Search Documents

By L. Kaufman

A range of processing conditions and compositions have been evaluated in order to optimize the properties of TiB2-(Ni,Cu) composites for application as a non-sparking tool material for use in coal mining operations. Fifty billets containing from 70 to 9S weight percent titanium diboride were hot pressed at 3000 psi between 2400°F and 2650°F. Samples which were cut from these billets were used to measure hardness, bend strength and impact strength so that composition/processing optimization could be effected. Eight compositions selected on this basis were evaluated by incendivity tests in order to choose the best composition. The best results were obtained for an 85 w/o TiB2-12 w/o Cu-3 w/o Ni composite hot pressed at 2650°F and 3000 psi. This material appears to be the best choice for fabrication of coal cutter bits to be evaluated in field tests.

Jan 1, 1973

By Jared M. Green

This paper presents the wall stabilization design and implementation for a 541 linear ft masonry and concrete gravity-type retaining wall flanking the west perimeter of a 7.37 acre parcel in Bronx, New York. This paper will discuss the results of static and dynamic stability analyses performed for the pre- and post excavation phases for the proposed 300 ft wide open-cut of up to 14 ft of contaminated soil below the toe of the retaining wall. The wall stabilization consisted of over 74 inclined drilled and grouted anchor dowels, and 55 tiebacks drilled and grouted to the underlying mica schist bedrock. Three over-lapping rows of jet grout columns were chosen as the foundation solution for the existing retaining wall. This paper focuses on the design, construction and performance of the jet grout curtain wall. The jet grout wall served three purposes: 1) underpinning and excavation support for the removal of contaminated site soils, 2) permanent hydraulic barrier, and 3) resistance against a deep seated failure within the thick clay layer present at the site. The originally designed jet grout wall had unexpected negative effects to the existing retaining wall. The jet grouting program was modified while the Observational Method (Peck 1969) was employed to keep wall movements to a minimum. This paper discusses the diagnostic methods used to determine the cause of retaining wall movement; the implementation of a remedial ground improvement program; the modification to the jet grout installation procedure; and the ultimate performance of the jet grout wall.

Jan 1, 2011

By Thomas Passlick

By means of further developed machines and techniques and with growing experiences in jet grouting, the challenge of this building method becomes more and more complex. To keep the concerning risks as low as possible, the requirements on the quality assurance continuously in­crease. The construction of a 37.0m deep seated slab for the Amsterdam metro station Vijzelgracht in marine clay represents such a complex task. This paper summarises the required measures of quality assurance. In particular a new hydraulic measuring device is introduced with which it was possible to detect the column diameter of 2.6m at a depth of 37.0m during the production process and with a very high accuracy.

Jan 1, 2006

By Jan E. Nesset, James A. Finch, Wei Zhang

"Bubbles are unquestionably the heart of the flotation process. Their size and combined surface area are largely what drive the recovery process. This suggests that plant engineers should be aware of where their plants are operating with respect to what is achievable for these key parameters. The paper presents a model of how the key operating variables of frother type and concentration, gas rate, altitude (above sea level) and viscosity affect the Sauter mean bubble size (D32) and bubble surface area flux (Sb). The results are compared to a set of plant measurements that demonstrate the benchmarking capability of the approach. A case study is used to link hydrodynamic change to improved metallurgical performance.INTRODUCTION At the beginning of the 20th Century the early practitioners of flotation were aware of the importance of understanding bubble behaviour (Rickard, 1916) but measurement of individual bubble and gas behaviour in the industrial environment was not possible due to a lack of adequate sensors. This situation was not rectified until three quarters of a century later with the advent of industrially-robust sensors developed, notably, at the University of Queensland’s Julius Kruttschnitt Mineral Research Centre (JKMRC) (Schwarz & Alexander, 2006) and McGill University (Gomez & Finch, 2002). What emerged was not the chaotic environment perhaps expected, but defined relationships between gas rate, gas holdup, bubble size and the total surface area of bubbles. These relationships could be defined by mathematical expressions and predicted from an understanding of the key process variables (Gorain, Franzidis & Manlapig, 1997; 1999) (Hernandez-Aguilar, Gomez & Finch, 2002) (Gomez, Cortes-Lopez & Finch, 2003) (Nesset, Gomez & Finch, 2007). The early JKMRC work focused on a large pilot cell (3 m3) installed in plant environments, while the McGill work was initiated on flotation columns (Finch & Dobby, 1990) (Xu, Finch & Uribe-Sales, 1991) and later adapted to industrial mechanical cells (Cooper, Scott, Dahlke, Finch & Gomez, 2004) (Dahlke, Gomez & Finch, 2005) (Nesset, Gomez, Finch, Hernandez-Aguilar & Difeo, 2005). Yianatos of Santa Maria University (Chile), a graduate of the McGill research team, carried the work to industrial settings in South and Central America (Yianatos, Bergh, Condori & Aguilera, 2001). The methods of gas dispersion measurement are now well accepted and most major research centres and flotation cell manufacturers have adopted the technology (Pyecha, Sim, Lacouture, Hope & Stradling, 2006) (Yañez et al., 2009) (Collins, Schwarz & Alexander, 2009)."

Jan 1, 2012

By M Bourke

Modern computers and software provide powerful tools for the geologist to construct reliable models of geological resources, and the mining engineer to produce accurate and workable mine plans. Over the years many people have developed a phobia of computers, especially for geological analysis, modelling and mine planning. This phobia is often caused by a lack of knowledge, poor training or a bad experience. The adoption however of computers for geological modelling and mine planning is now becoming mainstream. With the correct training, a good understanding of input data, and detailed knowledge of the required results, the phobia can safely be overcome to provide mining operations with increased productivity.

Jan 1, 1999

By W. L. Dare

This information circular is one of a series the Bureau of Mines plans to publish describing the methods and costs of mining uranium on the Colorado Plateau. The Temple Mountain mining district is unique among the uranium-producing areas on the plateau. This relatively isolated mining district is in Emery County, Utah, on the eastern flank of the San Rafael Swell, about 35 miles southwest of the town of Green River. The district lies just within the eastern escarpment of the San Rafel Reef - a rampart of rugged and tilted sandstone cliffs that encircles the highly eroded core known as the Sinbad Country. The presence of petroleum matter found associated with the ore deposits, the occurrence of uranium in various formations, and the structural deformation caused by collapsed features have aroused a great deal of geologic interest. Mine development on Calyx Flat is distinctive, in that the ore deposits are worked through 36-inch calyx-drill holes.

Jan 1, 1957

By Georgene Renner

At the beginning of the 1990s, Communism fell and signaled the end of the Cold War. The world rejoiced but also watched and waited to see how those countries would restructure themselves. The 1990 SME Annual Meeting was held at the Salt Palace Center in Salt Lake City, UT. The keynote session featured Alistair Frame, chairman of RTZ; Paul Queneau, professor of metallurgy at the University of Utah; and TS Ary, director of the U.S. Bureau of Mines. The SME Board of Directors voted to hire a Manager of Public Information and Education to be the GEM Program coordinator. This person was to collect and disseminate information that could be used by individual members and Local Sections to interface with government personnel and the general public.

Jan 1, 2007

By H. O. Hofman

At the Lake Superior meeting, September, 1904, Messrs. A. Gibb and R. C. Philp presented a paper entitled " The Constitution of Mattes Produced in Copper-Smelting,"' in which they concluded that ferrous and cuprous sulphides formed the chemical compound, 5 Cu2S, FeS. They arrived at this inference from the observed fact that a matte containing Cu,S, 90.4, and FcS, 9.6 per cent. (or, in round figures, Cu2S, 90, and FeS, 10 per cent.), did not contain any metallic copper, while one with more than 10 per cent. of FeS readily dissolved copper, and with less than this amount retained copper in mechanical suspension. Although they determined the melting-points of five mattes containing from 32.6 to 80.1 per cent. of copper, they did not draw a freezing-point curve, as the necessary apparatus was not available. A microscopical examination of 11 polished samples gave them a grayish-black field of very uniform appearance, except that five of the specimens showed the presence of metallic copper. The object of the present investigation was to supplement the above paper by drawing the freezing-point curve of the ferrous sulphide-cuprous sulphide series, and to see how the constitution could be further revealed by microscopical work. The results obtained lead to conclusions very different from those of Gibb and Philp. While their paper bears the date 1904, it was published only in 1906.2 In the meantime, Bolles3 had presented his paper, " The Concentration of Gold and Silver in Iron-Bottoms." The raw material which formed the basis of the research was a matte containing Fe, 61.68, and Cu, 11.20

Jan 1, 1908

By H Bibby

Initial analysis of Long Offset Time Domain Electromagnetic (LOTEM) data has traditionally been made in terms of early and late time apparent resistivities. By using more than one grounded bipole as a source, a tensor analysis technique analogous to the method used to analyse DC resistivity multiple-source bipole-dipole surveying may be formulated. We define the æinstantaneous apparent resistivity tensorÆ as the tensor that relates the total electric field vectors at each instant to the steady state (DC) uniform half space current density vectors due to each source. Instantaneous apparent resistivity tensors calculated for a 3D resistivity model suggest that profiles of LOTEM measurements across simple 3D structures can be used to create an image that reproduces the main features of the subsurface resistivity. Where measurements are distributed over an area, maps of the tensor invariants or the tensor ellipses at different times can be made into a sequence of images which provide a way of ætime slicingÆ down through the target structure.

Jan 1, 1996

By Enrique Ibarra, Manuel J. Mendoza

"Abstract: This paper describes the current state-of-practice for the design of cast-in-place drilled shafts in granular soils under axial loading, addressing recent advances that take into account the surrounding soil grain size distribution and their behavior. The important role of the gravel content in the shaft response under axial loading is emphasized. Usual design approaches in Mexico are described, and the results of load tests from different sources are discussed. The analysis emphasizes the primary contribution of the lateral area of shafts to their axial bearing capacity, raising doubts regarding the common local idea of “point bearing shafts”. Finally, some lines of research are noted to permit advances in the important field of deep foundations. 1 INTRODUCTIONIn Mexico, cast-in-place drilled shaft foundations are widely used to support various structures in the west area of Mexico City, where alluvial and volcanic deposits predominate. Deep foundations are also used in modern construction works located in other major cities of Mexico. In fact, the use of drilled shafts for tall buildings and overpasses in the center of Guadalajara as well as in transportation works related to the Metro and roadways in Monterrey is well known. It is worth mentioning that these same structures have been applied in road bridges throughout the country.Procedures for pile construction in Mexico have been basically the same for the past 20 years (Paniagua et al., 2005); however, modern equipment has been incorporated into the construction industry, including innovations in sludge-drilling technology, control and the quality of the castings. In addition, novel and efficient procedures such as construction with continuous auger displacement piles have been implemented (Auger Cast in Place, ACP) and have begun to be used locally with success (Schmitter and Paulin, 2006).However, it can be argued that the technological developments that have resulted in more efficient construction procedures have not included a breakthrough in the full understanding of the phenomena or basic mechanisms of load transfer from piles to the surrounding subsoil and therefore in supported, tested and practical design methods. This is particularly true when seeking to determine the unit side shear strength of shafts drilled in granular media with gravels, where it has been observed that the commonly used calculations developed for sands underestimate the load-bearing capacity by frictionin a most important way. Due to the above reasons, it seemed appropriate to present in this paper a review of the current stateof- practice in Mexico for the design of cast-in-place drilled shafts, particularly in granular media, highlighting some recent advances and research that takes into account the grain size distribution and behavior of granular soil."

Jan 1, 2014

By Scott Rosenthal, Kyle Murphy

This paper discusses the trials and tribulations of obtaining Velocity of Detonation (VOD) readings in small diameter blast holes in an underground mine. Montana Technological University (Montana Tech) obtained a time-domain reflectometer (TDR) type VOD monitoring unit. Purchase of the VOD monitor was justified on verifying explosives performance used in Montana Tech’s practical underground mining class and provide a teaching aid for the school’s rock fragmentation class. Before demonstrating the unit to students, we figured we better learn how to use it first so we give the students an appropriate experience. Our first learning was in obtaining the correct coaxial cable for the VOD monitor and how to properly terminate the cable. Once the cable was on-site and terminated, VOD testing could commence. Use of the VOD monitor was tested underground in small diameter holes (1.5-inch, 38 millimeter) pneumatically loaded with ANFO. After a few failed trials, and follow-up discussions with the supplier, VOD readings were obtained for the ANFO loaded holes. Additional readings were obtained for a pre-split product and detonating cord to satisfy our curiosity that the unit was performing as specified by the manufacturer. This paper will share our learnings in the hopes that others can benefit.

By Klaus Stoss, Bernd Braun

The sinking and lining of a large mine shaft with 8.0 m i.d. and 1,133 m total depth is described in detail. The ground freezing method was applied to safely sink the shaft through unstable, waterbearing strata. Following a brief introduction to the geological and hydrological conditions and the owner's shaft requirements, is the general technical concept to sink and line the shaft. Particular emphasis is put on the lining system which has to provide stability and absolute watertightness for the lifetime of the shaft, even though mining takes place in its immediate proximity. Machinery and equipment used to execute the work are mentioned and commented. Furthermore, the excavation and lining of the large filling stations using rock anchors and shotcrete are described. Details on performance rates are given.

Jan 1, 1983

By J. Lipp

The lion share of lithium produced globally originates from South American salars. The standard operation for lithium production utilizes an array of evaporation ponds. This process consume vast areas and is either very slow when relying on solar evaporation - roughly 18 months of residence time; or with very high energy consumption since over 90% of initial water volume needs to be evaporated. A new technology, based on solvent extraction was developed. Results indicate a distribution coefficient up to 30, and selectivity greater than 1,000 towards Na extraction. The loaded solvent is stripped using a strong mineral acid, and the product solution is the lithium derivative of that stripping acid. Utilization of this new LiSXTM technology results in reducing the area needed for a commercial plant as well as reduces the residence time. In addition applying different stripping acids can diversify the product line of such facility.

Jan 1, 2014

By K. C. Dean

During the course of the investigation of manganese mineral occurrences in the western United States, the Bureau of Mines collected several lots of ore' from properties in the vicinity of Winkelman, Ariz. As none of the ores would be marketable directly, an investigation was made to determine their amenability to concentration by ore dressing. The Geronimo group of claims is in Pinal County, 8 miles west of Winkelman, Ariz. The manganese oxides occur as cementing material in ore zones of conglomerate. Representative samples of a 2-ton lot of ore cut from outcrops of two lenticular deposits were laboratory-tested. Two 1-ton samples from the Benningfield property were similar in physical characteristics but differed in grade. This claim is 11-1/2 miles south of Winkelman and about 1 mile west of the San Pedro River on the south side of Putman, Wash. The manganese minerals occurred as nodules and lenses, replacing limestone, in a capping over a dark, igneous dike. The North Star group consists of five claims on the west side of the San Pedro River 14 miles south of Winkelman. The ore consists of a low-grade, manganese oxide-calcite occurrence interspersed with stringers of higher-grade material and is present as filling in a fissure zone in porphyry. Two samples were obtained by the examining engineer; one sample represented run-of-mine material, the other represented ore from the vein that could be hand-sorted or selectively mined.

Jan 1, 1952

By Robin B. Dill, Mark Pelletier, Daniel J. Dobbels, Subodh Bhaumik, Daniel J. VanRoosendaal

Although primarily cut-and-cover excavations are required for replacement of the existing elevated I-93 interstate highway through the heart of Boston for the Central Artery/Tunnel (CA/T) project, some mined tunnel construction was also undertaken. The mined tunneling conducted was the 22-m-wide northbound roadway structure which passed below a 20-m-deep operating underground subway station that was built in 1913. The innovative underpinning scheme used to support the subway station during construction resulted in the successful mining beneath the subway station with negligible vertical settlement. Two grouting galleries were carefully mined below the subway structure, and pre-grouting of the granulary, pervious glacial soils and weathered bedrock was carried out from these galleries. The reinforced concrete walls of the underpinning structure were constructed within three stacked drifts that were sequentially mined below each grouting gallery. After 11 cross adits were mined between the grouting galleries, cast-in-place post-tensioned girders that spanned between the stacked-drift walls were constructed to support the subway station. The stacked-drift walls also provided lateral support for the 22-m wide by 29-m long by13-m high opening beneath the girders.

Jan 1, 2001

By R. A. Hatch

The United States depends mainly on foreign imports, principally India, for an adequate supply of sheet mica suitable for its many uses in the electrical and electronics industries. Sheet mica has, in fact, played an indispensable role in developing these industries,4/ and, in turn, the products of these industries (radio, radar, electric motors, and many others) have become indispensable to the military forces. Because or these conditions, sheet mica in its better qualities long has been classified as a strategic and critical material, and from this stems the wide-spread interest in substitute materials of which synthetic mica is one potential type. The United States Departments of the Navy and the Army entered into a cooperative agreement with the Bureau of Mines in 1947 to study ways and means of synthe-sizing and growing mica crystals. This is one of a series of reports5/ that describe the results of this program.

Jan 1, 1956

By George S. Rice

"INTRODUCTION During the past 4 or 5 years the frequent occurrence of bumps in coal mines of the Cumberland field, in Harlan County, Ky., and Wise County, Va., has caused much apprehension among miners and mining officials of that region.These bumps have caused many deaths and injuries, and have been increasing in frequency. Eight men were killed and a number injured by bumps in the first 4 months of 1934. Their unpredictable occurrence and the usual absence of any preliminary warning tremors or sounds, such as ordinarily precede a large fall of roof, cause fear of other bumps and impair the morale of mine workers.Acknowledgments This report on bumps in coal mines of the Cumberland coal field of Kentucky and Virginia is based on an investigation made at the urgent request of .the Harlan County Coal Operators Association, through James F. Bryson, director of safety of the association, to the Director of the United States Bureau of Mines, following a series of disastrous bumps in. Harlan County, Ky., and Wise County, Va. The request was granted and the writer detailed to undertake the investigation, which was made in June 1934.The officials of certain operating companies in the Cumberland field gave every facility for examining the conditions accompanying bumps in their mines. The writer is most grateful to them for the courtesies shown; to J. F. Bryson, to J. F. Davies, district engineer, Safety Division, U. S. Bureau of Mines, who accompanied the writer throughout his trip to the vari¬ous mines and gave him much assistance and detailed information regarding the occurrence of bumps; and to Dr. David White for reviewing the geological descriptions,Definition of Bumps ""Bumps"" are phenomena comparatively rare in the coal fields of the United States and, for that matter, in the coal fields of the world, because for their occurrence certain exceptional natural conditions are required strong, massive strata of sandstone or conglomerate above the coal and a fairly strong floor, as will be described in detail later."

Jan 1, 1935

By A. W. Dougall, T. M. Mmola

"SynopsisThe global resources and commodities market has become highly competitive. While southern Africa’s abundance of minerals resources is still unrivalled, it has lost considerable dominance in terms of production output. The sustainability of southern Africa’s mining industry is increasingly becoming dependent on its ability to manage the performance of its operations well. A valuable tool for monitoring and managing performance is the use of key performance areas (KPAs) – which are those areas of performance that are reflected explicitly or implicitly in the vision and strategies of an organization and reflect the critical success factors of the organization. This paper is a review of key performance areas in the southern African mining delivery environment. The KPAs discussed in this paper have been identified by comparing KPAs of the several mining houses engaged in surface mining operations in southern Africa and then extracting those KPAs that are common to most of them. Although the authors support the view that each organization should develop KPAs to specifically fit its needs, the study reveals that five KPAs – safety and health, costs, product quality, fleet management, and delivery should form a default list that covers the key areas that any organization should consider when choosing KPAs. KPIs are those subsets of KPAs that we measure in order to manage KPAs.IntroductionThe global resources and commodities market has become highly competitive. While southern Africa’s abundance of minerals resources is still unrivalled, it has lost considerable dominance in terms of production output. The sustainability of southern Africa’s mining industry is increasingly becoming dependent on its ability to manage the performance of its operations well. A valuable tool for monitoring and managing performance is the use of key performance areas (KPAs), which are ‘those areas of performance that are reflected explicitly or implicitly in the vision and strategies of the organization’ (Barker, 1997). The terms KPA and KPI (key performance indicator) are often used interchangeably – whether correctly or erroneously is debatable. KPIs are ‘quantifiable measurements, agreed to beforehand, that reflect the critical success factors of an organization’ (O’Neill, 2007). Each KPA probably has multiple KPIs associated with it."

Jan 1, 2015

By Melvin I. Esrig

Lime Cement column stabilization of soft clay and sand in Salt Lake City, Utah and in San Francisco California is described and discussed. Stabilization permitted the construction, in a single stage, of a 14 m MSE wall on "medium" clay in Salt Lake City. It was used to mitigate the potential for liquefaction in San Francisco and to stabilize the Young Bay Mud beneath the BART extension to San Francisco Airport. These applications are described and the field measurements of performance are reported.

Jan 1, 2000

By R. L. Andrew

The southwest Pacific has produced at least four of the world’s premier porphyry copper-gold deposits, and the current level of exploration is likely to produce even more. An appreciable amount of gold is being produced with this copper, with obvious economic advantages. Gold content, in addition to their large size, makes the southwest Pacific’s porphyrycopper-gold deposits very attractive exploration targets. The recognition of telescoping and overprinting of porphyry systems has produced a greater awareness of the likely surface expressions, in particular the significance of advanced argillic lithocaps in porphyry exploration. The recognition of the spatial and genetic association of porphyry copper and epithermal gold systems (Sillitoe, 1972), as in other parts of the world, has had important implications for exploration in the Asia Pacific region.

Jan 1, 1995