Search Documents

By G. F. Butterworth

The metallographic structures most frequently encountered in rifle barrels, and which are illustrated by the accompanying photomicrographs, fall naturally into two groups, distinguished by the method used to, produce in the stock a physical condition having the requisite properties. The fist group consists of "rolled" barrels; that is, barrels subjected to hot working by rolling in or near the critical range. In the second group, the stock, which is smaller in diameter than the first, is upset to form the butt end and is then heat treated by giving it a quench and a draw. These barrels will be referred to as " heat-treated " barrels. The structure of the rolled barrels resembles closely that of the same steel after annealing. There is the same network of excess ferrite outlining the grain boundaries, but the grains themselves are composed of sorbite rather than pearlite. The grain size is closely related to the rolling temperature. The critical-point curves of this grade of steel, which is approximately 0.50 to 0.60 per cent. of carbon and 1.00 to 1.30 per cent, of manganese, show a single very pronounced point between 1300" and 1350" F. (704" and 732" C.). Barrels rolled within this temperature range give an exceedingly fine grain, shown in Fig. 1. In fact, the grains may be so fine that, at a low magnification, they may be confused with the heat-treated structure shown in Fig. 6. A magnification of 500 diameters, however, will always resolve a rolled barrel into the characteristic structure shown in Fig. 2. As the temperature is increased, the grains are found to be larger. If, on the other hand, the rolling temperature is below the critical range, the structure previous to rolling will not be obliterated, the only effect of rolling being to elongate the coarse sorbite grains in the direction of rolling, Fig. 3. This distortion is greatest at the muzzle. Heat-treated barrels are quenched in oil from above the critical range, which should give a martensitic structure, Fig. 4, but the presence of some troostite in the martensite is frequently noted when the quench has not been sufficiently drastic, Fig. 5. The structure brought about by the subsequent draw is not so striking, though quite as typical. It is sorbitic or sorbito-pearlitic, and under a low magnification appears almost homogeneous, as in the case of fine grains of pepper and salt well mixed together, Fig. 6. This structure is substantially the same for all

Jan 1, 1920

Most people are familiar with Euclidean dimensions: zero for a point; one for a line; two for a plane; and three for a volume. Howeverbobjects are not actually Euclidean, but lie somewhere between Euclidean æend-membersÆ with a non-integer fractal (or æfractionalÆ) dimension. The fractal dimension D is a measure of the relative importance of large versus small. Consider the trace of a coastline on a map. It has a fractal dimension (1 =D =2) somewhere between a line (dimension = 1) and a plane (dimension = 2). The more tortuous the coastline, the higher the fractal dimension, and the closer it becomes towards a plane. The concepts of fractals and spatial geometry can be applied to a wide range of geologicaVmining problems as well as than those dealing with space. One commonly quoted fractal relation is the log-log relationship of ore-grade and tonnage. Until recently, we have never been able to define or measure spatial-geometry, but new developments in mathematics have provided a means by which to quantity and apply it to our problems.

Jan 1, 1992

Separation of Nickel and Cobalt from Manganese, Magnesium and Calcium by Synergistic Solvent Extraction - From Batch Tests to Pilot Plant Operation The synergistic solvent extraction system consisting of Versatic 10/LIX63/TBP was used for the separation and purification of nickel and cobalt from synthetic laterite leach solution after iron removal. Very encouraging results were obtained for separating nickel and cobalt from manganese, magnesium and calcium. In batch tests, the organic composition of the synergistic system was optimised and very large synergistic shifts for nickel and cobalt were observed. The ?pH50(Mn-Co) and ?pH50(Mn-Ni) values were as large as 1.65 and 2.40, respectively. The extraction and stripping kinetics of nickel and cobalt was fast. Semi continuous extraction tests were conducted with a pH profile of 5.5/6.1/6.5 in three stages at 40¦C. The nickel and cobalt extractions reached 99.9 per cent with only 5 mg/L Ni and <1 mg/L Co left in the raffinate. With two stages of scrubbing, only 2 mg/L Mn and less than 1 mg/L Mg and Ca were left in the scrubbed organic solution. With two stripping stages, the stripping efficiencies of Ni and Co reached over 95 per cent. A fully continuous pilot plant operation was conducted successfully for 280 hours. With an O/A ratio of about 2 and a pH profile of 5.5/5.8/6.0/6.3 for the four stages EX1/EX2/Ex3/EX4, both nickel and cobalt were almost completely extracted. Using a pH profile of 5.4/5.0 for SC1/SC2, the manganese scrubbing efficiency was over 96 per cent. Using three strip stages, over 98 per cent Ni and 99 per cent Co were stripped with only 64 mg/L Ni in the stripped organic solution. The nickel concentration in the loaded strip liquor reached 83 g/L, resulting in a ?Ni of over 28 g/L. The chemical stability of the system was also assessed over 12 weeks under proposed industrial operating conditions. Operation exclusively under strip conditions at 50¦C and 40¦C resulted in LIX63 oxime half lives of 1.1 and 2.1 years, respectively. Operation exclusively under extract conditions at 50¦C and 40¦C resulted in oxime half lives of 0.26 and 0.82 years, respectively. Losses of Versatic 10 were less than four per cent.

Sep 13, 2010

By Sergio N. Monteiro

Polymeric matrix composites with dispersed hard particles are being as wear resistant tools in industrial polishing operations. In the present work, the microstructure of epoxy composites with different amounts of embedded diamond particles, up to 30 wt.%, was investigated for the effect on fracture characteristics. It was found that the introduction of diamond particles promoted an increase the porosity of the epoxy matrix. Moreover, the particle morphology associated with a non-uniform distribution within the matrix was responsible for the nucleation of cracks that caused rupture of the composites.

Jan 1, 2006

By Dave Bulled

"This paper describes the design of an SABC grinding circuit using CEET technology applied to grindability data produced from testing 100 samples and distributed across the blocks of a mine plan using a geostatistical approach. The data distribution required the identification of the location of the sample points and a geological plan of the 130 million ton Ruby Creek orebody together with a mine plan of about 11000 blocks to be mined during the proposed 18 year life of the mine. The mill design was then made with consideration for the estimated hardness of each block in terms of both SAG and Ball milling with allowance for annual periods when the ore is harder to grind. Operating specifications were selected to achieve an optimum of capital and operating costs through use of the CEET program. The geostatistics assigned the statistical error that arises from having a limited amount of sample testing data to the hardness estimate of each block of ore in the mine plan. The final design could then include a quantification of risk and determination of safety factors based on the accuracy of block hardness estimates and CEET model fitting.INTRODUCTIONThe traditional approach to plant design involves the extensive testing of a single large composite sample or a small number of composite samples that are reputed to represent the ore body. It is accepted that the tests used can accurately measure in the laboratory the grindability of the sample by a process representing that to be used in the plant. The size of equipment required to achieve a specified throughput and product size is then calculated from one of a variety of models that have been developed by metallurgists over years of trial and error. Since these tests and models are tried and tested, they are accepted as reasonably precise; however during the operation of the resulting plant the design is sometimes found to be inadequate. It is then suspected that the flaw in the design process lies in the samples not being sufficiently representative of the ore body, since using only a single or small number of composite samples does not recognize the variability of the hardness of the ore, nor does it allow for the lack of precision in the hardness value used in the design.This paper outlines a design procedure suited to an orebody that is described by a geostatistical analysis of a reasonably large number of small samples of drill core. The analysis required the identification of the location of the sample points and a geological plan of the orebody, together with a mine plan of the blocks to be mined during the proposed life of the mine. The mill design was then made using the estimated hardness of each individual block with an allowance for annual fluctuations in the grindability of the ore. The geostatistical analysis assigned a statistical error to the hardness estimates of blocks and of each production year such that the final design included risk estimates and safety factors based on the possible errors that arise from having a limited amount of sample data (Kosick et al. 2002)."

Jan 1, 2007

By Denise Cristina Oliveira Nascimento

Environmental considerations in addition to technical, economical and societal benefits are increasingly promoting the substitution of natural fibers for glass fiber in polymer matrix composites. However, natural fibers are heterogeneous in their dimensions, specially the cross section, which plays an important role in their mechanical strength. It has been found that the equivalent diameter of fibers such as sisal, ramie, pineapple and curaua correlates to different levels of tensile resistance. Piassava is a promising stiff natural fiber for composite reinforcement. In this work, a statistical analysis of tensile strength of piassava fibers using the Weibull methodology was performed. An attempt to correlate the fiber strength, obtained in tensile tests, with the diameter, precisely measured by means of a profile projector, was carried out. The results revealed an inverse dependence between the piassava fiber diameter and corresponding tensile strength. Fracture tip observation by SEM suggested a possible mechanism that could justify this inverse correlation.

Jan 1, 2010

By Forrest T. Moyer

The National Safety Competition was inaugurated in 1925 by the Bureau of Mines, U.S. Department of the Interior, in cooperation with the Explosives Engineer. In the first nationwide contest, 210 mines and quarries were enrolled. In 1962, the thirty-eighth anniversary of the competition, 910 mines and quarries were enrolled. These participating plants were worked a total of 133,292,989 man-hours. Of the enrolled plants, 415 achieved injury-free operations for the year, the largest number of perfect safety records in the history of the contest.

Jan 1, 1964

By Forrest T. Moyer

The National Safety Competition was inaugurated in 1925 by the Bureau o1 Mines, U.S. Department of the Interior, in cooperation With the Explosives Engineer. In the first nationwide contest, 210 mines and quarries were enrolled. In 1962, the thirty-eighth anniversary of the competition, 910 mines and quarries were enrolled. These participating plants were worked a total of 133,292,989 man-hours. Of the enrolled plants, 415 achieved injury-free operations tar the year, the largest number of perfect safety records in the history of the contest. In 1961 and 1962, the National Safety Competition was conducted and sponsored by the Bureau of Mines. In January 1963, the American Mining Congress became a cosponsor and participated with the Bureau in the award activities related to the 1962 contest. The basic purpose of the competition is to stimulate employees to work safely and too give impetus to the building of better accident-prevention programs. A well-designed and efficient safety program helps a company economically by cutting costs, preventing damage to equipment and materials, and reducing nonproductive delays. An effective safety program benefits the employee more directly because his injuries cause personal suffering, lost time, and lower living standards for his family. Since both have much to gain, management and workers should cooperate closely to eliminate disabling work injuries. The greater contest participation and the larger number of perfect safety records indicate increasing safety consciousness on the part of management and employees.

Jan 1, 1964

By William R. Yernberg

The Cripple Creek & Victor Gold Mining Co.(CC&V) celebrated completion of a two-year, $168.5-million expansion and capital improvement program. An open house celebration was held in the historic mining town of Victor, CO on Oct. 4, 2002. Hundreds of townspeople, the press and other invited guests from the mining industry joined the employees of CC&V in the celebration. The event included mine tours, company displays and a barbecue picnic, complete with a country and western band. The Cresson Mine is located about 40 km (25miles) west of Colorado Springs, CO between the towns of Cripple Creek and Victor. The mine is the only large-scale gold mining operation in Colorado and now employs about 300 (ME, October 2001, pp.21-28). The operation is a joint venture between Anglo-Gold (Colorado) (67%), based in Greenwood Village, CO, and Golden Cycle Gold (33%), based in Colorado Springs. CC&V is managed by AngloGold North America. AngloGold North America is the U.S. subsidiary of AngloGold, the world’s second largest gold mining producer. AngloGold is based in Johannesburg, South Africa.

Jan 1, 2002

By J. E. Ryan

General Description Due to the extreme cold weather experienced in Flin Flon during the winter months, thought and precaution were necessary in the design of the plant buildings. The machine shop, carpenter shop, drill shop, and coal plant buildings are similar in the building materials used in their construction. They are sided with two-inch shiplap, insulated with celotex and asbestos paper, and covered with corrugated iron on all side-walls. Roofing consists of 2 by 4 lumber on edge, laminated, and further covered by celotex and three-ply roofing. These buildings are heated by means of unit heaters. The heaters are primarily steam-heated radiators, through which the air of the buildings is circulated by electrically-driven fans. Our machine shop is located to the east of, but central to, the main operating buildings of the mine and plant, and is so connected by a net work of tracks as to be able to serve all portions of the entire plant conveniently. The building is divided into two bays, the main bay 53 ft. by 340 ft., and the east bay 24 ft. by 340 ft. The shop office and drafting room, a two-story annex 24 ft. by 30 ft., is located on the west side of the shop. The arrangement within the shop is such as to house conveniently the several departments, namely, heavy machine tool section, repair floor section, boiler shop heavy tool and floor section, blacksmith heavy tool and forge section, tool room, electric welding rooms, stock room, tin and copper shop, and electrical parts and armature winding and repair shop (see Figure 1). All the heavy tools, the repair floor section, and railway tracks are so located in the large open bay as to be fully serviced by an electrically operated 15-ton bridge crane, with a span of 50 feet and a travel the full length of the shop. A standard-gauge railway track, branched off the main line, penetrates the full depth of the building. This track lies along the extreme east side of the main bay, allowing easy entrance and movement of rolling stock and heavy machinery, loaded on standard flat-cars, to the repair floors in the main bay. Eight jib cranes, affixed to building columns, further facilitate the heavy repair work throughout the various shop divisions. Our light and heavy machine tools are standard equipment, not unlike tools used in mine, mill, and railway shops.

Jan 1, 1935

By J. L. Holman

The Bureau of Mines, at its Rolla Metallurgy Research Center, has devised methods for separating and reusing the major portion of waste plastics discarded in urban and industrial refuse. Waste plastic concentrates from a local collection drive, recycling center collections, urban refuse pilot plants, and the secondary metals industry were separated into three major thermoplastic families--polyolefins, styrenes, and vinyls--based on differences in density using a Bureau-designed sink-float-elutriation hydraulic separator. Other separation methods and systems such as air classification, jigging, liquid media, screening, and electrostatics were studied. Vinyl plastics contain up to 50 percent HC1. It was found that over 90 percent of the HC1 in vinyls can be recovered as usable hydrochloric acid by pyrolysis at 350° C. The remaining pyrolysis products which had heats of combustion in excess of 12,000 Btu/lb, could become valuable as a future source of energy. A characterization study conducted on eight chopped wire insulation wastes from secondary copper and aluminum processors showed that most wastes contained 2 to 7 percent residual metal and large percentages of vinyl. The residual metal content of some of these wastes was lowered to 0.1 percent and the vinyl portion segregated using various separation techniques. The research also suggests ways in which reclaimed thermoplastics may be fabricated into useful products.

Jan 1, 1974

By J. W. Joubert, R. C. W. Webber-Youngman, M. D. Budeba

"SynopsisCost estimation for surface coal mines is a critical practice that affects both profitability and competitiveness. New mines require these costs to be estimated using available information before a project begins. The competitive advantage of a new mine depends on it being both efficient and cost-effective. Low-cost producing mines have a higher chance of survival in a low-price environment than do high-cost producers. The competitiveness and profitability of a coal mine is based on the costs of production and the supply position on the cost curve. There is no single method of cost estimation, and the available methods consider only one or a few variables, leaving out multiple variables that could significantly affect the estimation of mine costs. Mining companies are thus searching extensively for a method that will increase accuracy in the estimation and evaluation of mining projectsThis paper highlights the shortcomings of the available approaches and proposes a data envelopment analysis method to develop a frontier for effective surface coal mines, and the use of a parametric method for modelling the costs and productivity of new mines to ensure effective competitiveness. The models will extend the capability of estimation and the accuracy of estimates using the efficient decision-making units, by considering the optimal mine-specific and external variables affecting costs.IntroductionCoal contributes 25% of the world’s primary energy needs, after fuel oil, which contributes 35%. The world energy demand, estimated over the period 1990 to 2030, is expanding at a cumulative annual growth rate (CAGR) of 1.7% (Schernikau, 2010, p. 14). This emphasizes the need for enhancing the production of existing mines, as well as opening new mines in order to increase the supply of coal."

Jan 1, 2015

Modelling and Optimisation of Direct Reduction of Iron Ore by Coal in a Rotary Kiln

Sep 13, 2010

"Mineral separation by exploiting the differences in mineral or metal specific gravities (sg) has been used since antiquity. In the modern era, this is most commonly seen in the recovery of gold by the use of centrifugal concentrators and the separation of coal (low sg) from waste rock (high sg) using heavy media cyclones and jigs. Other metals, notably oxides of tin and tungsten, are successfully recovered using some combination of jigs, spirals and shaking tables. However, many conventional gravity separation systems are limited to fairly coarse (>1 mm) to medium (>100 micron) particle separations due to the limitations of the gravitational separation forces in conventional equipment.Many of the high specific gravity minerals of interest are friable (e.g. cassiterite, wolframite, etc.) and excessive fines are generated in the grinding/comminution circuits which cannot be recovered with conventional equipment and may be lost directly to the tailings stream. Recent developments in centrifugal gravity separation equipment specifically designed for fine or ultra-fine particle separation and recovery have resulted in heavy mineral particle recoveries as fine as 10-20 microns. Ongoing research work has also identified the benefit of closed-circuit, multi-stage gravity recovery circuits using some combination of centrifugal concentrators and conventional equipment (tables, spirals, flotation, etc.) which can substantially increase overall plant recovery and final concentrate grade.This paper will provide details of the evolution of non-fluidized bed gravity concentrators for high sg mineral recoveries, correlate laboratory scale development work with plant results to confirm scale-up, and show how recent flowsheet developments have contributed to significantly improved plant performance.IntroductionGravity concentration is one of the oldest and most cost effective metal and/or mineral recovery systems, ranging from the classic hand panning of alluvial gold, through to the large scale production of a wide range of metals and minerals, including gold, silver, PGMs, black sands, coal and iron oxides. Conventional gravity recovery systems, comprised of some combination of sluices, spirals, jigs and shaking tables have limited application in fine particle (i.e. <100 microns) recovery, or where there are limited differences in particle specific gravities (sg), e.g. the separation of high sg, high value metal oxides (e.g. those of tin, tantalum or tungsten), from medium sg, lower value metal sulfides such as pyrite and pyrrhotite. These unit operations tend to have limited capacity, and while double and triple turn spirals and multi-deck tables have been developed, extensive floor space is often required in order to process the tonnages incorporated in the modern mineral processing plant."

Jan 1, 2017

By G. Abramov

The 20th Century saw the modern mining industry enriched by one outstanding method of extracting of mineral resources called Borehole Mining (BHM). Mean while, despite its successful track record in wide ranging locales, few specialists are yet aware of this technology. The intent of this article is to introduce borehole mining to a wider spectrum of drilling and mining professionals. The BHM method is based on in-situ water jet cutting of rock mass. On Fig. 1 the schematic of the method is presented. The borehole mining tool 1 is lowered into the borehole 2 and high pressure water 3 is pumped down. At the bottom part of the tool, one portion of that water comes out through the hydromonitor nozzle 4 in a shape of water jet 5 and cuts the material 6 creating slurry 7. The other portion of high pressure water then comes to the hydroelevator 8 (jet pump, eductor) which produces a vacuum. When the slurry reaches this vacuum zone, the eductor sucks the slurry and pumps it up to the surface, where rock parts are separated from water in a tank 9 or a pond and clarified water is pumped down again closing the re-circulating BHM water supply system. The borehole mining tool is suspended on a drill rig tower 10 which allows the tool to rotate and move vertically along the borehole axis. While extracting rock mass, underground caverns (stopes) 11 are created. If necessary, compressed air 12 can be injected to the raising slurry flow to create an airlift effect. Also, a secondary agent 13 (such as oil, foam, etc.) can be added to the stope through the gap between the tool and the casing. As seen from the illustration, BHM is the remote mining method of extracting of mineral resources through boreholes by high pressure water jets.

Jan 1, 2001

By T. A. Sullivan

Refining in a molten salt electrolyte was investigated as a means of recovering nickel containing less than 1 percent and preferably less than 0.2 percent cobalt from nickel products containing up to 5 percent cobalt. Electrolytic separation of nick and cobalt was accomplished in a molten KCl-LiCl-NiCl2 electrolyte. Nickel containing less than 0.10 percent cobalt was routinely prepared. Factors that influenced the transfer of cobalt to the refined product were the nickel concentration of the electrolyte, the cobalt concentration of the electrolyte, the ratio of nickel to cobalt in the electrolyte, and cathode current densities. A method of recovering the cobalt from the electrolyte was developed. The possibility of preparing high-purity nickel by this process was shown, as well as the preparation of various cobalt-nickel-tungsten alloys.

Jan 1, 1968

By Thomas Fraser

WHEN the Bureau of Mines initiated the program of large-scale research and development in the field of synthetic liquid fuels authorized in the Synthetic Liquid Fuels Act of April 5, 1044, the Coal Preparation Section was assigned the task of obtaining data on the preparation characteristics of the coal in large reserves that might be adaptable to use in this new industry. It is natural that, as the rapidly developing general research program brought about new concepts of raw-material quality, preferred geographical location, and the like, the orientation of coal-preparation investigations should have undergone some change. The first major assignment was the sampling and testing of a series of typical American coals deemed to he suitable for hydrogenation based on early research work conducted by the Bureau of Mines. This first series of tests has been completed and is reported in this paper.

Jan 1, 1950

By F. Sillers, R. T. C. Rasmussen

"INTRODUCTION This is the fourth report of investigations dealing with the cooperative tests between the Bureau of Mines and industry on the use of electrolytic manganese in steelmaking. The first report dealt with the use of electrolytic manganese in the manufacture of stainless steel 3/ the second with its use in acid electric steel practice, 4/ and the third with its use in low-carbon basic open-hearth steelmaking. 2/ A résumé of those investigations E7 appeared in the magazine STEEL. 5/ The present report deals with the use of electrolytic manganese in the manufacture of four types of stainless steel and the new Timken 16-25-6 alloy. The Bureau of Mines supplied The Timken Roller Bearing Co. with 62,000 pounds of electrolytic manganese for use in the tests.The electrolytic manganese was produced at the Bureau of Mines pilot plant, Boulder City, Nev., by the process developed by the Bureau and described in Bulletin 463, Operation of Electrolytic Manganese Pilot Plant, Boulder City, Nev., by J. H. Jacobs. J. W. Hunter, W. H. Yarroll, P. E. Churchward, R. G. Knickerbocker, R. W. Lewis, H.A. Heller, and J. H. Linck. The workcarried out under the direction of R. S. Dean, formerly assistant director, Bureau of Mines, and R. G. Knickerbocker, formerly chief, metallurgical branch, as part of a long-range program involving the development, manufacture, and use of manganese from domestic ores. Preliminary arrangements for the plant tests were made by the late A. A. Dow. 7/"

Jun 1, 1947

By David Estrella, Hector M. Lizama, Jhonny Carrión

"Microcel™ sparging systems were installed on one column of the molybdenum cleaner circuit and one column of the copper first cleaner circuit at Antamina. The Microcel™ system is known to generate finer bubbles than jetting-type spargers, and smaller bubbles have been associated with higher recoveries in flotation. Alternating tests were carried out on the molybdenum column, using either jetting-type spargers or the Microcel™ system. Experimental conditions of gas flow rate, wash water rate, and froth depth were tested. Use of Microcel™ decreased the bubble sizes from 2.6-2.9 mm to 1.5-2.0 mm. In addition, Microcel™ improved both unit molybdenum recovery and unit molybdenum concentrate grade. In the copper first cleaner circuit, side by side tests were carried out that compared the Microcel™ column with a parallel columns fitted with jetting-type spargers. Best results were obtained at manifold pressures of 260-290 kPa, where bubble sizes of 1.6-2.6 mm were observed. In either copper or molybdenum flotation, the Microcel™ system required only 50-60% of the gas flow used by jetting-type spargers.INTRODUCTIONAntamina is a copper-zinc mine located in the Peruvian Andes. Compañía Minera Antamina is owned by BHP Billiton (33.75%), Xstrata (33.75%), Teck Cominco (22.5%), and Mitsubishi (10%). The mine was commissioned in 2001 with a capital investment of US$2.3 billion, and has a nominal 100,000 t/d mill capacity. Mining, milling, flotation, and tailings impoundment take place at the mine site, which sits at an altitude of 4,300 m above sea level. The deposit is a polymetallic skarn ore body with intrusive phases of quartz-monzonite porphyry into Cretaceous aged limestone [Evans et al, 2005]. Ore body thickness is 100 to 150 m and has the shape of a flat-lying crescent. Copper is present mainly as chalcopyrite with a minor bornite component. Zinc is present as sphalerite. Molybdenum is present as molybdenite. Some lead, bismuth, and silver are associated with the sulphides. The deposit is currently classified into six main ore types [Dechert, 2006], grouped into two categories: copper and copper-zinc. The mill produces four concentrate types: copper, molybdenum, zinc, and lead-bismuth. Copper, zinc, and lead-bismuth concentrates are transported by pipeline down to the port of Huarmey. Molybdenum concentrates are bagged and trucked to port."

Jan 1, 2008

By Pedro Lilienfeld

This report presents a design and cost investigation for several alternative versions of a field-worthy mining machine-mounted respirable dust monitor. Three main design variations are considered: (a) light scattering sensing, (b) Beta-filter tape sensing, and (c) a combination of the two preceeding methods. Eventual instrument production coats as a function of design complexity are tabulated. Cost estimates for the development and field testing of field-worthy prototypes are also presented. A general discussion on the technical aspects of these design alternatives is included following a modular-hierarchical approach of progressive complexity. The technical background to this report has been provided by the experience and results derived from the work performed under U.S. Bureau of Mines Contracts Nos. H0166097 and H0377092.

Jan 1, 1980