Search Documents

By John D. Foulkes

An investigation is made into whether commercially available equipment can be used to engineer effective emergency warning systems for underground coal mines. Discussions with members of the Bureau and the Mining Enforcement and Safety Administration established that the preferred system should operate over the existing Pager Phone twisted pair, and broadcast an audio alarm. Applicable equipments such as voice band tone signaling equipment, alarm sounding equipment, mine telephones and complete alarm systems from over thirty manufacturers are listed. Factors affecting the range over which an alarm could be detected in representative mine situations were studied. These included (a) the subjective masking effects of typical background noise found in mines, such as that due to continuous miners (b) the attenuation of sound in mines (using both a theoretical and experimental results) and (c) the attention-getting qualities of different sound for miners. Audio alarm systems meeting the requirements can be installed and representative systems are described.

Jan 1, 1977

By Ta M. Li

How will phosphate producers in southeastern Idaho fare with growing governmental regulations and environmentalism of the late 1970's? With a similarity that is reminiscent of the battles between the coal industry and environmental-conservation groups earlier in the decade, Idaho's future growth and a nation's need for phosphate fertilizer products remain uncertain. The catalyst that brought the issue to the forefront was the preparation of an Environmental Impact Statement (EIS) addressing the development of phosphate resources in southeastern Idaho. Although the final EIS was published in August 1977, resolution of rational and orderly growth in this potentially vital region remains stifled as Secretary of the Interior Cecil Andrus virtually "sits" on it.

Jan 1, 1978

By William S. Gardner

It is certainly an honor to have been invited to address the Deep Foundation's Annual Meeting on such a vast and weighty topic as "Present to Future Design Considerations of Deep Foundations." Acknowledging the enormity of this 30-minute assignment, I hope to at least scratch the surface of the topic deep enough to generate some thought and reflection. Design considerations, be they current or future, bring to mind a number of important subtopics which comprise the design process. As shown by Figure 1, a flow chart of this process describes, in general terms, the sequence of a deep foundation design.

Jan 1, 1991

By Xinquan Zhou, Rudolf E. Greuer

MFIRE, written in Fortran 77, is a computer program for ventilation state simulation in the steady state or transient state condition. It can be applied for the calculation of normal ventilation system planning or the analysis of the dynamic state variation in a ventilation system under thermal or mechanical disturbance. The state simulator MFIRE is a useful tool for mine fire fighting. In the case of a mine fire, mine ventilation engineers want to get some help to obtain more information, such as what is happening in the underground mine and how to control the mine fire, for correct decision making. By use of program MF'IRE, forecasts can be made on the variation of airflow, temperature, and contaminant distribution in a ventilation system during a mine fire. The paths which the contaminant takes at each time interval can be traced. The program MFIRE can be of assistance in the preplanning of escape routes. It can also be helpful during a mine fire emergency and mine recovery operation. Besides of offering the information of state simulation during a mine fire, MFIRE can be applied for state control by pretesting the suitability of the selected state control measures. It is to simulate the effects of the state control measures on the airflow distribution of a dynamic ventilation system. The testing result can be used for fire fighting in a similar real case of a mine fire. By employing empirical methods or a qualitative analysis like Budryk approach, ventilation engineers can choose different combinations of locations and sizes of control devices as samples of state control for an underground mine fire. Program MFIRE can simulate the different combination samples, that consist of a certain mine fue, the corresponding different control measures, and obtain the control effects. After the different control results are compared, the state control measure, which creates the best effect among the different state control measures, will be chosen for that fire case. When a mine fire, which is similar to one of the pretested cases, breaks out, the corresponding choice of the state control measure is applied to the ventilation system. It means that the simulator MFIRE has the function of indirect state control [10]. To achieve the above two functions, state simulation and state control, the mine ventilation system condition, sometimes, should be changed in a wide range to meet the requirement of the fire fighting. These wide system condition changes, such as adding operating fans, stopping or reversing fans, changing fan characteristics, adding regulators and making airflow shortcuts are represented in the time table of the input data set When the data files are changed in a wide range, however, an iteration divergence and some other computing errors in the distribution of airflow, temperature, and contaminant may occur. More serious logical programming and flexible selection on the algorithms are wanted to meet the request of the different data sets, to achieve correct state distribution simulation and improve the iteration convergence. To enhance the reliability and common suitability of program MFIRE, it is necessary to make investigation, analysis, and modification for the formal versions of MFIRE. The version 1.29, permitting dry .calculation, and versions 2.01/v2.0, permitting dry and humidity calculation, are widely applied

By W. A. Naismith

On 16 July 2004, at 07:10 a collapse of about 1.8 million m3 (about 4 ½ million tons) took place on the north wall on Nchanga Open Pit. This collapse was the result of a developing instability that was first identified when the benches in this area were exposed during September 2002. The NOP geotechnical and survey departments closely monitored the development of the failure. Control measures were implemented to reduce risk to men and equipment. These measures were continually improved and adjusted in reaction to observations and changing conditions. The purpose of this paper is to describe in detail the monitoring results that were obtained both by traditional methods and the novel slope stability radar system (SSR). Difficulties encountered in establishing critical deformation levels and deformation rates that can be used to predict the onset of collapse are described. Details of the monitoring and control measures, which led to the successful completion of mining in the area, are also described in this paper.

Jan 1, 2005

By S. K. Mathur

This report identifies all the possible activities, variables and factors that contribute to the surface subsidence process over room and pillar workings. These factors are responsible for mine instability and collapse that ultimately transforms into surface subsidence. Such a failure mechanism is initiated by the failure of the mine floor bed and or the failure of the pillars or the failure of the roof after second mining, which eventually brings down the roof. The individual responses of the pillar, floor and roof rocks to the mining induced stresses and the complex interaction between these components can't be attributable to any single factor. Also, no attempt has been made to quantify the significance of each of these factors and relate to the ground subsidence due to the lack of field data. The discussion here is centered primarily on the first mining though second mining is mentioned very briefly,

Jan 1, 1982

By F. D. DeVaney

The low-grade deposits of manganese ores along the Missouri River near Chamberlain, S. Dak., are known to contain one of the largest reserves of manganese in the United States. Manganese occurs as concretionary nodules ranging in size from 13 inches in their longest dimension to particles finer than 65-mesh. The nodules are embedded in soft, wet shale, which contains little manganese. The removal of nodules from the low-grade shale is a simple mechanical -problem; the question is primarily to determine the lowest-cost method of separation. This report purposes to present data acquired by experimenting with samples of the ore, which form a basis for suggesting methods of concentrating manganese nodules.

Jan 1, 1942

By F. D. DeVaney

The low-grade deposits of manganese ores along the Missouri River near Chamberlain, S. Dak., are known to contain one of the largest reserves of manganese in the United States. Manganese occurs as concretionary nodules ranging in size from 13 inches in their longest dimension to particles finer than 65-mesh. The nodules are embedded in soft, wet shale, which contains little manganese. The removal of nodules from the low-grade shale is a simple mechanical problem; the question is primarily to determine the lowest-cost method of separation. This report purposes to present data acquired by experimenting with samples of the ore, which form a basis for suggesting methods of concentrating manganese nodules.

Jan 1, 1942

By D. G. Krige

For the purpose of determining confidence limits for ore grade estimates, an extensive simulated data base was used, which included 1728 ore blocks with ‘actual’ grades and the corresponding estimates based on ordinary and simple kriging. The practical results show that conditional unbiasedness is essential and that acceptable confidence limits can then be set using Normal theory for the simulated error distribution based on the logarithms of the ratios of ‘actuals’/estimates with a variance related to the kriging variance. The mean of the data used to prepare the variogram and the estimated block grade are to be used properly in this approach. A practical analysis was also done of the actual point and block data from a very large mined out Carbon Leader area. The distributions of the actual grades for two levels of block sizes with different levels of variability were fitted using three models, ie. 2-. 3- and compound-lognormal. The trends of tonnages, grades and relative profits for a range of pay limits, as well as the usual tonnage-grade curves, show a practical insensitivity for the choice between the three lognormal models considered.

Jan 1, 2003

By Richard Mcivor, Largo Albert

"Inco Limited has operated aluminum mine shaft conveyances since 1968. Aluminum conveyances are used where the hoisting in system requires lightweight conveyances to maintain the hoist rope safety factors and mine hoist rope pulls as dictated by government regulations. Inco Ltd. currently has 20 skips (including spares) operating in the Ontario Division mines. The main problems encountered are with galvanic corrosion between dissimilar metals and metal fatigue. This paper will highlight some of the problems encountered and illustrate methods utilized to overcome the problems and improve the conveyances performance.IntroductionAluminum mine shaft conveyances have been in use at Inco Limited's various Sudbury district mines since 1968. All of the conveyances currently in use are skips used for hoisting mine ore and rock. Inco had an aluminum quick change Kimberley-type skip and cage in operation at its Totten Mine in the early 1970s, but this mine is no longer in operation and no further comment will be made.The primary reason why aluminum conveyances are chosen over conventional steel conveyances is because of their light weight. Typically an aluminum conveyance will weigh about 60% to 70% of a steel conveyance of similar design. The lighter weight conveyances will allow higher payloads to be used and still maintain the statutory hoist rope factors of safety. It must be remembered that increasing the payload will increase the power required to raise the load and the hoist will have to have the necessary horsepower for the increased payload or the system will be overloaded.The front dump (Rola-chute) skips are of the bail-less design, i.e. the box structure also supports the load and has the shaft guide shoes attached directly to the side of the box structure. The Copper Cliff North Mine and South Mine skips have a joint in the centre of the conveyance and are installed in the shaft in two sections and connected with pins. This feature allows very long (42 ft) skips to be used in areas where a one-piece bail-type conveyance could not be installed. It is not practical to make sectionalized bail-type conveyances"

Jan 1, 1988

This report, the third in an annual series, outlines recent trends and developments in the minerals industry. Discussed are new methods, equipment, techniques, and systems used to more, effectively extract and process minerals and fuels. Environmental considerations, reduced ore grades, and the related increased quantities of material handled were the dominent concerns of the minerals industry in 1972. Productivity increased in most mineral commodities as equipment became more mobile, versatile, and sophisticated. Increasingly, equipment designs incorporated health and safety features. There was considerable interest in the field of energy and in pollution-free metallurgy processes.

Jan 1, 1973

By Russell J. Gartrell

This report describes the engineering feasibility and economic advantages of using a steep angle conveyance (SAC) system in conjunction with medium and large draglines to transport spoil in a typical Western Coal Mine. The SAC system, including a receiving hopper, a steep angle conveyor and a sticker/spreader, is capable of processing overburden material at the rate of 7,000 tons/hr. The unique feature of this system is the steep angle conveyor which transports the overburden material from the pit bottom to the top of the spoil at angles to 45 degrees. Compared to other means of cross-pit conveyance considered during this study, the SAC system offers the advantage of easier operation, lower conveyance cost and greater mobility. The results of this study have shown that integration of the SAC system into both established and planned new mines would improve the overall mining operation, expand the operating capability of existing equipment and reduce mining end reclamation cost.

Jan 1, 1977

By S Hapugoda, J R. Manuel, M J. Peterson

Microindentation testing using the square–pyramid–shaped Vickers indenter is a well-established technique to determine the microhardness of minerals and materials. However there is a paucity of published microhardness data from Fe ore samples. It is acknowledged that an iron ore’s particle mineralogy and texture is critical to its processing properties, and it is therefore considered that the microhardness of different mineralogical/textural types may also relate to these properties. Mineral microhardness potentially provides inputs to the modelling of breakage characteristics during comminution, as well as the relationship between mineral chemistry and microhardness, and mineral microporosity and microhardness. Microhardness can be determined as single crystal microhardness, for more coarsely microcrystalline samples, or as ‘aggregate microhardness’ for cryptocrystalline or finely microcrystalline samples.Variations in the texture and mineral chemistry of common Fe ore minerals (eg martite and microplaty hematite, ochreous and vitreous goethite etc) are well established and this study provides microhardness data on different textural forms of Fe (oxyhydr)oxides from a variety of different Fe ore deposits. The data indicated that in general, the mineral grain size, microporosity and texture were the main influences on Fe (oxyhydr)oxide microhardness. There were no apparent systematic variations between microhardness and minor element mineral chemistry, with the possible exception of Al content in goethite (for goethites with Al content >0.5 wt per cent), and for goethite total element contents >90 wt per cent (determined by electron probe microanalysis, EPMA). Higher Al concentrations and lower total element concentrations in goethite EPMA analyses correlated with lower goethite microhardness. Microporosity and grain size were more important than texture to hematite microhardness. Different textural forms of dense hematite (eg martite, recrystallised interlocking hematite and specular hematite) with similar grain size exhibited comparable microhardness. Microhardness values for hematite and hydrohematite with little or no evident microporosity were also similar, whereas more porous forms of martite, microplaty hematite or hydrohematite exhibited lower microhardness.CITATION:Peterson, M J, Manuel, J R and Hapugoda, S, 2017. Microhardness testing of hematite-goethite Fe ores – implications for their textural characterisation and geometallurgy, in Proceedings Iron Ore 2017, pp 319–330 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By James W. Marold

Tunnel and shaft plugs have been designed to assist in construction of new and rehabilitation of existing tunnels and shafts. Tunnel plugs have been used to provide construction access for side by side tunnels, separation of raw and treated water, and to allow operation of one tunnel during construction of a nearby tunnel. Shaft plugs have been used to seal up surface openings to tunnels and to prevent seepage of water to the surface through adjacent tunnels or shafts. The design construction details of tunnel and shaft plugs are provided. Typical examples of tunnel and shaft plugs are provided.

Jan 1, 2008

By P. Marcotte, G. LeBlanc, S. Ouellette, J. Boutin

"To characterize noise and vibration sources of different types of mining equipment used in underground mining, the authors performed a study in eight Quebec mines on 28 pieces of equipment. This paper presents the procedure followed to select the equipment to be evaluated, and the low-cost acquisition system developed to perform multichannel time-domain data acquisition in harsh environments. It also presents the results obtained for the noise level produced by the equipment and for handarm and whole-body vibration exposures.RÉSUMÉ Dans le but de caractériser les sources de bruits et de vibrations de divers équipements miniers utilisés sous terre, les auteurs ont étudié 28 équipements dans huit mines du Québec. L’article présente la procédure suivie pour choisir les équipements à évaluer ainsi qu’un système multicanal à faible coût développé pour acquérir des données dans des environnements difficiles. Il présente aussi les résultats obtenus pour les niveaux de bruit produit par les équipements et pour les expositions main-bras et du corps entier aux vibrations."

Jan 1, 2015

By David W. H. Ellis

This presentation will discuss over 2 dozen past, present and future oils sands projects in Alberta. The very early projects as well as the most recent along with the ones that never got off the ground and the ones in production are all included. For each, the following will be given (where known): owners, location, type (mining/SAGD/refinery), production, capital budget, spent to date, status. Some overall impacts will be discussed.

May 1, 2004

IN this paper an attempt is made to describe the sluicing operations on the tin fields of north-eastern Tasmania. No claim is made to completeness, for much of the ground has already been covered, and nothing is to be gained by needless repetition. On this account some portions of the subject have obviously received but attention in order that others may be rather more fully dealt with; for instance, referring to the accuracy of various methods of valuing alluvial deposits, particulars of efficiencies, and water duties on both overburden and drift; also, the system of recording water distribution, &c. The plans of the tin-streaming shed, sluice and feed race, and overburden tail-race represent types of the most modern design.GEOLOGY. The principal alluvial dcposits being worked at the present time are situated either in the ancient or modern bed of the Ringarooma River or its tributaries. This river flowed in a north-easterly direction, receiving numerous tributaries on either bank...

Jan 1, 1910

By S. J. Jung

Determining the correct combination of mix components and water for high-density paste backfills with the transport and deposition properties necessary in a mining operation is a difficult task. Rheologic properties cannot be determined without conducting full-scale pumping tests, and data from existing tests are very limited. The following presents the findings of investigations undertaken to determine if paste backfill rheology can be determined using existing techniques and which mix and system variables have the greatest influence on transport pressure loss. Data from lab-oratory-scale pumping tests were used to produce a rheologic model of flow behavior for comparison, and a statistical analysis was conducted to determine the most significant factors affecting transport pressure loss.

Jan 1, 1994

By D. J. Young

Alloys used at high temperature must resist both creep and corrosion. Design for corrosion resistance is based on the formation of a slow-growing, protective oxide scale by selective oxidation of an appropriate alloy component, usually chromium or aluminium. A successful scale will exclude other corrodents, notably carbon, which can otherwise cause extremely rapid corrosion at high temperatures. Selective oxidation of an alloy component necessarily lowers the concentration of that metal in the alloy subsurface region. Under thermal cycling conditions, mechanical damage to the scale leads to renewed oxide growth and accelerated alloy depletion. Eventually, a point is reached where diffusion of a corrodent into the alloy becomes competitive with the outward diffusion of alloy metal to repair the protective scale. Two examples of alloy failure by carbon attack are considered. In the steam cracking (pyrolysis) process, centrifugally cast tubes of heat-resisting alloy are exposed to a gas stream of hydrocarbon and steam, at a carbon activity of unity. Formation and repair of the surface chromia scale causes alloy depletion, Kirkendall void formation, and subsequent internal precipitation of chromium-rich carbides. Their formation makes chromia scale formation much more difficult, and generates internal stress. Eventually, the tubes fail by creep rupture. In other processes (e.g. steam reforming, heat treatment), synthesis gases are supersaturated with carbon at intermediate temperatures. Once the alloy's protective scale is breached, carbon attacks the depleted substrate. In the case of ferritic alloys, it forms a surface scale of Fe3C. As this scale thickens, the supersaturated carbon precipitates as graphite within its outer regions. The resulting volume expansion causes disintegration of the cementite in a process known as metal dusting. In the case of austenitic alloys, no metal carbide is formed. Instead, carbon dissolves in the depleted metal to diffuse inward and precipitate as graphite within the metal matrix. Again, volume expansion causes disintegration of the alloy, and metal dusting results. Dusting occurs at an extraordinarily rapid rate, and leads to failure by section loss or even penetration.

Jan 1, 2013

By W. C. Blanchard

Time Domain Reflectometry (TDR) is a remote sensing technique using active backscatter. This technique is applicable to the testing for faults and multiple partial faults on cable. The battery operated hardware developed on this con¬tract has tailored this technique for testing of mining equipment trailing electrical cables. The processing of-t-he back-scatter is accomplished using a microprocessor. The visual output from the hardware to the operator is; the type, magnitude and distance to the cable fault in a numerical format. This greatly simplifys the use of this techniques for the operator.

Jan 1, 1980