Search Documents

By R. L. Whiting, H. J. Ramey

The basic study from which this paper was prepared was started as the result of the growing need throughout the world for increasing quantities of energy in all forms. Quite obviously, natural forms of energy that are readily available at low development cost are those in greatest demand. The underdeveloped countries — and particularly those having little or no petroleum resources — are the countries in which the most interest is being shown in the newer energy sources. One of the least expensive energy sources is natural geothermal steam.'-* Although this form of energy has been recognized for centuries, it has been only during the past 20 years that serious efforts have been made to harness it. Natural geothermal steam energy in Italy, New Zealand, Mexico, Japan, and California is now being produced through wells to drive turbines and generate electricity. Further, active exploration for natural geothermal steam is being conducted in Hawaii, Fiji, Taiwan, Chile, Russia, Greece, and Katanga. It is surprising to find that most geothermal steam exploration is in the "steam seep" stage. That is, surface studies are made and exploratory wells are drilled in the general area of steam seeps. However, in the larger geothermal steam areas, there have been efforts to apply the most modern geological and reservoir engineering principles in order to define the reservoir parameters, particularly those relating to estimates of reserves and future productivity. This paper is concerned with the development of appropriate equations and techniques to facilitate these estimates. Production of natural steam or hot water presents problems different from those experienced in the production of oil and gas. For example, steam or hot water systems may be essentially single-component systems, while hydrocarbon systems are most frequently multicomponent fluid systems. Heat effects are much larger for water than for hydrocarbon systems; and the natural steam production may or may not be isothermal, while production of petroleum reservoirs is considered normally to be isothermal. Petroleum reservoir engineering principles may be applied to natural steam or hot water reservoirs if the inherent differences in the systems are considered. The basic considerations involved in geothermal steam reservoir engineering are: thermodynamics, physical and thermal properties of water, materials and energy balances, fluid influx, and performance matching and predicting. Thermodynamics Fig. 1 is a pressure-temperature diagram for the liquid-vapor region for pure water, showing the critical point and five other points representing possible initial conditions for a geothermal steam reservoir. To generate a physical appreciation for the mechanics of natural steam production, it is helpful to consider

Jan 1, 1970

By 1980, the U.S. mining community had reached a broad consensus regarding coal pillar design. The pillar load could be estimated from tributary area theory, and the pillar strength from empirical formulas and laboratory coal strength testing. Then the growth of longwall mining required new thinking. Recently, powerful design methods have emerged from analysis of large data bases of real-world pillar successes and failures. These include the Analysis of Retreat Mining Pillar Stability (ARMPS), the Analysis of Longwall Pillar Stability (ALPS), the Mark-Bieniawski rectangular pillar strength formula, and guidelines for preventing massive pillar collapses. Sophisticated numerical models have also helped transform the pillar design landscape. In the process, our understanding of pillar mechanics has been greatly enriched.

Jan 1, 1999

Autogenous-Carrier Effect and Gangue Influence in Fine Particle Flotation of Ilmenite/Titanaugite System

Sep 13, 2010

By E. C. Morton

The Western Australian School of Mines (WASM) has developed a facility for the static testing of large scale ground support elements. The samples are loaded using a mechanical screw feed jack. Instruments measure the displacement and the load being applied. Methods have been developed for testing of mesh, shotcrete and membranes. Mesh samples are restrained on all sides and loaded centrally. A new large scale punch test method has been developed to evaluate shotcrete and membranes. These products are sprayed on to a sandstone substrate containing a centrally located isolated disc. The sprayed product is loaded by displacing the disk. The different test methods are described in detail. The test program involved two types of mesh, several shotcrete mix designs with different curing times and one membrane product. The force-displacement responses are used to directly compare the products. The implications for implementation of the different ground support products are discussed.

May 1, 2009

By James H. Cobbs

The utilization of large diameter drilled holes for mine shafts seems to have had its beginning in Europe about 1850 (28) where the mining industries of Germany and The Netherlands first used drilled shafts. Recent shafts in softer formations of diameters as large as 25 feet and as deep as 1, 700 feet have been drilled in both The Netherlands and Germany. The first shaft drillers utilized cable tool or churn drilling techniques which limit both hole diameters and drilling speeds. Though some churn drilling of shafts is still performed, rotary drilling has been the dominant technique for many years.

Jan 1, 1973

By F. M. C. C. Vieira

Four mining alternatives for exploiting an ultra-deep orebody were assessed through a multidisciplinary evaluation process which involved: the generation of a 3D geological model; the design and scheduling of life-of-mine layouts; the analysis of anticipated ventilation and cooling conditions; the study of rock-related risks of mining in ultra-deep stress environments; the logistic implications of transporting men, rock and materials; and, lastly, the economic implications of each option. Once results from the integrated mine design assessment were available, mine planners were faced with an important problem to solve: how to identify the optimal mine design alternative when numerous assessment measures and multiple decision criteria needed to be considered simultaneously? To address this ‘multiple-attribute decision problem’ and arrive at the ‘optimal layout for ultra-depth’, a generic decision methodology that uses principles of ‘utility’ was applied. The methodology assumes that ‘single-value risk estimators’ do not account for the inherent variability of real conditions. Therefore, risk estimators were represented by statistical distributions of their incremental changes, where applicable. The stochastic variables, once defined, are used as inputs in the ‘utility’-based layout decision scheme. This ‘utility’-based decision methodology offers a framework for mine design decisions to be made objectively, when complex trade-offs between multiple risk domains need to be considered simultaneously. Upon applying it, one of the layouts emerged as the preferred alternative. Keywords: Utility; mine design; multiple-attribute decision; layout selection

Jan 1, 2003

By Jay C. Hanson

Various electrical and electromagnetic (EM) geophysical techniques are currently being evaluated by the U.S. Bureau of Mines for their effectiveness in the detection and monitoring of electrically conductive (1 to 5 S/m) lixiviant (leach solution) to depths of 600 m, either above or below the water table. These techniques include magnetotellurics (MT) , controlled source audiofrequency magnetotellurics (CSAMT), resistivity and focused resistivity, ground-penetrating radar (GPR), frequency-domain electromagnetics (FEM), and time-domain electromagnetics (TEM). Of these techniques, TEM may be the most effective, but CSAMT and focused resistivity also hold promise. Geophysical computer modeling of the borehole TEM technique was conducted based on an idealized geoelectric section (layered earth) with characteristics based on the Santa Cruz porphyry copper deposit near Cas a Grande, AZ. Layer resistivities and thicknesses were obtained from geophysical data and geologic logs available from the site. Modeling of borehole TEM in both preleach and during leach situations was conducted. Simulating the TEM method using computer modeling proved to be encouraging since there were substantial differences between leached and nonleached responses. The modeling does not prove the effectiveness of TEM in the field, but does indicate that detection of deep lixiviant zones is theoretically possible.

Jan 1, 1992

By E. H. Rose

This paper, describing the concentrator practice of the Moctezuma Copper Co., is one of a series being prepared by the Bureau of Mines. The Nacozari concentrator of the Moctezuma Copper Co. (the Mexican subsidiary of the Phelps Dodge Corporation) is located about 75 miles south of Douglas, Ariz., in the Moctezuma District of the State of Sonora. Nacozari is the southern terminus of the Nacozari Railroad, ever which all concentrate is transported to Douglas for smelting.

Jan 1, 1930

By J. B. Hedrick

In 2004, rare earths were not mined in the United States. The major supplier, Molycorp, continued to maintain a large stockpile of rare-earth concentrates and compounds. Major uses for these commodities were in automotive catalytic converters, petroleum fluid-cracking catalysts, permanent magnets, glass-polishing compounds, ceramics, metal-alloying additives, phosphors and rechargeable batteries. Consumption of refined rare-earth products decreased. The United States was a major importer and exporter of rare earths in 2004. Yttrium was not mined or refined in the United States in 2004. Imports from China, France and Japan accounted for most of the U.S. supply of yttrium compounds for refined yttrium products.

Jan 1, 2005

By S. Frimpong, S. R. Dindarloo

Material handling in open pit mining accounts for about 50% of production costs. The selection and deployment of efficient, safe, and economic loading and haulage systems is thus critical to the production process. The problems of truck and shovel selection and sizing include determination of the optimal number and capacities of haulage and loading units, as well as their allocation and operational strategies. Critical survey and analysis of the literature has shown that deterministic, stochastic, and experimental approaches to these problems result in considerably different outputs. This paper presents a comprehensive simulation framework for the problem of truck and shovel selection and sizing based on the random processes underlying the network-continuous-discrete event nature of the mining operation. The framework builds on previous research in this field and attempts to address limitations of available methodologies in the form of a comprehensive algorithm. To test the validity of the framework a large open pit mine was evaluated. The stochastic processes governing the uncertainties underlying the material loading and haulage input variables were defined and built into the stochastic model. Discrete event simulation was used to simulate the stochastic model. The proposed model resulted in several modifications to the case study.

Jan 1, 2015

By P. K. Sahoo, C. R. Ray, S. S. Rao

Good operation of Soderberg electrodes is dependent upon high quality electrode paste coupled with better electrode management procedures. Without having a good electrode operation, it is not possible to obtain the best outcome from the furnace. In other words that is a good way to say how important the proper electrode operation is. Good electrode performance depends on the slipping rate and current levels, which decides the shape of the baking curve at the level of just below the contact clamps. Negative curvature of baking zone in the central part is considered dangerous because shrinkage takes place outwardly creating abnormal stresses in the electrode. Soft breakages occur when the baking zone comes below the clamps and the casing cannot take the current. This paper deals with various factors affecting baking characteristics leading to soft breakages and also presents case studies in a closed 48MVA furnace with smelting for charge chrome. In case studies in a closed furnace, it has happened that the energy for baking at the low current operation before breakage has been lower than the actual slipping has demanded. At low current there should not be problem, but a problem can occur when the current for some period is raised above the current carrying capacity of the casing. So data for electrode operation in actual period was studied and presented in this paper.

Jan 1, 2007

By D Crequer

Land rehabilitation at Golden Cross is reviewed, 8 years after mine closure in 1997/98, from the perspectives of a Peer Reviewer (land rehabilitation) and a Regional Council Officer (Resource Consents compliance). Land rehabilitation items we discuss include: management of restored pastures, native plantings (on-site riparian and block plantings and off-site environmental riparian enhancement plantings), wetlands (on-site tailings lake and sediment ponds littoral zone plantings, and basement of the open pit; and off-site wetlands enhancement plantings), pine plantations on-site and on surrounding land, stabilization of the Tailings Lake Embankment (landslide) and Open Pit capping, capping of acid-mine-rock, stability of discharge channels, buildings and amenities, public access for recreation, educational uses, and future management of the site. Pest control has helped to conserve the rare and endangered HochstetterÆs (Leiopelma hochstetteri) and ArcheyÆs (L. archeyi) frogs, and a regionally significant stand of rare swamp maire (Syzygium maire) has been conserved and fenced.

Jan 1, 2006

Jan 1, 2005

By Vladimir G. Kochnev

Crushing and grinding account for the major portion (60 to 80 percent) of the overall expenses for ore processing. Autogenous (AG) and semiautogenous grinding (SAG) have been considered a step forward in comparison to conventional grinding circuits with several stages of crushing and using ball (and/or rod) grinding mills (Bassarear, 1982, MacPherson, 1989, Pithois, Casalis, 1983, Maripuu et al., 1983). However, there remains room for improvement to existing AG and SAG technologies and both technologies have immense economic benefit potential. Experience gained by the Technics & Technologies of Disintegration Ltd. (TTD) in the research of grinding processes shows that grinding in AG and SAG mills can be performed in a more effective way. The company's approach comprises the following elements: ? Novel mill design. ? New liners and lifters. ? Novel discharge grid design. ? Technique of treating material of critical particle size. Comparative tests that demonstrated the usefulness of these innovations are described in this article. Currently, there are hundreds of AG and SAG mills in operation throughout the world. Application of new internal elements of the mills and reconsideration of the circuit design of the existing grinding equipment using present technological solutions would significantly increase the throughput rate and diminish power requirement.

Jan 1, 2008

By Gerald M. Bandholz

Exxon Minerals Company, a division of Exxon Corporation, has been exploring for base metal deposits in the Precambrian volcanic rocks in northern Wisconsin since 1970. Aerial electromagnetic surveys of the area, conducted in 1974, reported an anomaly, near Crandon, in Forest County. In the summer of 1975, the first diamond drill entered the anomaly, representing the 25th prospect Exxon had drilled in Wisconsin. This first hole revealed significant mineralization containing zinc and copper. Subsequent drilling confirmed the discovery of a sizeable zinc-copper massive sulfide are body. 1.1.2 Location The deposit is located in northeastern Wisconsin within a topographical high called the Northern Highlands region. The deposit lies about 5 miles directly south of Crandon and about 2 miles east of State Highway 55 on Sand Lake Road (see fig. 1). Other local communities include Rhinelander 28 miles west, Antigo 45 miles south, and Iron River and Iron Mountain, in Michigan, 75 and 44 miles east and north of Crandon respectively. In relation to the lakes and streams, the deposit lies 0.25 miles north of Little Sand Lake, and about 1 mile south of Swamp Creek.

Jan 1, 1981

By Ji-He Wei

Keywords: stainless steel, AOD refining, side and top combined blowing, mixing characteristics, water modeling The fluid mixing characteristics in the bath during the side and top combined blowing AOD (argon-oxygen decarburization) refining process of stainless steel have preliminarily been investigated on a water model unit of a 120 t AOD converter. The geometric similarity ratio between the model and its prototype (including the side tuyeres and the top lances) was 1:4. On the basis of the theoretical calculations for the parameters of the gas streams in the side tuyeres and the top lances, the gas blowing rates used for the model have more reasonably been determined. The influence of the tuyere number and position arrangement, and the gas flow rates for side and top blowing on the characteristics has been examined. The results demonstrated that the liquid in the bath underwent vigorous circulatory motion during gas blowing, without obvious dead zone in the bath, resulting in a well mixing effectiveness. The gas flow rate of the main tuyere had a governing role on the characteristics, a suitable increase in the gas flow rate of the subtuyere could improve mixing efficiency, and the gas jet from top lance could make the mixing time prolong. Corresponding to the oxygen top blowing rate specified by the technology, a roughly equivalent and good mixing effectiveness could be reached by using six side tuyeres with an angle of 27 degrees between each tuyere, and five side tuyeres with an angular separation of 22.5 or 27 degrees between each tuyere. The relationships of the mixing time with the gas blowing rates of main-tuyeres and sub-tuyeres and top lance, the angle between each tuyere, and the tuyere number have been obtained.

Jan 1, 2005

By J. J. Montoro

The influence of blasting on the excavators’ efficiency, defined as mucking rate (amount of rock mucked per unit time) and mean bucket load (amount of rock loaded in each bucket operation), is investigated. Rock characteristics, blasting parameters (drill pattern, explosive energy, and charging), and the excavator’s performance (truck loading time and number of buckets to fill a truck) were monitored in eleven blasts in an open pit iron ore mine. ANFO, ANFO/emulsion blend, and watergel were used in the blasts and the powder factor was varied between 0.98 and 1.45 kg/m3. The mean bucket load is mainly affected by the bucket size, which is independent of the blasting parameters. Besides the relation with the mean bucket load, the mucking rate was found to be positively correlated with the explosive energy, whereas no significant correlation with the rock properties was found. The analysis of the data, together with other published works, suggests a non-monotonic relation of the mucking rate with the powder factor, with a maximum mucking rate at a certain powder factor. This is especially true when the useful work of the explosive per unit rock volume is used rather than the classical mass powder factor and when only the amount of explosive above grade is considered.

Jan 1, 2007

By Graham Davey

"Ultrafine grinding of minerals has been in wide spread use in the industrial mineral field for over 30 years. Within the last 10 years the metalliferous industry has shown interest in the ability to produce ultrafine particles, as chemical, physio-chemical and physical separation processes have advanced to be able to treat ultrafine metalliferous particles. Also as the primary mineral deposits are depleted, new more difficult deposits must be mined. Existing operations are also looking to maximize economic return from existing deposits, requiring new thinking and technologies.The recent development of industrially proven and cost efficient technologies for ultrafine grinding has opened up another processing option for the treatment of finegrained metalliferous and refractory gold ores. The current commercial designs are variations of stirred mills used in the industrial minerals sector for the past 30 years. For the purposes of this paper ultrafine grinding is considered to be P80 of less than 15 microns.Attrition milling to fine grind sizes presents some challenging issues relating to scale-up including the dearth of information on the quantitative impact of feed and operating conditions, as well as the precise and accurate measurement of particle size distributions. Two examples from recent installations will be analyzed including Thalanga Copper and Century Zinc Mines. Both have diverse grind size targets for the SMD, yet both have realized significant metallurgical gains."

Jan 1, 2002

Laboratory electrical resistivity measurements of rocks are reviewed. Inductive and galvanic methods are discussed together with the ten important experimental factors which should be considered in an investigation.These experimental factors are electrodes, sample preparation, measurement errors, temporal current variations, current density, frequency, electrolyte composition, electrolyte saturation, pressure, and temperature.

Jan 1, 1969

Tin mineralization in both eastern and western Tasmania shows a spatial correlation with middle Palaeozoic biotite granites and adamellites. The range of composition of these granitic rocks is restricted with respect to Mg, K, and Na content. Because this compositional restriction is shown by granitic rocks from other tin provinces, the concept of a genetic relationship between these granites and the associated tin mineralization is reinforced, and similar concentration mechanisms may be involved.Gold mineralization is largely restricted to eastern Tasmania and in contrast to the tin mineralization is rarely spatially associated with the middle Palaeozoic granitic rocks, although most authors have suggested a genetic correlation with hornblende and/or biotite granodiorites.Although few analyses are available, the granodiorites that are spatially associated with gold deposits exhibit similarities to granitic rocks from gold provinces elsewhere. These features suggest a possible genetic relationship between gold mineralization and the granodiorites.The composition of granitic rocks may be used as an aid to exploration in delineating areas of potential tin and gold mineralization in granite terrains.

Jan 1, 1970