Search Documents

By Karl R. Becker

A variety of commercial detonators (fuse type and electric instantaneous and delay types) were subjected to impact and thermal stimuli to determine initiation stimulus levels and the dominant parameters in resistance to initiation. In the impact trials the detonators were impacted along their length to find the most sensitive region; threshold initiation limits obtained for these regions ranged from 3.47 to 20.82 joules (2.6 to 15.4 ft-lb). The friction sensitivity of the explosive component was an important parameter in determining sensitivity; various construction features of nonexplosive components played a role as well. In the thermal sensitivity trials, the detonators were heated from ambient to 100° C at an average rate of about 1.0° C/min, and thereafter at 0.5° C/min until they exploded; the explosion temperatures observed ranged from 121° to 188° C. These temperatures correlated quite well with the reaction temperatures of certain characteristic explosive components used by different manufacturers. The data also indicated an effect of confinement on explosion temperatures of detonators.

Jan 1, 1975

A summary of a proposal to develop a 20 000 tpa underground gold operation in a Forest Park. The environmental constraints are severe and affected the mine development planning and choice of mining method. The mine will use trackless methods to access the narrow 1.5 m ore shoots, and to mine ore by cut and fill methods. The use of Microscoop and CT 1700 HE electric LHDs for mucking, together with special drilling attachments for drilling, is central to efficiency and small Kubota diesel haulers will be used for carrying ore to surface.

Jan 1, 1986

Ground conditions at the Kencana mine, Indonesia, are generally poor and an underhand cut and fill mining method is used for extraction. Due to these poor ground conditions, all vertical development has been conducted using blind, top-down, sink and line excavation methods. Due to time constraints, raiseboring was considered the only viable excavation method for the installation of a return ventilation system for the K2 (Kencana extension) project. In order to achieve successful raiseboring in the poor ground conditions a number of strategies were used including: a detailed geotechnical study for optimal position of the shaft/s, splitting shaft excavation vertically, raiseboring of multiple smaller diameter shafts, extensive pregrouting, installation of drainage holes, and rapid installation of support following excavation.

Nov 25, 2010

By C. A. Rowland Jr

"I. INTRODUCTIONFred C. Bond's ""Third Theory of Comminution"" (1) was published in 1952. The mathematical statement of the Third Theory is the well-known Bond Formula:where W - Kw H per short tonWl - Work IndexP - Product size in microns which 80% passesF .. Product size in microns which 80% passesWork Index, as defined by Fred Bond, "" ... is the comminution parameter which expresses the resistance of the material to crushing and grinding. Numerically, the Work Index is the KwHrs per short ton required to reduce the material from theoretically infinite feed size to 80% passing 100 microns."" (2)Work indices for grinding can be obtained tram Bond grindability tests and can be calculated from plant grinding mill operating data when power consumed per ton of ore ground, the feed size analysis and the product size analysis are known.Work indices obtained tram Bond grindability tests, having been obtained from standard and controlled laboratory procedures, are reproducible and for the sample tested are accurate. The degree of accuracy relative to plant mill operation depends upon how representative the sample is of the total mill feed.The results of the Bond closed circuit rod and ball mill grindability tests (3) are given in grams of product sized material produced per revolution of the test mill. In developing a method to evaluate plant operating data and results from his grindability test, Fred Bond developed the ""Third Theory of Comminution."" In the process formulae were developed for converting grams per revolutionobtained from grindability tests to work index.The standard feed sizes for the Bond grindability tests are:Rod Mill Test ore crushed to minus 1ll inchBall Mill Test ore crushed to minus 6 mesh (Tyler)The formulae for converting grams per revolution to work index incorporate the 80% passing sizes for the feed to and the product produced in the specific test. Therefore, accurate work indices can be obtained from Bond grindability tests when the feed size is finer than standard. To obtain accurate test results, the ratio of reduction should be greater than 6 to 1."

Jan 1, 1972

By I. Mihajlovic

This paper investigates a potential method for arsenic removal from copper concentrates using hypochlorite leaching. The problems concerning pyrometallurgical processing of copper concentrates with high arsenic contents are discussed. A possible solution to the problem by leaching of natural enargite crystals with sodium hypochlorite under alkaline oxidizing conditions, with enargite converted into crystalline CuO and the soluble arsenic forming AsO43-, was experimentally investigated and results are presented. Kinetic parameters were calculated for enargite leaching, using a model-free approach. Advanced isoconversional methods were used to investigate the dependence of activation energy (Ea) on reaction rate (a). Keywords Enargite, copper concentrate, isoconversional method, kinetics, activation energy.

Jan 1, 2011

By Mark Jolly

"Instead of using the traditional batch casting process, the CRIMSON [1] (Constrained Rapid Induction Melting Single Shot Up-Casting) method employs a high-powered furnace to melt just enough metal to fill a single mould in a closed crucible. The crucible is transferred to a station for computer-controlled counter gravity filling of the mould for optimum filling and solidification. The CRIMSON method therefore holds the liquid aluminium for a minimum of time drastically reducing the energy losses attributed to holding the metal at temperature. With the rapid melting times achieved, of the order of minutes, there isn’t a long time at temperature for hydrogen to be absorbed or for thick layers of oxide to form. The metal is never allowed to fall under gravity and therefore any oxide formed is not entrained within the liquid. Thus higher quality castings are produced leading to a reduction in scrap rate and reduced overall energy losses.IntroductionEngineers at the University of Birmingham, England, with local company, NTec, have invented a new casting process that will reduce the energy costs of light-metal foundries. The technology, entitled CRIMSON, means that foundries need only heat the quantity of metal required to fill a single mould rather than large batches that use unnecessary energy and create waste. The complete concept of CRIMSON requires a change of philosophy in the approach to casting and requires the user to think holistically in order to reap the full benefits from the process. This paper will discuss the various aspects of energy wastage within the foundry sector and discusses the processes whereby the energy can be reduced. Primarily the author focuses on the aluminium sector but CRIMSON can be applied to many of the non-ferrous “light” alloys. Ferrous materials and non-ferrous “heavy” alloys can also benefit from some of the ideas but not necessarily directly from the application of CRIMSON."

Jan 1, 2010

By Bill Elverman

Randy and Kenny Robison have visited every coal mine that would let them in the door, to survey the best mining practices. The brothers have spent nearly their entire lives working in coal operations. The Robison’s started out on lube and grease trucks and worked their way up to respected industry leaders in Alabama. The Robisons have owned MS&R since 1989. Since then, they have created a niche for themselves in providing coal for Alabama’s metallurgical coal market. A great deal of the knowledge the Robisons have amassed throughout the years has come from observing — taking note of what works and what does not. In early spring 2004, they commissioned a Komatsu America PC3000 Super Shovel. Outfitted with a backhoe attachment and a 16-m3 (21-cu yd) bucket, MS&R’s PC3000 is currently one of the largest mining excavators working in Alabama.

Jan 1, 2005

By Clay Haynes

In 2005, Black & Veatch Corporation began designing a raw water conveyance system for San Luis Obispo County from Lake Nacimiento to the city of San Luis Obispo. The first element of the water transfer system will be a raw water pump station and lake tap. The wet well of the pump station will consist of a concrete lined shaft approximately 180 feet deep constructed in the very incompetent sandstone of the Vacqueros Formation. The lake will be wet tapped at approximately 172 feet below grade using a slurry earth pressure balance tunnel boring machine. The 48 to 72-inch finished diameter microtunnel will be approximately 500 feet in length. Construction is scheduled to begin in the winter of 2007.

Jan 1, 2008

By Gao Dazhao

This paper presents some research results of pile foundation performance. Measurements on the bearing behaviour and driving effects of piles have been carried out during pile testing and pile driving. It has been found that the ratio of end resistance to the ultimate load depends on the pile length, and the ratio in general is less than 40% for single piles. However for pile group, the end resistance seems to be greater than skin friction. The characteristic curves of skin friction and end re­sistance appear as interaction between soils and pile. The contribution of skin friction to the pile bearing capacity not only depends on soil properties but also on the relative position of the soil layer. The pore pressure and the lateral pressure in ground have been observed during the stage of driving piles. Based on the available data, the radius of plastic region and the coefficient of pore pressure A can be found analytically. The pore pressure time process curves which may be used for practice have been predicted by means of numerical method.

Jan 1, 1991

By Alan B. Wagner

Data from seven instrumented pile load tests in Milwaukee, Wisconsin and two other instrumented load tests reported in the literature, one in Evanston, Illinois and one in Houston, Texas were reviewed. The data were for pipe piles having diameters from 9-5/8 inches to 18 inches, driven to depths between 36 and 96 feet. These data were used to develop a relationship between effective vertical stress and unit side friction and unit end bearing. These relationships were based on readily measured soil parameters, undrained shear strength, Cu, and Standard Penetration Test (SPT) values. This Beta (ß) and Nt approach and four other methods were then used to calculate the bearing capacity of the nine cases analyzed. The results from each of the methods are compared with the measured results.

Jan 1, 1991

By Sunil Koppalkar, Guillaume Noel, Ahmed Bouajila, Makni Sami, Claude Gagnon

"Gold gravity recovery circuits utilizing enhanced gravity separators have become an integral part of many of the modern gold processing plants. Thus, efforts to improve the operating efficiency have been a topic of interest for metallurgists for many years. As part of this endeavour, a methodology to estimate the portion of gold in the ore that could be recovered by gravity separation (gravity recoverable gold or GRG) was developed at McGill University. It has been reported in the literature that the gold content estimated with this methodology is the theoretical maximum that is available for gravity recovery that could only be approached but never achieved. A comparison of GRG recovery obtained in the laboratory with the actual recovery in the plant shows that plants recover between one-third to two-thirds of the value predicted by the laboratory test.Research conducted at COREM shows that particle shape transformation during grinding is a major cause of the discrepancy (even though the bleed percent processed, the quality of cyclone classification and the operating conditions of the gravity separator also contribute to the difference). To analyze the gold particle shapes and their deportment, samples were collected from different streams of a grinding-gravity circuit in a gold plant and compared to a concentrate sample from the standard GRG test. A particle characterization methodology based on gold morphology was developed. GRG mapping in a conventional grinding-gravity circuit and the transformation of GRG into non-GRG, as mainly explained by gold particle reshaping, will be discussed. The knowledge gained from the shape analysis will be used to develop shape distributions and partition curves for the classification of shapes.INTRODUCTIONGravity concentration using centrifugal concentrators has gained increasing popularity since the invention of the enhanced gravity concentrators in the nineteen eighties. Among these, the semicontinuous centrifugal gravity concentrators are most commonly used for recovering gold and platinum group minerals (PGM) from grinding circuit streams. The benefits of gold gravity recovery are now well understood and the acceptance by the mining industry is overwhelming. The occurrence of reasonable amounts of gravity recoverable gold (GRG) in an ore prompts gold mills to install gravity circuits. Thus, the increased use of gravity concentration has necessitated a better understanding of the behavior of gold in grinding circuits and of the factors affecting the performance of the gravity concentrator (Laplante et al., 1995). Due to its high density (19.3 g/cm3 when pure) and malleability properties, gold tends to accumulate in circulating streams making it attractive for gravity recovery. The gravity recovery units are typically installed on a bleed stream of the cyclone underflow, mill discharge or cyclone feed."

Jan 1, 2011

By W. L. Thayer, K. A. Jonasson, R. D. Coleman, J. D. Hazlett, C. E. Capes

"Loss of coal fines in reject slurries limits the yield of coal cleaning operations. Difficulties in handling fines also limit the extent of physical cleaning in treating coals with finely-disseminated impurities. Selective oil agglomeration allows even extreme fines to be processed and offers some novel approaches for coal cleaning and utilization.The oil agglomeration process for the recovery and beneficiation of fine and ultrafine coal has now been commercialized by the Chemical Engineering Section/Chemistry Division of the National Research Council (NRC). This paper describes these activities to apply oil agglomeration and related fine coal technologies on an industrial scale. Pilot plant and large scale results are described, as well as aspects of agglomerate utilization in both wet and dry form."

Jan 1, 1988

By J. G. Ross

IN the paper entitled Block Caving at the King Mine (1), which was presented at the Annual General Meeting held in April, 1934, at Quebec, it was pointed out that, owing to certain conditions and financial restrictions, it was advisable to provide a temporary shaft. This was raised from the )00-ft. level to the bottom of the pit, and a 45-degree incline track was constructed up the face of the pit to surface. The temporary shaft and incline were within the ore-body, but were to be used only until such time as the new shaft-the subject of this paper-could be sunk and made ready for operation. After a careful study had been made of all available information pertaining to the ore-body, including examination of diamond-drill core records and geological data, a shaft location was selected well outside the ore-body. Further, since the crusher and dryer buildings are located over part of the ore-body, it was necessary to plan the removal of these buildings and to construct a new crushing and drying plant. This, and the new shaft, must operate in conjunction with the present mill and rock storage bin, which would continue robe used as formerly. No part of this programme, with the exception of drifting toward the shaft site, was started prior to 1937. More than usual detail on technical features is given in this paper in the hope that some parts of it may be of assistance to other members of the Institute who have to undertake somewhat similar work. The engineering and operating staff designed and supervised the work, while at the same time carrying on regular production in four mines at the rate of 12,000 tons of rock mined per day, the output at the King mine being at the rate of 140 tons per hour. No additional engineers were required.

Jan 1, 1939

By Chas. F. Jackson

During the past year a special study was made of shrinkage stoping A large number of mines in the United States and Canada which employ this method were visited and their practices were discussed with the operating staffs. The operating data obtained are appended hereto. Data were also abstracted from the literature on other mines and are combined in tables with data personally secured by the author. References are made to these published articles, some of which have appeared as information circulars of the United States Bureau of Mines, in the Transactions of the American Institute of Mining and Metallurgical Engineers, and the Engineering and Mining Journal. Several of the mines referred to which have not been described in individual papers will be described in detail in information circulars to be issued by the bureau. Eventually it is planned to combine and condense the information in these circulars and present the data in bulletin form.

Jan 1, 1930

By Roberto Bria

El presente texto describe el módulo prefabricado para las salidas de emergencia. En este sentido, el sistema modular prefabricado busca facilitar y agilizar la instalación de salidas de emergencia desde el interior de mina hasta superficie mediante RB entubados con módulos armados fuera de la Unidad Minera, mejorando la seguridad mediante un sistema confiable de fácil colocación, reutilizable, y de gran robustez. De ese modo cumplir con el objetivo primordial de las salidas de emergencia de 200 m hasta la superficie, en terrenos de calidad de roca regular a mala.

Sep 21, 2013

A shortage of technical skills in all areas of the mining industry is being experienced worldwide. This has significant consequences for design, operations, productivity and safety and, therefore, needs to be seriously addressed, both in the short and longer term. It is therefore both a strategic and a tactical issue. Importantly, however, since mining is a long-term business, the shortage of skills must be dealt with from a strategic point of view to ensure the supply of the necessary skills for future mining. This paper will deal specifically with the provision of high level technical skills, that is, university graduates in mining engineering, and the outlook for the institutions that are currently producing such graduates.

Jan 1, 2008

By D. E. L. Zapata, O. J. R. Baena

"INTRODUCTION Mining is a fundamental part of the historical and economic development of a country. In Colombia, this is reflected from pre-Columbian jewelery, to being now one of the first exporters of coal worldwide, in 2017, the Colombian mining sector contributed approximately 6% of GDP (Ministerio de Minas y Energía, 2017). Coal, nickel, gold, platinum, emeralds, limestone, salt, phosphate rock, clays, siliceous sands and to a lesser extent copper, manganese, magnesite, barite, gypsum and various types of ornamental rocks, among others are produced (UPME, 2016). The contributions of mining activity in the economic dimension is more measurable, on the contrary in other dimensions, as the social and environmental, for this, every day there are new proposals and tools oriented to strengthen how to evaluate the contributions in terms of the sustainability and responsibility, with the aim of quantifying, concreting and non-utopian, to improve the life quality of a community and not only to comply with reporting and gaining prestige. Colombia has a generalized increase in the mining sector where the levels of informality and illegality are evident only 10% of mining activity is legal (UPME, 2014), also, the mining sector is accused of human rights violations, high levels of inequality, poverty and the affectation of ecosystems due to bad environmental management, among other situations (ACNUDH Colombia, 2015). This problem has generated rejection to the realization of the mining activity in many places of Colombia. At this point, it is important to clarify this problem is more complex, different actors are involved in this conflict, but it is an evidence that is needed a sustainability model for specific realities such as the Colombian mining. This situation in the current mining activity, is similar to the chemical industry situation three decades ago, because of an extensive problem in relation to repeated work accidents, natural disasters and indications as a highly polluting and unsustainable industry, with the aim of improving, not only this public perception, but also in the way of carrying out the business activity. Thus, in 1985, the Canadian Chemical Producers Association released the Responsible Care Program (RCP) (ICCA, 2015). Being aware that companies were responsible for the affected lives in some way by the operation and needed to improve workers safety, environmental protection and most importantly how legal persons should comply with the law, but go beyond this. RCP is most recognized sustainability initiative in the chemical sector, companies associated are recognized for having high quality standards, continuous improvement, visibility, corporate ethics, environmental and social management (ACC, 2015). In addition, to meeting the objectives is set out the creation of a model that increasing reputational sector levels. This initiative is considered to be a worldwide successful case of reporting corporate responsibility indicators and contributions to sustainability from the industry sector to local development (BASF Group, 2016)."

Jan 1, 2018

By Rogerio Castejón

The evolution on the computer in the last 10 years have caused a big change on the way the mining companies are doing exploration. The following factors have contributed to that change: the downgrade of computers and software cost associated with the “usability” (easy of use) of the present systems (remember the old DOS and UNIX systems). New systems are more focused on the users rather than on the experts in applications, meaning that the geologist must understand geology and not operational system, programming, etc. Market conditions requires exploration to be faster and more intelligent than in the “old” times, and companies are always demanding quicker answers from their geologist group as well as lower exploration budgets. Exploration teams must be more effective and efficient. In this sense, the only way to achieve those requirements is to use the proper techniques, methods and tools on the diverse stages of exploration. Its necessary to consider that the costs of data acquisition increase, almost exponentially, through the stages of exploration, from grass roots to advanced stage.

Aug 25, 2002

By D. K. Crampton

The object of this work was to obtain and correlate information on effect of internal stress in variously drawn tubes on several properties. Also, a simple approximate method of comparing types of stress distribution in such variously drawn tubes was sought. There is also included some work on comparison of single and polycrystalline materials and effect of different types of operation and preferred orientation. Preparation of Material A series of tubes was drawn to study the effect of the type and degree of final reduction on various physical properties and the approximate distribution of stress intensity across the tube wall. The material used all came from a single heat of 70-30 brass melted in a regular production Ajax-Wyatt induction furnace. The analysis of the metal as cast was: copper, 70.36 per cent; lead, 0.04; iron, 0.02; zinc, balance. The material was cast in "shells" with 4 in. outside diameter and in. wall thickness. It was drawn part way down according to the usual standard mill schedule and then by suitable individual schedules to finish by a variety of types and degrees of drawing to the same final cases in every instance; namely, 0.750 in. outside diameter by 0.080 in. wall thickness. The exact final draws, together with the percentage area reductions, diameter reductions and gage reductions are given in Table 1. In fabricating these tubes, rather unusual precautions were observed to insure the elimination of ail variables not under immediate study. All intermediate anneals were carried out at about 1200" F. down to the so-called "cut-in size"; namely, 17/16 by 3/16 in. From this point on, all anneals were made at from 1050' to 1100" F. The greatest care was used all through to have the tubes as free from minor surface defects as possible. When such defects were visible on intermediate sizes they were carefully filed out. On the final draw to 3/4-in diameter the die was aligned with the greatest possible precision in order to insure as straight a tube as possible

Jan 1, 1933

By Anne Kvithyld

Silicon solar cells, that convert the energy of sunlight into electric energy, are attractive sources of energy. In the production line wafers of solar cells are sliced from a multicrystaline ingot solidified unidirectionally. Recycling scrap from top and sides of such ingots is addressed. SiC and Si3N4 inclusions are a major problem. Scrap from Scan Wafer ASA is melted in a high vacuum furnace at around 1500ºC. The filters, from commercial producers, are C and SiC with 10, 20 and 30 ppi. Characterisation of inclusions before and after filtration, and in the filter itself, is performed by microscopy. Dissolution of silicon in acid and counting of the un-dissolved inclusions is also carried out. In the filter Si3N4 needles and SiC inclusions were identified. The amount of these inclusions in the filtered silicon is much less than in the input. In conclusion, filtration using SiC and C filters in vacuum system in argon atmosphere removes SiC and Si3N4 inclusions from solar cell scrap. Flow of metal through the filters is not a problem. These results are promising with scale-up to industrial application in mind.

Jan 1, 2006