Search Documents

By T. G. Carter, R. I. Miller

First, the influence of variation in the

Apr 1, 1995

By Levent Ozdemir, Bjorn Nilsen

For several recent TBM tunnel projects, unexpected ground conditions have been encountered, causing extra cost, considerable delay, and in some cases major claims. Undoubtedly, insufficient and/or irrelevant site investigation and testing are among the main causes of such incidents. The purpose of this paper is to review the main investigations and tests relevant for hard rock TBM projects, with particular emphasis on the considerable development that has taken place over the last few years. Also, guidelines for defining optimum scope and extent of site investigations and testing are discussed, as well as the importance of adjusting the investigations and tests according to complexity of the ground conditions and project type.

Jan 1, 1999

By Lowell Stroud

This report is the third in a series presenting equilibrium vapor-liquid data for helium-bearing natural gases. The first two reports contained phase data for the gases processed for helium at the Bureau of Mines Amarillo and Exell, Tex., helium plants. The present report offers similar information for a lower-helium-content (0.75 mole-percent) natural gas to be processed in the Department of the Interior's long-range helium-conservation program. A windowed-cell apparatus was used to obtain 218 samples of equilibrium vapor and liquid phases at 73 experimental conditions ranging in temperature from -100° F to -275° F and in pressure from 100 to 500 psi. From the phase data, the condensation characteristics, helium solubility, and equilibrium-vaporization-coefficient data for helium, nitrogen, and methane were evaluated. The effect of using a. preliminary hydrocarbon trap upon the subsequent vapor-liquid compositions is reported. A brief comment regarding the composition effect of passing the gas through a gasoline-removal unit is also included.

Jan 1, 1963

By N. L. Hayward, V. H. Ness

In the past decade Australia has seen the development, construction and commissioning of three complex processing plants for the treatment of lateritic nickel ores. These have all been based on high pressure acid leaching (HPAL) for extraction of nickel and cobalt into solution, followed by solid liquid separation in a CCD circuit. However, flowsheets for separation and purification of the nickel and cobalt diverge markedly. The existing plants have been commissioned with varying degrees of success, with a variety of problems ranging from materials of construction to inadequate design. While the process problems are not insurmountable, there is much room for improvement. Currently there are several new HPAL plants at the feasibility or financing stage. All of these have adopted one of the existing flowsheets. Most of the enhancements have focused on increasing autoclave size. It is now time to assess the success and failures of the three existing plants and incorporate this experience in a design for productivity, efficiency and reliability. Towards this end, this paper discusses aspects of flowsheet optimization, materials of construction and engineering design.

Jan 1, 2001

By Malcolm Scoble, Jean-Marc Robert, Luciano Piciacchia

"An approach to the in situ testing of mine backfills is outlined. It has been developed to provide a measure of the effective strength and stiffness of such materials after placement in stopes. This paper is based upon recent field studies undertaken at five Quebec mines. Details of the selected instrumentation, supporting equipment and testing procedures are reviewed. The mechanical behaviour of the backfills is reported and related to their physical properties. This approach represents an economical, simple and reliable means to assess the mechanical characteristics of backfill materials as an aid to both mine design and placement quality control. IntroductionDevelopments in backfill and mining method technology are creating a pressing need to develop effective techniques for characterizing the physical and mechanical properties of backfill in situ, rather than relying on traditional laboratory testing. The development of bulk mining methods is creating the requirement to more fully understand the nature of exposed fill faces to design for stability in pillar recovery operations. Other backfill technological developments currently receiving widespread attention are high density placement and the use of alternative additives to Portland cement. In Canada, U.S.A. and South Africa attention is also being placed on employing backfill to alleviate rockburst hazards(1,2.3l. In situ testing offers the potential to measure the geomechanical properties of backfill once placed in stopes , in order to assess its actual role in pillar recovery and ground support. Similarly, it offers the ability to provide some quality control during backfill placement. This role is seen as becoming increasingly important with the growing recognition of the need to pay greater attention to the mode of placement, which governs segregation and variation in the properties actually achieved by the backfill after placement."

Jan 1, 1987

By K. H. McDaniel, L. Griswold

The Waste Isolation Pilot Plant (WIPP) is adding a third fan to operate in parallel with, and supplement, its two existing main fans. An engineering analysis conducted in 1995 identified the need for improved system availability and efficiency. The WIPP, located near Carlsbad, New Mexico, is a U.S. Department of Energy (DOE) Carlsbad Area Office facility designed to permanently dispose of U.S. defense-generated transuranic waste in a deep bedded salt deposit. Engineers at the WIPP performed a feasibility analysis for either modifying, supplementing, or replacing its two main mine fans. Since the centrifugal fans were installed in 1988, multiple operational and performance concerns have been identified. A comprehensive engineering study was conducted (McDaniel, et al., 1997) to: identify and quantify operational concerns, evaluate possible alternatives, and recommend an optimum solution. The study indicated that adding a third single-duty centrifugal fan similar to the two existing fans, and equipping that fan with Inlet Van Controls (IVCs) was the best choice. This alternative provided the most desirable combination of operational readiness, and improving system performance. The fan installation project accommodates several operational and scheduling constraints. WIPP is scheduled to receive waste in May 1998. This milestone is proceeded by an operational readiness review. Fan installation could not be allowed to compromise the WIPP's ability to declare facility readiness and had to minimize operational disruptions during the system tie-in. All engineering for the project is completed and physical modifications started in July 1997. The project was completed in 1998.

Jan 1, 1999

Significant advances have been made in the design of centrifugal slurry pumps that are used for pumping high-density viscous and paste slurries. This paper presents the results of a series of centrifugal pump performance tests that were conducted using an FLSmidth 6 x 4 Krebs millMAX centrifugal pump. The pump was fitted with a dry mechanical seal to prevent dilution of the slurry from gland service water, as the theology of the slurry is sensitive to small changes in slurry density. Tests were done using paste kaolin slurry with Bingham yield stress values between 578-1 120 Pa and plastic viscosities between 728 and 1491 mPa.s. The viscous properties of the paste during each pump test were measured using a rotational viscometer. Pump head and efficiency de-rating were measured and compared to the correlations of Walker and Goulas (1984). The test data shows the pump's best-efficiency point (BEP) changes and shifts to the left of the performance curve. The pump efficiency decreases as the slurry yield stress increases. The head de-rating data shows more head de-rating at the low flow rates compared to the high flow rates for the high viscosity slurry, which is in line with the findings of Walker and Goulas (1984). This paper demonstrates that it is possible to pump very viscous, high yield stress slurries with limited head and efficiency de-rating using centrifugal pumps, provided that positive suction conditions are maintained at all times.

Jan 1, 2012

By Jason Clarke, André R. Laplante

"The gravity-recoverable gold (GRG) ore characterization test was developed 15 years ago and has been applied to hundreds of ore samples. The test accurately determines the size distribution of GRG, at which grind it is recoverable, and the extent of its liberation above 150 µm. This contribution shows how the test can be simplified, what are the likely problems to occur, and what information is then lost. Two simplified versions of the test are presented, of which the simplest, grinding a 20-kg sample to a P80 of 75 µm, is retained as the best one. A database of 18 comparative tests is presented. The choice of the full GRG test vs. the simple test is discussed, as is the deportment of the GRG recovered in the standard test but not in the simplest test.INTRODUCTIONThe GRG test was developed in 1990 to characterize the progressive liberation of gold in representative samples of ores, with the primary objective of generating data for a gold gravity recovery model (Woodcock and Laplante, 1993; Laplante et al., 2000). Characterization includes the size distribution of GRG as well as the grind size at which it becomes recoverable. This is achieved in a 3-stage protocol of liberation and recovery using a laboratory centrifuge unit, a Laboratory Knelson Concentrator 3 inches in diameter (KC MD3). This protocol is shown in Figure 1. The first stage takes place at a F100 of 850 ?m (F80 of ~550 ?m), the second at F80 of 180 ?m, and the third at a P80 of 75 ?m. The rationale for the three cycles is the desire to preserve the original size distribution of the gold grains in the ore and to obtain a recovery grind size curve. The feed is a representative sample of ore that can be extracted from ore samples (e.g. drill core reject) or stream products of the grinding circuit other than circulating loads or product having undergone hydraulic classification (e.g. rod mill discharge or SAG screen undersize). Ideally the samples should weigh between 60 and 100 kg, depending on feed grade and gold top size. It is beyond the scope of this paper to fully discuss measures of representativity in the ore sample, for example Gy’s minimum sample mass model (Gy, 1979). However, further work in this regard may be an opportunity. The large initial weight facilitates representativity and minimizes weight and sulphide recovery to the concentrate (since concentrate weight is relatively constant at ~100 g), which limits the recovery of gold in nonsulphide gangue or gold carriers (i.e. sulphides). Thus, the 100 g concentrate carries principally discrete gold species, such as electrum, and native gold. The concentrate and a 600-g representative sample of gangue of each stage are screened down to 20 ?m and each size class is fire assayed (the concentrates to extinction, the tails up to 30 g per size class). The five coarsest size fractions of stage-1 concentrate are individually upgraded using a hydrosizer and the concentrates examined with an optical microscope to assess the degree of liberation of the gold phase. Scanning electron microscope work has established that the GRG has an excellent degree of liberation below 150 ?m in stage 1 and generally a good degree of liberation in stages 2 and 3 (Guerney et al., 2003); as a result the size distribution of the GRG has been found to approach closely that of gold grains (Nesset et al. 2005)."

Jan 1, 2006

By J. Greg Sanchez

The New South Ferry Terminal in the New York City Transit system represents an important milestone for the city. This is the first station designed and built in the 21st century. The design of the fire safety system included relying on Computational Fluid Dynamics to analyze the dispersion of heat and smoke, and modelling of people egress to determine the egress requirements. The project also looked into how to protect the structure from the heat exposure in order to meet the fire rating requirements. This paper provides an overview of the fire safety design approach taken to design the new South Ferry Terminal station in lower Manhattan and looks into fire modelling, structural fire protection, and station evacuation.

Jan 1, 2008

By E. D. Calvert

The Bureau of Mines, in its effort to promote greater utilization of domestically abundant materials, conducted reasearch on an alternate mold material that has commercial potential for titanium investment casting. Using variations of the conventional lost wax molding process, investment shell molds were formed entirely of fused, calcia-stabilized Zr02 and a Zr02-forming binder. Optimization of binder/slurry properties', stucco grain size and dis¬tribution, and curing practices resulted in a structurally sound investment shell that was distortion free and thermally stable. Small titanium castings, weighing up to 10 pounds, were prepared in unheated molds by both static and centrifugal casting techniques. Microstruc¬tural examination of the castings revealed that mold fill and surface quality were enhanced by centrifugal casting, although good results also were obtained from the statically poured molds. Microstructural and electron microprobe examinations showed that excessive, brittle case formation could be avoided by curing the dried shell molds in air for at least 2 hours at 1,400° C. Increasing curing temperature and time above these levels yielded added bene¬fits. Molds fired in vacuum at 1,500° C for 4 hours yielded castings essen¬tially free of case formation. The tensile properties of as-cast test specimens (no surface conditioning performed) id the chemical composition of representative metal samples showed that castings produced were comparable to Grades C-1 and C-2 unalloyed titanium This indicated that no sifnificant degradation of metal properties resulted from mold/metal interaction.

Jan 1, 1981

By R. Karl Zipf, Francois E. Heuze

Stress analysis programs such as MULSIM/NL, LAMODEL, MinSim 2000, and EXAMINETAB are used in the mining industry to analyze stresses and displacements in coal mines, platinum mines, gold reefs, and tabular-type deposits. These relatively simple numerical models can efficiently simulate yielding and failure of a rock mass near a mine opening and subsequent stress transfer. The main input parameters for these models are a family of nonlinear stress-strain curves for the in-seam material. For many applications of these models, such as in coal mining, extensive field measurements and observations exist from which to estimate these stress-strain curves and calibrate the numerical models; however, such measurements are lacking for other types of mines. A three-step method is presented to determine nonlinear stress-strain curves for boundary-element (BE) programs used in many mining applications. The method requires a suite of laboratory-scale strength tests at various confining pressures. Note that this analysis uses laboratory-measured strength and modulus properties of alluvium. The dependency of the mechanical properties of alluvium on scale has not been established, although more tests are being planned. However, it is believed that the relative comparisons performed are valuable regardless of scale effects. First, the FLAC2D computer program is used to model the laboratory tests and determine cohesion (c) and friction angle () for a Mohr-Coulomb material model. Second, another FLAC2D model uses the c and values to calculate vertical stress and strain around a single opening in the rock mass. This model calculates the stress-strain path of points at various distances from the opening boundary. Finally, based on these stress-strain paths, the stress-strain curves needed for a BE analysis are derived. This three-step method was demonstrated in a large, flat-lying underground test facility in very weak rock. The BE analyses agreed well with observations of failure at the test facility and provided a basis for evaluating the behavior of alternative layouts.

To improve the air quality in large-opening stone mines by developing better ventilation techniques, including appropriate fan selection in conjunction with air-coursing methods. Background Stone mines are the most common underground large-entry mines in the United States. Data from the Mine Safety and Health Administration (MSHA) for the year 2000 indicate that there were 162 active nonmetal underground mines in the United States, of which 117 were stone mines. Many underground stone mines are drift mines developed from previous quarry operations. Typically, these room-and-pillar mines have entries that are 20 ft or higher and at least 40 ft wide. These large dimensions lead to a very small ventilating pressure loss, even when significant air quantities move through the mine. This is especially true of drift mine operations where ventilating pressure losses of <0.25 in w.g. are common. Underground stone mines with shafts that are<200 ft deep typically have ventilating pressure losses that are <2 in w.g. The pressure losses through these mines are much lower than those of a typical coal mine or deep metal/nonmetal mine. Therefore, the ventilation techniques and principles are quite different. In addition, because of new MSHA regulations that limit the concentration of diesel particulate matter, these mines may need to greatly increase their ventilation airflow. Therefore, large-opening mines need a fan that can move large air quantities and operate at low static pressures. There are three fan types for mine ventilation: centrifugal, axial vane, and propeller. Centrifugal fans are uncommon in underground stone mines as they are often associated with mines requiring the highest of ventilation pressures. Axial vane fans are widely used in all types of mining operations. They are the most common fan type currently found in underground large-opening stone mines. However, they typically do not operate at low static pressures with high efficiency. Propeller fans are currently uncommon in underground stone mines. They are designed for low static pressures and large air quantities at higher efficiency. This fan type best suits the ventilation needs in large-opening stone mines?they produce large air quantities at low pressure losses. Mines with air shafts<100 ft long and at least 12 ft in diameter have fairly low mine static pressures and may also benefit from propeller fans.

Dec 1, 2002

By D. P. Nicholson

The current phase of office development at Canary Wharf in the London Docklands includes twelve multi-storey buildings varying from eighteen to forty stories in height. The area of Canary Wharf South comprises five multi-storey buildings with low level in fill podium and garden areas. Three of these multi-storey buildings have "pile-cap" designs where the entire building load is applied to the piles. The remaining two buildings have "piled-raft" designs where allowance is made in the design for part of the building load to be transferred to the raft formation. Using a piled-raft design approach has enabled savings to be made on the number of piles used below the raft. This paper describes the calibration analysis undertaken to validate the design method. The ground conditions at the Canary Wharf site are typically fill and recent gravel deposits over the overconsolidated clay and sand of the Lambeth Group. Below these strata is the Thanet Sand. The Lambeth Group provided the founding layer for the raft and contributed to the pile shaft resistance. The Thanet Sand stratum provided the bearing layer for the 1.5m diameter base grouted bored piles. The piled-raft design required an assessment of the building load transfer through the raft to the formation layer. This load transfer led to significant increases in effective stress in the soil below the raft and thence a corresponding increased the capacity of the piles. This interaction of the raft with the prepared formation contributed to between 27% and 45% increase in total vertical load carrying capacity of the piled-raft substructure compared with the pile-cap design method. The development of the piled-raft design was carried out in three main phases: ? Development of the approach and validation analyses. ? Design work on various schemes resulting in detailed design packages. ? Validation analyses using full 3D finite element analysis (presented herein). The validation of the piled-raft design approach was initially carried out against published case histories for piled-raft interaction. To improve on the validation work a full 3D finite element analysis of a simplified pile raft and superstructure (which contributes stiffness to the raft) was undertaken; the analysis included only a quarter of the structure due to assumed symmetry of the structure and vertical loading. This 3D validation analysis is presented herein. The analysis was carried out using the Oasys LS-DYNA finite element program. Prior to carrying out the analysis of the piled-raft an initial finite element analysis was carried out to back analyse a fully instrumented field pile test providing accurate modelling of a single pile performance. This back analysis allowed confidence in the soil parameters used in the 3D model; comparisons of shaft and base resistances between the pile test and the FE model calculations for the single pile are presented. The parameters provided in this work were then carried into the full 3D model of the piled-raft. The 3D model of the piled-raft structure included 18 piles (12 full piles and 6 half piles on an axis of symmetry of the model).

Jan 1, 2002

ALTHOUGH it has been a matter of about one hundred years since the idea of the internal-combustion engine entered the mind of the inventor, the practical application of its use was not attained till 1860, when Lenoir produced an engine similar to the ordinary highpressure steam engine, with the valves arranged to admit the explosive mixture and the discharge of the exhaust gases. In this case no attempt was made to compress the gas before ignition, as it was then considered that the explosion under these conditions had a detrimental effect, inasmuch as it would act as a sudden blow to the working parts. Indeed, he went so far as to inject steam and water sprays to reduce the explosion.Under these conditions the consumption of gas was exceedingly high-about 106 cub. ft. of coal gas per b.h.p. per hour but the mechanical effect showed that the engine ran in every respect as smoothly and quietly as in best steam-engine practice.The extravagant consumption of this engine was clearly pointed out at the time by Gustav Schmidt in a paper before the German Society of Engineers, wherein he states :-&quot; The results would be far more favourable if compression pumps, worked from the engine, compressed the cold air and cold gas to three atmospheres before entrance into the cylinder. By this means a greater expansion and transformation of heat is possible.&quot;

Jan 1, 1912

By M. M. Ayoub

With a return to coal as a major energy source for many companies, more emphasis is being placed on recovery of coal from areas that were formally considered uneconomical to mine. Increasing emphasis is being placed on production from low coal (seam height 48 inches or less) as high coal seams are depleated. Mining in restrictive spaces requires unusual work postures that can turn easy jobs into demanding ones. The objectives of this research were: (1) to evaluate the job demands associated with low coal mining, (2) to survey the anthropometry, strength, and aerobic capacity of low coal miners to determine if they differ from the U. S. population, and (3) to recommend, on the basis of available information, optimal job and work station design for low coal mining. This research effort was supported by the U. S. Bureau of Mines. The male and female anthropometry with the exception of weight and circumferential dimension, was quite similar to the comparison population. Back strength for male and female miners was significantly lower than the industrial worker population. This can be one of the contributing factors of low back problems in mining. Shoveling, timbering, and helpers tasks were physiologically demanding activities. However, due to the frequent stoppage of work, adequate rest was usually available. If work stoppage is corrected, then better work/rest schedules are essential.

Jan 1, 1981

Industrial minerals and rocks are those which are economically important because of desirable physical and/or chemical properties rather than metal or energy content. The evaluation of these resources for investment purposes in general follows established procedures after due consideration of well documented input data. However, in view of the sensitivity of many industrial mineral projects to specific inputs they require very careful analysis. The characteristics of the industrial minerals and the industrial minerals industry are reviewed and the significance of logistics, customer requirements, technology and marketing are discussed. Implications in relation to resources/reserves terminology are considered with phosphate rock used as an example. It is concluded that industrial mineral projects as a consequence of technology and market dependence in particular can give a high level of investment risk. The industry, however, offers most interesting and challenging employment opportunities for geologists, mineral engineers and economists.

Jan 1, 1988

By Jason Rrno

The emergence of Impact and Benefit Agreements (IBAs) in the Canadian mining sector has been read by many as a positive governance innovation. Negotiated directly between mineral resource developers and Aboriginal communities with limited government interference, IBAs serve to manage impacts associated with a mining project and deliver tangible benefits to local communities. Notwithstanding their increasing use and significance, limited systematic analysis has been undertaken to determine whether they are, in fact, working. This paper reports on the effectiveness of a number of IBAs negotiated in support of three northern Canadian diamond mines, drawing on evidence from time-series data, key informant interviews, and focus group meetings in Yellowknife and Dettah, NWT, and Kugluktuk, NU. While some deficiencies were apparent and perceptions of effectiveness varied somewhat by Aboriginal community, the IBAs were generally found to be meeting their objectives, especially with respect to the delivery of benefits. For Aboriginal communities affected by mineral development in the Canadian North, this represents a significant change to typical outcomes of the past. Moving forward, research on IBA effectiveness needs to adopt a longer timeframe and begin to gauge the degree to which IBAs are able to address long-standing concerns associated with hinterland resource extraction beyond their agreement-specific objectives.

May 1, 2010

By N. O. Taylor

THE failure, by swelling, of several cast aluminum-zinc, spiral, pump rods, used to circulate water in a constant-temperature bath, brought up the question as to whether the presence of tin in varying quantities would have any appreciable influence in controlling this action. Previous workers had found the same difficulty with aluminum-zinc alloys, due to their swelling in water or solutions of electrolyte^.^ It was known that pure aluminum was practically insoluble in concentrated sulfuric and nitric acids, presumably due to the formation of an oxidized film on the surface. Concentrated sulfuric acid had little or no effect on pure zinc and tin and concentrated hydrochloric acid would attack all three metals. These facts aroused curiosity as to the probable reaction of the ternary alloys of these metals, and tests were made to determine their resistivity to the action of common laboratory reagents. Samples, covering the entire range of the ternary series of aluminum, zinc and tin alloys, were made up from good grades of the commercial metals.2 The materials were melted, at as low temperatures as possible, in graphite crucibles in a gas-fired crucible furnace. Graphite crucibles were used in preference to clay, to prevent the absorption of silicon by the aluminum, as found by previous workers. The melted materials were stirred thoroughly with pine sticks in order to ensure complete mixing and the greatest possible freedom from oxidation, and were cast in sectional, iron molds giving bars % in. in diameter and 5 in. long.

Jan 1, 1927

By James P. Stewart

This case history describes the engineering design and construction for the Contractor of a 35-ft-deep excavation for an 800-square-foot addition to an existing sewage pump station. The site posed unexpected geotechnical complications that included deep gravelly soil, a history of local construction difficulties, groundwater consisting of heavy salt brine, and the need to underpin the existing pump station. The project took an interesting twist when the Owner issued a change order limiting the dewatering discharge to a fraction of that required to lower the water table. This documents the interesting circumstances of this job and documents the unusual subsurface conditions in the Syracuse, NY Lakefront area.

Jan 1, 2003

By Lyon R. J P

The quartz-cassiterite-wolfram veins at the Aberfoyle Tin Mine, north-eastern Tasmania, form a sheeted zone about 200 ft. wide and 1,600 ft. long in slightly contact metamorphosed shales, slates and greywackes, and are associated with a cupola of aplitic granite whose top is about 1,050 ft. below the present surface. Economic mineralization persists from the surface down to a vertical depth of 1,050 ft. to 1,100 ft., dying away in the vicinity of the cupola. Down to the 9-level there is a progressive increase in wolfram content of the veins, and a decline in cassiterite content, with increasing depth.The veins are banded or zoned, with a seivedge of muscovite on the wall. Cassiterite, wolfram and sphalerite occur inside the selvedges, projecting into a core of quartz of varying width. Other sulphides form the central part of some narrow veins, or occur as clots in the quartz. The general sequence of deposition of the ore minerals was: (1) cassiterite, wolfram; (2) arsenopyrite, pyrite, molybdenite; (3) pyrrhotite (in part); (4) blende-group minerals-chalcopyrite, sphalerite, stannite, pyrrhotite (in part)-as solid solutions; (5) galena, tetrahedrite, matildite, native bismuth, scheelite; (6) marcasite and secondary pyrite, magnetite and hematite. The sequence of deposition of the gangue minerals was: (1) fluorine-bearing minerals-muscovite topaz, apatite, triplite, fluorite-more or less contemporaneous with the cassiterite and wolfram;&apos; (2) quartz-contemporaneous with the earlier sulphides; (3) carbonates--contemporaneous with the later sulphides. The stages overlapped somewhat.The composition of the sphalerite and heat treatment experiments with the solid solutions indicate that the blende-group sulphides were deposited at about 6000 C., and cooled rapidly, so that unmixing of the solid solutions was arrested. This accords with the likelihood that the country rock temperature was not above 2000 C. Annealing experiments at between 3500 C. and 6000 C. led to further precipitation from solid solution at the lower temperatures, and to significant segregation by solid diffusion within, a week, indicating that both deposition and cooling of the ore were rapid processes-completed in a matter of days. Since the mineralizing solutions must have lost some heat during...

Jan 1, 1957