Search Documents

By Leo Ranney

ANY years ago a prospector came to a Nevada town and built himself a shack. Day after day he searched the hills for gold -but he found none. He closed his shack and hurried north, where a strike had been made. Next he tried to trap the flour gold that floats down the Snake River. He panned the black sands along the Oregon coast. He ranged over the mountains and up the gulches of far-off Alaska. At last, broken in health, six years ago he came back to his old home in Nevada. There his shack still stood-nobody wanted it. One day he started a garden in the rocky soil that he owned. His spade turned up a chunk of quartz, and in that quartz were stringers of gold. He had found a rich gold vein, running right under his own house. You gas producers who have hurried to Oklahoma, Louisiana, East Texas, South Texas, West Texas, even to California to drill wildcat holes a mile or two miles deep-why not, like the old gold prospector, have a look in your own back yard? Some of your coal seams contain 20,000,000 cu. ft. of natural gas per acre.

Jan 1, 1943

By W. Smith, F. G. Rinker, D. Beggs

Early in 1965 the Surface Combustion Division of the Midland-Ross Corporation was awarded the contract to engineer and construct a taconite pelletizing plant for the National Steel pellet plant, administered by the Hanna Mining Co., near Keewatin, Minn. This plant, which will have an annual capacity of 2,400,000 long tons, will produce pellets from magnetite concentrate using a new process developed through a joint research program by Midland-Ross, Hanna Mining, and the National Steel Corp. The work that culminated in the decision to construct this plant is the result of a research program for the development of the Midland-Ross heat fast process for the production of prereduced or metallized pellets. PELLETIZING PROCESS There are many acceptable methods for producing oxide pellets from ground iron ores and concentrates, and all of these give an acceptable product for blast furnace utilization. The vertical shaft furnace, the traveling grate, and the grate-kiln have been installed in many pelletizing plants in the northern hemisphere; therefore, the acceptance of these methods and the problems associated with them are well understood. However, this research project investigated a method for improving upon these processes to produce a high quality oxide pellet at a low operating cost.

Jan 9, 1966

By P. Davey Wheeler

San Francisco meeting, September, 1915) IN an article in the General Electric Review, January, 1915, reference was made to the X-ray examination of a steel casting 9/16 in. thick. Fig. 1 shows one of the radiographs thus obtained. All these radiographs showed plainly the tool marks on the surface of the casting. All but one showed peculiar markings the shape of which strongly suggested that they were indeed the pictures of holes in the interior. A circular piece, 1 in. in diameter, was punched from the casting at a point where the radiograph shown in Fig. 1 indicated that a blow-hole should be found. (Location of sample shown by circle in Fig. 1.) Fig. 2 is a photograph of the end of the punching, showing the .hole that was found. Since that article was written it has seemed desirable: (1) to obtain data from which the exposure necessary for any thickness of steel could be at once calculated; (2) to find the thickness of the smallest air inclusion which could be radiographed in a given thickness of steel; (3) to determine in what direction to hope for further progress; and (4) to develop the technique of, radiographing metals. In order to gain some preliminary data, several pieces of ½ -in(12.5mm.) boiler plate were obtained, 5 by 7 in. (12.5 by 17.5 cm.) in size. In one of these, holes were drilled in such a way that the axis of each hole was midway between the faces of the steel and parallel to those faces. The diameters of these holes were as follows: Hole number Diameter 1 1/4 in. = 6.3 mm 2 1/8 in. = 3.1 mm. 3 1/16 in. = 1.6 mm. 4 1/32 in. = 0.8 mm. 5 1/64 in. = 0.4 mm.

Jan 8, 1915

By AIME AIME

MOST of the copper mines in Canada are favored by nature in having other metals besides, copper in their ore, which puts them in a most satisfactory competitive position. Noranda ore has an important gold content, Flin Flon gold and zinc, and International Nickel of course has nickel. All of the larger copper companies in Canada operated during 1.933 and the total production of copper exceeded that of the year before. The Britannia Mining and Smelting Co. worked out to succcessful conclusion a three-product flotation process for separating the copper, zinc and iron from its low-grade ore. Although the method and equipment is different from that used at the Flin Flon mine, the object is the same, that

Jan 1, 1934

TULSA SECTION At the smoker concluding the two day meeting of the Tulsa section of the American Institute of Mining and Metallurgical Engineers, Tulsa, Okla., Feb. 26, 1919, Dr. Willis T. Lee, the new head of the Geological Department of the University of Oklahoma, was introduced to the assembled geologists and mining engineers. Dr. Lee requested that the geologists and engineers who were making a specialty of petroleum geology assist him in giving a good course in practical oil geology in the Geological Department of the University. After a motion offering the services of all present in giving lectures on their special subjects had been adopted, Dr. Perrine of Hutchinson, Kans., named the geologists who were pledged to give lectures in Dr. Lee's course. The students in geology at Norman are assured of the latest information regarding practical work in petroleum geology and will have the inspiration derived from contact with men who are actually at work upon the problems which they are studying. Dr. Lee and President Brooks of the University are to be congratulated upon the introduction of this .method of instruction. The plan thus put into operation is similar to the graduate system of coaching in athletics followed at many of the large universities; what is good for instruction in athletics should also prove good for instruction in applied geology.

Jan 6, 1919

By D. W. Fuerstenau

On page 1243, column 1, the first line of the author's reply should read "D. W. Fuerstenau (author's reply)---," rather than D. E., as printed. In the sentence immediately preceding the first equation (page 1243, column 2)' the word "none" was omitted. The sentence should read: "However, if enough ore is put into the mill [so] that none of the energy put into the mill is wasted on metal-to-metal impact, then the product should have size modulus determined by the relation: ..."

Jan 1, 1961

By Wayne Loel

The application of aerial photographs to all phases of geologic mapping is set forth, indicating the advantages to be gained in different types of country and undcr varying climatic conditions. Methods of field and office procedure are given from a geological point of view, as well as suggestions regarding the best methods of aerial mapping for different uses and under varying field conditions, including the study of submarinc geology. Aerial photographs with accompanying geologic maps are shown to illustrate the appearance from the air of different geologic features under varying climatic and topographic conditions. Introduction The following paper is in no sense a contribution to knowledge; it is merely an attempt to indicate some of the benefits that may be expected from the use of aerial photographs in geologic mapping and to mention some inherent limitations. The writer has used aerial photographs in his own work for the past 13 years and has had ample opportunity to observe their use in the hands of others. From this experience certain conclusions have been drawn, which may be helpful to those using aerial photographs for the first time. It must he remembered that a photograph of the earth's surface can delineate only that which the eye can see; therefore the geologist should not expect more from an aerial photograph than he would be able to observe were he in the photographer's airplane looking at the area to be photographed. Theoretically, if the geologist had sufficient artistic ability, he could draw as good a geologic map from his position in the plane as he could from observation of the photograph. Practically this cannot be done because the airplane moves at a high rate of speed, which in itself prohibits detailed observation and, no matter how great the geologist's artistic ability, he could not reproduce the detail that can be recorded by a camera. An aerial photograph is a picture map of an area. The picture may be studied in the office until the geologist is thoroughly familiar with every minute detail of the surface of the ground he is about to geologize. If it is an area, underlain by sedimentary rocks, much may be learned

Jan 1, 1941

By Wayne Loel

The application of aerial photographs to all phases of geologic mapping is set forth, indicating the advantages to be gained in different types of country and undcr varying climatic conditions. Methods of field and office procedure are given from a geological point of view, as well as suggestions regarding the best methods of aerial mapping for different uses and under varying field conditions, including the study of submarinc geology. Aerial photographs with accompanying geologic maps are shown to illustrate the appearance from the air of different geologic features under varying climatic and topographic conditions. Introduction The following paper is in no sense a contribution to knowledge; it is merely an attempt to indicate some of the benefits that may be expected from the use of aerial photographs in geologic mapping and to mention some inherent limitations. The writer has used aerial photographs in his own work for the past 13 years and has had ample opportunity to observe their use in the hands of others. From this experience certain conclusions have been drawn, which may be helpful to those using aerial photographs for the first time. It must he remembered that a photograph of the earth's surface can delineate only that which the eye can see; therefore the geologist should not expect more from an aerial photograph than he would be able to observe were he in the photographer's airplane looking at the area to be photographed. Theoretically, if the geologist had sufficient artistic ability, he could draw as good a geologic map from his position in the plane as he could from observation of the photograph. Practically this cannot be done because the airplane moves at a high rate of speed, which in itself prohibits detailed observation and, no matter how great the geologist's artistic ability, he could not reproduce the detail that can be recorded by a camera. An aerial photograph is a picture map of an area. The picture may be studied in the office until the geologist is thoroughly familiar with every minute detail of the surface of the ground he is about to geologize. If it is an area, underlain by sedimentary rocks, much may be learned

Jan 1, 1941

By WM. E. Mlligan

IN the last year, much information had become available as to the extent that zinc participated in the war effort. The importance of foreign zinc in this program had been indicated by Bateman (M&M April 1945) as of the order of 400,000 tons annually in zinc or contained zinc. Pehrson (M&M April 1945) reviewed the domestic ore-reserve situation with respect to most minerals and metals and showed the extent to which commercial zinc ores had become depleted in this country. This picture was further darkened by O.P.A. figures appearing in E.&M.J. July 1945 in which figures for total production during the three previous years were broken down into percentages produced under ceiling and various quota price categories. True, factors other than depleted ore reserves contributed to this picture. Among the more important of these, were shortage and high cost of labor, both skilled and unskilled, and the general difficulty and cost of maintaining adequate equipment and supplies. The cost of production in the Tri-State district was most affected.

Jan 1, 1946

Two sessions during the recent AMC Mining Convention in Los Angeles, September 23-26, served to update industry personnel on the status of health and safety regulations in the US. As reflected by the American Mining Congress resolution on mine safety and health, "Based on experience with the federal Coal Mine Health and Safety Act of 1969 and the federal Mine Safety and Health Act of 1977, (AMC) does not believe that laws designed to force compliance with regulations through the imposition of criminal or civil penalties will result in safer mines. (AMC) feels that the government's participation will be much more productive if greater emphasis is placed on research, training, and inspections aimed primarily at assisting operators and employees in recognizing and eliminating hazardous conditions and practices.

Jan 11, 1979

By Claude P. Heiner

While the title of this paper embraces the entire West Coast, the author, in the interest of simplification. has confined the discussion to California-particularly the central section. California's population has, risen 45 pct since 1940. Its electric requirements have also increased, not only because of the growth in industry and population but also because of the widespread tendency of all types of electric consumers to use more electricity than ever before. The growth of California's electric utilities is shown by published data covering operations, of three of its large systems and is given in Table 1.

Jan 1, 1949

Edward A. UehlinG, New York City (communication to the Secretary*):—Mr. Baker's paper is one that brings up a subject of great importance, and if full statistics could be collectecl of the number of furnace-linings ruined by reason of bad distribution by skip-hoists, it would be found an astonishing array. Unfortunately a universal remedy has not yet been found. The fact that Mr. Baker has apparently succeeded in overcoming the trouble at Sydney, is no guarantee that the same remedy applied at another plant, where very different or even slightly different conditions prevail, mould cure the trouble. That it requires but a slight continuous difference of penetrability in the column of the descending stock of one section, over another, to produce channeling, is clearly demonstrated by Mr. Baker's experiments, by which he reversed the channeling from front to rear instead of remedying the trouble. Every change in the physical make-up of the charge necessarily requires a specific adjustment; even supposing this feasible, the regular working of the furnace is by no means assured, because with the high pressures now customary, the tendency of the ascending gases to plow their way through in a direct course, prevails, and having once opened up a passage, they will persist and cause trouble. Homogeneous filling-, hard driving and regularity of working are incompatible. The higher the furnace, the greater the

Jan 1, 1905

By AIME AIME

THE Federated American Engineering Societies through its Executive Board has endorsed House Bill 5230, introduced April 26, 1921, which provides for- the completion of the topographical survey of the United States. Before this bill can be reported out it will be necessary for the House Committee on -interstate and foreign commerce to hold hearings. This will not be done unless the engineers of the country show interest -and demand action which should be taken immediately after the recess ends and Congress reconvenes this fall. Surveys and maps have been made in this country ever since Captain John Smith mapped Chesapeake Bay about. 300 years ago, but it is only in comparatively recent years that the need for accurate maps has been keenly felt by those engaged in the industrial' and commercial development of the country.

Jan 1, 1921

By John H. Bassarear, A. A. Dor

INTRODUCTION Primary grinding mills as defined in this paper, are autogenous or semi-autogenous rotating, tumbling mills having a coarse feed with a top size usually varying from 150 to 300 mm (6 to 12 inches). Most frequently, the feed to these mills is the product of primary crushing plants but in some cases run of mine ore is used as feed such as at Benguet, McDermitt, L-Bar Sohio, Bear Creek and others. The size of the largest lumps in the mill feed is principally determined by limits set by the mill feed trunnion diameter and by the type and size of conveying equipment used for handling and of bins and stockpiles used for storage. The use of primary mills in mineral processing plants has expanded very significantly in the last twenty years, and they have been successfully applied to the treatment of a wide variety of ores in both wet and dry grinding applications. In the present state of technological development for primary grinding mills, there is a wide choice of acceptable options with respect to type and size, grinding flowsheet and grinding media. The choice of the optimum combination which would result in the most satisfactory condition of operation, from the standpoint of both metallurgical results and costs, depends on the nature of the ore, the required characteristics of the grinding products and on various geographic and economic circumstances. The effects of such factors and considerations on the choice and sizing of primary grinding mills and flowsheets are reviewed and discussed in the following pages. PRIMARY MILLS SELECTION Inherent Characteristics of Primary Grinding Primary grinding is complex because it involves several comminution mechanisms which occur simultaneously and to some degree interfere with one another. These mechanisms of impact, attrition and abrasion have been described earlier. The relative importance of these three main grinding actions and their mutual balance resulting in a continuous uniform operation of the mill depend to a very large extent on the nature of the ore and its physical properties. Homogenous, single mineral ores will behave quite differently from heterogenous ores consisting of different minerals bound together along defined

Jan 1, 1982

By Howard N. Eavenson

AN analysis of the bituminous coal situation by an authority who traces the production, mining, safety, markets and labor trends in comparison with other fuels. BEFORE 1918 the production of coal experienced a steady growth, with slight recessions in ouput in only twelve years (1837, 1841, 1852, 1855, 1861, 1874, 1876, 1889, 1894, 1905, 1909, 1914), and in each of these cases the loss was recovered in the following year and the increase continued. In each decade the output was doubled. Prices, while not high, allowed some profit. In 1918 during World War I, an output of 580 million tons was reached and with the exception of 1923 this total was not again reached until 1942, in World War 11. Losses of output in this period were much greater than ever before; in 1932 the total was 270 million tons less than in 1918 or 1923, and the loss after 1923 was not recovered until 1942. The greatest output was 631 million tons in 1947.

Jan 1, 1950

By N. Tiner

The mechanical properties of magnesium-alloy castings are greatly improved by grain refinement, and at present considerable attention is being paid to methods of obtaining fine-grained castings. One method of achieving this end is the use of proper melting and superheating techniques. These have been employed com-rnercially to a great extent, but no comprehensive study of the subject appears to have been published at present. Numerous investigations found in the literature include some reference to superheating techniques,1"4 and Achenbach, Nippcr and Piwowarsky,% ased principally on thermal analysis, ascribe the grain-refilling action of superheating to the influence of solid foreign particles or dissolved gases present in the melt upon the course of crystallization. The primary purpose of this paper is to present the principal facts concerning the cffect of superheating on grain size of magilesium alloys. .ittempts are also made to explain the experimental results in terms of a general hypothesis. The investigations are limited chiefly to common commercial casting alloys. In order to carry on this work, it was necessary to determine the factors influencing grain size and to develop a proper technique for the preparation of samples. Thc preliminary tests made by the author indicated that the grain size of magnesium alloys resulting from the solidification of a melt is determined by alloy composition, presence of impurities, rate of cooling during solidification, thermal history of the melt and to some extent the structure of the charge used. The rate of cooling is in turn dependent upon the mass of the melt, pouring temperature, and dimensions, properties and temperature of the mold into which the melt is poured. The final grain size of the alloys is still further modified by heat-treatment subsequent to casting. It is not within the scope of the present paper to discuss all of these factors, and it would suffice to note here that when equal amounts of magnesium alloys are prepared from the same alloying materials, melted in graphite crucibles under the same thermal conditions, then cast into graphite molds at a constant temperature, the resultant solids have the same grain size. By maintaining all other factors constant, it is thus possible to vary thermal conditions of a melt and to examine the grain size of resultant castings. Preparation of Samples and Grain-size TestiNg The alloys investigated in this paper were taken from ingots made by Permanente the Or or prepared by the author with pure carbothermic magnesium and necessary alloying elements. Melting was carried out under a flux in a graphite crucible heated uniformly by an

Jan 1, 1946

By N. Tiner

The mechanical properties of magnesium-alloy castings are greatly improved by grain refinement, and at present considerable attention is being paid to methods of obtaining fine-grained castings. One method of achieving this end is the use of proper melting and superheating techniques. These have been employed com-rnercially to a great extent, but no comprehensive study of the subject appears to have been published at present. Numerous investigations found in the literature include some reference to superheating techniques,1"4 and Achenbach, Nippcr and Piwowarsky,% ased principally on thermal analysis, ascribe the grain-refilling action of superheating to the influence of solid foreign particles or dissolved gases present in the melt upon the course of crystallization. The primary purpose of this paper is to present the principal facts concerning the cffect of superheating on grain size of magilesium alloys. .ittempts are also made to explain the experimental results in terms of a general hypothesis. The investigations are limited chiefly to common commercial casting alloys. In order to carry on this work, it was necessary to determine the factors influencing grain size and to develop a proper technique for the preparation of samples. Thc preliminary tests made by the author indicated that the grain size of magnesium alloys resulting from the solidification of a melt is determined by alloy composition, presence of impurities, rate of cooling during solidification, thermal history of the melt and to some extent the structure of the charge used. The rate of cooling is in turn dependent upon the mass of the melt, pouring temperature, and dimensions, properties and temperature of the mold into which the melt is poured. The final grain size of the alloys is still further modified by heat-treatment subsequent to casting. It is not within the scope of the present paper to discuss all of these factors, and it would suffice to note here that when equal amounts of magnesium alloys are prepared from the same alloying materials, melted in graphite crucibles under the same thermal conditions, then cast into graphite molds at a constant temperature, the resultant solids have the same grain size. By maintaining all other factors constant, it is thus possible to vary thermal conditions of a melt and to examine the grain size of resultant castings. Preparation of Samples and Grain-size TestiNg The alloys investigated in this paper were taken from ingots made by Permanente the Or or prepared by the author with pure carbothermic magnesium and necessary alloying elements. Melting was carried out under a flux in a graphite crucible heated uniformly by an

Jan 1, 1946

By J. Clair, H. Mirabel

The determination of the temperature and electrical potential distributicms in the cathodes of aluminum electrolytic cells is difficult. The reascms come from the various nature and the intricate three-dimensional geometry of the materials; besides thermal and electrical phenomena react upon each other. A method of calculation using a computer program applied to a mathematical model, figuring the cathode, is developed. Both of the thermal and electrical phenomena are simultaneously considered. Temperature and electrical potential distributions are finally obtained by successive iterations. Results are compared with measurements on industrial cells. Theoretical and practical applications of these studies are given. Up to the present time the study of the distribution of the temperatures and electric potentials in the electrodes, anode and cathode, of the electrolytic cells used for the production of aluminum was limited to one of the two aspects of the phenomena because of lack of a simultaneous method of calculation. For example, the anode or cathode drop was studied assuming that the temperatures in the iron and carbon are known, a method that obviously is very approximate since iron resistivity, in particular, greatly varies with temperature, which in turn depends on current density. Consequently we tried to find a method of calculation simultaneously taking into account both thermal and electrical phenomena. We proceeded to the study of the cathodes as an initial approach to the problem. Although the cathode and surrounding materials may have varied forms and particularly very heterogeneous characteristics, their structures are simpler than that of the Sijderberg anode and boundary conditions are more easily represented than in the case of anodes even though they are prebaked. The study was in two parts: a) development of a model schematizing the true geometry of a cathode and defining the thermal and electrical boundary conditions, and b) working out a method of calculation of the temperatures and potentials by means of an electronic computer. To facilitate solution of the problem, a model was used initially much simplified in comparison with an actual cathode. This model permitted development of the method of calculation. In a second phase, this model was adjusted to the study of actual cathodes and applied to different types of cells: low- or high-intensity cells, cells set up at ground level or above ground level, cells with cathodes more or less heat-insulated. Simultaneously measurements were made with cells equipped with cathodes of the types studied to compare the values resulting from calculation. The initial model was also used for general studies, in particular for studying the effects of current density in the carbon and iron. The results were confirmed or made precise by the model of the true cathodes. This report successively describes: a) the manner in which the model representing a cathode was worked out, with the simplifications and/or the hypotheses used, b) the method of solution of the problem by means of the electronic computer, and c) an example, stating the extent to which the results obtained may be realistic. Further the possibilities offered by such a study are examined. 1) CATHODE REPRESENTATION The purpose of this phase is to represent the cathode in the form of a so-called "mathematical model", that is with a simplified geometrical configuration, in order to meet the subsequent calculation requirements, while keeping to the true facts as closely as possible. This model further includes the thermal and electric conductivities with regard to temperature for the varied materials composing the cathode, as well as the thermal and electrical conditions at the model boundaries. 1.1) Guiding Principles. For calculating the temperatures and potentials the model is divided by trior-thogonal planes into a network of small elementary parallelepipeds. At the summit of these parallelepipeds' so-called mesh points, the temperatures and potentials are computed. The number of mesh points is of course limited by the capabilities of the computer, since 1) the number of equations to be solved depends on the number of mesh points selected, and 2) the amount of time spent by the computer considerably increases with increasing this number. These conditions call for the following requirements as concerns the model: a) Dimensional requirements: the calculation will be all the more accurate as the network is more closely meshed. Since the number of mesh points is limited in practice, it is necessary to restrict the dimensions of the model. b) Geometrical requirements: so as to make things easier in working out the network, the model must be given a simple geometry. In particular, it will be convenient to have the cathode so constituted that the surfaces limiting the cathode and the surfaces within the cathodes separating the different materials consist of triorthogonal planes. 1.2) Schematization of the Cathodes. After the tech-

Jan 1, 1968

By C. K. Leith

OTHERS here are far better qualified than I to discuss some of the specific proposals for government regulation of the oil industry. I shall make no attempt to carry oil to Oklahoma. The question of public control, however, is inherent in other branches of the mineral industry in varying degrees, and my comments will be directed mainly toward some of the trends affecting the mineral industry as a whole, as a background for your more specific consideration of oil legislation. A proud American tradition has been the insistence on freedom of competition, on equality of economic opportunity, on a policy of laissez faire. Nowhere has this principle been given wider application than in the mineral industry. The mineral field has been open to all comers, and the job of mineral exploitation has naturally attracted daring and independent spirits. The laws governing conditions of discovery and development, as well as the anti- trust laws, have been devised to foster the spirit of private initiative. The result has been the building of a mineral industry on a scale never before approximated anywhere in the world. The impetus thus gained, the methods, the technique, the financial resources, have been projected be- yond our boundaries and have made the American mineral industry the purveyor to the world for many essential commodities and first in the exploitation of the world's minerals. Our habits of individual self-reliance and success are deeply ingrained, and there is hardly an individual in the entire mineral field who does not instinctively recoil fro111 the extension of collective control, whether public or private.

Jan 1, 1932

By HUGH E. McKinstry

OPENING the sessions of the Mining Geology Committee, the program on postwar mineral controls drew a larger attendance than any other session of the entire meeting. In view of its general interest, the papers of this session, or a substantial portion of them, are printed elsewhere in this issue. Whether control of mineral resources can help to promote peace, how controls could be applied and to whom, are questions so far-reaching that naturally no pat answer was agreed upon. In fact the discussion took on something of the flavor of a debate between those who favor strict control and those who felt that attempting to ration nations in peacetime would defeat its own ends. Discussion from the floor emphasized the difficulties in administering any international control and the $64 question, that no one cared to answer, asked by a courageous young lady who was induced to mount the rostrum for the purpose, was whether the United Nations should exchange mineral controllers to police each other.

Jan 1, 1944