Search Documents

By J. M. Riley

This report summarizes Bureau of Mines experiments in purifying sulfate leach liquors, which were prepared from low-tenor beryl concentrates by modifying the Degussa process. The leach liquor was prepared from a beryl concentrate containing 2.7 percent BeO by (1) sintering the beryl concentrate with limestone in a rotary kiln at about 1,150° C. and by (2) treating the sinter first with sulfuric acid and then with water to form and extract beryllium sulfate. About 80 percent of the beryllium was dissolved. The resulting leach liquor contained 2.4 grams of BeO, 20 grams of Al203, and 6 grams of Fe203 per liter. The laboratory solution contained much more aluminum and iron than a solution derived from treating 10 percent BeO concentrate, which is the standard raw material used by industry. Tests were made to determine the behavior of the solution toward alum purification and limestone neutralization both of which were employed industrially in conventional Degussa procedure.

Jan 1, 1962

By H. E. Powell

A laboratory investigation was conducted by the Bureau of Mines to study the magnetic characteristics and to measure the magnetic susceptibility of the mineral siderite. All susceptibility measurements were made by the method of Gouy on powdered samples and at room temperature. Specific susceptibilities of samples from 15 different locations, domestic and foreign, were determined. Values ranged from 66 to 103 (10-6) cgs electromagnetic units. The relation of susceptibility to mineral composition is discussed in this report. The specific susceptibilities of 76 minerals are tabulated in an appendix.

Jan 1, 1963

CSA mine, which is a deep level copper operation, located 12 km north of Cobar, NSW, currently uses a top down stoping method, utilising cemented hydraulic backfill (CHF) to fill and stabilise the stoping void thus assisting the extraction sequence. The stope sequence then requires development back through the CHF stope so that the necessary infrastructure for the subsequent stoping, such as raise bore pads can be sited. The primary and secondary support installed in the CHF consisted of 100 mm thick fibrecrete from floor to floor with 7 + 2.4 m long resin support tendons installed at 1.5 m ring spacing. This support system relied on the resin achieving a quality bond with the CHF, and also the fibrecrete developing early structural strength due to the use of an accelerator. In addition to the delays in the excavation turn around time, it was felt that a superior support system could be designed. Such a system was designed; risk assessed, tested underground, and trialled in selective CHF digouts, and eventually signed off as the chosen support method in CHF digouts. This paper discusses the change from a passive support system used in CHF digouts to an active support system using Swellex bolts and weld mesh, which has provided an active support system, that is superior, faster to install, reduced the excavation turn around time and is overall a cheaper support system.

Nov 25, 2010

By Terry R. Neumann

A mineral survey of the 23,760-acre Abert Rim Wilderness Study Area (OR-1-101) was conducted by the U.S. Bureau of Mines in 1986 at the request of the Bureau of land Management in order to evaluate its identified mineral resources. The study area is located in south-central Oregon, 26 mi north-northeast of Lakeview, OR. Federal and Lake County mining records indicate no mining claims, geothermal leases, or oil and gas leases within the study area as of January 1, 1987. No economic concentrations of minerals were found in the study area. The Wilderness Study Area is dominated by Abert Rim, a north-trending Basin and Range fault scarp that parallels the study area's western boundary. Exposed on the scarp is an approximately 2,000-ft-thick volcanic sequence consisting of Oligocene-Miocene basalts, tuffs, and tuffaceous sedimentary rocks.

Jan 1, 1987

By Constance F. Acton

Based on laboratory structure analyses, a pilot plant investigation was undertaken to evaluate a Michigan conglomerate native copper ore. Comminution or sized feed was accomplished using wet, closed circuit autogenous grinding with and without crushing of the recirculating load. Coarse metallics were concentrated in two stages of jigging with fine metallic copper being recovered in a three-stage xanthate flotation circuit. With a feed averaging 2.09 % Cu, copper recovery ranged from 86-93 % Cu with an average grade of 55.5 % Ca. An evaluation of the processing flowsheet is made in terms of pertinent independent, dependent, and external variables and design factors. Rate equations are developed to describe the grinding and flotation circuits separately as well as the entire circuit as a whole. Performance equations for the overall operation and for the unit operation of autogenous grinding alone are developed in terms of suitable capacity, efficiency and energy consumption terms. Thus, the effects of feed rate, recirculating load and flowsheet design can be rationally evaluated. Energy consumption for various conditions in the pilot plant is compared to the laboratory value. Additionally, size and scale up factors are discussed. Recommendations are made for further studies to be undertaken to further quantify the ore characteristics and the nature of the autogenous grinding operation. However, the feasibilty of beneficiation of this type of native copper ore by means of an autogenous grinding/jigging/flotation circuit is clearly established.

Jan 1, 1977

By J. Marts

Underground longwall coal mining sections are operated as sealed gobs if the coal is prone to spontaneous combustion. Sealing along the gate roads during longwall face retreat limits the flow of fresh air (oxygen) into the gob and thus deprives the spontaneous combustion reaction of oxygen. In a project sponsored by the National Institute for Occupational Safety and Health (NIOSH), researchers at the Colorado School of Mines have used computational fluid dynamics modeling to simulate the flow of gases in sealed longwall gobs. The models were validated using measurements and observations from the field and demonstrate that targeted injection of nitrogen along the gate roads inby the face can be used to control the size and location of explosive methane clouds within the go band to minimize or eliminate the explosion hazard resulting from the formation of flammable methane-air mixtures.

Feb 27, 2013

By I. Liebman

The Bureau of Mines conducted experiments on coal dust explosion suppression. The investigation took place on a beltway in the double-entry of the Bureau's Experimental Mine. Using conditions that simulate those in a working mine, the investigation showed that a coal dust explosion can be readily initiated in a conveyor belt entry. Also, the explosion can spread into adjacent entries through opened crosscuts (stopping destroyed by explosion) to propagate for long distances even though the adjacent entries are rock dusted in compliance with regulations. Passive water barriers (water-filled tubs) were found to be effective in suppressing explosions on a beltway; however, barrier efficiency was reduced by opened crosscuts. The study indicated that the beltway barrier should be the distributed type consisting of continuous rows of water-filled tubs covering long distances along the entry. A plan is outlined for the installation of a water barrier system in a working coal mine for the protection of a beltway.

Jan 1, 1981

By M. F. Dunn

The objective of this work was to define jet fan performance in d variety of large cross-section underground mine applications and to develop guidelines for thin performance in open airways, dead headings, and multiple face areas. Measurements include common ventilation instruments, continuous recording remote electronic anemometers to measure air velocity, and sulfur hexaflouride tracer gas with chromatograph analysis to determine dilution rates and air recirculation. For open airways the following were determined: Large jet fans are leas efficient in smaller airways, but quite effective in larger open airways for achieving both uniformity end greater air entrainment, when inclined about 10° or elevated. For dead headings the following were determined: The jet fan must be placed against the rib of the heeding closest to the incoming airstream from the crosscut or recirculation will increase. The fan should be placed at the pillar corner to increase airflow. As the fan is moved closer inby, recirculation increases. Larger fans promote recirculation. Inclining fans about 12° improves airflow in large headings. For face areas the following were found: For panels having uncontrolled airflow, the fan should be placed in the incoming airflow, about one pillar inby, and directed diagonally across the faces. For panels having narrower rooms and controlled airflow, the fan should be placed alongside the panel side in the first room so as to direct or intersect the incoming airflow at the next entry or crosscut.

Jan 1, 1983

By Julian Wills

The Candrill was developed with Soredem as a one-operator rockdrill for Canadian narrow vein mining. It provides the benefits of increased drilling rates, lower noise and vibration, mass reduction of 20% and system cost saving. The Candrill is to be commercialised at the end of 2001 together with a stoper drill through Parts Headquarters, Novatek's Canadian agent. The Candrill or pneumatic drills may be further exploited using a simple mechanised drilling system to further reduce operator labour, improve drilling speeds by up to 50% and to enhance drilling accuracy. Novatek's drilling system for simple mechanisation in gold and platinum mines is integrated with roof supports, can operate in stope widths as low as 800 mm and has resulted in labour savings of 50%, improved advances per blast of 20 to 50% and improved operator safety and ergonomics.

Oct 1, 2001

By W. Greuer

The objective of this paper is to demonstrate how site-specific slope stability analysis can be performed entirely from the desktop with satellite images, Geographic Information Systems (GIS), and slope stability software packages. This type of analysis would effectively eliminate or restrict the need for expensive field testing of geotechnical properties of a hillside, pit wall, berm, or embankment, and would be particularly useful for slope failure mitigation at remote or otherwise inaccessible locations.

Jul 17, 2000

By Narendra Gupta, Gaurav Srivastava, Abhinav Sharma

From the days when plain detonators and safety fuse were used for initiation of commercial explosives, the commercial blasting and mining industries have made rapid strides. With the advent of electronic detonators in the late ‘90s, the face of commercial blasting was changed forever. The Mining Industry in India initially took a while to embrace Electronic Blasting Systems (EBS), however, more recently the industry has taken to EBS in a big way.

Jan 1, 2015

By Jon K. Ahlness

The Bureau of Mines investigated technologies for testing the integrity of in situ leach mining wells, as required by environmental regulations. To test for leaks, inflatable packers were used to seal the well casing. Laboratory testing determined that the packers could contain a casing pressure up to 50 to 60 psi (345 to 414 kPa) less than the packer inflation pressure. Single-and double-packer configurations were successfully field-tested in 32 wells ranging from 500 to 530 ft (153 to 162 m) in depth. A rigid pipeline and a hoist truck were used to run the packers in and out of the wells for the double-packer tests, which averaged 2-1/4 h each. In an effort to decrease the time of the rigid-pipe double-packer test. a self-contained trailer-mounted test system was designed and built. It utilizes a winch and steel cable to run the packers in and out of the well and high-pressure nylon tubing for packer inflation. This system was successfully field-tested in eight wells averaging 650 ft (198 m) in depth and resulted in a time savings of 13 pct and an operator-hour reduction of 42 pct.

Jan 1, 1985

Effective gas management in coal mines, as well as proper ventilation design, is very important for maintaining the safety of underground coal miners. Advances in numerical modeling techniques have enabled evaluations of the coal mining environment using advanced grid designs and computed gas distributions through detailed mathematical models. These models help engineers to see the unseen areas of the mine through visualization of the data and ultimately help improve worker safety. This paper summarizes the modeling efforts conducted by NIOSH in the U.S. and CSIRO in Australia to address various gas management issues encountered in longwall mines. The modeling studies involved two of the most widely used grid-based techniques, namely computational fluid dynamics (CFD) and numerical reservoir modeling. This paper discusses the application of these techniques for gob inertization and gas control for spontaneous combustion, pre-mining degasification of coalbeds, gob gas venthole design and performance evaluation in longwalls, and gas management during development mining.

Jan 1, 2009

By D. J. Dodds, W. L. Schroeder

INTRODUCTION The plate loading test is a simple, useful tool in rock mechanics. The test consists of applying load to a rock surface and noting the resulting deflections. Plate loading tests are typically used to obtain modulus of deformation and related material properties, but can also provide information on blast damage and in situ stresses (1). Properties obtained are of course dependent on test procedure and test environment . In order to eliminate extraneous results it is essential that the interrelationship between the physical test environment and various rock properties obtained be thoroughly understood. Test interpretation is based upon elasticity methods, and the general assumptions made during analysis which include the following: 1. The rock is homogeneous, isotropic, elastic and continuous. 2. The stress is induced in a semi-infinite solid. 3. The plate is perfectly rigid or completely flexible. 4. Rock properties are independent of in situ stresses. 5. The plate and rock surface are smooth and parallel.

Jan 1, 1974

By Lisa Morrison

The 11th Annual Mineral Economics and Management Society (MEMS) conference was held April10-12, 2002, in Montreal, Quebec. It consisted of a series of technical sessions. Each paper addressed the economic issues that are related to the changes that many people believe are now required in the mining industry. Some of the papers were directed at how the mining industry will handle the changes that will be required in its philosophy and operations management. Of equal importance was whether the industry possesses the toolkit necessary to effect these changes and emerge stronger from its challenges.

Jan 1, 2002

By R. A. Lord, H. M. Prichard

Paper presented at Mineralisation in the Caledonides, the Mike Gallagher memorial meeting held in Edinburgh, 27-28 June 1996. The complex exemplifies a class of olivine-rich, platiniferous ophiolite complexes generated by unusually high degrees of hydrous melting above a subduction zone. Crystallisation of abundant olivine from unusually picritic magmas produced an exceptionally thick sequence of crustal dunite cumulates. Significant (1-4 ppm) concentrations of Pt+Pd occur where sulphide-bearing dunites are spatially associated with podiform chromite concentrations. In the area north of the Balta Sound, the chromitites appear to lie in distinct stratigraphic zones. A detailed programme of lithogeochemical and soil-rock interface geochemical exploration led to the intersection by diamond drilling of three stratiform horizons of sulphide-bearing dunites and associated precious-metal mineralisation. Patterns of cryptic geochemical layering, at scales from 200 m to less than 1 cm, suggests open-system fractionation

Jun 19, 1905

By Martin A. Elliott

Recommendations for safe practices in the operation of Diesel engines underground must take into consideration the hazards that might be created if the composition of the underground atmosphere differs from that of normal air. One aspect of this problem was discussed in the second report6/ of this series, which presented the results of tests in which a Diesel engine was operated with mixtures of normal air and exhaust gas supplied to the intake of the engine. Atmosphere .of this type were studied first because they will be present whenever the exhaust was is discharged into the atmosphere of underground workings in which an engine operates. Diesel engines in underground service may operate in another type of atmosphere, namely, one

Jan 1, 1941

By Martin A. Elliott

Recommendations for safe practices in the operation of Diesel engines underground must take into consideration the hazards that might be created if the composition of the underground atmosphere differs from that of normal air. One aspect of this problem was discussed in the second report6/ of this series, which presented the results of tests in which a Diesel engine was operated with mixtures of normal air and exhaust gas supplied to the intake of the engine. Atmospheres .of this type were studied first because they will be present whenever the exhaust was is discharged into the atmosphere of underground workings in which an engine operates. Diesel engines in underground service may operate in another type of atmosphere, namely, one

Jan 1, 1941

By H. C. van Zyl

Mine water in the Upper Olifants River Catchment in Mpumalanga(upstream of Loskop Dam) is at times discharged into local streams, resulting in local acidification and regional salination of surface water resources. Pollution of surface water can be prevented by collecting and treating mine water to a quality where it could be re-used without restriction (Cleanwater 2020 Initiative). Mine water in the Olifants River Catchment currently amounts to only 4,6% of the total water usage, but contributes 78,4% of the sulphate load. Limestone and lime treatment is the most cost-effective technology for neutralization and partial sulphate removal of acidic/sulphate-rich water to sulphate levels of less than 1500 mg/l due to precipitation of magnesium and removal of the associated sulphate fraction (through gypsum crystallization). Neutralized mine water of this quality may be suitable for irrigation. A number of alternative desalination treatment technologies were investigated (subsequent to gypsum crystallization pre-treatment) where treated mine water must meet more stringent quality requirements (e.g. less than 200 mg/lSO4). The capital cost of these processes varied between R4 million/(Ml/d) and R10million/(Ml/d) and the running cost between R2/m3and R5/m3. Water usage in the Upper Olifants River Catchment currently amounts to 947 Ml/d (including the power stations), and will increase to an estimated 1385 Ml/d by 2020. The additional water demand by2020 (438 Ml/d) will have to be supplied by importation from neighbouring catchments, and more efficient utilization of the local water resources, including excess mine water. Various levels of treatment are required to make mine water suitable for the following potential applications (acceptable treated water sulphate concentration shown in brackets): irrigation (2000 mg/l), coal processing plant (1000 mg/l), general industrial use (500 mg/l), discharge to public streams (500 mg/l), potable use (200 mg/l) and cooling water in power stations (20 to 40 mg/l). The following two options, or a combination thereof, can be considered for management of excess mine water in the Upper Olifants River Catchment: ?Collection and treatment of excess mine water to a quality suitable for selected urban and industrial applications (Option A) ?Collection and treatment of mine water to a quality suitable for irrigation (Option B). The estimated capital and running cost for Option A amounts to R528.5 million and R55.7 million/year, respectively, compared with R68,2 million and R11,9 million/year for Option B. It is recommended that Option B be investigated for implementation in the short to medium-term. Option B was selected due to cost benefits and the initial favourable results obtained by a joint Water Research Commission and Coal Industry initiative where mine water is used for irrigation. Option A may become feasible in the long-term to ensure maximum environ-mental protection and reduced treatment cost as a result of anticipated technological improvements over the next 5 to 10 years.

Jan 1, 2001

By Travis Q. Lyday

Mineral production in Fiji, a group of 322 volcanic islands and atolls of Melanesia in the southern Pacific Ocean, continued to be dominated by gold. However, the Fijian mineral sector remained a minor factor as a source of export earnings, Government revenues, and employment, generating only 1% of the gross domestic product (GDP), estimated as $1.2 billion.2 The largest and most important mining operation was the Vatukoula gold mine on the north side of Viti Levu, the main island. The Vatukoula Mine has been in prduction since 1932, producing about 3.8 million troy ounces of gold and 1.3 million troy ounces of silver to date. In April 1983, the large Australian mining firm, Western Mining Corp. (WMC), assumed operation of the mine in a joint venture with Emperor Gold Mining Co. Ltd., which operated the mine previously. The WMC takeover of the mine management was expected to bring in additional capital and technological expertise in order to modernize operations, increasing both efficiency and output. During the year, rate of recovery was only about 75% of the gold contained in the ore and only 40% of the contained silver. Mining at the Vatukoula Mine was done using bath opencut and underground methods, with about 60% of the ore mined attributed to the underground operations.

Jan 1, 1985