Search Documents

By E. H. Jr. Dix

THE use of magnesium as an alloying element in aluminum alloys has been limited, in general, to comparatively small quantities. In duralumin-type, strong-aluminum alloys, magnesium is present to the extent of ½ to ¾ per cent. and various grades of Magnalite and the "Y" alloy of the National Physical Laboratory of England contain up to 1 1/2 per cent. In this country small quantities of aluminum alloy sheet containing 4 per cent. magnesium are produced commercially. All commercial aluminum contains sufficient silicon to convert a portion of the magnesium added to the compound Mg2Si. It is well known that the solubility of both magnesium and magnesium-silicide decrease with decrease in temperature. It is, therefore, impossible to separate the age-hardening effect of the magnesium-silicide from that of magnesium, except by the use of aluminum of such high purity that the silicon content is negligible. The present paper is the fifth1, 2,3,4 of a series from the laboratories of the Aluminum Co. of America reporting the results of investigations of the equilibrium relations in aluminum-rich alloys made from the high purity aluminum manufactured by this company .5

Jan 1, 1929

Shaft sinking through an amphibolite-granite rock mass experienced rock bursts on the shaft walls and benches. However, rock burst phenomena was exhibited only in granite, which is e1asto-brittle with ability to store strain energy caused by orogenic and man made stresses. To improve ground conditions, blasting of destressing holes at shaft corners was carried out. By this technique rock burst during shaft sinking was minimized, but not eliminated.

Jan 1, 1982

By Andrew L. Peterson

CATOH Inc. of Weedsport, New York recently completed a very challenging Bored-In Pile project which features unique construction techniques in the installation and load testing of 45 and 100 ton capacity piles. The bored-in piles were installed on a twenty-nine million dollar New York State Department of Transportation project which began in the fall of 1995 and ended in March of 1997. The project included the construction of 5 new bridges to alleviate a very congested traffic network which had come to be known as the "Octopus" in the small city of Ithaca, New York. CATOH Inc. was awarded the piling contract by general contractor Santaro Industries in the fall of 1995. Piling installation work was completed in March of 1997. BACKGROUND The project is located at the southern tip of Cayuga Lake which lies in the heart of Upstate New York's Finger Lakes Region. This region is popular not only for wine making and vacationing, but also for its impressive geological history. The glacial activities that helped to form the deep valleys of this scenic area are also responsible for creating challenging underground conditions for deep foundations work. CATOH developed two pile designs to accommodate differing site conditions on the project. Internally reinforced piles were developed for use in the center of the valley and externally reinforced piles were developed for locations close to the valley wall.

Jan 1, 1997

By Joseph T. Coe, Siavash Mahvelati, Alireza Kordjazi

This paper introduces recent advances in stress-wave NDT systems for use in assessments of in-service foundation integrity and drilled shaft construction. The primary results of the laboratory experiments are very promising, as the acquired image was capable of differentiating changes in pile cross section as low as 0.3 cm. The preliminary results with the same hardware components on a relatively large scale cemented sand model were also promising. A brief overview is provided of both systems including hardware, survey methods, and data processing techniques, followed by a discussion on application of the results to QA/QC of deep foundations. INTRODUCTION There are two main applications in which current QA/QC NDT technology fails to provide sufficient information regarding deep foundation conditions: (1) detection of flaws in outside cover concrete of drilled shafts and corrosion in steel piling; and (2) evaluation of anomalies beneath the bottom of drilled shaft excavations. Previous studies have demonstrated the capabilities of high frequency stress waves for geotechnical and foundation evaluation purposes (Lee and Santamarina 2005; Coe and Brandenberg 2010; Coe and Brandenberg 2012; Coe and Kermani 2016). Higher frequency waves can visualize smaller anomalous features at the expense of higher attenuation and smaller propagation distance. Therefore, the goal of this study was to advance the state of NDT practice by development of a prototype high resolution stress-wave imaging system as proof-of-concept. The equipment and hardware were modular, which allowed simultaneous development of two system configurations for application to in- service foundations as well as drilled shaft excavations during construction. Results are presented based on two large scale soil models. The first laboratory model simulated section loss in an in-service steel pipe pile and drilled shaft foundation (Fig. 1a). The second model simulated anomalous conditions beneath drilled shafts excavations as might be encountered in areas with significant karst (Fig. 1b). For both models, evaluation of foundation conditions relied on the propagation of small amplitude seismic stress waves using hardware similar to those described in Coe and Brandenberg (2010) and Coe and Brandenberg (2012).

Jan 1, 2018

By F T. Suorineni, L Baird, A Papaioanou, D Hines

The Mathews et al (1981) stability graph was developed to provide guidance in the determination of stope sizes to control dilution in bulk mining of large orebodies. Longhole and sublevel open stoping (LHOS and SLOS) are the lower end in scale of underground mass mining with panel and block caving (PBC) at the higher end. Currently, the stability states of stopes in the stability graph are described qualitatively as stable, unstable or cave. The alternative quantitative option to the qualitative stability graph is the Equivalent Linear Overbreak Slough (ELOS) stability graph. The ELOS stability graph only applies to narrow vein orebodies. It is easy for the Mathews et al (1981) and the ELOS stability graphs to be applied outside the limits of their databases. What is currently referred to as ‘stable’ in the present stability graphs has diverse interpretations at different mines depending on their acceptable dilution values. In 2014, a research program was conceptually conceived at the UNSW Australia School of Mining Engineering to develop a quantitative dilution-based stability graph independent of orebody width to address some industry concerns on the use of the stability graphs. A dilution-based stability graph provides the mining engineer the flexibility to determine open stope sizes based on what dilution amounts are acceptable. The graph also unifies both the Mathews et al (1981) and ELOS stability graphs for wide and narrow vein orebodies, thus, eliminating their potential misapplications. To date, the concept is proven with case studies from metalliferous underground mining operations located across Australia. This paper presents the dilution-based stability graph concept, the initial results and future plans to account for other critical factors and increase confidence in its application with the addition of more data outside Australia.CITATION:Suorineni, F T, Papaioanou, A, Baird, L and Hines, D, 2016. A dilution-based stability graph for open stope design, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 511–522 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By W. Chi, R. Regan, R. A. Washington

"In uranium mines, the purification of underground mine air can be accomplished by the removal of dust particles and radon daughters using filters. Full-scale statistically designed experiments with flow rates up to 10,000 cfm have been conducted at Denison Mines Ltd. on mine air filtration with vermiculite as a filter material. Various filtration bed thicknesses were chosen, with different face velocities through each bed thickness. Results on total dust, respirable dust and radon daughter collection efficiencies were analysed statistically. It is shown that these collection efficiencies are directly related to the filter bed thickness. However, the different face velocities seem to affect only the collection of radon daughters. Optimum collection efficiencies for a clean bed of about 30% were found for respirable dust and radon daughters, and about 41>% for total dust, using an 8-in.-thick bed and a face velocity of 500 fpm. Dust build-up on the filter bed during operation led to an increase in collection efficiency, reaching 40 to 60% after two weeks."

Jan 1, 1973

By Joseph Ribak

Grunerite asbestos (amosite) has been shown in epidemiological and experimental animal studies to cause lung cancer, mesothelioma and pulmonary fibrosis commonly referred to as asbestosis. An overview of the human and experimental animal studies describing the health hazards of grunerite asbestos (amosite) is presented. Of the many human studies describing the health hazards of asbestos, only three factories using mainly, if not exclusively, grunerite asbestos (amosite) have been studied. The first is a series of reports on a cohort of 820 workers from a plant located in Paterson, NJ. Among this cohort, 18.7% died of lung cancer and 17 mesotheliomas occurred. The Paterson factory closed in 1954 and moved to Tyler, Texas where it operated until 1972. Among the 1130 former workers in the Tyler plant 6 mesotheliomas were reported with 15.8% lung cancer mortality. The third grunerite asbestos (amosite) exposed cohort was an insulation board manufacturing facility in Uxbridge, United Kingdom. Here 17.1% of the workers died of lung cancer and 5 mesotheliomas occurred. The lung content from 48 Uxbridge workers was analyzed by analytical transmission electron microscopy for mineral fibers. The relationship between grunerite asbestos (amosite) concentrations in the lung correlated with grades of fibrosis and asbestos bodies and was lower than the concentration found in the cases with malignant tumors. The lung cancer cases contained more grunerite asbestos (amosite) than mesothelioma cases, and in the cases of non-alignant disease the concentrations were still lower. In both types of malignancies the concentration of grunerite asbestos (amosite) was very high-over a billion fibers per gram of dried lung tissue. Occupational exposure to airborne concentrations of between 14 and 100 fibers of grunerite asbestos (amosite) per milliliter after 20 year latency causes marked increases in lung cancer, mesothelioma and pulmonary fibrosis (asbestosis). © 2007 Elsevier Inc. All rights reserved. Keywords: Grunerite asbestos; Amosite; Mesothelioma; Asbestosis

Jan 1, 2007

The nature of the specialty glass and ceramic business magnifies the dependency of the ultimate product on the unique properties of their raw materials used to make them. This dependency has implications in the management of risk in the supply process which requires a special procurement organization and program commitment to be successful. The Coming system of managing critical materials and factors in development of alternate new suppliers and products is discussed.

Jan 1, 1989

By E. J. Gleim

A list of permissible mine equipment, tested and approved by the Bureau of Mines previous to January 1, 1942, was published in Bureau of Mines Information Circular 7207.3/ The list of that date was complete as to equipment then available and in current use. Information Circular 7240,4/ published as a supplement thereto, listed equipment approved curing the calendar year 1943. The present list is another supplement covering approvals issued during the calendar year 1943. The items are numbered to indicate the consecutive order in which each type of machine or device was approved in its particular classification. Thus, Information Circular 7207 gave 19 drills and drilling machines on the Bureau's active list. No additional approvals were given in 1942, but the three issued in 1943 bring the total to 22. Item 102, under Loading Machines and Conveyors, also appeared in Information Circular 7207, and items 120 and 124 appeared in Information Circular 7240. These numbers are repeated here to show that approvals were granted during 1943 for additional voltages on machines previously listed for one voltage only. Equipment listed in these circulars is approved by the Bureau of Mines only when found upon inspection and test to comply with minimum standards of safety as outlined in schedules prepared on the basis of many years of experience in dealing with safety problems of the coal-mining industry. The use of such equipment in mines known to be gassy, as well as in those that may become so, is earnestly recommended in the interests of safety. This circular is published so that the industry may be kept

Jan 1, 1944

By Brian Zelenko, William H. Hansmire

"By the time the latest expansion of the Washington Metropolitan Area Transit Authority (WMATA) system, known locally as Metro and which opened in 1976, is completed in 2020, the system will serve 97 stations and operate on 188 km (117 miles) of track on six interconnecting lines. Metro provides a critical transportation link to a population of approximately six million people within a 3,900-km2 (1,500-sq-mile) Washington Metropolitan area and has allowed job growth to expand to all corners of the region. In the 1950s and 1960s, when the system was first conceived and construction began, most jobs were centered in downtown Washington, and most of the workforce commuted by bus or car. Today, transit-oriented development has increased residential, commercial and government facilities near most of the existing 91 stations increasing the importance of the Metro system as a critical transportation link for the region. According to recent American Public Transportation Association (APTA) data, Metro is the second busiest transit system in the United States (after New York City’s transit system).During the nearly 50 years of construction on the Washington Metro system, technology improvements and lessons learned from the global tunneling industry were implemented. Portions of this background and history have been adapted from other work by the authors Roach et al. (2017) and expanded for use herein. For soil tunnels, these improvements included the change from a “two-pass” tunnel lining with a typical initial lining of steel ribs with wood lagging or segmental precast lining erected within the tunnel shield followed by a final lining of cast-in-place concrete to a one-pass lining system of pre-cast concrete gasketed segmental lining. Soil tunnels were originally excavated using open-face tunnel shields, but changed over time. By the late 1980s, tunneling using closed, pressurizedface tunnel boring machines (TBMs) using a one-pass tunnel lining consisting of segmental precast concrete permitted tunneling in a wider range of soil conditions with much less risk of damaging overlying utilities or structures, greater safety for tunnel construction personnel and without the need to dewater the soils. However, due to concerns about conditioning clays with earth pressure balance (EPB) TBMs, open face machines were still favored by contractors for their better advance rates, lower cost and ability to deal with boulders that were occasionally encountered in the Coastal Plain Terrace Deposits."

Jan 6, 2018

By Nilabjendu Ghosh, Satyendra Kumar Singh, Gautam Banerjee, Harshit Agrawal

High-production methods like longwall mining with hydraulic powered supports are necessary to increase underground coal production in India. Longwall mining had a mixed success record for Indian geo-mining conditions. In this paper, an analysis is presented to optimally design an array of chain pillars in multi-seam longwall mining panels in the deepest coal mine in India. The study found that a chain pillar of 80-m width and 195-m length is necessary for long-term stability without any reinforcement. It was also observed that an optimum chain pillar can be designed by providing suitable side reinforcement (side bolting) which will reduce the chain pillar dimensions to 55-m width and 160-m length. Optimum design of chain pillars will reduce the coal locked up in these chain pillars by ~ 77%. This will also reduce the gestation period of longwall mining panel development. This paper also evaluates the maximum tensile subsidence strain induced at the surface and finds that the values are within the safe working limit of 3 mm/m. Thus, this paper finds direct application in the design of future multi-seam retreating longwall mining panels in Indian geo-mining conditions.

By Nilabjendu Ghosh, Satyendra Kumar Singh, Gautam Banerjee, Harshit Agrawal

High-production methods like longwall mining with hydraulic powered supports are necessary to increase underground coal production in India. Longwall mining had a mixed success record for Indian geo-mining conditions. In this paper, an analysis is presented to optimally design an array of chain pillars in multi-seam longwall mining panels in the deepest coal mine in India. The study found that a chain pillar of 80-m width and 195-m length is necessary for long-term stability without any reinforcement. It was also observed that an optimum chain pillar can be designed by providing suitable side reinforcement (side bolting) which will reduce the chain pillar dimensions to 55-m width and 160-m length. Optimum design of chain pillars will reduce the coal locked up in these chain pillars by ~ 77%. This will also reduce the gestation period of longwall mining panel development. This paper also evaluates the maximum tensile subsidence strain induced at the surface and finds that the values are within the safe working limit of 3 mm/m. Thus, this paper finds direct application in the design of future multi-seam retreating longwall mining panels in Indian geo-mining conditions.

By Carl R. Peterson

[In lTI n,v und I'gr'oun nllnin~ Opt'I'ali n' the high . t cost is the loading and I 3ulage of t tln-of -D"'line ot'. 01' hauling costs can be r duced signifi-cant\v with the us ~ (r \) >It corn'e)'OI' " a COnlTllOn pl'acti c i.n coal and other s 0 t'L rn I n r' a l III i, n e , '. Jf 0 vel s i z ' () f' e can bee 1 i 11.11 tl ate I rH'i 0 I' lO C n v e . in g, ]

Jan 1, 1976

By Xuchen Fan, Chenyang Zhou, Yuemin Zhao, Liang Dong, Chenlong Duan

A gas–solid fluidized bed using magnetite particles is an effective methodology for coal beneficiation in the field of dry coal cleaning. Broadening the size range of magnetite used in the bed decreases medium preparation cost. In this study, a tapered fluidized bed was used to investigate a magnetite particle size range of −0.5 + 0.074 mm. The results showed that a tapered fluidized bed effectively strengthens mixing of magnetite with a wide size range (−0.5 + 0.074 mm). The results of beneficiation experiments indicated that with increasing tapered angle, separation efficiency increased and then decreased. The highest separation efficiency was obtained at a tapered angle of 10°. The optimal results showed that the ash content of the concentrate decreased from 31.82% to 12.33% with a probable error of 0.11, which indicated that a tapered fluidized bed was efficient to improve fine coal beneficiation performance.

The production of sulphuric acid at Port Pirie by the contact process began in March 1924 with the commissioning of the Electrolytic Zinc Co.'s roasting and acid plant. This plant, operated by B.H.A.S. Pty. Ltd. on behalf of the E.Z. Co., continued to produce sulphuric acid from the gases evolved when roasting Broken Hill zinc concentrate in mechanically rabbled furnaces until September 1954, when the plant was closed down.In this peri9d of approximately 30 years some 600,000 mono tons of 98·5 per cent sulphuric acid was produced, most of which was used for fertilizer production at Wallaroo and Port Adelaide. During World War II 14,400 mono tons of the above was produced in the form of 20 per cent Oleum and railed to the Salisbury Munitions Factory for use in the production of nitro-glycerine, gun-cotton and T.N.T.In the early post-war period various ways of converting at least some of the sulphur in the gases' discharged to atmosphere from the lead sintering plant were considered until, in 1949, it was decided to erect a modern contact acid plant. Much work remained to be done on the roasting plant to produce a gas of suitable grade for the contact process and also on the design of a purification section suitable for the treatment of D.L. gases.The acid section itself, however, was largely of conventional design and it was therefore decided that this would be erected first. To it was then attached a sulphur-burning section to allow it to operate as a "hot gas" brimstone acid plant until the roasting and gas purification plants had been designed and erected. In this way the urgent need for sulphuric acid in the fertilizer industry would be relieved, to some extent at least, as soon as, possible.

Jan 1, 1956

By D. Michael Holloway

The California Department of Transportation (CALTRANS) evaluated several pile foundation schemes for supporting the structures along the realignment of Interstate 880. The project replaces the double-decked (Cypress) viaduct collapsed in Oakland, California during the 1989 Loma Prieta Earthquake. Structural support demands led to the selection of steel pipe piles (16-, 24-, and 42-inch-(406-, 610- and 1067-mm-)diameter), filled with concrete and steel reinforcement. Deep penetrations required through layers of very dense/cemented sands in some locations, caused serious drivability and pile integrity concerns. The need for large pile driving hammers and large diameter steel pipe piles pushed the engineers well beyond local experience. Such questions as the feasibility of driving the pipes closed-ended through dense upper strata and quantifying the effects of installation on the long-term capacities of the piles led Caltrans to develop a comprehensive pile test program to address the design and construction issues effectively. The results were furnished to prospective bidders on the production stages of the ensuing contracts.

Jan 1, 1995

By Y. Sasseville

"Niobec has been using vibrating screens and screw classifiers as a double stage classification in its grinding circuit since the very beginning of its operation in St-Honoré. Most of the other mineral processing plants around the world uses cyclones as the classification device in their grinding circuit. The difference between these two methods are well known in terms of capital cost and grinding efficiency but the differences in terms of the impact on the downstream processing stages are a lot harder to predict and are case specific. In the interest of lowering the capital cost of a future expansion project, Niobec decided to test the cyclones in its actual grinding circuit and evaluate their impact on the recovery of the downstream processing stages as well as the operating cost of the mill. We switched between cyclones and screens for 8 month in 2013 and early 2014 and we are now operating only with cyclones since march 2014.INTRODUCTIONThe Niobec mine and concentrator were built in the mid 70’s and at that time, the mill was processing 1 500 tons per day. Over the years, many expansion projects have brought the plant to 7 000 tons per day. Throughout the initial concentrator design and commissioning, screens have been chosen over cyclones because of their higher classification efficiency which is known to reduce variability and limit the fine generation especially due to a high undersize classification efficiency. Just like many other plants, fine particle generation is a major problem at Niobec because of its negative effect on downstream processing stages. In the interest of lowering the capital cost of a future expansion project, Niobec’s engineering team decided, 35 years later, to test the cyclones in its actual grinding circuit and evaluate their actual impact on the final recovery and the operating cost of the mill.The grinding circuit is separated in two lines which will be called Circuit #1 and Circuit #2 along this paper. Circuit #1 is, as you can see in Figure 1, composed of a rod mill and two parallel ball mills in closed circuit with screens and screw classifiers. The screens oversize are sent to the screw classifiers while the undersize are sent to the next processing stage. The screw classifiers overflow are both sent back to the pump box while their oversize streams return in their corresponding ball mills for further grinding. Circuit #2 is, as you can see in Figure 1, quite the same as Circuit #1 except it has only one set of screw classifier and ball mill. Figure 1 also shows the modification in arrangement each circuits went through to integrate the new cyclones. One of the ball mills in Circuit #1 now appears dotted because it can still be used but is not now"

Jan 1, 2015

By W. T. Abel

The rate of the steam-carbon reaction, which is of fundamental importance to coal gasification, was determined by passing steam over graphite specimens suspended in an electrically heated tube. The measurements were made at 1,900° to 2,400° F. and at steam-feed rates of 0.1 to 2.0 moles of steam per mole of carbon per minute. At the maximum steam-feed rate, the reaction rate of carbon ranged from 0.4 percent per minute at 1,900° F. to 7 percent per minute at 2,400° F. Up to about 2,200° F., the steam-feed rate had only a slight effect; above this temperature, it limited the reaction velocity when the final mole fraction of steam in the reaction products was much less than 1.

Jan 1, 1962

By F. Bélanger, P. A. Fournier

"Modelling and optimization techniques used in the operation of the Detour Lake Mine leach circuit are contrasted to a 1973 review of contemporary techniques used by a major gold producer. The leach circuit at the Detour Lake Mine was modelled using a full factorial Design of Experiment of stirred tank reactor leach tests using circuit feed. Contour plots of extraction were applied in the plant to optimize addition rates of cyanide and the newly-commissioned lead nitrate system. Contour plot sections were used to understand the impact of sulphur in circuit feed at different operating dissolved oxygen concentrations. The 1973 review paper offers insight into industrially-applied modelling and optimization techniques. In particular, a mathematical model of plant data was developed using multilinear stepwise regression analysis. The model was presented using graphical representations available at the time and applied to optimize the rates of cyanide addition. Off-the-shelf software solutions of today allow mineral processors to quickly and easily visualize data, allowing them to re-allocate time and resources spent processing data to generating raw data and extracting actionable information.IntroductionModelling and optimization in mineral processing is the art of reducing reality through judicious use of assumptions to understand a process and leverage this knowledge to engineer practical solutions to metallurgical problems. Data analysis is at the core of this enterprise.While this paper showcases the modelling work done at the Detour Lake Mine (DLM), the primary objective is to pause and reflect on how far the field has progressed since the 1970’s. A snapshot of state-of-the-art gold cyanidation modelling at that time is a review paper of the Anglo American Group’s capabilities (Brittan & van Vuuren, 1973). The objective of this paper is not a play-by-play of the evolution of modelling and optimization since that time. Rather, it is a comparison of the field at two points in time.In 2016, DLM undertook an extensive bench-scale leach circuit modelling program to better understand the impact of cyanide, dissolved oxygen, lead nitrate, grind size, density, and pH on gold cyanidation (Fournier, 2016). Two major capital expenditure projects were anticipated for 2017: improvements to oxygen control and a lead nitrate distribution system. While the lead nitrate system was planned for construction, the design parameters had not yet been selected. Following the development of the model, plant trials were executed to validate aspects of the model and the methodology was expanded to address other plant issues, in particular the effect of talc chlorite and pyrrhotite in leach feed.The variables of the bench-scale study are summarized in Table 1. Dependent variables were varied using a full factorial design of experiment with two repetitions for each test condition, yielding a total of 300 tests. Test order was randomized to eliminate bias from independent variables."

Jan 1, 2018

By Roberto Folchi, Hans Wallin

Lake Mead, the largest man-made reservoir in the United States, is located about 30 miles southeast of Las Vegas, Nevada. For the construction of Lake Mead third water intake, which is entirely placed underground, an underwater excavation was needed at a depth of 100 m (330 ft): a large surface had to be deepened by 20 m (66 ft) in basalt.

Jan 1, 2012