Search Documents

Researchers from the National Institute for Occupational Safety and Health (NIOSH) are developing a coal pillar rib rating (CPRR) technique to measure the integrity of coal ribs. The CPRR characterizes the rib composition and evaluates its impact on the inherent stability of the coal ribs. The CPRR utilizes four parameters: rib homogeneity, bedding condition, face cleat orientation with respect to entry direction, and rib height. All these parameters are measurable in the field. A rib data collecting procedure and a simple sheet to calculate the CPRR were developed.

Jan 7, 2020

By Forrest T. Moyer

INJURY experience and related employment information are presented in the chapter for the coal-mining, coking, oil and gas, peat, and native asphalt industries in the United States for 1964. No attempt has been made to combine these data and present injury-frequency rates reflecting the mineral-fuel industries because the hazards of the separate industries are not comparable. All rates in the text are calculated separately on data before rounding, hence component rates may not add to the total rates shown in the tables. Tabulations showing the trend of injuries and employment for all mineral industries are presented in Volume III. COAL Injury experience of the coal mining industry was improved in 1964, as measured by the declines of 1 and 14 percent, respectively, in the frequency and severity rates. Although the total number of injuries increased in 1964, a slightly greater proportional increase in man-hours worked caused the frequency rate to drop to 44.65 per million man-hours. The injury-severity rate in 1964 was 7,832 days lost per million man-hours of exposure. Employment and injury data for 1964 are based on final data for anthracite mines and preliminary data for bituminous coal and lignite mines. Fatality experience improved significantly with a record low number of 240 deaths in 1964. This total was 44 less than in 1963. The Nation's coal mines during 1964 were free of major disasters (a single accident resulting in the death of five men or more) for the first time since 1956. The

Jan 1, 1965

By M. -C. Noël, G. P. Demopoulos

In this work the formation and environmental stabilization potential of arsenate-containing fluoroapatites is considered. In particular in this research various compounds were precipitated from synthetic solutions containing fluoride, arsenate/phosphate and calcium by varying different parameters-temperature, Ca:As ratio, pH, and P:As ratio, and aging time. The results obtained helped determine the operating window that should be used for the formation of highly crystalline fluoroapatites, in particular svabite (Ca5(AsO4)3F). It was found that svabite has a specific pH range of precipitation, with lower pH yielding CaF2 and calcium arsenate compounds such as CaHAsO4•H2O. At higher pH, a mixture of svabite and johnbaumite (Ca5(AsO4)3OH) precipitated, yielding a less stable material. This range of precipitation varied with the concentration of arsenic in the starting solution, and widened with higher initial concentrations of Ca2+, AsO4 3- and F-. Furthermore, svabite/fluoroapatite solid solutions were formed by using the same procedure as svabite but replacing some of the arsenate in solution by phosphate. The increase in phosphate content yielded a gradual change in morphology and crystallinity. Work on stability evaluation is currently under way.

Jan 1, 2014

By M A. Mongillo

Most geophysical and geochemical data collected during regional exploration programmes are in vector form (location, value), and have traditionally been presented and interpreted in a profile or contour map format. However, the human vision system can interpret data presented in image format much more easily and new information is often revealed by the judicious application of powerful interactive computer image enhancement techniques. This paper describes a practical demonstration of the application of such tools to gravity and resistivity datasets from the Central Volcanic Region of theNorth Island.   Filtering, contrast enhancement, relief shading, pseudo-colouring and then overlaying of the gridded datasets in image format has helped identify inter-relationships such as the association between many low resistivity anomalies (epithermal deposits or geothermal resources) and the edges of large gravity anomalies (calderas or grabens). Similar revelations should result from the application of these tools to the integration of other mapped datasets from geophysical, geochemical and geological disciplines.

Jan 1, 1992

By T. C. Moore

This report describes the feasibility test of an electromagnetic method for locating boreholes, with or without casing, that have been drilled in conjunction with mining operations but whose location with respect to the tunnel is not precisely known. The first tests were conducted with the cooperation of the Kerr-McGee Corporation, Church Rock Mining Operations, New Mexico, in September 1977. These tests demonstrated that accuracies of better than ±5% of range and ±1° of bearing can be achieved with a simple system and setups. Subsequent tests, in January 1978, on a horizontally drilled pipe line river crossing application, by Titan Contractors of Sacramento, California, demonstrated that accuracies of better than one-half percent of range and a few tenths of one degree of bearing can be achieved by using refined techniques. The demonstration tests were done at ranges on the order of 100 to 200 feet but the method is capable of working at much greater distances.

Jan 1, 1978

By R. G. Nelson

This report covers investigations of the Bureau of Mines for the period of June 15, 1952, to June 15, 1953, on a research project for the Materials Laboratory, Wright Patterson Air Force Base, Dayton, Ohio. The primary purpose of this investigation was to make high-purity chromium-base alloys having room-temperature ductility and high-temperature strength. The Nonferrous Metals Branch of the Bureau of Mines, Albany, Oreg., has, during the past 7 years, developed on a laboratory scale a hydrogen treatment method for making high-purity chromium that can be fabricated into thin sheet and wire. This material can be bent at room temperature. The object of this investigation was to use this material to develop improved chromium-rich alloys for high-temperature uses.

Jan 1, 1955

By NRMR Bhargava

With the increasing use of lead-free solder alloys, low melting point alloy is often required due to the heat- sensitive parts or substrates in modern electronic devices. For such demand of low melting point, the nanostructure lead- free solder alloy, having excellent metallurgical characteristics and a melting point of <215oC, were developed by mechanical attrition of conventional lead free solder alloys (Sn-Ag-Cu, Sn-Ag and Sn-Cu). The decrease in melting point due to nanosize effect was calculated theoretically as function of particle size and the theoretical results were compared with experimental values measured by differential scanning calorimetry. The newly developed alloys have eutectic composition of Sn-3.5Ag-0.7Cu, Sn-3.5Ag and Sn-0.7Cu and the melting point depression found to be 5.10C, 4.10C and 6.20C when the bulk alloys reduced to 80 nm, 92nm and 96nm sizes respectively.

Jan 1, 2009

By H. Savasci, G. Yarim, J. S. Chung

As part of ongoing deep-ocean mining research, hydraulic transport systems as well as status of deep-ocean mining systems are reviewed in the aspects of manganese nodules and crusts from 8006,000-m depth. The emphasis of the investigation of hydraulic transport is placed on the shape effect of particles on the pressure gradients and flowrates. Series of tests are being conducted to study the lift characteristics of a 2-phasevertically upward hydraulic transport of 2 types of small solid particles in a PVC pipe of 1-in (2.54 cm) diameter: irregular-shaped silica sands and equivalent spherical glass beads. Pressure drops and mass as well asvolumetric flow rates were measured by electromagnetic(EM) flowmeter and mass flowmeter. The particle sizes used are 8-10 mesh. The results in turbulent flow range of 101045Re show that pressure gradients or friction factors are smaller for the spherical beads than the sands. The larger the concentration of the particles are, the larger the pressure gradients become. The larger the particle concentration is, the less the effect of particle shape on pressure gradients becomes. The shape effect is greater for the minimum particle transport velocities than for the settling velocities.

Jan 1, 1999

By Robert McClure, Frederic Leclercq, Ricardo Chavez

With significant vibration control and fragmentation challenges facing them, the CBS quarry (department of the Nord) successfully integrated a technical partner and mine to mill optimisation to deal with a difficult environment. For the last three years, CBS has been conducting a global production monitoring program similar to the mine to mill concept used in the mining industry. This concept consists of optimising the drilling and blasting while monitoring the effects on the downstream chain (vibration control, loading, hauling, crushing, plant output). Blast optimization is ensured by systematic control of the blast geometry (volumes, patterns, bench and face anomalies, drill deviation) and by the use of constant specific energy blasting. Constant specific energy optimises the work of the explosive in a blasting operation and, when combined with a high accuracy programmable electronic blasting system, reduces the impact of blasting on the environment and enhances blast performance. These techniques ensure consistent blasting results and hence improved site productivity. The improvements achieved have been identified thanks to an effective system designed to monitor the key production parameters.

Jan 1, 2007

By G. C. Sun

Rock mechanics properties, i.e. uniaxial and triaxial compressive strength, indirect tensile strength shear strength, Young&apos;s modulus, and poisson&apos;s ratio were collected for coal and related strata from 50 coal seams in 90 mines. The methodology of data organization and retrieval is described in details. The values and .ranges of those properties are also discussed.

Jan 1, 1993

By Paul M. Tyler

The outstanding trend in the graphite market is the fast-growing demand for cheaper qualities of graphite and the declining consumption of the more expensive varieties. The manufacture of graphite, crucibles for melting metals was one of the earliest applications of the-mineral and for many years constituted by far the leading source of demand. In later, years, however; and more especially since the Great War, the increasing demand for high-grade steel ingots and castings instead of enlarging crucible sales has permanently curtailed the domestic demand for crucibles because it has hastened the introduction of electric, oil or gas fired furnaces to replace the older types requiring pots to hold the metal during melting. While there has been a substantial increase in the use of graphite for miscellaneous refractories the total consumption for such purposes is too small to offset the shrinkage in demand for crucible making, and though it consumes the better and hence more expensive grades of crystalline flake graphite, it does not call so insistently for the still costlier Ceylon grades.

Jan 1, 1929

By Allan E. Martin

As part of a comprehensive investigation of tie mechanism of desufurization of iron and steel by slags, the Blast Furnace Studies Section, Metallurgical Division, Bureau of Mines, in cooperation with the Institute of Technology-, University of Minnesota, has made a study of the forms in which sulfur occurs in blast-furnace slag. This report presents data on the three sulfides most important in iron smelting, namely, ferrous sulfide, manganous sulfide, and calcium sulfide. The tendency of these sulfides to form colloids in the molten slag was determined by an examination of quenched samples with an ultramicroscope. Vogt5/ conducted experiments on sulfide silicate melts and examined synthetic blast-furnace slags in a partly crystallized condition. His conclusions were that FeS, CaS, and bins, or isomorphous compounds, such as (FexCay)S and (MnxCy)S, were precipitated Prom the melt, depending on the composition of the slag. In all specimens sulfides were visible and were spherical.

Jan 1, 1941

By D. Michael Holloway

The realignment of Interstate 880 replaces the double-decked (Cypress) viaduct collapsed in Oakland, California during the 1989 Loma Prieta Earthquake. The California Department of Transportation (CALTRANS) evaluated several pile foundation schemes for supporting the proposed structures. Structural support demands led to the selection of steel pipe piles (16-, 24-, and 42-inch-(406-, 610- and 1067-mm-)diameter), filled with concrete and steel reinforcement. Deep penetrations required through layers of very dense/cemented sands in some locations, caused serious drivability and pile integrity concerns. The need for large pile driving hammers and large diameter steel pipe piles pushed the engineers and prospective contractors well beyond the limits of local experience. Such questions as the feasibility of driving the pipes closed-ended through dense upper strata, and quantifying the effects of installation on the long-term capacities of the piles, led CALTRANS to develop a comprehensive pile test program to address the design and construction issues effectively. The results were furnished to prospective bidders on the production stages of the ensuing contracts.

Jan 1, 1996

Laboratory induced polarization measurements were made on representative samples of concentrated sulphide ores from three environments in New South Wales Comparisons were made with the membrane polarization exhibited by an argillaceous sandstone. The sulphide samples showed a strong polarization effect, the magmtude of whIch depended directly on the conductivity of tlIe pore electrolyte.

Jan 1, 1969

By James D. Noll, M. Eileen Birch

A monitoring method for diesel particulate matter was published as Method 5040 by the National Institute for Occupational Safety and Health (NIOSH). Organic and elemental carbon are determined by the method, but elemental carbon (EC) is a better exposure measure. The US Mine Safety and Health Administration (MSHA) proposed use of NIOSH 5040 for compliance determinations in metal and nonmetal mines. MSHA also published a rule making for coalmines, but no exposure standard was provided. A standard based on particulate carbon is not considered practical because of coal dust interference. Interference may not be a problem if an appropriate size-selective sampler and EC exposure standard are employed. Sub micrometer dust concentrations found in previous surveys of nondieselized, underground coal mines were relatively low. If a large fraction of the sub micrometer dust is organic and mineral matter, sub micrometer EC concentrations would be much lower than sub micrometer mass concentrations. Laboratory and ?eld results reported here in indicate the amount of EC contributed by sub micrometer coal dust is minor. In a laboratory test, a sub micrometer EC concentration of 31µg m 3 was found when sampling are spirable coal dust concentration over three times the US compliance limit (2mg m3). Laboratory results are consistent with surveys of nondieselized coal mines, where EC results ranged from below the method limit of detection to 18µg m 3 when size-selective samplers were used to collect dust fraction shaving particle diameters below 1.5µm sub micrometer EC concentrations were ?7µg m3. In dieselized mines, sub micrometer EC concentrations are much higher.

By L. W. Pommier, F. B. Brien, A. K. Bhasin

In the field of mineral processing, although many operations are applied to suspensions of ore particles in fluids, there is a lack of fundamental knowledge relative to the flow resistance encountered by immersed bodies moving through solid-liquid suspensions. Previously proposed equations, based on the Ostwald-de Waele (power-law) model for non-Newtonian fluids, are exam ined in the turbulent flow region relative to a number of pertinent variables and their effects on the movement of immersed bodies. As more knowledge is acquired in regard to the effects of suspension variables on the rheological properties, useful relationships may be proposed to allow predictions of conditions to achieve optimum results for engineering purposes. In the field of minerals processing, many operations are applied to suspensions of ore particles in fluids. The differential movement of solids of various sizes and densities in suspensions is of utmost importance to gravity concentration, wet classification, flotation, hydrometallurgy, and pipeline transport of solids. The subject is also of importance to other branches of engineering; for example, those involved with soil mechanics, ceramic slips, and oil-well drilling fluids. There is a lack of fundamental knowledge relative to the flow resistance encountered by immersed bodies moving through solid-liquid suspensions. The problems encountered in the direct application of the well-known Stokes and Newton&apos;s Laws to non-Newtonian systems have been examined in a previous paper.&apos; Equations were proposed based on the Ostwald-de Waele (power-law) model for non-Newtonian fluids. This present paper examines these equations in the turbulent flow region relative to a number of pertinent variables and their effects on the movement of immersed bodies. It is thought that, as more knowledge is acquired as to the effects of suspension variables on the rheological properties, useful relationships may be proposed to allow prediction of conditions to achieve optimum results for engineering purposes. The purpose of this paper is to make an initial assessment of the nature and magnitude of pertinent suspension variables. In order to avoid too voluminous a document, the examination of kinetics and mechanisms will be omitted at this time. THEORY A Newtonian fluid is defined as a fluid in which the stress is proportional to the rate of strain, 2 i.e.: H = viscosity; see Table I. for list of symbols The following equations are conventionally used to assess the motion of spherical particles moving under laminar and turbulent flow conditions through Newtonian fluids: When these relationships are applied in practice to suspensions, the liquid density is substituted by a composite suspension density, and viscosity is usually taken as that of the suspending liquid or an approximated "apparent viscosity." However, suspensions are non-Newtonian in character3 and thus, more than one viscosity parameter is required to describe their behavior. A number of models have been proposed for non-Newtonian fluids;2,4 among these the simplest is the Ostwaldde Waele or power-law model for incompressible fluids which for one dimensional flow may be reduced to:

Jan 1, 1970

By J Ward, B Rohrlach, B Rosero, J Silva, O Poma

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The Alpala copper-gold deposit is a recent, high-grade porphyry Cu-Au discovery located in the Imbabura Province of north-western Ecuador. The deposit lies along the crustal-scale Chimbo-Toachi Fault Zone within the Dagua-Piñon terrane, which is an oceanic plateau accreted to the South American convergent margin in the Late Cretaceous. The deposit is hosted by quartz diorite stocks that intrude andesitic volcanic breccias of the Oligocene to mid-Miocene San Juan de Lachas Formation. Miocene-age calc-alkaline plutonism is associated with porphyry Cu, Cu-Mo and Cu-Au deposits in southern and northern Ecuador. The Alpala deposit lies along a sector of the Miocene arc that has recently been underplated by the Carnegie Ridge seamount chain that induced shoaling of the subducted Nazca plate beneath northern Ecuador.Surface expressions of the deposit were recognised in May 2012 during follow-up of stream sediment anomalies, when outcropping sheeted and stockwork porphyry-related veins were discovered in Quebrada Alpala. The roots of a NW-trending, structurally-controlled lithocap were recognised over an area of 4.5 × 0.9 km. The remnant lithocap exhibits well-defined mineral zonation mapped by TerraSpecTM analyses on grid soil samples. Soil sampling, heliborne magnetic surveying and channel sampling defined initial drill targets.Seven diamond drill holes were completed in the year from September 2013. Drill hole CSD-13-005 intersected 672 m grading 0.93 per cent Cu and 0.91 g/t Au in high-temperature, inner propylitic and locally potassic-altered quartz diorite intrusions. Overlying hydrothermal clay alteration assemblages define the base of the lithocap. A NW–SE trending footwall structure defines the south-west margin of the deposit. Drill hole 5 intersected high-grade sheeted ‘B-type’ and ‘C-type’ veins (Gustafson and Hunt, 1975) that lie along the south-west margin of an 1100 × 500 m magnetic anomaly that is the focus of ongoing exploration.CITATION:Rohrlach, B, Poma, O, Rosero, B, Silva, J and Ward, J, 2015. High-grade porphyry copper-gold mineralisation in north-west Ecuador – The Alpala Cu-Au porphyry discovery , in Proceedings PACRIM 2015 Congress, pp 369–376 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By William A. Beck

This report describes the loading and transportation practices employed at the zinc-lead mines of The Eagle-Picher Co., Jo Daviess County, Ill., and Lafayette County, Wis. The report also gives a brief history of the Illinois-Wisconsin zinc-lead district and the operations of the company in the area. The diesel-powered, rubber-tired loading and haulage equipment is described and illustrated from the operational point of view only, and an analysis is made of the materials-handling system without going into health and safety Factors. The costs per ton of the various components of mechanical loading, underground haulage, underground crushing, and hoisting for fiscal year 1960 are tabulated.

Jan 1, 1964

By Natalya. N. Ankusheva

The problems of ore-bearing palaevolcanic structures in folded belts are actual because of their high productivity in nonferrous, ferrous and noble metals ores. Now relationships of location and conditions of formation for sulfide-massive and gold-bearing deposits are investigated very well in Urals. But carboniferous sulfide-barite mineralization, for example the barite veins in Arcaimsky palaevolcano are?nt studied enough now [3-5]. The purpose of this research is the studying of mineralogy and thermobarogeochemistry of barite from the hydrothermal veins. It will allow to determine the conditions of its formation and to compare it to the similar mineralization of others ore types.

Jan 1, 2006

The upper amphibolite-grade mctasediments of thc rinaroo area, North Queensland, form part of a regional aurcole to the large Tinaroo Batholith and are the stratigraphic equivalents of the Hodgkinson Formation of gencrally low metamorphic grade. There is no evidence of any lithological unconformity.The higher grade metasediments have a more complex deformation history than is typical for thc surrounding region and this may bc due to one or a combination of two factors; an additional strain componcnt associated wilh the intrusion of Ihe Tinaroo Batholith, or a more marked finite strain response to the overall regional stress field within hotter. more ductile rocks.Four deformational events can be characterized within Ihc Tinaroo Area. Close to Ihe Tinaroo Batholith D1 and D2, arc so strongly developed that they disrupl the continuily of Ihe original Iithological layering. In the aureole region, D1 is strongly overprinted and its original fabric intensity is obscured, but both D2 and D3 display a mappable decrease in intensity away from the granite margin. These three deformations occurred during Carboniferous or early Permian time. D4 is later and only patchily developed.The broad, moderate pressure metamorphic aureole surrounding the Tinaroo Batholith is a typical of the CairnsCooktown group of Permo-Carboniferous granitoids. which usually develop narrow, lower pressure contact aureoles. Two periods of metamorphism are distinguishable. The first reached peak temperatures somewhat greater than 520&#176;C, the second temperatures around 620-630&#176; C immediately adjacent to the granite contact.Several cale-silicate lenses containing scattered scheelite mineralization occur within the area. Scheelite appears to have crystallized at the same time as the cale-silicate minerals, its appearance coinciding with the intrusion of the Tinaroo Batholith. Unlike many &quot;skarn-type&quot; scheelite deposits, the scheelite-bearing cale-silicates are Fe-poor, with no positive correlation between total Fe and W.

Jan 1, 1982