Search Documents

By Daryl W. Wurster

The Liberty Bridge in Greenville, South Carolina is a curved, cable-stayed, pedestrian bridge with primary support provided by two towers. The bridge is part of the Falls Park redevelopment. The bridge was originally designed to be supported on drilled piers. Alternately, the bridge was supported on a combination of micropiles and anchor piles because of difficult access and subsurface conditions. The use of micropiles and anchor piles led to improved construction scheduling and reduced costs. Micropiles were used to resist compressive loads. Anchor piles were used to resist tensile forces and to eliminate excessive settlement of pile caps into underlying fill during pre-stressing. This paper describes the site history, bridge construction, site and subsurface conditions encountered, and the decisions that led to support of the bridge using micropiles and anchor piles and foundation construction.

Jan 1, 2006

By K M. Brodie, D I. K McLeod, J Ruddock

Environmental incidents involving mine tailings and waste rock inevitably become highly publicised and serve to damage the credibility of the entire industry. The recent serious incident involving a spill from a Romanian mine, was blamed for triggering æone of the worst environmental catastrophes in Eastern EuropeÆ. It is important to clearly demonstrate to the general public that these incidents are not representative of the industry as a whole. Where such incidents have occurred, the causes are generally related to poor design and/or construction, inadequate supervision and/or monitoring and maintenance, lack of independent expertise, inadequate risk identification and treatment and no provision to ensure that rehabilitation and long term management of the site occurs. Many people are unaware that these issues have been considered and provided for at the Martha Mine. Despite the fact that the first tailings storage facility has performed very well over fifteen years of operation, the long term safety and security of the tailings storage facilities continues to be questioned and debated by the public. The best way to address this is to provide quality information to enable a better understanding amongst the general public.

Jan 1, 2002

By E. S. Schubert

Keywords: co-generation, furnace CO-gas cleaning, disintegrator scrubber, Theisen In a closed, electric, reduction furnace, no oxygen enters the furnace from the surrounding environment. The off-gases are thus not ?burnt? and therefore contain a considerable amount of CO and H2. Traditionally these gases have been captured and burnt in a flare stack. Recent developments have led operators of such furnaces to revise this strategy and to consider utilising these gases as a fuel for gas-fired generator sets to produce electricity, thus becoming more energy efficient. On 31 March 2010 the new emission standards, in accordance with the Air Quality Act, Act 39 of 2004, were promulgated. The minimum emission standards according to the act require that the particulate matter emissions from the primary fume-capture systems on closed furnaces for ?new plants? in ferroalloy and calcium carbide production not exceed 50 mg/Nm³ and 25 mg/Nm³, respectively. By implementing co-generation, the producer automatically complies with the new environmental emission standards for an off-gas. As much as 30% of the electrical power cost, which is set to double in the near future, can be saved by partly generating one?s own electrical power. In December 2010, the National Treasury published a discussion paper for public comment, one entitled ?Reducing greenhouse gas emissions: The carbon tax option?. Irrespective of how the tax is finally implemented, it will result in an increase of production costs in affected industries. This paper focuses on the characteristics of a furnace-off-gas cleaning system for closed ferroalloy smelters, characteristics that meet the requirements of both reducing solid-matter emissions and operating a safe and reliable gas plant.

Jan 1, 2011

By Alexey Lozhko

The technical-and-economic furnace exploitation indices are considerably influenced by the system of heat utilization. In the situation of total output decrease works are forced to exploit furnaces at the partial loading, sometimes even at the idle running for the sake of steam production. The furnace exploitation in this regeme is known to cause the increase of the heat portion, taken away together with waste flue gases. The losses can be partially compensated at the expense of heat exchange efficiency development in the recuperator or heat-exchanger. One of the well-known methods, characterised by high efficiency and low expenditures is the intencification of the heat exchange process by the means of pulsation method.

Jan 1, 2006

By Y Lanwin

The Australian mining sector is undergoing a significant transformation with the adoption of advanced technology to the operational landscape. This has highlighted a critical disconnect between our traditional educational systems and the skill requirements of working with these advanced technologies. This paper aims to provide a behavioural science analysis of how the traditional manufacturing mindset, deeply rooted in our educational frameworks from primary to tertiary education, registered training organisations (RTOs), and in-house learning and development, is misaligned with the needs of today’s technologically advanced mining operations. Originating in the industrial revolution, the manufacturing mindset prioritised efficiency, mass production, and the division of labour. In educational institutions, this translated into an emphasis on rote learning, linear examinations, and a rigid adherence to processes and procedures. Such a system, while effective in producing a workforce suited for repetitive and predictable tasks, falls short in fostering skills like problem-solving, adaptability, flexibility, and coping with change – skills that are increasingly vital in a mining sector dominated by automation, robotics, and AI. The paper discusses how the focus on disciplined adherence to standard work procedures and processes in educational and training programs has inadvertently stifled creativity and autonomy in learners. This issue is compounded in the workplace, where employees, having been conditioned to operate within strict guidelines, now face the challenge of adapting to environments where autonomous decision-making and creative problem solving are crucial. In essence, the traditional approach to education and training has prepared individuals for a world of work that no longer exists. This paper advocates for a whole of pipeline approach, grounded in behavioural science, to revamp mining education and training. It highlights the importance of understanding and influencing the behavioural aspects of learning and recommends for an approach that promotes diversity, critical thinking, and adaptability, preparing the workforce to excel in the rapidly changing landscape of the Australian mining sector.

Sep 1, 2024

By J L. Mauk

Golden Cross is a volcanic-hosted, low-sulfidation, epithermal Au-Ag deposit in the Hauraki Goldfield. Irrespective of the rock type (andesite versus dacite), hydrothermally altered wallrocks are enriched in K, Rb, As and Sb around Au-Ag mineralised veins of the Empire vein system and stockwork. Sodium and Sr are strongly depleted around these veins, whereas Mg and Fe are locally depleted. Calcium and Si display mixed behaviour, varying from unchanged to depleted to enriched. Other elements including Al, Ti, Mn, Zr, Y, and Nb show little change or are immobile during hydrothermal alteration. Element enrichment and depletion trends are directly related to the degree of alteration and the alteration mineralogy. Addition of K and Rb and converse loss of Na and Sr in intensely altered wallrock surrounding veins corresponds to the replacement of igneous plagioclase by hydrothermal adularia. Sodium and Sr occur in moderately altered rocks on the margins or in æhard barsÆ that contain plagioclase. Locally, elevated Si concentrations and depletion of Mg adjacent to the Empire vein system reflects intense silicification of the wallrocks and the replacement of mafic minerals by quartz rather than by chlorite. The geochemical zonation patterns at Golden Cross are very similar to those at the McLaughlin deposit California, and shallow levels of the active Broadlands Ohaaki geothermal system. Therefore, determination of K, Na, Rb, Sr, and Ca enrichment and depletion patterns provides insight into alteration intensity and mineralogy that is complimentary to traditional trace element analysis of As, Sb, Hg, Au, Ag, Zn, and Pb used in the exploration of shallow level (< 500 m) epithermal Au-Ag deposits.

Jan 1, 2000

By William R. Yernberg

SME’s Arizona Conference was held at the Doubletree Hotel at Reid Park in Tucson on Dec. 5and 6, 2004. The annual conference is organized by the Arizona Conference Board of Directors, which represents SME sections in Arizona and adjacent areas. The conference provides an opportunity for individuals and corporations associated with mining in the region to get together each year to discuss the status of the industry. The meeting featured a keynote address and more than30 technical papers. Two years ago, the U.S. copper industry was facing on a run for two years now,” and “both precious metal and base metal prices are going up.” The increases in metal prices were attributed to development in China and other Asian countries. “With a population of 1.6 billion, China has recently created 80 million jobs,” said Silver.

Jan 1, 2005

By Tex M. Kubacki

In 2007, the University of Utah Seismograph Stations (UUSS) temporarily expanded its seismic monitoring network in Emery County, Utah, in response to the August 6 Crandall Canyon mine collapse that trapped six workers. In spite of this additional coverage, no seismic events were located in the area during a six-day period (gap) from August 8 to August 13. The Mine Safety and Health Administration (MSHA) ?Command Center Log Books? however, contain references to 16 instances of underground ?bumping? and ?bouncing? that occurred during the gap. When ground truth information provided by the log books is compared to the raw seismic data recorded by the UUSS network, the correlation offers insight into the chronology of mininginduced seismicity (MIS) in the aftermath of the collapse. The new research focuses on identifying and locating seismic events that occurred during the six-day gap using double-difference relocation techniques and correlating them with log book ground truth. Ten seismic events were identified in the vicinity of the mine during the six-day gap, ranging in magnitude from coda magnitude (MC) 0.5 to 1.4. Three of these events were amenable to location by double-difference techniques. The location of one of these events is directly confirmed by ground truth information from the log books. As a result of this new research, the accuracy of Crandall Canyon double-difference locations has been improved, and the number of events correlated with ground truth information has increased. The seismic events occurring in and around the collapsed area appear in two distinct sections of the mine?east and west of the center of collapse. It was originally reported that the post-collapse events occurred in episodic clusters. The first two episodes occurred to the east, followed in time by a cluster on the west, and then by a third episode on the east. With the addition of new events to the data set, this pattern is no longer as clear, although the events still occur in clusters. Only one MIS cluster was found to occur within the bounds of the minimum estimated collapse area (Pechmann et al., 2008).

Jan 1, 2012

By W. P. C. Duyvesteyn, B. J. Sabacky

Reprinted with revisions from Extractive metallurgy of copper, nickel and cobalt, volume I: Fundamental aspects. ed. Reddy R.G., Weizenbach R.N. Warrendale, Pennsylvania: The Minerals, Metals and Materials Society, 1993. Development work on the Escondida process, concluding with the successful operation of an integrated leach-SX-EW pilot plant and a pilot flotation plant for the upgrading of leach residues, demonstrated that all major process objectives could be achieved. Extraction of 40% of copper in concentrates containing monovalent copper was achieved with essentially no oxidation of sulphide sulphur. The Cu contents of leach residues from four different types of concentrate were successfully upgraded to the original feed grades, giving a product that has potential as a high-quality concentrate for the smelter market. A compact solvent extraction section effectively recovered the ammonia lixiviant for recycling to leaching and selectively transferred Cu into a conventional acid sulphate electrowinning system. High-quality "six-nines" copper cathode was produced on commercial-scale stainless steel blanks, demonstrating that the process will be able to compete effectively in the premium cathode market

Dec 1, 1995

By James W. Weaver

The 2,120-foot long cable stayed Penobscot Narrows Bridge that carries US Route 1 over the Penobscot River between Verona Island and Prospect, Maine is supported on four foundation units, one below each pylon and one at each abutment. Due to varying subsurface conditions along the bridge alignment, the structure was designed to be supported on foundations consisting of high-capacity steel H-section piles (Verona Pylon), a mat bearing on a prepared bedrock surface (Prospect Pylon) and spread footings bearing on compacted rockfill (abutments). The 70-foot by 80-foot (plan area) Verona Pylon foundation was designed to be supported by 288, 430-kip design capacity steel H-section piles (HP14x117, 50 ksi steel) driven through up to 100 feet of dense glacial till deposits containing cobbles and boulders up to 3 feet in diameter. The piles were installed using a single-acting diesel hammer (Delmag D62-22) with a maximum rated energy of 165 kip-ft. Thirteen representative piles were selected for dynamic testing (ASTM D-4945) to verify pile capacity, hammer efficiency and pile stresses. Dynamic testing determined that four different pile driving criteria were needed across the site due to variation in the bedrock and soil resistance below the footing plan area. Approximately 4 percent of the production piles were damaged/rejected due to misalignment and/or damage as a result of encountering the cobbles and boulders embedded in the glacial till. The rejected piles were located randomly throughout the plan limits of the foundation mat. Subsequent structural analyses indicated that the foundation was capable of safely supporting the design loads without the need for installing replacement piles. Evaluation of dynamic testing results with signal matching and pile driving records provided valuable information on pile side and tip resistance. Evaluations were made regarding predicted versus actual pile lengths, pile bearing material, distribution of skin friction and end bearing capacities.

Jan 1, 2011

Construction of the Boddington Mine 130 km (81 miles) southeast of Perth, is about 89 percent complete. When the $2.9-billion development is finished, it will be the largest gold mine in Australia, producing 31 t/a (1 million oz/year), according to project majority owner Newmont Mining. Newmont?s acting regional group executive for Asia Pacific, Philip Stephenson, told a gold conference in Australia that the project would be ?the biggest thing for Newmont this year.? The project has been in the works for more than 10 years, but because of a three-sided ownership and fluctuating gold prices, it struggled to get started. However, Newmont is set to become the full owner of the project and is moving ahead on the low-grade project. ?We are targeting annual production of 31 t/a (1 million oz/year) for each of Boddington?s first five years. When it is in full production, Boddington will be the largest gold mine in Australia,? Stephenson said. ?The mine?s costs applicable to sales will be around US$9.64/g (US$300/oz) and that puts Boddington into the bottom quartile of the global cost curve. ?Strategically for Newmont, Boddington coming on-line will improve Newmont?s overall global geopolitical risk profile as it delivers greater exposure to an AAA-rated country.? Boddington has a projected mine life of 20 plus years. It has current total reserves of 622 t (20 million oz) and rising. Stephenson said Boddington has the largest reserve base of all gold projects in production or those that are about to go into production in A-rated countries or better. And it will be an important asset for many years to come. Newmont will acquire the remaining 33 percent share held by AngloGold Ashanti in a deal that should be concluded in the next two months. Australian miner Newcrest Mining Ltd. had exited the joint venture several years ago. Newmont had come into the project through the take-over of then Australia?s leading gold miner Normandy Mining, while AngloGold Ashanti gained entry through

Jan 1, 2009

By Valérie Léveillé

As new legislation drives to lower SO2 emissions from metallurgical plants, plant managers face the challenge of keeping their costs under control. The Cansolv® SO2 Scrubbing System has been broadly adopted in the non-ferrous industry as a cost effective solution for smelter operators to meet the new SO2 emissions targets. The Cansolv® SO2 Scrubbing System is an amine-based regenerable process that selectively absorbs SO2 from a variety of gases, including dilute smelter gases, such as furnace and converter gases. The system produces a pure, water-saturated SO2 byproduct stream, which can then be directed to the front end of a sulfuric acid plant for conversion to sulfuric acid. When deployed in a smelter complex, the Cansolv® SO2 Scrubbing System may also be used to process acid plant tail gas, allowing single absorption sulfuric acid plants to achieve emissions an order of magnitude lower than that of a double absorption acid plant with a lower capital investment. Depending on inlet gas temperature SO2 emissions in the treated gas can be controlled to as low as 55 mg/Nm3. This paper will describe some of the applications where customers have or are planning to use the Cansolv® SO2 Scrubbing System and what as well as which features and cost advantages for the treatment of smelter gases were key to the technology choice.

Jan 1, 2009

By R. Heuberger

South Africa?s Mining Industry operates in an uncertain world. The industry is buffeted by problems regarding retrenchments, unemployment, low productivity, rising costs, volatile exchange rates, commodity prices and government regulations. With these uncertainties facing the decision makers, what does applied technology offer the industry?s management? Modelling languages with risk analysis have been available for decades, but in the past their use has been very expensive, requiring large mainframe computers and lots of computer time. Today, PCs and laptops have incredible power, which makes interactive risk analysis affordable and viable for all enterprises, whether small or large. ?What is risk analysis? ?What is Monte Carlo simulation? ?What kinds of computer models need to be created to use risk analysis and Monte Carlo simulation effectively? This paper addresses these questions and illustrates, with a practical example in the mining industry, how risk analysis techniques can be used to support decisions in the climate of uncertainty.

Jan 1, 2005

By William R. Bond, Jim V. Rouse

Introduction The pressure/vacuum (p/v) lysimeter or soil water sampler has become useful for monitoring vadose zone or unsaturated zone water conditions. The soil water sampler was first introduced around 1961. It was used as a monitoring and research device for studies in agriculture and soil contamination around landfills. Since then, it has been used for many purposes. The use of p/v lysimeters at mining facilities to monitor for solution loss is a relatively new idea. The primary purpose of the lysimeter here is to function as an early warning system. It detects leakage through liners of tailings ponds, heap leach pads, and leachate holding ponds. Their use has proven valuable for collecting baseline data and detecting loss of precious leachate fluid. Different lysimeter designs are capable of vadose moisture sampling from near the surface and down to 90 m (300 ft). They are also capable of sampling soil moisture or saturation plume contaminants from areas not accessible by conventional water well installations. The most common installations are usually simple and cost-effective. In many cases, they can be installed without the use of heavy drilling equipment. A properly placed and installed lysimeter can detect solution leaks in several days or weeks. A conventional perimeter monitor well may take months or years to detect a leak of the same magnitude. A discussion on the general design and installation of p/v lysimeters will give an understanding of its versatility. Three case studies of lysimeter installations at mining sites will be examined in detail. Design, Installation, and Sampling Design The basic design of a p/v lysimeter chamber consists of a porous material through which the soil is drawn into a collection chamber. Access tubes run from the unit to the sample station at the ground surface. Most units currently available range from 25 to 76 mm-diam (1 to 3 in.-diam). The sample collection chamber, or body, can vary from 0.6 to 1.8 m (2 to 6 ft) in length. The body can be constructed of PVC casing or Teflon, depending on the installation desired. The collection chamber functions as a holding reservoir for the collected soil moisture. The intake, or porous material, on the lysimeter is the most complex and vulnerable portion of the unit. The pore size selection varies based on the needs of the installation, type of fluid to be sampled, and type of soil material surrounding the unit. Teflon (PTFE) and porous ceramic are used in fabrication of the porous inlet portion. When using a Teflon material, which is hydrophobic, a larger pore size of 70 µm is needed to overcome surface tension and draw water into the collection chamber. It is typically used at sites involving organic contamination, because of its inert properties. Ceramic material is generally hydrophilic, having less surface tension. Therefore, it has a smaller porosity range to conduct the moisture through the porous medium while under vacuum. Pore sizes may be selected from 0.16 to 6 µm, and can be manufactured for the specific needs of the installation. The final major design component of the p/v lysimeter is the access or sampling tubes. The tubes are usually of 6.3-mm-outside-diam. (0.25-in.-outside-diam). They are made of rigid polyethylene or flexible Tygon with a wall thickness of 1.5 mm (0.06 in.). The con-

Jan 4, 1985

Techniques have been developed for the dissolution of a wide range of rocks and minerals by a sodium peroxide sinter process. A olarge number of elements are determined by atomic absorption spectroscopy, and other elements such as arsenic and sulphur are determined by chemical analytical methods. The methods adopted to overcome inter-element and ionization effects on the atomic absorption results are discussed.

Jan 1, 1974

By Lee W. Abramson

Performing risk analyses on tunnel projects has become common place and on many projects it is required from an owner or regulatory perspective. After the project is planned, designed and constructed, the data concerning identified risks, assumptions, costs, probabilities and mitigations is generally long forgotten and buried in some file somewhere. A study was performed comparing predicted risks versus actual events on several recently constructed tunnel projects. Probabilities and costs for selectively common risks on tunnel projects have been studied and re-evaluated. Conclusions are presented that can guide future projects and the veracity of the tunnel risk analyses performed.

By Robert J. Maron, Mark Fernald, Alex Van der Spek, O’Keefe. Christian, Tim Bailey

"Sonar array-based non-invasive flow measurement technology is becoming an accepted and many times a preferred method of measuring challenging single and multi-phase flows in the mineral processing industry. This fundamental sensor and measurement technology has been extended to two developments that provide new measurement capabilities useful for monitoring and managing slurry flows and pipes.The first development is the non-invasive measurement of real-time velocity profile of slurry flow in horizontal pipes. Multiple non-invasive passive sensors measure localized velocities and are combined to provide a velocity profile measurement. This information can be used to determine the approach and onset of solid deposition on the bottom of the pipe. Having this information in real time can enable operation at lower velocities and/or higher solids concentration while avoiding solids deposition or plugging and its associated operational costs.The second development is the non-invasive measurement of pipe wear on slurry lines. Presently, such measurements are made by hand-held portable ultrasonic thickness gages. The numerous shortfalls associated with the manual method are overcome with a set of permanently or semi-permanently installed transducers clamped onto the outside of the pipe. This ring of sensors contains a series of conformable ultrasonic transducers spaced around the circumference, which are used to measure the thickness of the pipe under their respective locations. Compared to manual methods, this system and approach results in better repeatability and accuracy. It also decreases inspection labor costs and pipe access requirements. The minimal accuracy variations in the presence of varying environmental temperatures will be shown. Trending of pipe wall thicknesses in high wear pipelines will be illustrated. The benefits of significantly improved pipe wear monitoring in hydrotransport lines with abrasive solids, and associated improvement in the ability to insure safe operation and avoidance of costly environmental damage due to leaks caused by pipe wear will be discussed."

Jan 1, 2009

By Woodcock J. T

During the dissolution of gold in fully aerated cyanide solutions the CN ion is the active agent, and consequently the usual method of evaluating the dissolving power of such solutions is to determine the CN- concentration analytically. The presence in the solutions of copper and/or zinc which themselves form complex cyanides, may result in erroneous conclusions as to the free cyanide ion concentration determined by titration.In this paper the theory of titration of such solutions has been developed, and potentiometric methods have been used to follow the behaviour of complex cyanides of copper and zinc. The results for cuprocyanides show Cu (CN)s to be the most important copper complex, and in addition they explain the reported low rates of solution of gold in copperbearing solutions which when titrated in the usual way, appear to have adequate free cyanide. An explanation of the misleading value of the titration is given, and suggestions for recognition of the condition are offered. Preliminary results for zinc-bearing solutions show that there is no satisfactory end-point for the titration of CN- in excess of that in the complex Zn (CN) 4=, which dissociates to CN and Zn(CN)g-.

Jan 1, 1950

By L. Westerstrom

Supply and Demand After a dismal first half, the industry saw a marked improvement in its markets during the final six months of 1983. Domestic consumption was 17.6% higher in the second half of the year, primarily due to a surge in electric power requirements. The sharp increase in demand for electric power during the third and fourth quarters afforded utilities the opportunity to lower stocks that had accumulated to record levels during 1982. Consumer stocks were reduced from 179 Mt (197 million st) at the end of June to 153 Mt (169 million st) by the end of the year. That is the largest inventory drawdown on record during a six-month period without a major coal strike. Despite the huge depletion in inventories, coal production in the second half of 1983 rose 1.3% above output in the second half of 1982. However, because of the disappointing first half, production in 1983 totaled only 712 Mt (785 million st), 6.4% less than the 760 Mt (838 million st) produced in 1982. Demand The extent to which the economic recovery affected coal markets in 1983 varied: • total domestic coal consumption increased 4.2%; • electric utility coal consumption increased 5.3%; • exports declined by about one-fourth; • coal consumption at coke plants declined 9.5%; and • coal consumption in the other industrial sectors increased 2.9%. Domestic coal consumption totaled 667 Mt (737 million st) it 1983, 27 Mt (30 million st) more than 1982. Electric utility consumption increased from 539 M1 (594 million st) in 1982 to 567 M1 (625 million st) in 1983. Coal consumption at coke plants declined from 37 Mt (41 million st) to 34 M1 (37 million st). Residential and commercial use increased 181 kt (200,000 st) - from 7.4 to 7.6 Mt (8.2 to 8.4 million st). Electric Utilities: Electric power generation increased 3.1% in 1983. Demand for electric power increased in all major consumer categories. Residential and commercial use rose 2.7% and 3.3%, respectively. The most striking increase, however, and indicative of the economy's strong upturn, was the increase in industrial electric power use. Industrial power requirements, which declined 9.8% in 1982, rose 4.1% in 1983. The electric utility sector continued to expand its use of coal last year while lowering its requirements of oil and natural gas. In 1983, electric generation from coal increased 5.7%, while genera-

Jan 5, 1984

By D. Brand

"The risk management objective of the AMIRA Code of Practice for Metal Accounting has seldom been systematically investigated in the literature up to the authors’ knowledge. Risk is defined in the Australian Standard on Risk Management (AS/NZS 4360:2004), as “the chance of something happening that will have an impact on objectives”. The simplified economic analysis performed in this paper has lead to define “something happening” as measurement non-representativity and “impact on objectives” as NSR loss from the optimal NSR. This has pinpointed a missing link being the establishment of a relation between NSR in flotation plants and measurement representativity. The proposed framework, referred to as the total cost of representativity, answers the previously unanswered question of how much accuracy/reproducibility is fit for purpose in a given flotation plant. Authors readily acknowledge that it is way easier to assess the cost of accuracy/reproducibility than the cost of inaccuracy/irreproducibility. However, this exercise not only answers previously unanswered questions but also establishes an essential link with operational excellence. This paper exposes why such operational excellence could neither be attained nor proved without a state of the art metal accounting system. This should impact not only how metal accounting systems are audited/designed/refactored, but also how flotation plants are designed.IntroductionBecause representative metal accounting is a vital source of information for the financial accounts of a mining/metallurgical company, the need for a code on metal accounting was recognized in 2001 and a team was formed in 2003, under the sponsorship of several major mining houses, to produce such a code. Table 1 exposes the two main objectives of this AMIRA Code of Practice for Metal Accounting."

Jan 1, 2017