescu . .. . 14 India-Eric J. Bradshaw 14

Jan 1, 1931

By W. E. Hale, G. J. S. Govett

An orientation survey was conducted over a known disseminated copper deposit and a Au-Cu vein deposit and employed geological, geophysical, and geochemical methods. Geochemical techniques proved the most effective and economical means of locating and defining areas underlain by these types of mineralization. Six additional, widely separated occurrences were also investigated and mineralization was confirmed by determination of cold-extractable copper in stream sediments. The length of anomalous drainage varies from several to 16 km and depends on the type and tenor of mineralization. Despite generally marked relief and extreme physical and chemical weathering, cold-extractable copper anomalies in soils appear to reflect closely variations in the ore mineral content of immediately underlying rocks. Threshold values vary with local geological conditions and type and grade of mineralization. Significant thresholds in stream sediments are about 65 ppm and 10 ppm for cold-extractable copper in disseminated and vein copper occurrences respectively. Similar differences are encountered in soils. This necessitates the use of a scale of threshold values at progressive stages in each exploration program. Dis-seminated copper occurrences are presently the major source of mineral production m the Philippines. Much potentially productive ground remains to be investigated and applied geochemistry appears to offer the best available approach. The Institute of Applied Geology (I.A.G.), a joint project sponsored by the University of the Philippines, the Philippine Bureau of Mines and the United Nations Development Program (Special Fund) undertook during 1965-66 a number of field projects in Northern Luzon Island (Fig. 1). These field operations were of a two-fold nature and involved both orientation and exploration. During approximately six weeks, an orientation survey, involving geological mapping, geophysical surveying and geochemical prospecting, was conducted over a partly developed, disseminated copper deposit at Santo Nino (Fig. 1). This study demonstrated the economic and technical feasibility of geochemical ptospecting, relative to the other methods tested, for the location and delineation of a typical disseminated copper occurrence characteristic of those that represent the major source of metal in the Philippines.' Geochemical techniques, similar to those tested at Santo Nino, were then applied in a second orientation study of a vein occurrence at Suyoc (Fig. 1). The results of these two orientation studies suggest that, in reconnaissance work in this region, stream sediment analyses, combined with the determination of pH in the same streams, can be used to indicate areas underlain by rock containing anomalous concentrations of copper, whether it occurs in the large tonnage, low grade, disseminated deposits or in the comparatively small tonnage, higher grade, gold vein occurrences. Furthermore, the orientation surveys demonstrate that soil sampling and analysis serve effectively to outline more closely the mineralized zones within the generally anomalous areas identified from the stream reconnaissance. To further test the methods selected from the two earlier trials, six additional, widely separated prospects were investigated. The geological and geochem-

Jan 1, 1970

CONTENTS PAGE MERRISS, M. H.-Direct Electrolysis of Black-copper Anodes of High Nickel-lead Content. Discussed by C. S. Witherell, C. P. Linville, G. E. Dalbey, M. H. Merriss 1 GRISWOLD, GEORGE G.-Calculating the Zinc for Desilverizing Lead Bullion by the Parkes Process. Discussed by C. S. Witherell, George G. Griswold, Milo W. Krejci, Lawrence Addicks, W. F. Gross, H. H. Alexander, A. F. Beasley, C. P. Linville 3 ALEXANDER, H. H. and STACK, J. R.-The Reduction and Refining of Tin in the United States. Discussed by Edward F. Kern, J. R.' Stack, R. L. Hallett, C. R. Hayward, William H. Bassett, R. C. Canby, H. G. S. Anderson 20 GREENAWALT, WILLIAM E.-Greenawalt Electrolytic Copper Extraction Process. Discussed by Stuart Croasdale, Colin G. Fink, Arthur L. Walker, Edward F. Kern, Henry A. Tobelmann, Oliver C. Ralston 26 BENEDICT, C. H. and KENNY, H. C.-Ammonia Leaching of Calumet and Hecla Tailings. Discussed by G. E. Dalbey, C. H. Benedict 34 RALSTON, OLIVER C.-Hydrometallurgy of Lead. Discussed by F. L. Bosqui, Jr., George D. Van Arsdale 34 TAINTON, U. C. and LEYSON, L. T.-Electrolytic Zinc from Complex Ores. Dis¬cussed by W. G. Woolf, C. A. Hansen 39 Direct Electrolysis of Black-copper Anodes of High Nickel-lead Content Discussion of the paper of M. H. MERRISS, presented; at the New York Meeting; February, 1924, and, issued, as Paper No. 1273-M, with MINING AND METALLURGY, September, 1923. C. S. WITHERELL, New- York, N. Y. (written discussion).-This paper is particularly valuable in that it gives the results of operations -carried out under conditions differing from standard practice. In the electrolytic refining of copper, as in other kinds of metal refining, it is occasionally necessary to treat extraordinary foul or complex material, in which cases 'it is valuable to know what other metallurgists have accomplished under similar conditions. As tapping the slimes-covered anodes brought the tank-voltage down to 0.45 to 0.50 volt, the counter electromotive force was, probably not more than 0.1 or 0.2 volt; hence the so-called polarization was, mainly,

Jan 6, 1924

THE Executive Board of The American Engineering Council met in Pittsburgh, May 26 and 27. Its actions on the licensing of engineers and on the Employment Bureau are printed at length elsewhere in this issue. The board announced plans purposing the solution of the national problems of water power and forestry, upon which "the industrial development of the nation and the standard of living of future generations largely depends. The whole Federal water-power situation is in so critical a condition that immediate constructive action by the Government to conserve the public interests, involving vast consequences of economic and Federal policy, is necessary. After a long discussion during which the water-power problem as it affects Government reorganization was reviewed and Henry Ford's Muscle Shoal's plan was discussed, the board decided to lay the entire question before President Harding. A national movement to conserve the nation's forests, in which engineers, the U. S. Forestry Service, the forestry services of the states, universities and technical schools, and other groups such as the farmers, the railroads, and lumbermen, shall pool their efforts, was set in motion by the engineers. The work will be in charge of a Reforestation Committee of the Council, headed by Charles H. MacDowell of Chicago. Mov-ing picture interests will be asked to aid. The board pledged its support to President Harding in his plan for Government reorganization. In adopting the report of its Committee on Public Affairs, headed by J. Parke Channing of New York, the Executive Board of the council determined, in the event of the failure of the President's efforts to bring about greater economy and ffieciency in national affairs by regrouping of Federal functions, to press independ-ently a nation-wide movement for the establishment of a Department of Public Works. Progress in a national survey of the two-shift day in American industries was reported by the Council's Committee on Work Periods in Continuous Industries. This survey, called the most extensive of its kind ever made, has been in progress for more than a year; and purposes an exposition of industrial conditions which shall form a basis for establishing the relative merits of three shifts of eight hours each and two shifts of twelve hours each.

Jan 7, 1922

By H. F. Seifert

THE classification and preparation of non-ferrous scrap metals is a subject of interest to every individual and corporation that employs in its processes of manufacture non-ferrous metals and alloys and accumulates in such manufacture scrap from these materials for disposition in the form .of turnings, borings, short ends, punchings, clippings, grindings, washings, etc. All too frequently the disposition-of such scrap is left to individuals who have no knowledge of the subject either from a metallurgical or a commercial standpoint, or both. Much money is thus lost which with a little more intelligent effort might be saved, and in this day of fierce competition and small profits such an opportunity cannot be ignored. The Mineral Resources of the United States for the year 1925, the latest issue available (Part 1, page 221), gives the secondary non-ferrous TABLE 1.-Some. Secondary Non-ferrous Metals Recovered in the United States for the -Year 1924-25 Material Short Tons Value Copper, including that in alloys other than brass.... 250,600 8 71,170,400 Brass, scrap remelted : 242,300 56,270,800 Lead as metal : 112,420 39,477,100 Lead as alloys 112,460 Zinc as metal 61,430 11,359,000 Zinc in alloys other than brass 13,300 Tin as metal 7,950 Tin in alloys 23,000, 35,165,400 Antimony as metal 1 3,794,000 Antimony in alloys : 10,839 Aluminum as metal 17,700 24,816,000 Aluminum in alloys 26,300 Nickel as metal 191 1,518,000 Nickel in non-ferrous alloys 2,109 Total l 882,600 $243,570,700

Jan 1, 1928

THE LIFE and works of Alexander Agassiz, first president of the Calumet & Hecla Mining Co., were recalled to memory when a monument bearing his statue was unveiled in Agassiz Park, at Calumet, Mich., on Sept. 26, The statue is the work of Paul W. Bartlett, of New York, and was erected by George R. Agassiz, eldest son of Alexander Agassiz. We are indebted to Rodolphe L. Agassiz, now president of the Calumet & Hecla Consolidated, for the accompanying photograph of the statue. The principal address at the unveiling ceremony was delivered by Allen F. Rees, of Houghton, who said, in part: To the world at large Alexander Agassiz was preeminently the man of science. With all his devotion to the industrial life of this district, he found the time to devote to the con-tinuation of his work of scientific research which had been the life work of his fa-ther, Louis Agassiz. Not only did he acquire eminence for his scientific at-tainments and learn-ing, but he was recognized and hon-ored throughout the civilized world for his achievements and accomplishments in the realm of original research. His work in the fields of nat-ural science, in oceanography, in marine zoology, and in other similar lines of research, has added much to our knowledge of the world's mysteries. His life was one of accomplishment also in the industrial world. The union in one life of acknowledged achievement as a scientist and the accomplishment of great results in the prac-tical industrial world is a rare thing, and its possibility has never been exemplified in greater measure than in his life and its results.

Jan 11, 1923

By H. F. Seifert

THE classification and preparation of non-ferrous scrap metals is a subject of interest to every individual and corporation that employs in its processes of manufacture non-ferrous metals and alloys and accumulates in such manufacture scrap from these materials for disposition in the form of turnings, borings, short ends, punchings, clippings, grindings, washings, etc. All too frequently the disposition of such scrap is left to individuals who have no knowledge of the subject either from a metallurgical or a commercial standpoint, or both. Much money is thus lost which with a little more intelligent effort might be saved, and in this day of fierce competition and small profits such an opportunity cannot be ignored. The Mineral Resources of the United States for the year 1925, the latest issue available (Part 1, page 221), gives the secondary non-ferrous TABLE 1.-Some Secondary Non-ferrous Metals Recovered in the United States for the Year 1924-25 Material Short Tons Value Copper, including that in alloys other than brass.... 250,600 $ 71,170,400 Brass, scrap remelted 242,300 56,270,800 Lead as metal 112,4201 39,477,100 Lead as alloys 112,460 Zinc as metal 61,430 11,359,000 Zinc -in alloys other than brass 13,300 Tin as metal 1 7,950 35,165,400 Tin in alloys 23,000 Antimony as metal 1 } 3;794,000 Antimony in alloys 10,839 Aluminum as metal 17,700 24 Aluminum in alloys 26,300 ,816,000 Nickel as metal 19 1 1,518,000 Nickel in non-ferrous alloys 2,109 Total 882,600 $243,570,700

Jan 1, 1928

By C. H. Mahoney, A. L. Tarr, P. E. Le Grand

Magnesium, it is now generally realized, differs in some important aspects from most other structural metals, not excepting even its close neighbors, the aluminum-base alloys. This is particularly true with respect to the effects of elevated temperatures on the two light metals when in the molten state. Aluminum, 0' the one hand, should not be raised above its melting point any higher than is absolutely necessary if one is to avoid danger of gas absorption and a tendency toward grain growth in the resultant casting.' Magnesium alloys, in sharp contrast, actually benefit by being heated to temperatures considerably above their melting point, It is a commonly accepted practice to establish the desired fine grain in the industrial magnesium alloys of the aluminum-hearing group by raising the temperature of the melt after the refining treatment to some 250°C (482°F.) above the melting range. To recall briefly the typical practice for magnesium alloys, the molten metal is refined by fluxing at about 730°C. (I350°F.), and after the melt has been covered with a suitable flux, the temperature is raised to between 870°C. (I600°F.) and 930°C. (1700°F.). It is then cooled as quickly as possible to the casting temperature. This superheating, as it is called, results in a fine-grained cast metal structure which has superior mechanical properties, enhanced amenability to 'solution heat-treatment, and better machinability than cast metal that has not been superheated. The minimum temperature of superheating varies to some extent with the composition of the alloys to be treated and usually increases with the percentage of magnesium in alloys containing the same constituent metals.' It should be noted that the grain-refining effect of superheating is markedly apparent only in connection with the alloys containing aluminum as an alloying Constituent—the binary alloy containing 1.5 per cent manganese, for example, is not refined in grain to any noticeable extent by a superheating effort. While the phenomenon of superheating is well known in the magnesium industry, the mechanism of the process has remained a mystery During the superheating cycle something occurs that forces a fine grain upon the solidifying metal. The process has been controlled in an empirical manner, and occasionally, especially on large-scale melts, and for no apparent cause, no grain refinement is obtained from a superheating treatment. Only a few papers of importance have been published on the subject. Of these, one of the most helpful is the paper by Achenbach, Nipper and Piwowarski,3 which gives considerable data concerning the effect of superheating on various properties such as fluidity, shrinkage and hot crack

Jan 1, 1945

By J. T. Norton, N. J. Grant, I. S., Servi

Coarse grained high purity aluminum was tested in creep at temperatures of 400° to 1200°F to develop subgrain structures. Measurements of subgrain size, distribution, and rotation were made from X-ray diffraction patterns. Subgrain size and distribution were checked metallographically and the size was compared with average slip band spacing. The slip family was determined for several specimens. THE interest and research recently evident abroad in the role of subgrain formation and polygon-ization as a contribution to the creep of metals at elevated temperatures is deserving of greater attention in this country. Such metallic subgrains can be defined as macroblocks existing within the grains. The general observation has been that the macro-blocks which belong to the same grain have a maximum difference in orientation of a few degrees. In spite of the considerable amount of work that has been done since Jenkins and Mellorl observed the "division of existing crystals into smaller units when deformation occurs at an annealing temperature," the subject of subgrain formation is only now receiving truly active discussion and investigation. The existence of subgrains has been revealed by metallographic methods, as in the work of Jenkins and Mellor,1 and by X-ray methods, first applied to this problem by Homes.' Hirst3 and Calnan and Burns4 applied the back-reflection Laue technique to the study of coarse grained specimens. Wood et al.5 and Greenough and Smith' examined the ring obtained with a back-reflection camera for the study of fine grained specimens. In addition to the above, the transmission technique was used by Wood.6 A special technique was developed by Guinier and Tennevin8 in order to improve the resolution. Metallographically, the subgrains have been observed directly on the surface of deformed specimens by Wood et al.,3 or have been made evident on repolished surfaces by applying a suitable etching reagent. The latter technique, first suggested by Lacombe and Beaujard,9 was then improved by Wyon and Crussard.10 Subgrains can be formed in single crystals after small amounts of bending followed by heating after this cold work, or during deformation at elevated temperatures. The first phenomenon was analyzed by Cahn11 for the simple case of pure bending followed by annealing. Cahn suggested a mechanism of subgrain formation based on the dislocation theory and called this phenomenon "polygonization." He extended this mechanism to the more complex case of local bending, such as the bending which may occur when a polycrystalline specimen is deformed in tension. Cahn's suggestion was later found quite consistent with the results obtained by Dunn and Daniels." An explanation has been presented recently regarding the formation of subgrains during deformation at elevated temperatures by Chang and Grant.'" In general, there are two schools of thought on the subject. One, according to Wood et al.,5 is that subgrain formation is a mechanism of deformation which is operative under certain conditions in the same way that the slip process is the mechanism of deformation which is operative under other conditions. The boundaries between the subgrains undergo a viscous flow which contributes substantially to the deformation of the material. The second, according to Cahn,13 Wyon and Crussard,10 and Chang and Grant,18 is that subgrain formation is the effect of simultaneous deformation and annealing and is,

Jan 1, 1953