Search Documents

By John D. Bardill

Data from extensive tests was obtained on friction-head losses of various sand slurries, composed of materials of different specific gravities and under varying transport conditions, to provide useful information for designing hydraulic transport systems. The tests were run in a pilot plant through 2-, 3-, and 4-inch lines with slurries composed of relatively pure barite and limestone solids. Available grinding and classification equipment did not permit attaining a comparable size distribution in the two materials tested, thus preventing direct correlation of friction-head loss values to physical properties or mineral composition. A total of 495 measurements were made of limestone slurries in the 2-, 3-, and 4-inch pipe test sections at flow velocities from 6 to 14 feet per second and pulp densities from 40 to 70 percent solids. A total of 640 measurements of barite slurries were made in the 3-and 4-inch pipe test sections at flow velocities between 7 and 14 f.p.s. and pulp densities ranging from 40 to 80 percent solids.

Jan 1, 1962

When the Organic Act of 1910 established the Bureau of Mines within the Department of the Interior, the Bureau's programs involved only health and safety research and, education, and fuels testing. As the Federal Government's primary agency for research in minerals, the Bureau has expanded its scientific and technological investigations to mining, processing mineral substances, eliminating occupational health and safety hazards in the mineral industries, economic development, and resource conservation. Today, Bureau activities cover a broad spectrum of programs for meeting the diverse (and sometimes conflicting) needs of mineral industries, government, and the public. In the 1960's, the Bureau initiated programs to resolve environmental problems associated with past mining and mineral processing. In the 1970's, the energy crisis raised the national consciousness concerning our limited supplies of domestic mineral and fuel resources. Dependence on foreign sources of raw materials critical to our national economy and competition from other countries for these world supplies stimulated the need to conserve and use with intelligence the Nation's minerals, metals, and fuels.1

Jan 1, 1977

By T. P. R. de Jong, H. Harbeck

"This contribution reports recent mineral sorting experience and lists the opportunities of the newest generation of automatic sorters with a special focus on electromagnetic detection and Xray transmission. With the available sensor resolutions and actuator systems that are available today sorting of minerals down to 2 mm size and up to 250 mm lump size is technically feasible. In industry, ore as well as coal is still hand-picked and current automation potential only utilised in a handful of specific applications. Recently a number of technological developments took place that may increase sorting potential, save mill costs and lead to lower overall tonnage costs.They are:??High speed and high resolution sorting systems based on X-ray transmission imaging??High speed on-line image processing and further development of advanced data processing??Modular multi-sensor automatic sorting units (using one or more sensors such as colour, electromagnetic and X-ray in a single device)??Sensitive electromagnetic sensors for sorting based on differences in magnetic susceptibility and electric conductivityThe above enables compact dry separation, insensitive for moisture fluctuations and at high separation sharpness, as well as “electronic” high gradient magnetic separation for larger particles. Besides conventional X-ray transmission (XRT), dual-energy XRT (DE-XRT) is now being redesigned to meet the requirements of the mining industry. The mentioned technologies provide automatic dry separation of minerals and rock as alternative for conventional processing."

Jan 1, 2005

By P. den Hoed, R. I. Rambiyana

"Four sulphide minerals - pyrite (FeS2), pyrrhotite (Fe1-xS), pentlandite ([Ni,Fe]9S8), and chalcopyrite (CuFeS2) - contain the base metals and most of the iron in concentrates of platinum group metals (PGMs). In the pyrometallurgical processing of PGM concentrates these sulphides form a matte during smelting, and iron and sulphur are removed from the matte during the converting process. This paper discusses the roasting of Merensky concentrate in air before smelting, with the purpose of reducing the matte load to the converter.Roasting tests were conducted in a bench-scale rotary kiln at temperatures from 350°C to 700°C. The concentrate tested contained 17.4% sulphur and consisted of 23% pyrrhotite, 16% pentlandite, 11% chalcopyrite, and 2% pyrite. The particles were fine (d50 = 22 µm), and all the sulphide particles were liberated. Roasting in air at 550°C and 650°C for 20 minutes removed respectively 60% and 70% of the sulphur. The iron in the sulphides was oxidized to Fe3O4 (magnetite) at temperatures below 500°C and to Fe2O3 (haematite) at temperatures above 550°C. At 700°C the bed sintered and copper oxides formed. At temperatures below 450°C oxidation was incomplete: pyrrhotite remained and only 30% of the sulphur was removed. Smelting tests were conducted to assess matte fall and the deportment of copper and nickel to matte. It was evident that roasting resulted in lower matte falls (a drop of approximately 60%) compared with matte falls from unroasted concentrate. The iron and sulphur levels in the matte were reduced to below 3.5% and 22% respectively.This paper also briefly describes the mechanisms by which pyrrhotite, chalcopyrite, and pentlandite are oxidized during roasting. For chalcopyrite, the mechanism proceeds through an intermediate solid solution phase, which extends from Cu1.02Fe1.04S2 to Cu2.04Fe0.72S2 to a copper-rich solid solution of bornite (Cu4Fe1.4S4-Cu2S). The oxidation of pentlandite proceeds through a monosulphide solid solution (Ni0.39Fe0.53S-Ni0.74Fe0.15S) to a solid solution of heazlewoodite ([Ni,Fe]3}xS2). These mechanisms are explored in relation to chemical thermodynamics and microstructures."

Jan 1, 2015

By T. G. Sieber, T. D. Tiemann

The extraction of quartz from siliceous iron ores by dissolution in sodium hydroxide solution has been described in detail in AIME Transactions. l923 data reported covered the temperature range from 230-416°F, where a continuous increase in the amount of silica extracted with increase in temperature was found. It is the purpose of this paper to describe some unexpected results of more recent work exploring principally the range of 500600°F where higher rates and greater amounts of silica extraction were antici-p ted. In brief, the experimental procedure consists in digesting the ore under pressure in solutions of sodium hydroxide, filtering the suspension and weighing and analyzing the dried residue for iron content. The amount of extraction is calculated from the weight loss or from the iron analysis of the residue and that of the original ore.

Jan 1, 1969

By James D. Nickerson

Thee Brightwater water treatment facilities, currently scheduled to be completed in 2010 and begin operating in 2011, will serve the northern part of King County, WA. The facility includes a new treatment plant and extensive conveyance system consisting of more than 21 km (13 miles) of influent and effluent conveyance tunnels and five portals. The majority of the conveyance system tunnels are mined by tunnel boring machines (TBM) and microtunnel boring machines (MTBM). Tunnel and portal construction is divided into three main contracts. The Ballinger Way receiving portal, constructed under the central tunnel contract, is the terminus for the BT-3 leg of the central contract and the BT-4 terminus of the west contract. The shaft has a 7.3-m (24-ft) finished inside diameter (ID) to accommodate removal of the central project TBM and the west contract TBM and extends to a depth of 66 m (216 ft) below grade through a complex and challenging soil profile characterized by multiple ground water tables. Vinci Grand Projects/Parsons/Frontier-Kemper Constructors (VCFK) was the joint venture team for the Ballinger Way portal. Frontier-Kemper was responsible for the shaft sinking. VCFK evaluated either slurry wall techniques or ground freezing for earth support during excavation of the portal and liner installation. The selection process took into account the vertical depth, cost, past practice, geology, water tables and a 9-m- (30-ft-) thick zone of contaminated soil at the top of the shaft. Ground freezing, which would also act as a hydraulic barrier, was deemed the better option for this project. The contract was awarded to New Jersey-based geotechnical contractor Moretrench. Typically, frozen walls, by design, key into an underlying cutoff. At the Ballinger Way portal, however, the [ ] freeze bottomed out in a substantially thick stratum consisting of predominantly clay, but with some inclusions of permeable soil that indicated significant ground water pressures. To ensure stable conditions at the bottom of the shaft, Moretrench, which also specializes in dewatering, designed and installed a perimeter array of deep wells to temporarily depressurize the permeable soils. The movement of ground water generated by pressure

Jan 1, 2009

By Stefan Aronsson, K. Rainer Massarsch

"ABSTRACT The geology of Sweden is characterized by the most recent glacial period with deposition of very soft clays and loose sand. Due to these difficult geotechnical conditions, new, innovative foundation and ground improvement methods were developed, which today are used in many other countries. Over centuries, Swedish scientists and engineers have made important contributions to the developments in foundation engineering. An important aspect of the success of Swedish foundation engineering in practice is the spirit of close cooperation between practitioners, engineers, and scientists. This has been achieved by the establishing of commissions, with the aim of finding solution of geotechnical problems. The paper focuses on developments in foundation engineering during the last century and does cover present activities in Sweden.IntroductionSoil mechanics and geotechnical engineering play an important role in Swedish society, as most construction activities require the consideration of foundation conditions. The objective of the paper is to summarize important developments in foundation engineering, primarily during the past century, which have influenced geotechnical engineering also in other countries. These achievements are the result of contributions by scientists, engineers and practitioners, only a few of which can be named. The paper does not claim to cover all aspects of geotechnical engineering, as emphasis is on the solution of foundation engineering problems from an international perspective. Thus, ongoing or recent research and development projects and activities within the geotechnical community are not included, as this would exceed the scope of the paper.Over the centuries, Swedish scientists and engineers contributed to the development of civil and foundation engineering. One important reason is the geology of Sweden, which is characterized by the most recent glacial period, resulting in the deposition of soft clays and loose sands in the coastal areas and dense glacial till in the interior of the country. Geotechnical engineering in Sweden has a long tradition and early contributions by several Swedish engineers and scientists have had a profound influence on the current foundation design in and beyond Sweden. A description of early Swedish geotechnical engineering has been presented in several publications by Flodin and Broms (1981), Broms and Flodin (1988), Massarsch and Fellenius (2012). The historic development of Swedish geotechnical and foundation engineering can be divided into four periods. During the “Early Era”, engineers were active in different sectors of military, civil, and mining engineering. Next, the “Industrial Era” comprised developments during the industrial revolution, when the transportation infrastructure of the country was modernized and extended. During the third period, possibly the “Golden era” of Swedish geotechnical engineering, which started at the end of the 19th century and lasted the following fifty years, geologists, engineers and scientists helped to establish modern geotechnical engineering. But also during the recent past, the “Modern Era”, several important contributions to geotechnical and foundation engineering which originated in Sweden, are used in many countries today."

Jan 1, 2014

By A. G. Merma

In this work, the electrocoagulation technique was studied in order to treat chemically stabilized concentrated oil-water emulsions. This study was mainly focused on the effects of operating parameters such as initial pH, current density, reaction time, electrode distance and inlet concentration on the separation of oil as measured by the chemical oxygen demand -1(COD) method. The synthetic emulsion was prepared from Shell - Talpa 30 oil (3g.L-1) and sodium dodecyl sulfate (1.0 g.L), having a Zeta potential around -70 mv at pH 8.7. The process was carried out in an electrocoagulation cell with a set of four parallel monopolar electrodes. This set consisted of two aluminum plate anodes and two 316L stainless steel plate cathodes. Kinetic curves showed that the electrocoagulation process exhibits three phases: (1) an initial phase, where the COD did not decrease because the solution had not reached the minimum amount of dissolved aluminum required to cause the break-up of the emulsion, (2) a reactive phase during which COD decreased due to possible agglomeration of the precipitates and (3) a steady-state phase where the COD did not change. The results showed that the period to reach the reactive phase decreased as the current density increased and the pH values decreased.

Jan 1, 2009

By Seal. Thom

Large heap leach operations around the world contain significant under-leached metal values that present recovery challenges to operators. The first challenge is to find the location of the highest inventory. High resolution resistivity ? has proven sensitive enough to detect such zones in the interior of heap leach pads to target treatment or re-leaching. Newmont Mining Corp. has adapted the high pressure fracturing technology, used in oil wells to stimulate select zones in heap leach pads to add reagents in 3-D for re-leaching, changing zonal chemistry for improved recovery and heap closure. High Resolution Resistivity ? is able to subsequently monitor injected solution flow and determine directional permeability during Hydro-Jex stimulation. The combination of these technologies has shown strong economic success, for selecting targets in the heaps and monitoring solution application. These technologies are now available to the mining industry for adoption.

Jan 1, 2008

By Larsson Lars-Erik, Rani Isa, Martin Jönsson, Håkan Bredenberg, Mats Larsson

"IntroductionSteel Core Piles are used extensively in Scandinavian countries, where hard rock is found within reasonable depths. A steel core is cast into a drilled steel tube casing and a rock hole is extended below the casing. This pile type is considered a very reliable type of pile, and for urban environment it has several advantages compared to other types of piles. One critical phase of the installation is the drilling of the casing. Usually a DTH (Down The Hole) hammer is used. Drilling in fine grained soils, e g silt, below the ground water level, may give rise to an excessive volume of soil material flushed up from the point of the casing, resulting in unacceptable settlements around the pile installation area.Using a new method for drilling of the casings, the ELEMEX-method has proven to significantly reduce the risk for such problems. In the paper a case record from a ground improvement project in central Stockholm is described. Ground settlements around the drilling area were carefully monitored over a longer period. Both the new drilling method and the conventional DTH casing drilling method where used, so that the corresponding ground settlements could be compared. Settlement records and comments are included in the paper.The paper also gives a description of the project. The installation of new piles and foundation constructions cover a whole city block in Stockholm downtown. The reason for the replacement of the old, damaged wooden piles were due to their destruction caused by a long time lowering of the ground water table. The paper gives a description of the new drilling method as well as an overview of usual urban foundation issues and their solution in Sweden, Finland and Norway.Drilled Foundation MethodDrilled Foundation, using drilling methods originally developed for drilling of large diameter rock holes, is today a standard method for the installation of piles, tiebacks, drilled pile walls and other foundation components, especially in urban built up areas where other techniques as drop hammers, augers, vibratory hammers and other equipment fail to meet the requirement, se ref(1). Drilled foundation is for example used for"

Jan 1, 2014

By Yoginder P. Chugh

Subsidence may be observed above partial extraction shallow room-and-pillar mines where the coal seam(s) is associated with weak and thick claystone in the floor. This paper presents results of subsidence studies at such a mine. During the 26-month study period, a time dependent subsidence causing a maximum vertical movement of 50 mn was observed. After a subsidence rate of 6.0-6.5 m/month for the first two months after development of mine workings, the rate decreased to 0.8-0.9 mm/month after 17 months. However, presumably due to settlement of barrier pillars, it increased therafter to 1.7 mm/month for the next 9 months. Angle of draw, based on zero subsidence, was calculated to be about 29 degrees. Maximum tensile strain and compressive strain values observed were 0.040 pct and 0.039 pct respectively. A hypothesis was fomlated to correlate surface subsidence movements with observed underground movments. The data collected to date fits reasonably well within the formulated hypothesis.

Jan 1, 1989

By John Reilly

Costs of complex/underground projects have been consistently underestimated and delivery on time and on budget has been problematic. This has been attributed, to inadequate cost estimates and unidentified and/or insufficiently managed risk. Use of probabilistic cost estimates like the Washington State Department of Transportation?s CEVP® process (developed by the author and others) has produced more realistic cost estimates, explicitly identified and quantified risk (as input to risk management plans) and early awareness of key project issues. This paper updates previous work (NAT 2004), adds implementation detail for probalistic cost estimating as used by WSDOT, FHWA and other agencies and will address key issues in risk management, as related to probalistic cost estimates.

Jan 1, 2008

By David S. Yang

The construction of Oakland Airport Roadway Project for the airport expansion requires stabilization of subsurface soils for the construction of three grade separation structures at two roadway interchanges and the intersection of a roadway and taxiway serving the airport. Loose sandy fills and soft Bay Mud were improved by Cement Deep Soil Mixing (CDSM) for the construction of a soil-cement foundation under the MSE (Mechanically Stabilized Earth) walls of a roadway overcrossing and a soil-cement gravity retaining wall to maintain stability of a roadway undercrossing during and after a major earthquake. CDSM was also used to construct two cutoff walls for groundwater control. A test section was carried out prior to full production to verify that the CDSM equipment, installation procedures, and mix designs could produce the soil-cement with required strength, uniformity, and permeability to meet the design intent. Additional test sections were performed for the confirmation or modification of the mix design and installation procedure to cope with the complex subsurface conditions resulting from the historical development of the site. The test section revealed that the CDSM cutoff walls, retaining wall, and foundation improvements could be constructed to satisfy the design requirements and that the intermittent test sections alleviate the impact of the varying subsurface conditions. Based on the data obtained from the test sections, one CDSM cutoff wall was completed in July 2000. Full production of the CDSM retaining wall, cutoff wall, and foundation began in March 2001 and is expected to be complete in November 2001.

Jan 1, 2001

By Gerald W. Longenecker

For decades, traditional hydraulic engineering approaches have been used for sizing stream channels when stream relocation efforts have been necessary to allow for the advancement of quarry and other surface mining operations. These approaches have been based on various ydraulic models to design channel cross sections and slopes that could pass the required regulatory design storm such as the 2-, 5, lo-, 25-, 50-, or even loo-year events. Designing the stream channel to handle these more extreme ,storm events would often lead to large channel designs which required extensive bank and channel bottom stabilization techniques including concrete, rip rap, gabions, or other expensive approaches. The constructed channels often required ongoing maintenance to remove accumulated sediment and other debris which would settle out and reduce the hydraulic capacity of the channel.

Jan 1, 1998

By Khosrow Ebrahimi

We document the occurrence, mineralogy and firing properties of magnesite from hydrothermal deposits in the upper Cretaceous ophiolites of Eastern Iran. These deposits occur as thin veins of nearly pure cryptocrystalline magnesite with only trace amounts of quartz, calcite, and dolomite. Ratios of CaO/SiO2 in the bulk ore are variable. The composition of dead-burned magnesite from these deposits, calcined at different temperatures and durations, is predictable from phase equilibria. Textures of the calcined magnesite were studied by SEM; results show that the principal impurites produced during calcination are forsterite, monticellite, merwinite, dicalcium and tricalcium silicates, and that these are located principally at triple junctions of the periclase crystals. The size of periclase crystals increased with temperature and duration of calcination and the amount of periclase-periclase grain contacts was reduced by increasing the concentration of impurities in the starting products. EPMA show: 1) that CaO and FeO contents in periclase increase steadily with an increase in the CaO/SiO2 ratio and the FeO content of the bulk ore, respectively, and 2) that limited solid solution exists between impurites. This study demonstrates that high quality dead-burned magnesia refractories can be produced from the Iranian magnesite with low CaO, SiO2 and FeO contents.

May 1, 2004

By F. E. du Plessis

"The distinction between data suitable for process control and data subject to aliasing only becomes quantifiable with the availability of rapid real-time measurements. Expecting the dynamics of flotation to vary for different ore types, process flows and equipment types; a study was conducted to compare the dynamics of different flotation processes. The results shed light on the critical sampling intervals required for process control which in turn allows process stabilization and optimization. The technology used for the in-line measurements is based on diffuse reflective spectroscopy and has been introduced into the mineral processing industry over the past ten years. It has been widely implemented in the sulphide flotation industry in South Africa for the real-time measurement of grade.BACKGROUND AND OBJECTIVE A study was conducted by Du Plessis and Keet (2010) to quantify the minimum sample frequency required for grade and/or impurity control. The study was based on chromite data collected at 15 second intervals from the concentrate line of a flash float cell in the Platinum industry. The data captured the natural process variation of the entrained chromite through water recovery due to changes in feed parameters and flotation performance. It was found that the minimum rate of sampling required from the studied flash float concentrate was 2 minutes. This sampling interval time accounted for 90% of the variance in the process data. It was further found that a sampling interval time of longer than 4 minutes produced data with no significant correlation to reality. The dynamics of the flotation process has been misjudged in the past but can be quantified with the availability of real-time grade measurement based on diffuse reflective spectroscopy. The objective of the study was to compare the dynamics of different sulphide flotation processes through the comparison of maximum sampling interval times required to combat aliasing. All data were collected from single stream analyzers that are currently installed at mineral concentrators. The technology used is based on diffuse reflective spectroscopy."

Jan 1, 2012

By Michael J. Beus

This Bureau of Mines report describes a tunnel stress relaxation gage (TSR) developed to measure initial radial displacement around full-sized underground openings. The TSR technique was shown to be a valid concept in previous field verification tests. Sensitivity has been improved by employing a titanium alloy cantilever in the transducer head, which also permits a deeper sensor location. Use of improved fabrication methods such as stainless steel bellows and sputtering techniques and use of an environmental chamber for testing greatly increased overall reliability. A miniature data acquisition system (DAS) was interfaced directly to the transducer for increased versatility and containment entirely within a borehole. The present TSR system is suitable for use around full-size underground excavations, particularly machine-bored openings. Field evaluation of the improved instrumentation verified the design goals.

Jan 1, 1978

By F. Bruey, T. Bruce, D. R. Nagaraj, W. Thomas, P. Riccio, E. Guitard

"AEROPHINE® 3418A Promoter is a flotation collector that has been an industry standard in the Canadian mineral processing industry since its first commercial use at the Kidd Creek concentrator in 1980. Its wide range of applications in sulphide mineral flotation has made it successful, specifically in the processing of complex sulphide ores which contain copper, lead, zinc, and silver or any combination of these elements for selective separation.AEROPHINE® 3418A Promoter is a unique, phosphine-based collector originally developed for the flotation of copper sulphide minerals and activated zinc minerals. It is now recognized for its selectivity for complex, polymetallic sulphide ores and porphyry copper ores. In addition, AEROPHINE® 3418A Promoter is highly selective for copper, lead, activated zinc, nickel and precious metals. AEROPHINE® 3418A Promoter exhibits strength yet, selectivity against iron sulphides (pyrite, pyrrhotite, marcasite, and arsenopyrite), non-activated sphalerite, and many minerals which contain penalty elements.This paper outlines a brief history of the product’s development, its historical use in Canada and several potential innovative mineral processing applications with the use of the chemistry. Three Canadian case studies will be presented on various ore types including: a Cu-Au ore, a Cu-Zn ore, and Cu-Pb-Zn ore. A plant production update will also be given on the future supply of AEROPHINE® 3418A Promoter.INTRODUCTIONCytec Industries Inc. operates a phosphine derivatives plant in Niagara Falls, Ontario, that manufactures various products for their speciality chemicals division. The products from this site are based on phosphine (PH3) chemistry and are used in a variety of markets including electronics, agriculture, LED lighting, water treatment, metal extraction, and mineral processing. One of the major products is the phosphine-based sulphide mineral collector, AEROPHINE® 3418A Promoter.AEROPHINE® 3418A Promoter (Figure 1) was originally developed for the flotation of copper and activated zinc minerals (Thomas, 2010).."

Jan 1, 2015

By Lorrie Fava

Two needs in the mining industry, to enable overall process improvements, are open systems and network connectivity in underground mines. The Pando project, a collaboration between Symboticware, Vale and Xstrata Nickel, and supported by CEMI, addresses these issues, and leverages the solution platform to deliver intelligent applications. An open system is one that uses publicly available standards for its key interfaces. Vendor-neutrality and ease of information flow are two main benefits that result from the use of open systems. By facilitating the interoperability of systems, open systems allow information to be available when and where it is needed for decision support. Network connectivity in underground mines is typically limited, with hotspots in strategically chosen areas that are relatively static. Mobile equipment moving through a mining work cycle experiences intermittent connectivity; in this situation, seamless remote equipment monitoring is impossible. The Pando project establishes an open technology platform, adhering to the IREDES and OPC UA standards. It enables the collection and integration of information generated by mobile equipment? seamlessly while there is a network connection, and as a store-and-forward gateway to manage intermittent connectivity. The platform capabilities are leveraged to support embedded intelligent applications. This open platform, the SymBot, is a rugged hardware and software device. The platform complies with open standards for industrial automation and systems interoperability. The SymBot platform is capable of providing advanced real-time decision support at the device level, and is designed to be remotely configurable. Applications being developed through the Pando project include engine monitoring, a dynamic load weighing system, machine location monitoring and automated activity monitoring including production and maintenance reporting.

Oct 1, 2010

By D. L. Pitt

This paper, describing the milling methods at the concentrator of the Premier Gold Mining Co., Ltd., Premier, B. C., Canada, is one of a series being prepared by the United States Bureau of Mines on milling methods and costs in the various mining districts throughout the United States and Canada. ACKNOWLEDGMENTS The authors wish to acknowledge the assistance and suggestions given during the preparation of this paper by the engineering staff and accounting department of the Premier Gold Mining Co., Ltd., all of whom have assisted materially in gathering the data used.

Jan 1, 1933