Search Documents

By R. Hamar, G. Lamanthe

"To realize complex shaped pieces, like turbine blades, superalloys are cast with the lost-wax process. The end properties of these parts depend upon their microstructure as well as upon the occurence of casting defects such as micropores and hot tears. Such features are governed by the local solidification conditions which may be describe by the calculation of thermal transfers between alloy and mould. It needs the evaluation of numerous parameters which are fitted from experimental measurements in real castings. In further simulations, any parameter may be changed, in order to determine its influence. Such a single modification is quite impossible to realize in real castings, which shows that numerical modeling is a very good way to study casting processes.This modeling technique of casting is applied here to the real study of a typical low pressure turbine blade of a civil engine.IntroductionAircraft engine manufacturers use superalloys to produce turbine blades. They have to obtain a given microstructure and to avoid solidification defects to give good mechanical properties to theirs castings. For example, microporosity is induced by a large shrinkage that cannot be completely fed with the remaining liquid alloy .The optimization of casting processes needs a good Knowledge of the solidification process, that must be controlled at every place in the casting, and at every time of its freezing. Material and heat transfers that occur during the solidification, can be estimated from rather complex calculations. To model these physical phenomena, the evaluation of many parameters must be made. In this aim, some casting experiments are fitted with numerous thermal captors. The identification of experimental and computed thermograms let us estimate these parameters.A long-range scientific cooperation between SNECMA and INPG has enabled the realization of such studies on this topic. From all of them, this paper describes an experimental and computed investigation which has been led on a typical low pressure turbine blade of a civil engine."

Jan 1, 1986

By Jacob Carr, Bruce Whisner, Adam Smith, Jingcheng Li

Electromagnetic-based proximity detection systems (PDSs) are utilized on mining machinery to protect workers from being pinned or struck. These systems generate magnetic fields covering the space around a machine, and a miner-wearable component (MWC) detects the field. The PDS determines the distance of miners relative to the machine based on the detected magnetic flux density in the magnetic field. This information is used to establish warning and shutdown zones around the machine. Maintaining a stable magnetic field is essential for system accuracy. However, components used to generate magnetic fields can be influenced by temperature changes. Depending on ventilation conditions and seasonal alternation, a PDS can be subject to significant temperature fluctuation. To better understand and quantify this phenomenon, researchers from the National Institute for Occupational Safety and Health (NIOSH) developed an experimental apparatus to study the influence of temperature on magnetic field generator circuits used in PDSs. Results from the study show that the electric current through a generator can be influenced by both ambient and internal temperatures, modifying the magnetic field that is produced. These findings show that temperature can significantly influence the ability of PDSs, used in underground coal mines, to accurately determine a worker’s position in relation to mining machine.

By A. B. Cecala

A few years ago, the National Institute for Occupational Safety and Health and Unimin Corporation developed a clothes cleaning system that is able to quickly, effectively, and safely remove dust from a worker?s clothing without dust exposure to the worker, the work environment, or co-workers during the cleaning process. To perform the process, a worker enters a cleaning booth and activates an air spray manifold which blows the dust from the worker?s clothing. Since the cleaning booth is under negative pressure, all the dust and product removed are contained. In the original design, this dust-laden air was exhausted to a dust collector system. However, since most operations do not have excess dust collector capacity, it was decided to determine an alternative method to provide for a stand-alone cleaning system. This was achieved by ducting the exhaust outside the plant and into the atmosphere. This technique was recently tested and shown to be a viable method to provide for a stand-alone clothes cleaning system.

Jan 1, 2009

Jan 1, 1965

By Lloyd L. Farnham

This paper is one of a series describing the mineral resources of the Nation, including location, history, production, ownership, geologic setting, and mining methods for most of the known manganese deposits in New Mexico, With few exceptions these descriptions are the result of field examinations by the writer. Of 32 counties, the 12 which occupy the western half of the State contain all the known manganese deposits, These counties are Catron, Dona Ana, Grant, Hidalgo, Luna, Rio Arriba, Sandoval, Santa Fe, Sierra, Socorro, San Juan, and Taos. (See fig. 1.)

Jan 1, 1961

By C. Hilgendorf, J. Gingerich, J. R. Boniwell, M. Drouin, D. David on, J. Boldy

The initial discovery of gold in the Eastmain River area, 310 km northeast of Chibougamau, was made by Placer Development Limited in 1970. This discovery resulted from the drill testing of an airborne E .M. Target located in an area of extensive glacial overburden, within an unexplored Archean greens tone belt considered prospective for base metal deposits. Intermittent exploration by another company between 1973-1977 failed to obtain promising results and the existing claims were allowed to lapse. In 1981, Placer reactivated the project and initiated intensive exploration during the next two years which included aerial E .M. surveys, claim staking, ground E .M. and magnetic surveys, geological mapping, diamond drilling and attendant borehole P,E.M. surveys. Beginning in 1983, exploration has been conducted on a joint venture basis with Eldor Resources Limited, The greenstone belt under investigation has an arcuate distribution pattern relative to a centrally located granitic core. Occurrences of gold mineralization defined to date are located to the south of the granite along a strike length of 7 km, and appear to be restricted to the lowermost of two mafic volcanic cycles. This lower cycle is dominated by basaltic flows with subordinate rhyolitic flows and pyroclas ties. Concordant, variably magnetic, massive to talcose ultramafic units occur towards the stratigraphic top of the lower mafic volcanic cycle and appear to crudely define areas considered prospective for gold on a regional bases. Economic interest in centered on a s tratabound, siliceous, sulphide-bearing unit hosted in a 15- 25 metre thick sequence of rhyolite tuffs, basalts and intercalated ultramafics, The siliceous ore bearing unit ( interpreted as a recrystallized chert) contains from 10%-30% pyrrhotite and pyrite with subordinate chalcopyri te and minor sphaleri te. Alteration is characterized by mica development, silicification and carbonatization. Garnets are also occasionally present in close proximity to the ore horizon. The sequence is south facing, and overturned to the northeast at 35°-55°. Explora tory drilling in the vicinity of two conductive targets has been on 100 metre centres along a 1 km strike length of the prospective sequence. To the end of 1983, two ore zones (A and B) have been partially drill tested with estimated indicated and inferred geological reserves of 1 million tonnes grading 11.7 g/t gold , 14.7 g/t silver and 0.26% copper. The system is open at depth. This discovery is the result of the effective integration of geophysics and geology with contributions by many over a long period of time. Key events that can be emphasized are: ( 1) initial area selection of a remote greenstone belt in 1969 - albeit for base metal deposits , (2) utilization of an airborne E .M. system which successfully targeted the A Zone in 1970 , (3) the timely reactivation of the project in 1981 and the subsequent recognition that the original discovery represented a sulphide bearing stratabound horizon with implicit volcanogenic connotations , (4) the intensive effort in 1982-83 deploying aerial and ground geophysics coupled to volcanogenic concepts of ore distribution which resulted in the discovery of the B and C Zones in 1982, and (5) the integration of downhole P . E.M. surveys and geology to successfully delineate ore at increasing depths . To the end of 1983 , $2.6 million has been expended, and it is hoped that continued effort will result in the eventual delineation of an economically viable ore deposit for the joint venture partners .

Jan 1, 1984

By Michael Bayerl

The HILTI OneStep rockbolt was implemented for roadway development in German deep coal mines in 2004. The development by HILTI Company is based on a technical joint venture with RAG Deutsche Steinkohle AG. The technical development of a One-Step bolting system was required for weak strata conditions at the roadway development face. Standard resin bolting has reached the limit of performance when boreholes are squeezed and cannot be filled with capsules. In some cases the heading face is brittle and requires additional support for installation of the bolts and a person working immediately next to the borehole. The Hilti One-Step system allows automated and safe processing at the heading front and provides the key technique to avoid these problems.

Jan 1, 2009

Traditional fine grinding mills in mineral processing relied on the use of steel medium for particle size reduction. The successful development of the Isa Mill(a horizontal stirred mill with 3000 litres of net chamber volume and 1120 kW rated motor power)adopted a novel product separator design that has led to a major revision of medium use in fine grinding. The Isa Mill separator has also successfully operated with a wide variety of medium types such as silica sands, river gravel, smelter slag, run-of-mine ore fractions and steel shots, with size ranges from 0.5 to 10 mm. A great flexibility of the Isa Mill operations has been achieved for processing a feed as coarse as 120 um to a product as fine as 5 µm. This paper discusses the performance of two inert grinding media used in the Isa Mills in Mount Isa Mines of Australia for processing galena and sphalerite bearing ores to below 10 microns. They are the copper reverberatory furnace slag (CRFS)and the heavy medium plant rejects (HMPR). A methodology was also demonstrated for comparing the medium performance and for scaling up the Isa Mills from a 1.5-litre laboratory batch mill to a full scale 3000-litre mill.

Jan 1, 2000

By L. C. IlsLey

"This paper is intended for State mining inspectors, safety engineers of mining companies, and others interested in electrical safety inspection in mines, It presents the important points that should be watched by inspectors, and briefly reviews the work of the Bureau of Mines in the testing of electrical apparatus or equipment to determine their permissibility for use in gaseous coal mines.Important Points in Inspecting Mine Electrical Installations or Equipment.The following questions are intended as suggestions to a safety inspector who may not have been specially trained in looking for defects in installations or in the maintenance of electrical equipment:1.,Is there someone in charge of electrical equipment who is fitted for this position by ability, training and experience?2.,Is a systematic recorded inspection of electrical equipment made at least once each month?3.,Is a plan map of the mine kept showing all permanently installed electrical machinery and apparatus, including cables, conductors light etc.?4.,Are there instructions for resuscitation from electric shock posted in each surface and underground electrical station, also at the entrance of the mine and in the first aid station and are employees working on electrical equipment trained to apply these instructions in case of accident?"

Nov 1, 1923

By H. R. Hardy

Whether the mining engineer is concerned with stress problems in a mine at depth, the development of a new drill bit, or the efficiency of a comminution process, the mechanical properties of the rock with which he must work are of the utmost importance. One of the most popular topics in rock mechanics circles today is ?Is it possible to utilize directly parameters determined from laboratory tests on rock specimens in the analysis of mining engineering problems?? It is the author's opinion that laboratory and .field investigations have not yet reached the stage of development where this question can be answered with any degree of certainty. At present, great difficulties are involved in applying the results of laboratory tests to a mining engineering problem. However, this is due in part to the lack of detailed measurements of stress and deformation in the field and in part to the lack of development of satisfactory structural theories to correlate laboratory and field measurements. Furthermore, if mechanical properties measured in the laboratory are to be directly applied to the analysis of mining engineering problems, the critical mechanical properties must be identified, reliable test procedures must be developed and extensive test programs must be carried out.

Jan 1, 1964

By Christian Roche

Our study is focused on the sub-assembly con-tact shoes, pressure rings and pressure bellows. We were keen to mainly study [ ] 1.The contact shoe design 2.The most efficient pressure to ensure an optimal electrical contact between the contact pad itself and the casing 3. The contact shoe cooling circuit in view to provide to the shoe the best mechanical and electrical characteristics in order to bring to the users of COFOR® components a new standard in process setting technical solutions. A finite elements simulation, combined with a thermal and structural studies were used. Our presentation which follows is dedicated exclusively on the influence of the contact shoe cooling system on the process through a thermal and structural analysis. [ ]

Jan 1, 2007

A well known rock mass classification system has been altered slightly to address the issues found under remnant mining conditions. By detail study of the expected fracture patterns and local geology, the rock mass is classified to indicate the condition of the hanging wall prior to mining. The risk level of each mining step is evaluated by calculating input parameters for computer simulations from the actual rock mass condition. Seismic activity is catered for by the understanding that large event rates and large magnitude events reduce the quality of the local rock mass and that the rock mass stiffness should be adapted accordingly. A case study is presented to test parts of the protocol. Un système connu de classification des masses rocheuses a été légèrement modifié pour faire face aux questions posées par les conditions d’extraction de débris. Une étude détaillée des diagrammes de fragmentation et de la géologie locale permet de classer la masse rocheuse pour indiquer la condition du toit avant l’extraction. Le niveau de risque de chaque étape minière est évalué en calculant les paramètres d’entrée pour simulation par ordinateur à partir de la condition réelle de la masse rocheuse. L’activité sismique est prise en compte avec la réalisation que les taux de larges évènements et les évènements de large magnitude réduisent la qualité de la masse rocheuse locale et que la raideur de la masse rocheuse doit donc être adaptée. Une étude de cas est présentée pour tester des sections du protocole. Ein sehr bekanntes Gesteinsmassenklassifikationssystem wurde abgeändert um die Probleme zu behandeln die unter Restabbaukonditionen angetroffen werden. Durch detaillierstes Studium der der zu erwartenden Bruchmuster und der lokalen geologischen Verhältnisse wird die Gesteinsmasse in Hinblick auf die Konditionen der Flözoberseite klassifiziert. Das Risikoniveau für jeden Abbauschritt wird durch die Eingabeparameter aktuellen Gesteinsmassenkondition für die Computersimulation evaluiert. Für die Seismische Aktivitäten wird Sorge getragen durch das Verständnis, daß große Ereignisraten und Ereignisse hoher Größenklassen die Qualität der lokalen Gesteinsmasse reduzieren und daß die Gesteinsmassensteifheit entsprechend adaptiert werden sollte. Eine Fallstudie um Teile des Protokolls zu testen wird präsentiert.

Jan 1, 2003

By Dave Bulled, Khiratt Husain

"The use of High Pressure Grinding Rolls is gaining significant interest as a replacement for SAG milling in the comminution of hard rock ores because of the potential for reduced costs in terms of energy and grinding ball consumption. Estimation of expected energy consumption for fullscale operations has conventionally involved the testing of a few fairly large samples in pilot scale HPGRs. This paper describes the development of a small-scale batch test method for determining a work index for HPGR of a large number of samples that can be used to show the variability of the ore as an integral part of a geometallurgical approach to circuit design and production forecasting.The test equipment that was developed comprises a hydraulic press with adjustable pressure operating on small batches of ore in a locked cycle test procedure. A work index measurement was determined that links the specific energy consumed in the test to the breakage achieved such that the index can be used to predict comminution energy requirements.The measurements were calibrated against laboratory scale HPGR equipment to develop a model for design and forecasting that includes crushers, HPGRs and ball mills in a complete comminution circuit.INTRODUCTIONEstimation of the expected energy consumption for full-scale HPGR operations has conventionally involved the testing of a few fairly large samples in laboratory and pilot scale machines (Danilkewich, 2006). With the financial input of five mining corporations, SGS Lakefield Research has developed a small scale test capable of providing relevant information on the variability of energy consumption and size reduction from drill core samples. It is our intention that the values measured in the test will be scaled up, through benchmark comparison with pilot sized and full sized HPGR units, to allow plant design and throughput forecast on a block by block basis of the mine plan using a new CEET program. CEET® (an acronym for Comminution Economic Evaluation Tool) is an advanced grinding design and performance predicting tool that uses energy relationships to model the performance of SAG / Ball mill circuits."

Jan 1, 2008

By Frank E. Cash

The compensation-insurance rates for quarrying in North Carolina are 11 times higher than for the State?s major industry, textiles. Some operators are willing to accept this as representing the ratio of existing hazards. This was not true of the management of the Southern Aggregates Corporation, and in 1935 it tools definite steps to correct the idea of its local officials and employees that loss of life and limb in quarries is inevitable. ACKNOWLEDGMENTS The authors acknowledge gratefully the assistance and information concerning these operations furnished by H. M. Shaw, safety director (also secretary and treasurer), Southern Aggregates Corporation, Raleigh, N. C.; by the following superintendents: J. H. Rodgers, Blair Quarry, Blair, S. C.; J. D. Lane, Greystone and Rolesville Quarries, Henderson, N. C. ; J. H. Arthur, Guilquarry, Stokesdale, N. C.; J. H. Watkins, Rockton Quarry, Wendell, N. C.; P. A. Wellenborne, Reidsville Quarry, Reidsville, N. C.; and J. L. Kirchin, Woodleaf Quarry, Woodleaf, N. C.; by the various foremen at the plants, and by Murry Id. Grier, safety engineer, North Carolina Department of Labor, Asheville, N. C.

Jan 1, 1940

By Alfred Wild

The Kraftile Co. plant, Fremont, Alameda County, Calif.--the largest producer of glazed, structural wall units west of the Rocky Mountains--maintains modern processing facilities to evaluate and blend a wide variety of clays from several sources to produce quality products. The report desribes the prospecting, exploration, and test methods used to locate raw material sources and covers processing methods, cost factors, and trends. Also, the geologic and ceramic factors are considered in a general discussion of the economics, potentials, and requirements of clays as raw materials for ceramic tile manufacturing.

Jan 1, 1963

By Jay Tuttle

THE spiral stoping method of mining was first seen by the writer at the Granby Consolidated Mining, Smelting & Power Company's Hidden Creek mine, at Anyox, British Columbia. Where the method received its name, or by whom it was named, is a question, but it was employed by the Granby Company at their Phoenix mine, in the Boundary district, B.C., as early as 1901-02 after they had tried unsuccessfully other methods at that large, law-grade property. its adoption there was suggested by two miners, John and Steve Swanson, then working at Phoenix, who had previously been employed in the hard iron-ore mines of Michigan and Wisconsin, where they had learned this system of mining. The method proved successful at Phoenix and also, later, at the Company's Hidden Creek mine at Anyox, where some 40,000,000 tons, or more, of ore was mined in this manner during a period of about thirty-five years.

Jan 1, 1939

By Michelia Alba, Ronaldo S. Sampaio, Davi S. Braga, Mathieu Dubé

Climate change is pressuring industries and governments for decarbonization commitments, research, testing, and use of best practices to achieve the target of global warming below 1.5/2 °C. As it accounts for as much as 7% of all global CO2 emissions and 7% of energy consumption, the steel sector needs to address this issue with extended efforts. This paper provides information on the key potential of renewable biochar as an alternative fuel for pellet production. It also summarizes the successful application of biochar in a pioneering case study as the main fuel for a Grate-kiln pellet plant in Brazil, as well as the study of its use to replace coke and anthracite as an additive for iron ore pellets and other possible applications in the steel industry in COREM's precompetitive research & innovation program. The final discussion reveals the large quantity of biochar required by the Brazilian and Quebec scenarios for reducing CO2 emissions of iron ore pelletizing plants.

Jan 1, 2023

By Mark R. Pettitt

The charter of this investigation was to identify and promote the application of noise control technology to future longwall mining machinery. Intensive noise and vibration data were acquired on a typical longwall shearing machine, and the highest noise levels were shown to radiate from the cutter drums. Shearing machine cutter drum noise control techniques that take advantage of the nature of the dynamic forces generated during coal cutting were developed. These include both structural redesign and force isolation techniques. A reduced noise cutter drum was developed that achieved a 5 to 6 dBA system noise reduction at the operator's position. Its operational performance was verified by a six-month long in-mine test. It was evident from the data that additional noise reduction could be achieved by treatment of the shearing machine hydraulics. Noise control of secondary sources was also investigated. A method of reducing full or empty stage conveyor noise (and continuous miner conveyor noise) by 5 to 10 dBA was demonstrated through isolation techniques. Underground mine durability testing, however, is yet to be demonstrated.

Jan 1, 1986

By E. Petrakis, K. Komnitsas

The main objective of batch grinding modeling is the estimation of the product particle size distribution over time or specific energy input to the mill. So far, the developed analytical methods require often complicated calculations which are timeconsuming. Thus, more simple approaches that allow the reliable prediction of the complete product size distribution need to be developed. In the present paper, an approach, based on the population balance model (PBM), that reliably predicts the product size distribution is proposed. In order to enable this, the simplified form of the fundamental batch grinding equation was transformed into the well-known Rosin–Rammler (R-R) distribution, thus allowing the determination of the breakage rate for each grinding period. A time-dependent breakage rate framework was developed where the traditional linear theory of the PBM is considered a partial case. This approach allows the deviations from the linear theory to be categorized and the degree of the acceleration-deceleration of the breakage rate to be predicted. Modeling results were validated by laboratory grinding studies using two homogeneous materials, quartz and marble, and one heterogeneous, a limonitic laterite. The experimental data revealed that grinding exhibits non-first-order behavior and the degree of deviation from the linear theory depends on the tested material. The reliability of the proposed model was validated with the use of the distribution modulus n, the a value of the breakage rate parameter, and the optimum n values that minimize the sum of the differences between the experimental and estimated particle size distributions.

Feb 8, 2021

By C. Machio

This paper reports the results of a study to determine the effect of process control agent (PCA) on the characteristics of Ti-Mg powders during milling. It has been shown that a 2% increase in PCA content leads to up to a 40% increase in yield of the milled powder but reduces the kinetics of the mechanical alloying process. The introduction of 4% PCA decreases the mean powder particle size by up to 30%, whereas 6% PCA increases the mean particle size by up to 230%. The characteristics of the milled powders will be discussed in relation to the role of PCA in the milling process. Keywords Titanium?magnesium, mechanical alloying, PCA.

Jan 1, 2011