Search Documents

By Han-Tao Hu

Keywords: RH refining process, flow of molten steel, two-phase flow, gas holdup, circulation rate, mathematical modeling A three-dimensional mathematical model for the flow of the molten steel in the whole degasser during the RH refining process has been proposed and developed with considering the physical characteristics of the process, particularly the behaviors of gas-liquid two-phase flow in the up-snorkel and the momentum exchange between the two phases. The fluid flow fields and the gas holdups of liquid phases and others respectively in a 90 t RH degasser and its water model unit with a 1/5 linear scale have been computed using this model. The results showed that the flow pattern of molten steel in the whole RH degasser could be well modeled by the model. The liquid can be fully mixed during the refining process except the area close to the free surface of liquid and zone between the two snorkels in the ladle, but there is a boundary layer between the descending liquid stream from the down-snorkel and its surrounding liquid, which is a typical liquid-liquid two phase flow, and the molten steel in the ladle is not in a perfect mixing state. The lifting gas blown is rising mostly near the up-snorkel wall, which is more obvious under the conditions of a practical RH degasser, and the flow pattern of the bubbles and liquid in the up-snorkel is closer to an annular flow. The calculated circulation rates for the model unit at different lifting gas rates are in good agreement with the determined values.

Jan 1, 2005

By Piyush K. Dutta

This report describes the design, development and manufacture of a prototype quiet hard rock stoper drill and results of its field tests. It is shown that the stoper drill noise level can be reduced from 118 dBA to below 100 dBA by using this design. The design concept of this drill is based on a valveless independent rotation system, use of an integral muffler and pivot mount. The drill was manufactured in a standard commercial drill manufacturing setup and organization. The design and production technology proved that commercially viable quiet drills can be made available for mine use.

Jan 1, 1985

By Heloíza Döering Gasparin

Os efeitos de elevadas temperaturas e do tempo de exposição sobre as propriedades mecânicas de um ferro fundido cinzento hipoeutético foram avaliados em amostras de dois ferros fundidos da classe FC300, de mesma base, com diferentes percentuais de molibdênio. Ensaios de tração até ruptura a quente foram realizados em corpos de prova com diâmetro de 10 mm, usinados de um pino bruto de 30 mm de diâmetro. Os ensaios foram realizados a frio (temperatura ambiente) e a quente (200°C, 300°C, 350°C, 400°C, 450°C, 500°C e 550°C). Os tempos de exposição a elevadas temperaturas, após homogeneização térmica do material, foram de 0, 60, 90 e 120 minutos. As amostras com maior percentual de molibdênio (0,27% em peso) apresentaram melhores propriedades mecânicas para todas as condições ensaiadas. De acordo com a literatura a redução na resistência mecânica com a elevação da temperatura é atribuída à ocorrência de decomposição da perlita, como resultado da difusão do carbono vindo da cementita às lamelas de grafita, que é o responsável pelo aumento da quantidade de grafita no material. As análises metalográficas evidenciam a ocorrência deste fenômeno. Aumentos no tempo de exposição a temperaturas elevadas também contribuíram para a degeneração da perlita.

Aug 7, 2018

By Elbridge W. Gresseth

Rock deformational structures in a deep mine were analyzed by petrofabric techniques to learn (1) the relative magnitude and direction of the principal stresses involved in tectonic deformations prior to mining, (2) the preferred orientation of rock planar discontinuities which define rock anistropy prior to mining, and (3) the relationship of mining-induced rock failure to inherent rock stresses and inherent rock anisotropy. Rock fabric elements used for petrofabric analysis consisted of bedding planes, faults, joints, fractures, foliation, sericite plane (001), quartz axis [0001], quartz deformation lamellae, and microfractures. Structures and structural symmetries from different areas within the mine and from different scales of observation were compared to learn the nature of rock anisotropy and the orientation of the principal stresses defined by rock deformations. Analysis of such fabric as regional and macroscopic faults, b-c joints, quartz [0001], sericite (001), and microfractures, indicate that during the epochs of tectonic deformation, the maximum and minimum principal stresses were horizontally oriented and acted along northwest and northeast axes, respectively. This condition of regional stress appears to have continued during folding and the associated period of faulting. The most recent tectonic deformation represents a rotation of the minimum principal stresses into a vertical position, as shown by the development of a tensile joint system, quartz deformation lamellae, and microfractures. Good interscale correlation and statistical homogeneity of tectonic fabric indicate a stress field homogeneity in this area during tectonic deformation. Rock physical anisotropy is genetically associated with tectonic fabric and consists of preferentially oriented planar discontinuities intersecting along a nearly vertical axis. The mining-induced deformations were correlated with the inherent rock anisotropy which either directly controls or greatly affects their development. This phase of rock deformation shows a greater degree of stress field heterogeneity than was the case with tectonic deformations This is explained as a result of nonconfinement afforded by underground openings and the increase in ground stresses due to mining activity"

Jan 1, 1968

By Padmavathi V. Sagi

In this paper, effect of cyclic loading on the behavior of a long, flexible, unrestrained vertical pile loaded laterally in soft clay is examined. For cyclic loading, the analysis is carried out using a new method for the construction of p-y curves and for static loading conditions, p-y curves proposed by Dewaikar and Poonam (2005) are used. An iterative analysis is employed with secant modulus approach using a matrix method known as moment area method developed by Sawant et al. (1994). For pile top deflection of 20% of pile diameter, the load values are computed for both static and cyclic conditions. The comparison of results with the field test results reported by Matlock (1970) shows a good agreement. A parametric study is further carried out to examine the effect of load eccentricity, pile embedment length, diameter and the number of cycles on the pile response. The results of this study are discussed in the paper.

Jan 1, 2006

By James J. Anderson

In this talk I will report on an effort to reassess the risk of pile driving to juvenile salmonids migrating through Puget Sound. The study was motivated by the concern of the construction industry that provisions restricting pile driving during the spring migration is resulting in an unbalanced burden to the industry. In simple terms the industry wants to know if some construction can be conducted in the spring without harming the juvenile fish. Fisheries agencies have agreed to reconsider their regulations in the context of additional studies. So, in this talk I will present some thoughts on risk assessment in general and the results of our study to assess the impact of pile driving on Snohomish River juvenile pink and chum salmon that migrate through the Navy Homeport construction site at Everett. The research, which is being carried out by the Fisheries Research Institute at the University of Washington, was planned and is supported in a joint effort including: the Washington Department Fisheries, National Marine Fisheries Services, U.S. Fish and Wildlife Service; General, Manson, and Hurlen construction companies, the Department of Transportation and a number of Puget Sound ports authorities. I will first briefly discuss the early life history of the juvenile salmon the regulations are designed to protect Second, I will outline the legal criteria required for risk regulation and some specific thoughts on how a reassessment of pile driving risk might be approached. With this basis I will report on our research and how it can be applied to a new risk assessment.

Jan 1, 1990

By T. M. Barczak

A primary objective of the Bureau of Mines geomechanics research program is to develop a better understanding of support behavior and interaction of supports with the strata so that supports can be more closely engineered to the geological conditions in which they are employed. Four longwall shield supports were instrumented with an eight-transducer instrumentation array to measure leg, canopy capsule, and compression lemniscate link forces from which resultant shield loading was determined. The instrumented supports were monitored over a 4-month period, producing over 75 shield cycles of resultant shield loading. Resultant loading is the true measure of support resistance, providing both roof-to-floor and face-to-waste support reactions as well as the location of the reaction on the shield canopy. Observed roof support reactions were analyzed, with particular emphasis on horizontal shield loading, since it is the least understood design parameter. Average, peak, and change in shield loading during the mining cycle are discussed. Correlations among data parameters are examined, as is the distribution of support loading at the headgate and midface. Conclusions are drawn as to the effectiveness of the shield support at this installation. Recommendations are made for further research needs.

Jan 1, 1987

By J Cornejo, A Pinochet, C Caviedes

The ore extraction rate and the incorporation of new areas are key operational parameters. In massive deposits mined by caving techniques they both control the cave back geometry, which is mostly responsible for the induced stress state around productive levels. Early detection of deviations from admissible geometries will prevent stability problems related to geomechanical hazards, helping to improve safety and working conditions and reduce the potential for lost reserves.This paper describes a mine planning tool currently in use at the El Teniente mine. This tool involves the control of the cave geometry based on rules that have been defined as a result of different studies and experience collected during the operational history of the mine.This mine planning strategy achieves an extractive mining process with lower risk than conventional planning methods, ensuring ore reserves extraction if followed as planned while reducing unexpected changes in mining sequences.CITATION:Cornejo, J, Pinochet, A and Caviedes, C, 2016. Geometric control for strategic mine planning at El Teniente Mine, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 191–196 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By Taylor R. G

This paper reports a biogeochemical study of the Siberia lode of the Herberton tin field. Soil near the orebody contained high levels of Fe, Cu, Pb, Sn, As, Mld Mn. Polycarpaea spirostylis and Indigofera dominii were associated with these high levels but several other species apparently could not tolerate them. The potential of these species as indicator plants is discussed.

Jan 1, 1975

By Sam S. Taylor

Subsurface disposal of oil-field brines was practiced in Oklahoma on a limited scale as early as 1925. The technique of subsurface injection has been improved immensely and has been applied with varying success in many oil-producing areas in Oklahoma, and elsewhere. This method of disposal, however, is only one of several methods available to operators of oil-producing properties, but, in contrast with usual methods of handling brines on the surface it eliminates the damaging effect of mineralized water on fresh-water supplies, vegetation, and aquatic and other animal life. Other methods of brine disposal approved by regulatory agencies in some States include (1) impounding in impervious ponds and solar evaporation, (2) controlled diversion into surface waters, and (3) recovery of the mineral salts of the brine. In most States where oil is produced regulatory bodies authorize the use of one or more of these methods of brine disposal. In Oklahoma, for example, the .Oklahoma Planning and Resources Board of the Conservation Commission has been authorized4/ to adopt whatever methods or means may be necessary to prevent contamination by mineralization of all potable waters within the State.

Jan 1, 1942

Underground Mine Drainage may be conveniently divided into two operations:(a) Collecting and transporting drainage water to the pump eastern.(b) Elevating water to the surfacc by pumping.This short paper describes a system which automatically performs operation "a" and which has been developed on the South mine at Broken Hill, under the supervision of the mine foreman, Mr. F. McDonell. Operation "a" does not come under the heading of "subsidiary mine" drainage.SUMMARY(1) All drainage waters are collected by gravity flow into sumps.(2) Automatic control boxes operate syphons which transfer water from level to level to pump cisterns or to feed water service.EQUIPMENTSyphon Control Boar - Constructed of 10 ft. x 2 ft. oregon timber, suitably bolted together and equipped with a Bailey's cistern valve, with copper ball float control, and 12 in. pipcs and fittings forming a syphon (Fig. 1). One of these boxes is placed on each level at the shaft.The valve and float are so arranged that when the float is up (ie, box full) the valve will be fully open, and when the float is down (ie, box empty) the valve is closed. The vertical range between the cxtreme positions can be altercd by lengthening orshortening the adjustable arm of the float. The ideal valve is one...

Jan 1, 1927

By Max W. Ball

THE world's largest known oil deposit lies in northern Alberta. In fact, according to government estimates, the famous so-called 'tar sands' of the Athabaska region contain several times as much oil as all the other proved reserves of the world. S. C. Ells, of the Department of Mines and Resources, who has been the Dominion Government's authority on the oil sands since 1913, has estimated the minimum content of the deposits at 100 billion barrels(!). C. P. Bowie, of the U.S. Bureau of Mines, has published an estimate of 250 billion barrels(2). ?In comparison, the latest authoritative estimate of the proved oil-field reserves of the world is less than 35 billion barrels(3). Out of this tremendous total, perhaps 500 million barrels are commercially available at present-day costs and prices; the remainder must be considered a latent reserve to be used when development costs are materially lower and petroleum prices materially higher than they now are. Mean-while, the 500-million-barrel portion presently available contains more oil than has been found in all the rest of Canada, and constitutes one of Canada's great mineral resources. Although these deposits have been known to white men since 1788, when Peter Pond, the explorer, found the Indians stewing the oil out of the sand and mixing it with spruce pitch to caulk their canoes, they are only now coming into commercial production. The purpose of the present paper is to describe the deposits, their oil content, their present development, and the possibilities that seem to lie immediately ahead. For the sake of completeness and clarity, the writer has not hesitated to use or to paraphrase material that he has previously published elsewhere in discussing various aspects of the oil sands.

Jan 1, 1941

The extraction of minerals and coal at greater depth, employing higher-powered machinery to improve production levels, imposes an increased burden on the ability of a ventilation system to maintain an acceptable mine climate. Hence, mechanical mine cooling systems are often adopted, which can be expensive in terms of both their associated capital and operating costs. Consequently, in order to optimize the total mining costs, it is essential to provide the mine operator with a method with which to determine the most cost effective and efficient mine cooling system. In a previous paper1a novel energy analysis employing the concept of exergy was proposed and applied to cooling systems applied to two conceptual model mines, representative of UK deep coal operations, and their resultant subsurface thermal environ-mental conditions predicted. This paper presents an analysis of the results obtained from the application of this novel technique to assess the performance of various cooling systems applied to a current UK colliery that is experiencing climatic problems due to its depth and highly mechanized production and development workings. To perform this analysis, ventilation and climatic data collected at the case study mine were used to construct balanced mine ventilation and climatic network models to replicate the subsurface environment. Where air conditions exceeded specified climatic limits within identified climatically control zones, mechanical mine cooling systems were employed. A number of cooling system configurations were applied to these model to investigate the potential to satisfactorily regulate the thermal environment. The heat energy transferred out of the air stream by the various cooling methods was absorbed using a variety of chilled water systems, which were designed to operate at various water flow rates and temperatures. Models of various cooling system were developed and applied to control the underground climate within this mine network to within pre-set climatic limits. The results of a comparative analysis of the energy transfers that were produced by the application of the different cooling systems are presented in the form of exergy performance indices. The results produced by simulation models constructed to represent chilled water distribution networks to supply the various air coolers, are designed and balanced. The results of the exergy analyses applied to the operation of the various chilled water pipe networks are discussed and used to assess the exergetic performance of the application of each proposed cooling system to the mine ventilation network.

Jan 1, 2004

By Dan A. Brown

This paper describes a method of conducting rapid lateral loading tests of deep foundations in which the load is applied to the foundation with a time duration of less than one second. For purposes of this paper the loading is applied using a pyrotechnic loading system commonly referred to as Statnamic. However, the method should apply to any lateral loading system which produces a force time history with a loading duration of 20 msec to 1 second. The test provides a measure of the dynamic and static response of the soil/foundation system and must be evaluated as a dynamic loading. Interpretation of the test includes a simple single degree of freedom (SDOF) model which can account for the inertial effects of foundation mass, system damping, and static foundation stiffness. The results of the test measurements are compared with four case histories in which comparative static load test data are available, including pile group foundations and large diameter drilled shaft foundations.

Jan 1, 2007

By H. Lyn Bourne

This is the ninth annual tabulation of royalty information. Again this year, some of the older information has been deleted to make room for more than 30 new entries. Several articles and publications crossed the author's desk this past year that relate to mineral valuation and mineral royalty. Tom Loucks presented a paper, "The Valuation of Hard Rock Mineral Property," at the Rocky Mountain Mineral Law Foundation in Santa Fe, NM in July, 1990. His paper gives an indepth explanation of the definitions and concepts related to mineral valuation. It includes descriptions of numerous legal cases that have dealt with mineral valuation and proper reference is given for each case. Loucks works for the Denver Mining Finance Co. Gold royalties generally range from 5% to 7%, net smelter return. However, Severn Brown sent information that shows a much wider variation. Echo Bay Mines reported in its 1989 annual report royalties that range from 1.5 % to 30% for gold from various gold properties. Brown also sent a copy of an article that appeared in the Dec. 27, 1982, issue of Fortune magazine. This issue carried an article by Walter Guzzardi, Jr. "The Huge Find in Roy Ash's Backyard." The article gives the history of Newmont's leasing in Nevada on property that became the Carlin, Bootstrap and Blue Star Mines. The article states that the initial royalty was 10% that escalated to more than 16%. Another property, the site of Gold Quarry, provides an 18% royalty to the same own¬ers. The article makes interesting reading for those interested in mining history.

Jan 1, 1991

By R B. Stewart

Where pasture production is the intended land use of the areas to be reclaimed, the creation of a suitable growing +medium is a major objective. To achieve this land reclaimers require a sound understanding of the proposed mining plan and a knowledge of the physical, biological and chemical properties of materials intended for resurfacing disturbed areas. Where the original soil is not being replaced in its natural state, research is usually required to determine an alternative growing medium. Results from field research conducted on waste material from the Waihi Gold mine are reported with emphasis on the significance of soil depth in relation to pasture production in this environment.  Problems in extrapolating field research to large scale operations are also considered.   Essentially the requirements for successful pasture production, on surrogate growing medium, are akin to conventional approaches used in New Zealand in the development of unimproved agricultural land. High inputs of fertiliser are initially needed, especially where volcanic soil is used, and careful management of pastures and soils is required to minimise soil erosion and create a sustainable system. In the first three to five years of pasture production, grazing use of the land requires to be dictated by pasture availability and soil conditions and not by animal feed requirements. The use of light stock (young dairy or sheep) is recommended.   Successful land restoration requires a team approach by a range of cooperative specialists including engineers, soil scientists, farm managers, agricultural contractors, landscape architects and environmental officers.

Jan 1, 1991

By Braja M. Das

Laboratory model test results for the ultimate uplift capacity of square and circular foundations in saturated clay (ø=0) have been presented. The results of the present model tests for square foundations have been compared with the previously published laboratory model tests results on circular foundations. Based on the comparison, it appears that the critical embedment ratio of square and circular foundations increases from about 3 for soft clays to about 7 for medium to stiff clays. By using the experimental results, an empirical procedure has been suggested for determination of the ultimate uplift capacity of belled pier foundations in saturated clay.

Jan 1, 1987

By F. F. Skiba, P. J. Root

A mathematical model has been used to investigate crossflow effects in a stratified reservoir during an idealized displacement process. A process in which one incompressible fluid displaces completely another incompressible fluid of the same density and viscosity was considered. The reservoir was assumed to be composed of homogeneous layers which are discrete but interconnected. Approximate five-spot flow geometry was simulated by arranging two pie-shaped cylindrical (two-dimensional) wedges in series. Some of the common production methods rely, for their effectiveness, on the fact that the formation consists of isolated strata. This is particularly true of selective plugging and single-zone production-injection methods. The effectiveness of these techniques for several cases in which adjacent strata are in communication has been evaluated. The usual production-injection schemes for fluid injection processes involve using the same completion interval in both the production and the injection wells. The efficiency of this, as well as alternative productioz-injection procedures has been examined for some cases involving communicating strata. INTRODUCTION The performance of many fluid injection projects is marred by early breakthrough and by production of a high percentage of the displacing phase after breakthrough. This channeling effect, if it occurs in reservoirs which have large permeability variations, is often explained on the basis of a model composed of discrete, isolated strata. Corrective or preventive measures based on this same model are also common. The behavior of stratified models has been the subject of considerable study. An excellent review of the early literature was given by Seba.1 Studies of the depletion performance have since been made for continuous, unrestricted communication between strata2-4 and for production from one permeable bed in continuous but restricted communication with an adjacent permeable bed.5,6 Model studies of displacement processes in stratified systems with crossflow also have been reprted.7-12 Finally, methods which account for crossflow have been developed for computing displacement behavior in stratified systems.13,14 Most methods for controlling or preventing channeling involve some change in the interval open to production and/or injection. Although many variations of the selective completion problem have been studied in regard to the depletion of a reservoir, little attention has been given to the behavior of a displacement process under similar conditions. Sebal used a resistance network model to study the performance of a process in which one incompressible fluid displaces an identical fluid from a linear, stratified reservoir. He investigated the possibility of improving the vertical coverage by limiting the completion interval of the production well. This investigation deals with techniques in which selective completion of the production and/or the injection wells is used in an attempt to control channeling. At one extreme, selective plugging and single-zone isolation (assuming perfect execution) should be successful if the reservoir is actually made up of independent strata. At the other extreme, they can hardly be expected to be successful if the channeling is caused by a mechanism in which stratification effects are negligible even though there are extreme variations in the formation permeability and/or the injectivity profile of the wells is not uniform. By contrast, it is difficult to anticipate the effect that the amount of communication between the beds of a stratified system will have on the efficiency of selective completion techniques. The objective of this study is the quantitative determination of the effect of communication on the behavior of some particular stratified systems which will at least lead to qualitative conclusions.

Jan 1, 1966

By Chris G. Leach

"Abstract A seven storey Northbridge area of Perth, Western Australia presented residential apartment complex located in the an opportunity for a novel application of Cutter Soil Mix technology (CSM). The development included a two-level basement for car parking which covered the full site area. However, the basement was also required to extend under an existing single story heritage building. Soil conditions comprised 2m of fill overlying medium dense to dense sands that in turn were overlying a very stiff clay stratum at approximately 14-16m depth. The ground water table was located at a depth of approximately 1m below the natural surface level.A site boundary consisting of a reinforced CSM retention system and was designed and installed to allow the excavation to proceed to basement level. Two rows of temporary soils anchors or inclined struts were required to achieve this. A CSM support system for the heritage building was also designed and constructed to provide temporary support during excavation and permanent construction works. The brief for the contract works emphasised that it was vital that settlements of the heritage building be kept within strict limits.CSM is a relatively new introduction to the Australian construction market, using a modified trench cutter to mix a binder slurry with in situ soils, generally to form cut-off walls, retaining walls and soil improvement works. This project is understood to be first application of the CSM for underpinning work in Australia.This paper discusses the site background details leading to the decision by the client to adopt CSM technology, and the design and construction aspects to meet the challenges offered by this project.Introduction190 Newcastle St is a 7-level residential apartment complex located in the Northbridge area of Perth, Western Australia. The development includes a 2 level basement for car parking, which covers the full site area. The basement also extends under a single story heritage building, which remained in-situ throughout the building works.A site boundary retention system was required to allow the excavation to basement level to proceed. In addition, a support system for the heritage building was required to provide temporary support during excavation and permanent construction works."

Jan 1, 2014

By J. H. Zietsman, M. W. Erwee, P. J. A. Bezuidenhout, Q. G. Reynolds

"Pyrometallurgical furnaces are tapped through tap-holes that are opened with drills and oxygen lances. The lance is often used on its own or as the last step of opening the tap-hole. Interaction of oxygen with molten material inside the tap-hole can occur, and is a phenomenon that is not well understood. As part of a study that focuses on the effect of lancing on flow inside and around the furnace tap-hole, a cold-model validation was done. The validation study focuses on validating the MULTIPHASEINTERFOAM multiphase flow solver in OpenFOAM® for the problem involved. The sensitivity of the model to different materials properties (viscosity and density in particular) is presented with both cold models and the results from flow simulations in OpenFOAM®. IntroductionMany pyrometallurgical operations are carried out in furnaces where molten material accumulates continuously. Once enough material has accumulated and is ready to be removed from the furnace, material is tapped through one or more tap-holes in the furnace. Tap-holes differ significantly in both geometry and materials of construction, depending on the process involved – examples of different types of tap-hole configurations can be found in, for example, Nelson and Hundermark (2014). Tapholes all share one common feature: they are high, wear areas of the furnace. Molten material at high temperature flows through these areas, after which the tap-hole is sealed, usually using tap-hole clay. The purpose of the tap-hole clay is to harden inside the tap-hole and seal it until the next tap.Once ready to tap, a pneumatic drill and/or oxygen lance is used to open the tap-hole. The extent of lancing a furnace tap-hole depends strongly on the type of furnace. In, for example, many blast furnace operations lancing is limited as much as possible, and done only if drilling was not effective. In other operations, such as on small-scale pilot furnaces with short tap-holes, only lancing is used to open the tap-hole."

Jun 1, 2019