Search Documents

By Joel Nonnweiler, Rafael Castro, Ross Webb

The three thousand foot long 66-inch diameter Folsom East Interceptor Section2B was completed accident free, on time and under budget with no measurable surface settlement. The tunnel passed through nested cobbles, highly abrasive sands and gravels, and abandoned mine workings with less than five-feet of cover at times. Preventing settlement was critical since the tunnel passed under a heavily traveled state highway. A pilot project to test microtunneling and pipejacking methods in the same ground conditions abandoned both drives before completing the planned drive lengths. This paper discusses performance of the conventional tunneling method selected to excavate the ground and the effectiveness of the ground modification techniques employed.

Jan 1, 2001

By Roy E. Peterson

The Bureau of Mines conducted bench-scale research to evaluate materials which showed potential as low-cost reductants for use in the ironmaking industry. These materials were lignite, subbituminous coal, coal char, tree trimmings, refuse--derived paperboard, used crankcase oil, and peat. To compare their effectiveness, the materials were tested in the reduction roasting of nonmagnetic taconite and, except for oil and peat, in the reduction of iron oxide pellets to metallized pellets. Reduction was conducted in a 18-cm-diameter, rotary drum, which was externally heated in an electric furnace. Over 92 pct of the iron was magnetically recovered from a nonmagnetic taconite after roasting with any of the reductants, but greater quantities of reductant were required to achieve this when the waste materials were used. The fossil fuels were also more effective for metallizing pellets, although metallizations above 90 pct were also obtained with tree trimmings and refuse paperboard. However, refuse paperboard had to be frequently recharged to the furnace because it depleted rapidly.

Jan 1, 1983

By J. P. Ducarme

Numerous fatal/nonfatal accidents involving underground workers struck by powered machinery occur yearly, with continuous miners and roof bolters involved in the majority of these accidents. In an attempt to reduce these accidents, researchers at the the National Institute for Occupational Safety and Health (NIOSH) Pittsburgh Research Laboratory conducted studies of operator interactions with the motions of continuous mining machines and roof bolter boom arms. These operators generally perform their tasks in close proximity to the equipment in confined workspaces, often employing awkward postures. Since experiments with human subjects using the actual equipment were not feasible due to safety concerns, researchers opted to conduct controlled experiments in laboratory settings. Utilizing motion capture technologies and computer simulations, the studies collected data on equipment and operator movement in a range of seam heights and working postures. This article details the results of these studies to examine operating speeds based on usage and seam height.

Jan 3, 2010

By R. F. Abernethy

Recent investigations in the United States and in other countries have produced considerable information on the nature and occurrence of minor elements in coal. The possibility of recovering certain elements, particularly germanium and uranium, from coal ash and other coal products has received considerable attention. Some flue dusts are potential sources of germanium, and certain lignite deposits are potential sources of uranium, but industrial recovery of these elements has been limited to small quantities for technical and economic reasons. Considering the large amount of coal mined annually, a small percentage of a rare element may have industrial significance if an economical method of recovery can be developed. In 1944 information on the occurrence of rare elements in coal was reviewed in Bureau of Mines Technical Paper 669 (46).3 This report is a revision of that paper with the view of summarizing published information available for United States coals, and pertinent information concerning coals of other countries. Selected references from the original paper are retained. New references do not include all preliminary reports when more permanent literature describing complete projects is available. Consequently, the list of references should not be considered complete.

Jan 1, 1963

Abstract : The computation of reliability index or failure probability of slopes can be transformed into an optimisation problem. In high rock slope engineering, it is usually a multimodal optimization problem. The traditional optimization techniques are difficulty to find out the global optimal solution because of their easily falling into local optimal value. Recently, a new kind of bionic algorithm - ant colony algorithm (ACA) - has been used to solve this problem. In this paper, the structure of ant colony algorithm and the transfer probability of ants are modified to evaluate the failure probability of complicated slopes. A new adaptive ant colony algorithm (AACA) is proposed to determine critical slip surface and its corresponding failure probability of complicated slopes. A case study is given to verify the proposed approach. The results show that the presented method has obvious advantages compared with traditional methods. ZUSAMMENFASSUNG: Die Rechnung des Zuverlaessigkeitindexes oder der Zerstoerungswahrscheinlichkeit kann sich in einer Optimierungsfrage umwandeln, im Bauprojekt an hoehe Gebirgehang, handelt es sich meistens um eine Optimierungsfrage ueber Multi- Spitzenwert. Mit der traditionelle Optimierungsmethode ist es schwer eine umfassende Loesung fuer die Optimierung zu finden wegen des leichte Verfallens in Beschraenkung der Teiloptimierungsloesung. Mit dem neue Bionik- Algorithmus —— Ameisen - Kolonie- Algorithmus wird dieses Problem geloest. In diesem Text hat man eine Strukturverbesserungsloesung fuer das Ameisen- Kolonie -system und die Wahrscheinlichkeit der Ameisenkolonie erwaehnt, und damit wird man die Zerstoerungswahrscheinlichkeit des komplizierte Hangs feststellen. Mit dem neuen Ameisen- Kolonie- Algorithmus kann man die gefaehrlichste Gleitflaeche und die entsprechende Zerstoerungswahrscheinlichkeit herausfinden. Die in diesem Text beschriebene Methode wurde durch Praxis geprueft. Durch die Pruefergebnisse wurde es gezeigt und bestaetigt, dass der neue Bionik- Algorithmus vorteilhafter als der traditionelle Algorithmus ist. Résumé : Le calcul de l’indice la fiabilité ou de la probabilité de ruptures peut être transformé en un problème de l’optimisation. Pour le cas du génie des pentes de haut rocher , le problème se pose en général en l’optimisation de multi-crêtes. Les techniques traditionnelles conduisent facilement à la solution optimal partielle au lieu de celle globale. Récemment un nouveau type de bionique algorithmique a été appliqué pour la solution de ce genre de problèmes, c’est l’Algorithme Colonie de Fourmis. Dans l’article il est proposé de modifier la structure du système de la colonie de fourmis et la probabilité de transfert des fourmis en vue d’évaluer la probabilité de ruptures des pentes de haut rocher complexes, par ailleurs un nouveau algorithme adapté de colonie de fourmis est formulé pour déterminer la surface glissante critique et la probabilité de ruptures correspondante. Les techniques proposées dans l’article sont vérifiées à travers des expérimentations dont les résultats ont prouvé que les techniques présentées dans l’article sont évidemment meilleures que celles traditionnelles.

Jan 1, 2003

By Pierre De Pasquale, Aquilino Antonio Alvarez-Castro

Greenhouse gas emissions are now an essential issue for extractive industries. Actually, lowering of quarry energy consumption and CO2 emissions participates to answer both environmental and financial issues. The “EE-Quarry” European project, supported by the European Commission (EE stands for Energy Efficient), develops a new and highly effective modelling and monitoring Energy Management System technique to improve Energy Efficiency and move to a low CO2 emission rate in the nonmetallic mineral industry.

Jan 1, 2016

By P. Falcão Neves

A detailed analysis of the geomechanical behaviour in rock cutting with a diamond saw is provided to obtain a better understanding of the mechanisms involved in the process. The energy of elastic deformation (before failure) and plastic deformation (post failure) was determined in uniaxial compression tests as well as the energy consumed per unit volume in the cutting process. The test samples are White and Ruivina marbles from Borba - Vila Viçosa in Portugal. Correlations between total deformation specific energy and cutting specific energy, normal and tangential forces and diamond indentation are analysed, and some conclusions are presented.

Jan 1, 2012

The seams of black coal occurring in Victoria are so disturbed by faulting, wash-outs, thinning, etc., that it is necessary, for the prevention of costly errors in development, that close boring be undertaken so that the correct positions of the shafts, tunnels, main and auxiliary roadways can be set out in order that the area can be economically worked. The State Coal Mine has two boring plants continuously at work, which have given good service for the last twenty-five years.The information supplied herein is merely our experience in boring at the State Coal Mine over an extended period. The type of plant in use is that known as the Victoria Drilling Plant, equipped with an 11 h.p. portable oil engine, using power kerosene as fuel. It was purchased in 1914, complete with mechanism for cable drilling, capable of boring to a depth of 1500 ft. with a guarantee of 1000 ft., with Calyx cutters, boring rods and all necessary equipment for the sum of £1473. The chief mechanical features of the plant are as follows:-The derrick is in the shape of a tripod (see Fig. 1), two of the legs being of steel channel built together to form a frame which, when lowered on to two sets of road wheels, forms a carriage for the transport of a portion of the boring equipment. The third leg is made of oregon in the form of a double bow, with bolts and distance pieces between the wooden sides. The top of this is hinged on to the steel frame, and the bottom is fitted into a cast iron block, having two small wheels to facilitate erection. A rope attached to the cast iron block and to the winch easily...

Jan 1, 1936

Recent literature is reviewed with emphasis on the design and scale up of mixers. Most important aspects of mixing have resulted from the study of Newtonian fluids and only a minor attempt has been made to extend the work to non-Newtonian materials.The rheology of non-Newtonian materials is outlined and the typical behaviour of mineral slurries is indicated.The importance of flow velocity, flow pattern, and fluid turbulence is discussed with relation to suspension of solids and rate of reaction.Data on experimental leaching of ore from Mary Kathleen, Queensland, show the effect of different mixing impellers.In conclusion, factors involved in the selection of a mixer are presented with emphasis on economic appraisal after pilot experimentation.INTRODUCTIONThe subject of mixing has attracted considerable attention during recent years, but relatively little work has been undertaken for the study of non-Newtonian materials. Most work has been restricted to Newtonian fluids because there are less inconsistencies in such study.Mixing, by definition, implies blending or combining, and ranges from gentle mixing which blends the contents of a large tank in 24 hours to violent mixing which completely homogenises the contents of a tank within seconds. Metzner and Otto (1957) have pointed out the present lack of knowledge on the degree (or quality) of mixing. Apart from this fact the design of mixers for Newtonian materials would seem to be reasonably certain.Both capital and operating costs rise rapidly with increasing mixer size. Therefore the design, or selection, of a mixer is a matter for economic consideration in the overall aspect of plant design and operation.

Jan 1, 1961

By K. Y. Haramy, R. O. Kneisley

This U.S. Bureau of Mines report summarizes a study of large-scale strata response to longwall mining at a western U.S. coal mine. This study utilized surface and subsurface measurements, geologic mapping, in situ stress measurements, and pressure cell readings to characterize strata behavior. Preliminary analysis of surface subsidence and time-domain reflectometry (TDR) was used to determine a suggested main roof caving sequence. Coal ejected from the face apparently resulted from brittle failures that occurred because of lack of significant yield zone development. The combination of a strong coal with pronounced directional behavior, low overburden pressures, a good caving roof, and a high-production environment that minimized time-dependent loading apparently reduced yielding of the longwall face. The panel 1 headgate-entry design appears adequate; however, the abutment pillar and adjacent panel tailgate rib are highly stressed and may contribute to problems during second panel mining. The small chain pillar yielded after passage of the face, but the pillar width may be near maximum since evidence of a stressed core exists.

Jan 1, 1992

By Roger S. Jackson

"This study interprets vibrations produced by single underground shots, recorded on surface by 135 digital seismographs laid out in four linear arrays. Several vibration anomalies were observed and are investigated. A novel method of displaying the blast-induced vibration iso-contour data relative to the three-dimensional representations of the geological rock units and structures leads to the following interpretations:• The identified faults commonly dampen or amplify vibrations, on the evidence of the peak particle velocity,• Strong anisotropy of geologic formations produces different vibration attenuation in the various directions of interest,• Low-vibration “depressions” can be related to the presence of faults, and• Higher vibration levels than expected based on ‘scaled-distance’ principles are observed close to intersecting faults.The interpretations from this study document a better understanding of the geotechnical influences on blast induced stress wave propagation in a geologically complex area. The practical benefit of this understanding is better control of surface vibrations, experienced from underground mining activities."

Jan 1, 2010

By T. O. Llewellyn

The Bureau of Mines conducted batch-?scale tests on a sample of parphyry copper mill tailings as part of a study to determine the feasibility of rutile recovery from this source. The tailings that were tested contained 0.75 percent titanium dioxide (Ti02), with about two-thirds of the Ti02 values occurring as rutile. Mineralogical studies indicated that about one-half of the Ti02 content could be considered recoverable. Beneficiation studies of the tailings showed that best flotation results were obtained when sulfides and carbonates were removed by bulk flotation prior to rutile flotation. Rutile flotation was most effective when a petroleum sulfonate collector was used in an acid circuit. From this basic method of flotation, two alternative procedures were developed. The first procedure was to size and grind the tailings to minus 200 mesh; deslime the total pulp; and then float the sulfides, carbonates, and rutile. The second procedure was the same, except that it did not include sizing and grinding. Flotation of the sized and ground tailings yielded rutile concentrates containing 43.1 percent Ti02 and 75.7 percent of the recoverable Ti02. Rutile concentrates floated from the tailings that were deslimed but not ground contained only 34.7 percent Ti02 and 69.4 percent of the recoverable Ti02.

Jan 1, 1980

By W. H. Goghill

Numerous investigators have studied grinding. Each has contributed his bit to a literature that is difficult to correlate. Too many of the results have been transformed into curves with so many "inflection points" and "counterflexures" that they obscure the issue. Some of the investigators have neglected the very essence of the problem, namely the power and the amount of material to which a known amount of work was applied. The purpose of this paper is to show the ease with which results can be interpreted when these quantities are duly recognized. Some grinding tests will be given for illustration. Grinding studies are of two kinds: (1) Study of the character of the ore and (2) study of the performance of the machines. Several ores may be crushed by a given machine, or several machines may be used on a given ore. The illustrations given in this report cover both objectives.

Jan 1, 1934

By Bruce I. Thomas

[THIS PAPER, tine of a series on placer ml n in iii Alaska, describes mining methods and gives unit costs at operations where hydraulic and mechanical excavation equipment is used with nonfloating washing plants. The mining methods described were developed during the last 30 years to copy with conditions peculiar to arctic and subarctic regions arid are now used by a large segment of the placer mining industry in Alaska. The operations described have been classified if m ii into three main categories: Those having sluices at a bedrock level, those having sluices above bedrock and those having mobile nonfloating washing plants (dryland dredges). Diesel-powered bulldozers and draglines convey or clevate gold-bearing gravel to the sluices, remove tailings, and strip waste gravel and other overburden. Diesel-powered centrifugal pumps supply water foe sluicing and hydraulic stripping. Detailed descriptions and unit cost arc presented for 14 operations to illustrate the numerous arrangements udder the first 2 categories.]

Jan 1, 1959

By Frank C. Townsend

Waste disposal schemes using spent shale in embankments require a thorough knowledge of its geotechnical engineering properties for environ-mentally safe disposal. In this context, the objective of this laboratory investigation was to determine the physical properties, geotechnical properties, and composition of spent oil shale retorted by the PARAHO and TOSCO processes. Physical properties consisted of mechanical analyses, Atterberg limits, and specific gravity determinations. Geotechnical engineering properties were determined by compaction, maximum-minimum density, unconfined compression, triaxial compression, permeability, direct shear, Ko, cyclic tri-axial, resonant column, and Los Angeles Abrasion tests. Petrographic, chemical, and scanning electron microscopy analyses were used to determine compositional features. Unprocessed shale is hard and durable and more properly described as a carbonate rock instead of shale. PARAHO is classified as a GP, while TOSCO classifies as an SM. PARAHO requires no moisture for compaction to maximum densities; however, TOSCO does. Retorting causes a loss in durability but creates self-cementing characteristics, which for PARAHO a 3-to 8-fold strength increase was observed, while for TOSCO the increase was 1.5 to 3 folds. The shear strength, compressibility, and dynamic properties of compacted PARAHO are comparable to those for sandy gravels. Compacted PARAHO is semipervious, while compacted TOSCO can be semipervious to impermeable.

Jan 1, 1979

By D. Harrington

This circular presents part I of a series of papers of a review of the literature on air conditioning in mines, with particular reference to the health, safety, and efficiency of miners. It deals with the physiological aspects of exposure to air contaminated by organic matter, noxious and toxic gases, and dusts that emanate from various sources in underground workings; part II will discuss the relation of abnormal mine temperatures and humidities to the health and efficiency of minors; and part III will describe theoretical and practical methods of air conditioning mines to correct or alleviate the conditions mentioned and will discuss the results attained by some of the systems now in use in various parts or the world.

Jan 1, 1938

By Charles L. Parsons

Early in 1912, from information received by the Bureau of Mines, it became evident that quantities of valuable radium-bearing ore from Colorado were being exported for manufacture in foreign countries and that at least part of the manufactured product was being returned to this country and sold at a price entirely incommensurate with that received by the miner and the prospector. Consequently, in line with its efforts to increase efficiency in the mining and treatment of mineral resources, the Bureau of Mines undertook an investigation of conditions. Results of this preliminary investigation were published, in the summer of 1913, as Bulletin 70,a which gave an outline of the radium deposits of the West, the conditions of mining, the wastes involved, and the status of the production of radium from its ores. At about this time newspapers and medical journals were publishing statements regarding the value of radium in cancer therapy. These reports, although many of them were exaggerated, brought out clearly the remarkable virtue of the gamma rays for the treatment of cancer and other malignant growths. In view of the fact that the largest known supplies of radium ore in the world are in the States of Colorado and Utah and on the public lands of the United States, it was deemed highly important for the Bureau of Mines to study the production of radium in detail. Such study, it was hoped, would enable the prospector and miner to obtain a fairer price for the ores and would furnish information necessary in case Congress appropriated funds to develop methods for extracting radium from ore on the public lands under Government supervision, to be supplied at cost to the hospitals of the Army, Navy, and Public Health Service.

Jan 1, 1915

By A. R. Kiani-Rashid

In this paper, the effect of aluminum content on the formation mechanism, volume fraction, morphology and particle size distribution of graphite has been investigated. Addition of aluminum on ductile iron causes some fundamental changes in iron-carbon phase-diagram and as a result, improves the graphite formation during eutectic transformation. The results reveals that aluminum compounds have been formed in the core of graphite nodules, thus aluminum plays an important role in the formation of graphite nodules. Furthermore, it is indicated that an increase in the aluminum content also leads to an increase in the number of graphite nodules and a decrease in the nodules size. By using EPMA, the segregation of aluminum and silicon between graphite nodules has been studied

Jan 1, 2010

By G. E. McElroy

This report discusses the construction and use of an all-pressure psychrometric chart in which the requirements of simplicity of appearance and absolute accuracy have been waived, to a certain extent, to provide for the rapid determination of psychrometric data and for the rapid solution of air-conditioning problems of major interest to the mining industry. Many mines in which air-conditioning problems are important are situated at elevations far above sea level and embrace great differences in elevation - in excess of 8,000 feet in certain mines - throughout their airflow circuits. Under these conditions, the effects of variations in the pressure of the atmosphere upon the physical properties of the mixture of air and water vapor of which it is composed are considerable and should be taken into account in the solution of problems. The simple types of psychrometric charts in common use, such as the Carrier, Bulkeley, Hill, and Goff (American Society of Heating and Ventilating Engineers Guide), are not generally suitable, in that they are drawn for a single barometric pressure - 29.92 inches mercury.

Dec 1, 1947

By J. P. Carson

The works of the Tula Iron Company are in the Republic of Mexico, State of Jalisco, twenty-eight leagues southwest of Guadalajara, ten leagues northwest of the town of Sayula, through which passes the projected line of the Mexican National Railroad. Its geographical position would be about: latitude, 20' 10' N., longitude, 40 35' w. of Mexico City. The surrounding country is a rolling plateau, 6000 feet above the sea, enjoying the most magnificent climate in the world, the average temperature being about '70'. The works were commenced in 1850 by a company with very small capital, having not the least idea of the undertaking. They soon fell into the hands of the money-lenders, and after changing

Jan 1, 1879