Search Documents

By Stig O. Olofsson

The problem of overbreak in underground construction and mining is normally approached by a variety of smooth blasting methods. Numerous small diameter, low velocity explosives have been developed specifically for blasting the contour line. Increased mechanization in rock excavation has led to the development of several methods of mechanical explosive loading. A new mechanically loaded smooth blasting explosive was developed in Sweden . However, several limitations were realised, which after several trials resulted in a hybrid smooth blasting method, The Suaer Cautious Contour Blasting Method which will be discussed in this paper.

Jan 1, 1994

By Alain Blouin, Mohamad Sabsabi, Aissa Harhira, Paul Bouchard, Greg Lithgow

"The objective of this study was to demonstrate the application of Laser-Induced Breakdown Spectroscopy (LIBS) to the continuous analysis of online monitoring of Al, Mg, Ni, Mn, Si and Fe in nickel ore limonite and saprolite slurry samples. Analysis was performed on slurry samples in air at atmospheric pressure. Two pure samples of limonite and saprolite were used. Mixtures of the two samples in varying proportions were used to build calibration curves, study the influence of solid/liquid ratio, and evaluate short and long term reproducibility. The LIBS measurement of these elements is independent of the water content (from 70-85%, the range allowed by our setup). Repeatability of the measurement and long term reproducibility (from day-to-day) were below 1.2 % and 2% respectively for all the elements studied in our conditions. The results obtained showed that an industrial LIBS analyzer could provide the chemical composition of the six elements Al, Mg, Ni, Mn, Si and Fe within 1-2 minutes.IntroductionThe metal-producing industry faces the major challenge of increasing productivity, reducing costs, and maximizing benefits from existing equipment. By pyrometallurgy, metal making involves the basic steps of charging the furnace, melting the charge and refining. By hydrometallurgy, the metal refining is carried out through the dissolution of the metal by chemical reaction and electrolysis. During refining either by pyrometallurgy or hydrometallurgy, it is critical that operating parameters be adjusted and controlled so that the chemistry of the melt or the solution is within predetermined limits. Presently, the complete turnaround time for sampling, sample transfer, analysis and communication of the results to the operators is often 30 minutes or more."

Jan 1, 2016

By Tatsunori Matsumoto

In order to investigate the variation of the load-displacement relations of piles in a site, vertical load tests were carried out on 25 small diameter steel pipe piles. Out of 25 piles, 15 piles were close-ended pipe piles attached with a blade at the pile toe and 10 piles were open-ended pipe piles. To carry out these load tests in a short period, two types of rapid load test methods, Spring hammer load test and Falling mass load test, were employed. The load tests of all piles were completed in two days with 180 blows in total. In order to estimate a static load-displacement of a pile, non-linear damping method was used. It is shown from the test results that the performance of the pipe piles such as the ultimate pile resistance and the initial pile head stiffness is improved by re-driving.

Jan 1, 2006

By John G. Henning

The Porcupine Joint Venture operates the Dome Mine in South Porcupine, Ontario. Dome underground began production in 1910. It is the longest continuous operating gold mine in Canada, producing in excess of 15 M ounces. More than 900 underground stopes have been mined and hundreds of miles of drifts, sublevels and raises developed. Underground mining methods included shrinkage, cut and fill and longhole. Not all stopes were backfilled upon completion, particularly the longhole stopes. The Dome open pit was designed above the underground mine workings such that, as the pit is excavated, it intersects underground drifts and stopes. Potential operational problems associated with the interactions between the stopes and the pit walls may occur, necessitating pit wall redesign, ground support installation and operational rescheduling. Each intersection of the pit with the underground mine workings is closely evaluated to maintain a safe working environment and wall stability. This paper discussed how risks to pit wall stability are assessed, mitigated and monitored.

May 1, 2004

By Hu Harries

WE RECENTLY completed a study for a client, who is an applicant to export gas from the Province of Alberta, on the effects of gas export on Alberta's economy. This study was part of the client's application ?before the Conservation Board, and, no doubt, some of you are familiar with it. Submissions by other applicants in earlier hearings before the Board and before the Royal Commission on Energy, as well as claims made by parties opposing export, have also brought forward a number of other opmwns regarding possible economic effects. Ali of these studies have been on a piecemeal basis. They have dealt with particular aspects of particular applications, and only indirectly and by inference with the overall question of gas ex-port. We have prepared this paper to review the overall picture and ex-amine, as far as time permits, all sides of the question. While the paper is entitled Economic Effects of Gas Export on Alberta, we felt that the area considered should in-elude northeastern British Columbia, not only because Westcoast, the first major gas export project, is essentially a northeastern B. C. project, but because this area has historically been, from the point of view of economic, if not of political, geography, part of Alberta. In this paper, when we talk of export, we mean export from the Province or, in this case, from Alberta plus northeastern B. C. Sales to other parts of Canada have exactly the same effect on the economy of this area as l1ave sales to the United States, provided, of course, they are made on equal terms.

Jan 1, 1958

By Craig C. Johnson

The purpose of this effort was to investigate the feasibility of employing a piezoelectric transducer for seismic communications applications in mine environments. The transducer, a government furnished device incorporated a high Q, spring-mass resonator to load the air side of the piezoelectric crystal. The resonant frequency was seismic load dependent and fell in the range of 300 to 340 Hz. The effort included a mathematical analysis of the transducer, with corroborative laboratory tests, together with actual communications experiments performed first in an open-formation limestone quarry and finally in an operating iron mine. This work showed that the transducer could be coupled efficiently to hard, competent rock media with power conversion efficiencies of 70 to 80 percent (electrical to mechanical) in typical installations. In the iron mine, when radiating peak power was about 30 W (acoustical) in a gated pulse mode, signals were received at a distance of 760 ft through a massive rhyolite porphyry formation. This represents a 15% radiation efficiency with an input of 200 watts. Despite the high ambient noise level due to operating mine machinery, a signal-to-noise ratio of about 20 dB was achieved using a very narrow band filter to process the received signal, and a data rate of about two pulses/sec was demonstrated.

Jan 1, 1972

By N Pranoto, E Lawell, T Dean, M Grant

The Goonyella Riverside Mine is located 30 km north of Moranbah in Central Queensland, Australia. Recent mining activities have exposed the north–south striking Kenya and Zimbabwe thrust Faults. These faults vertically offset coal seams by up to 25 m and locally thicken coal packages through imbrication of coal seams. The presence of back-thrusts add to the geotechnical complexity of maintaining highwall stability. The Kenya and Zimbabwe Faults have provided multiple challenges to the mining operation, with an unplanned additional 240 kt of coal tonnes being mined from imbrication of coals seams or from the refinement to local scale geological models. These additional coal tonnes have been either identified during the mining of the coal seam or just prior to overburden removal above the coal seam. These faults can also negatively impacted highwall stability with highwall failures, lowering the overall slope angle for pit designs and increasing stand-off distances for hazardous highwall conditions. Unmanned Aerial Vehicles are used to scan exposed highwalls and enable geological mapping via high-quality 3D images. Measure while drill data from drill and blast rigs can provide local-scale intersections of the faults and coal seams. Mine Geologists utilise these and other data sets to create localised geological models refined position of the fault planes and coal seams. These models are utilised by relevant mine site teams to ensure the safe and efficient mining of coal around these faults.

Mar 22, 2022

By Lars Skogsberg

Work with hand-held power tools can be found in most industries all over the world. This type of work exposes the operators to different kind of loads like gripping-forces, feed-forces, exposure to vibration and noise, holding hot or cold surfaces and the exposure to dust. Designing a power tool with good ergonomics is a matter of finding the best compromise. As a simple example, increasing the mass is not acceptable because it will increase the forces needed to handle the tool. At the same time increased mass will in most cases reduce the vibrations. Vibration disorders related to the use of hand-held power tools has been known and reported since long. It is therefore essential that low vibrating tools are developed and used. The new vibration regulations in Europe, based on the Physical Agents (Vibration) Directive, have put increased focus on the vibration control in industry. Forces acting on the tool cause vibration Tools for industrial use must be of very robust design to withstand the very hard use they are exposed to. Industrial tools are therefore normally designed with the main parts made of metal. From a vibration point of view this means that most tools can be regarded as rigid bodies, especially because the dominating frequency normally is equal to the rotational frequency of the tool spindle or the blow frequency for a percussive tool. These frequencies are with few exceptions below 200 Hz. Handles however can not always be regarded as rigidly connected to the tool. There are several examples of weak suspensions designed to reduce vibration transmitted to the hands of the operator. There are also examples of designs where the handles just happened to be non-rigidly connected and in some cases even in resonance within the frequency region of interest. Oscillating forces act on the tool and the result is vibration. Design principals In all cases forces are the source of vibration. This leads to the three basic principles to control vibration: • Control the magnitude of the vibrating forces. Examples are the balancing unit on a grinder or the differential piston in a chipping hammer. • Make the tool less sensitive to the vibrating forces. Examples can be when the mass of the guard on a grinder is rigidly connected to the tool to increase the inertia of the tool. • Isolate the vibrations in the tool from the grip surfaces. Examples are vibration-dampening handles on grinders or pavement breakers, the air-spring behind the blow-mechanism in a riveting hammer or the mass spring system in a chipping hammer.

Jan 6, 2006

By L. D. Keller

The application of hydraulic concentration to large scale operations has been effectively accomplished by the use of the SiphonSizer. Operation has been simple, automatic and essentially trouble free. The use of the primary desliming SiphonSizer on magnetic taconites has shown an improvement in grade of concentrate and an increase in recovery over conventional hydroseparators. Magnetic concentrates have been further deslimed and upgraded in SiphonSizers by floating a coarse middling product away from the heavier concentrate. The application of the Siphon-sizer to closed circuit grinding has met with only partial success to date. Hydraulic concentration of minerals has been practiced for a good many years. Until recently, however, the practice has been limited to equipment using a multiplicity of small pockets and relatively low tonnages and flows. The adaptation of the SiphonSizer to the concentration and classification of magnetite has changed this concept. Some fifty commercial units varying in size from a 16-ft diam circular unit to a 25x100-ft rectangular unit are currently in operation on magnetic taconites. Additional units up to 38 ft diam are under construction. Depending upon the application in the flowsheet, upgrading varies from 0.75% to 14% Fe in a single stage. To those not familiar with taconite processing, the importance of the struggle to remove economically as much silica as possible may not be fully appreciated. Perhaps some figures pertaining to transportation costs will underscore this important process. If the silica content of the concentrate from a 10,000,000 ton per year plant could be reduced by I%, a savings in boat freight, at $2.00 per ton, would amount to $200,000 annually! THE SlPHONSlZER The SiphonSizer, as illustrated in Figs. lA, 1B and 2, is a hydraulic classifier in which the hydraulic water is distributed uniformly across the bottom of the vessel by means of a system of headers (1 and 2), jet pipes (3), and nozzles (4). The depth of the teeter bed is automatically maintained by the siphon-float assembly. The feed is introduced through a feed well (5) and separated into two fractions by the effects of rising water and the density of the teetered bed. The magnetite fraction is discharged by the siphon (12) while the fine slime and light middling overflow a peripheral weir (9) to the overflow launder (6). The bed depth is controlled automatically by float valves (7), which are responsive to changes in the height of clear water supported in the superelevation tubes (8) by the density of the teetered bed. On top of the float (7) is a needle valve (10) which permits

Jan 1, 1963

By H. S. Auvil

[Coals of low-volatile rank cannot be coked without admixing large proportions of high-volatile cod in the used type of byproduct-coke oven, because they expend excessively and. exert side thrust, which ruins the oven wells. Some medium-volatile coals also give trouble. Since high-rank coals produce a strong, blocky coke, it is desirable to have the rank as high as practicable, particularly in the manufacture of foundry coke. Accordingly, it has become the practice to mix or blend high-volatile shrinking coals with as much low-volatile coal as possible and still have a mixture that mill not deform the walls or cause difficulty in pushing the coke. Occasionally, the safe limit of low-volatile cool has been exceeded and ovens have been damaged. It is desirable, therefore, to have a reliable method of determining the expending tendencies of mixtures before they are charged into the ovens. Furthermore, coal changes somewhat in its properties as mining progresses, end therefore, mixtures found to be safe at one time may cease to be so subsequently, particularly if nearly the maximum allowable percentage of low-volatile coal is being used. ]

Jan 1, 1938

By Graham Davey

High-speed stirred milling is a relatively new method of grinding in the metalliferous process industries. However, it has been widely used in the industrial mineral field for more than 30 years. Many existing metallurgical operations are looking to maximize economic return from existing deposits this requires new thinking and technologies. The operating experience of two copper operations is discussed here to show the effect of the introduction of the Metso Stirred Media Detritor (SMD), a new type of high speed stirred mill. Both operations have derived significant metallurgical benefits from this new technology. The benefits and process difficulties are explained. The initial drive in high speed stirred milling technology was toward ultra fine grinding where the mill product has an 80 percent passing size of 15 µm (937mesh) or less. More recently, a number of installations have occurred in a more conventional regrind setting. Few conventional copper concentrators require such fine grinding to attain satisfactory copper grades and recoveries. So other advantages must be considered here rather than just the ability to grind fine with good power efficiency.

Jan 1, 2004

Planning for the Macraes Extension project highlighted the need for additional tailings storage availability. The possible solution of developing new tailings impoundments in Northern Gully, in tum, led to concerns being expressed by the regUlatory authority over the assimilative capacity of Deepdell Creek. Philosophical differences over the appropriateness of applying a seepage model used to set standards in consents for the original project resulted in the company re-evaluating the whole monitoring system associated with tailings disposal and seepage control. Re-evaluation indicated problems arising from the existing in-stream water quality monitoring in respect of protection of the aquatic ecological system and verifiability of results. A new monitoring system was designed relocating the compliance monitoring point out of the stream and into the gully containing the tailings impoundments giving greater certainty of monitoring results to all parties and providing improved protection for the aquatic ecology of Deepdell Creek.

Jan 1, 1993

By J. W. Thompson

ESTATE IN MINERALS. Minerals beneath the surface may be made the subject of separate ownership either by a grant of the minerals by the owner of the land or by a grant of the land excepting the minerals, and thereby an estate in fee simple is created in the minerals, as corporeal things real. Colby, In re, Iowa, 169 Northwestern 443, p. 444. DEEDS EXCHANGING DIFFERENT MINERALS-RIGHTS OF PARTIES. The lands of two adjoining owners were underlaid with cement rock and clay at a depth of about 100 feet from the surface and with coal veins some 600 feet below the surface. By an exchange of deeds one of the land owners conveyed to the other the cement rock and clay with the right to mine and remove the same without entering upon the surface, but the deed contained no covenant not to injure the surface. The other deed conveyed the coal seam and so much of the rock and other minerals just above and below the coal as might be required in connection with the mining and removing of the coal, together with the right to mine and remove the same, and the adja- cent rock, clay, and other minerals, without entering upon or injuring the surface, with one immaterial exception. The deeds do not define the word "surface" and neither expressly nor by implication did they secure to the coal owner the right to subside the overlying cement rock; but the implication is to the contrary, as the deed gives the right to mine and remove coal without entering upon or injuring the surface. The provision that the coal owner should not enter upon or injure the surface amounts to a clause that the coal mine. shall not be worked so as to let down the surface and this does not create any inconsistency with the provision giving the right to mine and carry away the coal.

Jan 1, 1919

Holla has given a good background to the various methods of subsidence control in the coalfields around Sydney.The present writer notes that in many cases, especially with wide longwall panels, there is not the flexibility to alter the mine layout as there is to some degree with the various pillar extraction methods. For this reason it may not be possible to plan the workings to minimise subsidence and some damage to structures may occur. The cost of repair or the cost of subsidence provisions to minimise damage may be small in relation to the tonnages of coal which would otherwise have to be sterilised. One method of subsidence control which has been in use in the Newcastle area since 1970 is the panel and pillar layout (partial extraction layouts with stable pillars). An extracted panel width of 0.6 times the depth of cover resulted in a maximum subsidence of 115 mm for an extracted seam thickness of 2.2 m.As Holla points out, the extracted panel widths in relation to th depth of cover depend on the particular geological setting. His Fig. 3 shows that the subsidence over a panel width of 0.3 times the cover depth in the Southern Coalfield is the same as over a panel width of 0.55 to 0.6 times the cover depth in the Northern Coalfield.Selective pillar extraction and longwall mining can both be used in the panel and pillar layout. Holla's Figs 2 and 3 are used to estimate the maximum subsidence over an extracted panel of known geometry. Maximum subsidence is related to seam thickness. What provision is made for a reduction in subsidence due to the coal which remains behind in a pillar extraction panel if the pillar recovery is poor? The writer suggests that an effective seam height could be used, based on the actual mining height reduced by a factor to account for the percentage recovery of coal from an extracted panel.

Jan 1, 1986

By Robert B. Hopler

First, a definition: “an explosive is called a permissible explosive when it is similar in all respects to the sample that passed certain tests by the national Bureau of Mines, and when it is used in accordance with the conditions prescribed by that bureau. * This was the definition as stated in Miners’ Circular No. 2,” published by the United States Bureau of Mines in 1911, and it is still applicable today. Of course there have been changes over the years, with the name “MSHA Permitted Explosive” now the legal terminology since January 1989, but the old 1911 circular still tells us what the material is. Note that the definition doesn’t even specifically state “coal mining.” A permissible can be required in guy underground operation that is deemed to have a gas or dust hazard, although in 1911 it was certainly meant to refer only to coal.

Jan 1, 1995

By Jon Bowler

Daw Mill Colliery, UK Coal, near Coventry in England, mines the Warwickshire Thick Seam at 800 m/2500 ft depth using longwall retreat with gateroads supported by rockbolts. Over the last eight years the mine has worked longer and wider panels with extraction heights of over 5 m. Recently the mine has experienced high deformation conditions principally from the rib sides resulting in operational issues and production delays. Investigation of rib deformation was undertaken using new inspection and measurement techniques, including systematic laser surveying, and improved rib support consumables were developed and introduced. A new rib trussing system using textile webbing has proved very successful.. A rib support management system was also developed and introduced for face retreat. This allowed rib support to be more effectively managed both for production and safety. For the current developments, new 28-mm-diameter roof and rib bolt systems have been introduced and rib bolt length has been increased to 3 m, with the aim of achieving gateroad stability over the life of the panel. Significant reductions in roof and rib deformation have been confirmed by the latest monitoring results. These ground control innovations are allowing Daw Mill?s potential to be realised. Production from 302?s face in 2008 set new UK and European records. However the support enhancement process continues and further innovations are planned.

Jan 1, 2009

By K. Cybulski

In 2002 a coal dust explosions occurred in the Polish collieries “Jas-Mos” and “Rydultowy” in the Upper Silesia coal basin. In the “Jas-Mos” colliery the coal dust explosion was initiated in the face of gallery by explosives and causing ten death. The stone dust barrier extinguished the flame, stopped the explosion development and saved forty nine miners working in that area. In the “Rydultowy” colliery methane inflammation caused three deaths and seven serious burns and ignited the coal dust explosion. The coal dust explosion was stopped by stone dust barrier and did not cause any victims itself. This paper presents the investigation carried out by the Central Mining Institute Experimental Mine “Barbara” and shows that the stone dust barriers remain still a basic mean for suppression of coal dust explosion in mines. The investigation were aimed at determining the cause of explosion and circumstances that led to their propagation. The evaluation of the state of dust explosion hazard in the areas of accidents have been performed, and the range of flame estimated.

Jan 1, 2003

By L. W. Scott

This report presents an overview of explosionproof (X-P) enclosure research being conducted by the Bureau of Mines, This report emphasizes the increasing importance of research related to the safety con- siderations of X-P enclosures used in underground coal mines. Selected topics are included that summarize results of research in the areas of electrical clearances, reliability of enclosures with windows, safety factors in X-P enclosures, potting materials, performance tests for X-P enclosures, protection against high-voltage explosions, and innovative X-P devices.

Jan 1, 1985

By F. K. McKean

THE task of establishing a new corrosion testing laboratory is more difficult than it need be because there is very little information on the subject available in the literature. Many articles describing tests and results may be found, but a wide search will unearth only passing remarks on the different types of equipment that may be selected for accelerated corrosion tests. An article describing some of the apparatus needed in a corrosion laboratory should be of help to those interested in building a new unit or in making additions to an old one. In May of this year, the writer was given the assignment of equipping a laboratory for general corrosion testing, to form a part of the new Physical Metallurgy Research Laboratories of the Department of Mines and Resource~ at Ottawa. With the help of senior members of the staff, along with what could be gathered from other sources, a list of necessary equipment was compiled and a plan for arranging it in the rooms was decided upon. Where possible, the apparatus was constructed in the excellent machine shops at the disposal of this Department, while the rest was placed on order with the manufacturers.

Jan 1, 1945

By W. M. Dressel

In producing feed for a lead blast furnace, concentrates analyzing 70 to 80 pct Pb are sintered to produce a physically acceptable low-sulfur product which contains only about 50 pct Pb. Mixtures of PbS with varying amounts of SiO2, CaO, Fe 20., and ZnS were heated in an oxidizing atmosphere at 1,000° C; the products were cooled and examined to determine the problems involved in producing sinter with substantially higher lead levels. Microscopic and electron microprobe studies of the above products as well as experimental and commercial sinters indicate that sinters consist essentially of lead silicates, lead-zinc silicate, calcium zinc silicate, and spinel (ferrite). Lead oxide and lead sulfate areas appear to result from insufficient mixing of the materials prior to sintering. The data give an insight into the process and show that sintering results from a complex interaction of all constituents and that sintering is not simply a matter of diluting the mixture to control the oxidation of lead sulfide.

Jan 1, 1975