Search Documents

During the drilling campaign conducted between October, 1942; and May, 1943, to prove the extent of the scheelite deposit worked by King Island Scheelite N.L. at Grassy, King Island, Tasmania, 35 holes were drilled and 606 samples recovered and assayed for their content. Of these, 238 came from outside the limits of the orebody and were for the most part barren, although a few contained some scheelite. The present statistical analysis is made only of the 368 samples taken from diamond-drill cores of the orebody itself.Drilling Pattern and Sampling MethodsFrom the purely statistical viewpoint, it is realised that methods employed in selecting sites for diamong.-drilling, and of collecting samples from drill cores, do not give a completely unbiassed set of data for analysis. Fig. 1 is a sketch plan showing the relativepositions of the drillholes, which were inclined at an angle of depression of 50 deg. The pattern does not conform to a properly randomized and' regularly-spaced grid, the positions of the later holes being determined by the results obtained from previous holes.Statistically, the bias is, therefore, favourable. The unequal spacing of the drill holes and the lack of uniformity in direction of the lines along which the holes were drilled are unsatisfactory from the mathematical viewpoint; but it is realised that these irregularitiesare difficult to avoid in determining by the most economical methods the extent of such an orebody, and are dictated by geological rather than mathematical necessity.Sampling, also, is lacking in complete uniformity. Each sample is approximately 10ft. in length. However, owing to the fact that 100% recovery of core is rarely achieved, and actual lengths of samples taken are ,primarily governed by the length of the drill runs,and secondarily by lithological changes, there is a considerable amount of variation in the sample length.AssayingWith the exception of 28 samples from three drill holes all samples dealt with in this paper were assayed in the Melbourne University Ore-Dressing Laboratory of the Commonwealth Scientific and Industrial Research Organisation. These assays were given to the nearest 0.05% WOg as it was considered that more accurate determination was not possible. This fact has been taken into consideration in the frequency analysis below. The 28 assays determined by the Tasmanian Mines Department were given to the nearest 0.01%.

Jan 1, 1950

By B. P. Watson

Crush pillars have been incorporated into a mechanized, low-profile trackless system at South Deep Gold Mine. These pillars had to be designed to fail near the face and to ensure that pillar failure is contained within the pillar, to avoid bursting and the risk of high loads being generated during a seismic event, respectively. PoweRite backfill bags were recommended to maintain the integrity of the pillars; except in the main access drives, where the sidewalls were to be supported on 5.6 mm diameter weldmesh and yielding anchors. The results of a trial site investigation exceeded expectations, showing a residual pillar strength of about 37 MPa for a newly formed pillar and 8 MPa for a pillar subjected to seismicity and a closure of more than 300 mm. The introduction of these pillars has improved the rock mass conditions because of the active nature of the support, compared to the previous passive backfill method. Importantly, the pillars have increased mining efficiencies and improved face availability. A potential cost saving to the mine of R140.9 million could be realized over a period of 10 years.

Jan 1, 2014

By Forrest T. Moyer

Need for lightweight building materials was created in the latter part of the nineteenth century by a radical change in building design in which dead load or structural weight was transferred from thick, heavy, load- bearing walls of former construction practice to a load-carrying framework of beams and columns with thin walls. This new design was brought about by the introduction of structural steel followed by reinforced concrete and structural concrete as materials for the erection of the load-supporting frame. The new materials and method of construction made possible the erection of skyscrapers and the building of bridges with long spans, and made feasible additions of one or more floors to existing buildings. As size and design of the load-bearing framework are controlled chiefly by dead load, the natural result was a. search for and use of light- weight materials in partitions, floors, and exterior walls. However, these thin walls created problems of heat and sound. insulation, so that building materials which possessed good heat- and sound-insulating properties in addition to light weight were objects of extensive research. One group of materials developed to fill this need comprised lightweight concretes, of which some were obtained by the use of lightweight aggregates. Although the advantages of lightweight.materials were evident from the first skyscrapers, there was a transition.stage.between the old bearing- wall and modern skeleton-frame types of building, with the heavy and massive construction of the former superimposed upon the latter. Hence, it was not until the period between 1910 and 1930 that the new lightweight concretes were recognized and used more extensively in the erection of large, nonresidential buildings. From this type of construction, light- weight-aggregate concretes entered-fields of residential and small non- residential building; in which they were found desirable for production of prefabricated, large-size; masonry units. Although the weight of each unit was reduced sufficiently to enable one man to handle it easily, properties of the new concretes other than light weight were the principal factors in the ready acceptance of these new materials in residential building. Manufacture of precast units includes complete lines of masonry and back-up blocks, bricks; floor beams, columns and partition, roof, and floor tiles and slabs. Recent improvements in casting machinery, development of the vibration-pressure machine, and a more thorough study and knowledge of the requirements and properties of the concrete mix have all contributed materially to the rapid expansion in use of lightweight aggregates in this industry.

Jan 1, 1942

By J. Krzyzanowska

Paper written on project work carried out in partial fulfilment of Bachelor of Engineering-Mining Venetia Mine, an open-pit diamond mining operation in the Limpopo Province of South Africa, currently has a mixed haul truck fleet consisting of Caterpillar 785B and C; 789C; modified 793D and 793D. Even in an ideal situation these trucks have different cycle times, which causes queuing at the loading area and their different speeds cause bunching on the ramps, leading to higher overall cycle times and lower productivity. This problem was identified but the root causes of the problem were not investigated and quantified. A time and motion study on the haul trucks was thus undertaken to measure actual cycle times and compare them to ideal cycle times as well as to observe any reasons for deviations. Ideal cycle times are partly evaluated on the basis of simulation and partly from production optimization expert input. Several areas that affect production were identified and these include: haul road conditions, the control room, dispatching programme and dispatching data management, as well as truck-shovel matching. The investigation was important in establishing control parameters for haul fleet operation since time spent queuing is production time lost, which defers waste tonnes to later in the life of mine, thus decreasing the tempo at which kimberlite is exposed.

Jan 1, 2007

By S. Agarwal, S. Frimpong

The creation and maintenance of a healthy working environment in surface mining operations require sustained efforts in pursuing advanced research initiatives toward the development and deployment of powered haulage technologies. This paper contains progress summary on a frontier research in truck dynamic control, vision and collision avoidance. This research is required to provide solutions to challenging problems regarding operator visibility in truck haulage in a surface mining environment. The paper focuses on truck control kinematics and dynamics, truck-haul road interactions, intelligent truck sensing, intelligent truck collision avoidance system, integrated system for situational awareness, augmented visualization and operator interface, and field testing and error variance modeling of developed technologies. A sensor suite of four subsystems, including front-side stereo-camera, front-side Doppler radar, close range sonar proximity sensors, and rear-side camera system have been recommended for developing a 360° truck operator vision to allow safe operations. This research initiative is significant because it will provide a strong basis for developing technologies to improve truck haulage safety in surface mines and construction sites.

Jan 1, 2007

By J. G. George

A brief review of the silver industry is presented to set the stage for the analysis of the distribution of silver production by source from various types of mines in Canada and of the changing relationship between the total output of silver and the total output of base metals. The decline in the average grade of the Canadian mines is also discussed and a trend for the future is proposed. The report then examines in broader aspects the world primary silver production and concludes, in the section on outlook, that the effective supply in primary silver will grow at a rate significantly lower than the growth rate expected for base metals. A cumulative deficit of some 900 million ounces is projected for the period 1975-1980 and a further deficit of some 1,100 million ounces if projected for the 1980-to-1985 period.

Jan 1, 1977

By F. E. Chase

Mobile roof supports are shield-type support units mounted on crawler tracks. Mobile roof support (MRS) units are used during retreat mining, and they eliminate the setting of roadway, turn, and crosscut breaker posts which are required during pillar recovery operations. Mobiles are a more effective ground support than timbers, and their usage enhance the safety of section personnel and reduces material handling injuries. MRS usage is rapidly increasing, and approximately 40 U.S. coal mines have successfully employed this relatively new technology. This paper is in response to increasing requests from operators, State and Federal Regulatory Agencies, and others on the practical aspects of MRS usage in underground coal mines. During this investigation, nearly half of the U.S. mines which have utilized mobiles were visited. This report depicts the more common pillar extraction methods which operators have found successful. The Christmas tree and outside lift methods are illustrated and discussed. Roof control plans that do not require breaker posts or allow pillar extraction with fewer than four mobiles are also examined. In addition, operators' experiences with setting pressures, loads, and rates of loading during pillar extraction are addressed. Mining and support strategies to more effectively control hillseams, weak roof, and gob overrides which have entrapped equipment are also discussed.

Jan 1, 1996

By R. L. Virta

Editor?s note: Each year, the June issue of Mining Engineering features an industrial minerals review. Several people put in a fair amount of time in developing the material for this issue. Thank you to the industrial minerals annual review editor, to the technical committees chair and vice-chair, and to the authors of the individual commodity profiles. Jim Norman, member SME, of GeoTrans Inc., is the industrial minerals annual review editor. Abani Samal, member SME, of Pincock Allen & Holt, is chair of the industrial minerals technical committees. Technical committee vice chairs include: ? Abani Samal, member SME, of Pincock Allen & Holt, agricultural minerals. ? Aaron McMahon member SME, of Pincock Allen & Holt, ceramics and refractories ? Bradley S. Van Gosen, member SME, of the U.S. Geological Survey, chemical raw materials. ? Mark Zdunczyk, member SME, of Continental Placer Inc., construction materials. ? Jerry Gauntt, member SME, of Marston, fillers and pigments. ? Michael Cheshire, member SME, of Indiana University, sorbents, filters and process aids. ? Candace Trimble, Oil-Dri Corp. of America, specialty minerals. Their help makes possible this June industrial miner-als issue. On behalf of ME readers, the editors thank them. Ball Clay Four companies ? H.C. Spinks Clay (owned by Lhoist Group), Kentucky-Tennessee Clay (owned by Imerys Group), Old Hickory Clay, and Unimin Corp. ? mined ball clay in four states in 2008. Production, on the basis of preliminary data, was 964 kt (1.1 millon st) with an estimated value of $45.3 million. That was a 10- percent decrease in tonnage from 1.07 Mt (1.2 mil-lion st) with a value of $49.2 million that was produced in 2007. Tennessee was the leading producer state with 63 percent of domestic production, followed by Texas, Mississippi and Kentucky. About 73 percent of production was airfloat, 16 percent was crude and 11 percent was water-slurried.

Jan 1, 2009

By D. Harrington

Probably over 95 percent of the coal production of the United States depends upon the use of explosives before it can be placed in the railroad car at the mine, and up to the present time it has been impossible to obtain Pry kind of practicable explosive that isn't dangerous unless handled carefully. In other words, no "foolproof" explosives have been found to date and inspection of the accident records of the coal mines of this country indicates that the use of explosives in coal mines has taken a sad toll of lives. ACCIDENTS PROM EXPLOSIVES IN COAL MATES Of the 2,000 to 2,500 persons killed annually in the coal mines if the United States, 100 to 125 have been killed from explosives without an explosion of gas or dust; these accidents have been due to misfires, hangfires, premature blasts, or accidental setting off of explosives through carelessness or otherwise (but chiefly through carelessness in some form). In this type of accident the flame character of the explosive is not necessarily involved, although an unexpected or premature blast is initiated much more easily with black blasting powder, which has a long flame, than with a permissible explosive, which has a flame much shorter and of briefer duration. By far the greater number of such accidents are caused by black blasting powder or dynamite rather than by permissible explosive.

Jan 1, 1936

By N. V. Nayak

Maharashtra State Road Development Corporation Ltd., has initiated a scheme for construction of 55 flyovers in Mumbai in India. To ensure speedier completion of projects several new technologies were adopted to save time without compromising on safety and reliability. Many of the flyovers involved large diameter pile foundations carrying loads ranging from 3500kN to 1375kN. Significant time would have been lost in using conventional load testing procedure to check pile capacity apart from the difficulty in mobilizing the load and the obstruction to site movement and traffic on the adjoining roads. High Strain Dynamic Testing was introduced on the project sites in lieu of static load testing after conducting numerous co-relation studies on various project sites. A total of seven co-relation studies have been conducted till date and based on these data static testing has been replaced by dynamic testing on numerous flyovers. The paper presents the results of such studies. CAPWAP analysis was also conducted on the data to evaluate the percent skin friction and end bearing so as to improve future design parameters.

Jan 1, 2000

The Fraser Range is composed dominantly of basic pyroxene granulites derived from basalts, many of which appear to have been vesicular and pillowed. Acidic and basic garnet-bearing granulites are important in the west, and acidic granulites and narrow anorthosite layers are dominant in some regions east of the Fraser Range. An extensive flat-lying olivine gabbro sheet cuts the granulites, and in places has been converted to spineI-bearingmeta-gabbros and pyroxene granulites. The granulites of the Fraser Range (Proterozoic) are separated from the gneisses and schists of the goldfields regions (Archaean) by the Fraser Fault, over which there is a large gravity anomaly (gradient 20 milligals per mile). Some of the problems associated with the concentration of Cu, and Ni liberated from mineral lattices during metamorphism, and other principles of metal concentration in granulite terranes, are discussed. The recognition of vesicular and pillowed zones, even though highly metamorphosed, is of fundamental importance.

Jan 1, 1969

By Linney, Robert J.

REPUBLIC Steel Corporation's iron-ore properties in the Adirondacks consist of mines, mills, and sintering plants in the Mineville and Port Henry area and at Lyon Mountain. This article will deal with the properties in the vicinity of Mineville and Port Henry. In 1938, when Republic leased the Mineville- Port Henry operations from the Witherbee Sherman Corp., these properties had just come through some hard depression years. As a result, the mine development program was far behind schedule; most of the equipment needed replacement; and above all, the entire system of mining had to be completely changed to reduce operating costs. The concentrator had been in operation for many years; the process was dry and dusty. Machinery and equipment were either badly worn or entirely obsolete. The sintering plant, also long in operation, was badly in need of repairs.

Jan 1, 1943

By W. W. Roepke

The Bureau of Mines has developed an interactive computer program that enables mine operators and others to identify the effect of cut-ting system changes on relative dustiness at the face. The program, which simultaneously evaluates machine parameters, coal seam parame-ters, and operator-controllable parameters, was developed for use on any microcomputer using BASIC programming language. The program allows the user to change one or more of the cutting system parameters at a time to see how these changes affect relative dustiness. A complete program listing and flowchart are included along with operating in-structions and sample outputs. An example showing how to use the program is also included.

Jan 1, 1985

By Nan C. Jensen

Modern high-temperature metallurgical processes have created a demand for raw material for furnace parts and lining that not only will with-stand high temperatures is but will not react with the substance being melted in the furnace. Spark-plug insulators, laboratory ware, tanks for the glassmaking making industry, and saggers and kiln furniture for the chinaware and pottery trades also must be made of materials hat have high melting points. Among the minerals that can be employed for such refractory uses ore those commonly known as the "sillimanite group' -kyanite, andaluste, sillimanite, and dumortierite - and the allied minerals topaz and pinite. Consideration of the occurrence, properties, qualities, uses, and sources of supply of these commodities and the markets for them constitute the subject of this paper. General Features of Kyanite and Related Minerals Kyanite, andalusite, and sillimanite ire composed of three elements - aluminum, silicon, and oxygen ? and are called aluminum silicates. The have

Jan 1, 1943

By Wouter Hartman

Xuandong Coal Mine is mining coal in one of the most challenging underground environments in the world. This work has found that it is not only challenging but it also has the composition for some interesting rock mechanics and ground control conditions. The paper highlights the extreme mining and rock mass behavior conditions encountered when mining coal at 900 m below surface. It was found that the ground control environment associated with geological weakness, low coal material strength and stiffness, was reasonably well controlled; however, the chain pillar geometry and design did not take these geological weaknesses into consideration. Some of the chain pillars employed were quite large, which resulted in floor punching and secondary floor heave, which causes extreme difficulty for production. No barrier pillar has been employed except for the center 164-m-wide main headings pillar with a w/h ratio in excess of 40. After assessing the location and geometry of a 200-m-thick dolerite sill overlaying the coal measures, we found the probability of it breaking up into to smaller fragments and producing a larger goaf to be low. Therefore, the influence of the dolerite sill on chain pillar loading is considered small compared to the low coal, immediate floor and roof rockmass strength. It is further recognized that horizontal stresses could be locked up within the dolerite sill, which would likely result in regional bending that would be distributed through the chain pillars. This has, to some extent, already occurred, and the effects have been seen and felt through excessive floor heave, pillar punching, and coal bumps (seismicity). We?ve also found that there was a need to employ basic rock mechanics principals in assessing the stability of future multiple seam mining layouts.

Jan 1, 2012

By James G. McKelvey

Owners have seen several major tunnel projects in recent years fall victim to a general reduction in the number of bidders as well as an erratic range of pricing. It should be noted though that this is not a universal trend and some projects have seen good competitive bids. Contractual terms and conditions are an important factor in attracting good competition. The Front End documents of tunnel projects have come under increasing scrutiny as tunneling contractors in the U.S. industry are looking much more closely at their risk exposure in the contract terms and conditions. Considering the amount of tunnel construction work upcoming in North America, it is important that General and Special Conditions are put together in a way that provides a reasonable basis to execute the Contract and also provide a fair, balanced and swift way to resolve disputes.

Jan 1, 2008

By Ivette E. Torres

Aruba, formerly a. part of the Netherlands Antilles, separated on January I, 1986, and became an autonomous part of the Netherlands. Full independence of the island from the Netherlands is scheduled for 1996. In this chapter, however, Aruba's statistics are included with those of the Netherlands Antilles. Tourism continued to be the main industry of the island, which continued to depend heavily on imports, mostly from the United States. During the year, the Government was preparing legislation to regulate the exploration of oil deposits in the relatively shallow sea around Aruba.

Jan 1, 1989

By Dean Lindsay, Inna Dymov, Mariam Melashvili, Jim Smolik, Chris Fleming

"This paper presents results from the proposed cyanide detoxification circuit for Seabridge Gold’s KSM project. The proposed flowsheet uses a two-stage CCD (counter-current washing/decantation) circuit to transfer the flotation products CIL(carbon-in-leach) barren solution to a SART process (Sulphidization, Acidification, Recycling of precipitate, and Thickening of precipitate) to recover copper and free cyanide from the copper cyanide complex. The SART barren solution is then treated by an AVR process (Acidification, Volatilization of HCN gas, and Reneutralization) to concentrate the cyanide that was liberated in SART for recycling to leach. The washed CIL barren pulp (the CCD underflow) is treated with the SO2 /Air process to oxidize residual cyanide.The goal of this complex flowsheet is to recover and recycle as much cyanide as possible and produce a final effluent containing less than 0.5 mg/L copper and CNWAD at the lowest cost. The SO2/air process is capable of achieving low residual CNWAD (<1 mg/L) in the final product, but the persistence of aqueous copper above the target level has been detected in the treated solution in some instances. The expected high concentrations of copper and cyanide in the KSM CIL barren ( >200 mg/L each species) and the difficulties this might create for the SO2 /air process was a key factor in the decision to consider including the washing, SART and AVR steps in the project flowsheet.The target concentrations of CNWAD and Cu were readily achieved after aging the SO2 /air treated pulp, as would occur in a tailing or polishing pond. This suggests no additional treatment will be required to sustain low levels of these species in the final plant effluent."

Jan 1, 2015

By W. C. Phalen

The production of salt in the United States divides itself at the outset into two distinct classes…

Jan 1, 1915

By Timothy A. Clancy

To help reduce the Nation&apos;s dependence on imported chromite, the Bureau of Mines is conducting research on the use of dolomites as an alternate material. Dolomite is a plentiful domestic resource and offers certain advantages as a refractory raw material. A review of the literature has indicated that there are many sources of high-purity dolomite in this country and that European nations use a greater proportion of dolomite refractories, primarily in steelmaking, than the United States, The Bureau of Mines characterized 14 domestic dolomites as to chemistry, density, mineralogy, microstructure, and thermal behavior, to develop baseline data on their suitability as refractory raw materials.

Jan 1, 1983