Search Documents

By G. H. Gronhovd

This report describes the design and initial operation of a slagging gasification pilot plant installed by the Bureau of Mines at the Lignite Research Laboratory, Grand Forks, N. Dak., in 1958-59. The tests covered in this report were conducted over a period of about 2 years, beginning in April 1959. The pilot plant was designed for eventual operation at pressures ranging from 400 to 600 p.s.i.g. (pounds per square inch gage); however, for the preliminary test reported here, the gasifier was fitted with a low-pressure slagging section and operated at atmospheric pressure and at 80 p.s.i.g. The reason for using a low-pressure slagging section for initial operation was to facilitate modifications in design during the development of a reliable slagging procedure.

Jan 1, 1962

By Thomas F. Anderson

(Measurements of stable isotopic variations (sulfur, carbon, and oxygen), supplemented by chemical, mineralogical, and petrographic analyses have been used to investigate the processes responsible for : (1) the incorporation of sulfur in coal, and (2) the (development of permineralized peat zones ("coal balls"). Sulfur isotopic results indicate that there are two principal sources of sulfur in the Pennsylvanian coals from the Illinois Basin: (1) "primary" sulfur assimilated by plants (low-sulfur coals), and (2) "secondary" sulfur produced by reactions involving H2S that was produced by the anaerobic reduction of sulfate in seawater which permeated the peat during post-depositional marine transgressions (the dominant source of sulfur in high-sulfur coals). Sulfur isotopic compositions of low-sulfur coals in Several Tertiary basins of Wyoming are consistent with a plant sulfur source. However, the inverse correlation between content and isotopic composition of sulfur observed in coals from the Powder River Basin suggest some "secondary" additions to these low-sulfur coals. Seveeral Quaternary (freshwater pears which were submerged by sea-Level rises during deglaciation over the past 30 ka have sulfur contents and isotopic compositions similar to high-sulfur coals. Carbon and oxygen isotopic compositions of calcareous coal balls from North America and Europe suggest that (1) the carbonate was derived from variable proportions of oxidized plant matter (typically predominant) and inorganic carbonate, and (2) the carbonate minerals were precipitated from fresh-to-brackish waters. Local geochemical and hydrological conditions were apparently more important than regional depositional environments in controlling the source of carbonate and the development of coal balls.

Jan 1, 1983

Local conditions at Hatches Creek are described, together with the mineralogy, mining and treatment of tungsten ores, with particular reference to procedures adopted by Pimer Mines, N.L.The Hatches Creek tungsten field covers an area of about 20 square miles in: Central Australia; 285 miles' N.E. of Alice Springs. Access is by rail to Alice Springs, then by 200 miles of bitumen highway to Barlo Creek and 8,5, miles of bush track to the field. Passengers can also reach the mines by... A semi-desert climate prevails Rain; generally in the form of thunderstorms falls in the summer months: December to March. Average annual rainfall is approximately 15 inches but there is great variation from year to year, occasional droughts being followed by torrential downpours. Vegetation is sparse except in the wide creek beds. Surface water occurs in rock holes some of which, spaced miles apart, carry permanent water...

Jan 1, 1955

By M Scoble

This paper will report on the application of data collected through the performance monitoring of large diameter surface rotary blasthole drii and electric mining shovels, in an integrated approach to blast optimizatiion.

Jan 1, 1992

By R. A. V. Raff

Although falls of roof, face and rib (or side) of coal mines were the third ranking cause of disabling accidents in 1966, the accidents from these falls resulted in the most serious injuries and accounted for approximately 50 percent of the total fatalities (I). Further breakdown of these statistics shows that 88 percent of the fatal accidents occurred within 100 feet of the working face and that 96 percent of the deaths were in bituminous mines, with only four percent taking place in anthracite workings. These figures demonstrated the need for improved reinforcement procedures in operational coal mines, and they provided ample justification for research in the area of accident prevention. The purpose of this project was to investigate the use of polymers and of related techniques to achieve rock bonding and reinforcement of coal mine structures, in order to obtain better or permanent ground support (e.g., drifts, entrees, coal and ore passes, galleries, tunnels and shafts) by the fill ing of fissures in the rock, thereby preventing or delaying the onset of serious rock degradation processes.

Jan 1, 1973

By D. W. Smith, Robert F. Mehl

It has been shown by numerous studies that the orientations of new metal crystals are determined by the orientations of the crystals in the original matrix, whether these new crystals are formed by recrystalliza-tion, by precipitation from solid solutions, or by transitions in the solid state. The orientations of crystals formed by recrystallization of cold-worked metals that bear preferred orientations are occasionally simply related to the initial preferred orientation; often, however, the relationship is not simple, but complicated and obscure in origin.1 The orientations of crystals formed by precipitation from solid solutions have been shown by many studies in this and other countries to be determined by the orientation of the crystals of the solid solution stable at the higher temperatures, though here again complicated cases have been found and no general theory is available.2 Related to this latter class are the relationships found in crystals formed by suppressed transforma-

Jan 1, 1935

By D. W. Smith, Robert F. Mehl

It has been shown by numerous studies that the orientations of new metal crystals are determined by the orientations of the crystals in the original matrix, whether these new crystals are formed by recrystalliza-tion, by precipitation from solid solutions, or by transitions in the solid state. The orientations of crystals formed by recrystallization of cold-worked metals that bear preferred orientations are occasionally simply related to the initial preferred orientation; often, however, the relationship is not simple, but complicated and obscure in origin.1 The orientations of crystals formed by precipitation from solid solutions have been shown by many studies in this and other countries to be determined by the orientation of the crystals of the solid solution stable at the higher temperatures, though here again complicated cases have been found and no general theory is available.2 Related to this latter class are the relationships found in crystals formed by suppressed transforma-

Jan 1, 1935

This report covers the results of an industrial engineering study that assessed the safety and efficiency of underground ore handling in U.S. metal mines. Significant conclusions that will be of benefit to the entire mining industry are the following: It appears from the study that the productivity of the slushing equipment itself cannot be substantially increased using the existing technology; the unsafe situations associated with slushers can be improved by better anchoring practices, by providing better work station layout that incorporates improved clearances and protected walkways over the ore pocket, by lighting the slusher drift, and by improved operator training; improved technology needs to be applied to the movement of broken ore in the stopes; and slushers will continue to be used in the mining industry in certain spedial and unique situations outlined in the report.

Jan 1, 1974

By T. H. Eyde

Estimated natural zeolite production worldwide during 2004 remained at about 3.6 Mt (4 million st), about the same as in 2003. China continues to be the largest producer of natural zeolites followed by Cuba, Germany, Japan and South Korea. This may be changing, however. Since 1988, zeolite production from Australia, Indonesia, Malaysia, New Zealand, Philippines and Thailand has increased rapidly. Most of the production is consumed in aqua culture. Global demand for seafood has exceeded the ability of the oceans to supply it without over fishing. Zeolite minerals remove ammonia compounds from the ponds in which fish and shrimp are grown. It is estimated that, in Thailand and Indonesia more than 55,000 farms produce260 kt (286,500 st) of shrimp. Therefore, as shrimp production increases, so does zeolite consumption.

Jan 1, 2005

By I. Barin

The thermodynamics of cyclone smelting of sulphidic copper ores is described using as example the production of copper matte with 75 wt % Cu. Equilibrium calcualtions and material and energy balances show that an increase in process temperature from 1600 K to 1900 K results in the extensive transfer of minor elements such as As, Sb, Bi, Pb, Zn,.... to the gas phase. A pilot plant for carrying out the cyclone smelting process is described. Calculations of material and heat transfer for the reaction of ZnS show that the smelting reactions of sulphides in the cyclone take place very rapidly at high temperatures. The dissociation of the sulphides with subsequent oxidation reactions in the gas phase plays an important part in. the process and is mainly controlled by heat transfer.

Jan 1, 1983

By William G. Pariseau

Solvay Chemicals Company mines trona in south-central Wyoming and has done so for many years. The mine is one of several in a mid-continent sedimentary basin that hosts the largest trona resource in the world. Trona is an evaporite, a sesquicarbonate that occurs in several seams of varying thicknesses and depths. Trona is processed into soda ash which has a number of industrial uses in the manufacture of glass, detergent, paper and chemicals. Figure 1 shows the location of the Solvay Mine. A ventilation shaft was recently excavated at Solvay Chemical Company’s mine in the trona patch. In fact, a 22 ft (6.7 m) diameter shaft (inside diameter) was bored upwards from the 1500 ft (457 m) level to the surface. The first bored section was 26 ft (7.9 m) in diameter that allowed for a 2 ft (0.6 m) thick concrete liner. This section began at a depth of approximately 1500 ft (457 m). A second bored section was 24 ft, (7.3 m) in diameter that allowed for a 1 ft (0.3 m) thick concrete liner. This section began at a depth of approximately 750 ft (229 m). This shaft is the #5 Shaft. Figure 2 shows the cutter head used to excavate the shaft.

Feb 1, 2025

By G. L. Oldright

The first Report of Investigations of the present series (No. 4562) was on the fundamental properties of lead compounds, and the manner in which they set limits to the richness of lead products treated in the usual sintering-blast furnace units. These properties of the compounds were emphasized, as' it was desired, also, to learn the limitations of smelting the same compounds in present ore hearth practice; the hearth has a competitor in these "usual" units, even with the rich lead feeds best adapted for the hearths. Operating conditions that were followed in older metallurgical processes, when rich products, were treated, were outlined. The second report of the series (R. I. 4563) was on the development of the ore hearths of the types now used in the Tri-State from the viewpoint of the features, functions, and dimensions of the earlier hearths that had been most changed. Experimental data, for both well and poorly desulfurized charges being considered, were given to show the relative changes in the sizes and compositions of the charges after they were added to the ore (Scotch) hearths. A general picture was given of the charge column and of the conditions prevailing there when the operation was satisfactory. In this third paper, the composition of the gases prevailing in the charge column at various elevations will be correlated with what has been learned of the nature of the charge column in order to trace the steps of operation by which lead sulfide is converted into metallic lead. The metallurgical factors that govern operation and the lines along which improvements may be made will be noted.

Jan 1, 1949

By Daniel I. Carey

Current and potential dragline reclamation usage was evaluated for the U.S. coalfields based on data gathered and analyzed during field surveys, literature reviews and contacts with manufacturers. It was concluded that current wining plans have been adapted to federal and state strip mine and reclamation laws in ways which limit the potential for drag line reclamation systems at active mine sites. At abandoned conventional contour mine sites in steep-sloping areas such as central Appalachia, however, it was found that dragline reclamation systems have great potential application and may be the only practical solution to many reclamation problems. Alternative dragline systems were examined for restoring abandoned sites, and it was concluded that a tower excavator system offered superior characteristics and should be evaluated and developed under field conditions. A testing program was developed to provide a framework for the monitoring and analysis of cost, production and environmental data during a field demonstration of a tower excavator system.

Jan 1, 1981

By Beardsmore G. R

Geothermal gradients in the Gippsland Basin commonly exceed 35¦ C/km. Consequently models of thermal maturation may indicate exploration targets with an anomalous age/depth distribution. However regional geothermal models are constrained primarily by observations of surface heat flow. High geothermal gradients may simply reflect the presence of low conductivity coal beds within the basin. Heat flow data are not readily available for the Gippsland Basin. Normally special purpose drill holes are required to provide direct determinations of surface heat flow. These provide core samples for thermal conductivity and allow measurements of a stable geothermal gradient at least one year after drilling. Different indirect procedures are now required to provide estimates for the Gippsland Basin. Bottom hole temperatures can be used with suitable corrections to provide an indication of the regional geothermal gradient. However the corresponding thermal conductivities are more difficult to determine. Geophysical logs can be used to detect the major lithologies but detailed statistical analysis is required for numerical estimates. Complex mixing models are now suggested for geothermal surveys linking physical properties to variations in the mineralogy of each well. Allowing for low conductivity coal measures the data in the Gippsland Basin suggest values for heat flow consistent with regional trends in Australia. Interpretation is complicated by overprinting of transient thermal events with different time scales. Apart from the tectonics of basin evolution geothermal signatures may be complicated by regional ground water migration, the 'hot spot' trace associated with southward younging of Cainozoic volcanism, diagenesis, and basin refraction.

Jan 1, 1992

By Kobayashi M, Kametani H

Particles of nickel flash furnace malle (45 per cent i) were oxidized in a dropping-particle furnace. The particles melted and the molten drops simulated those produced by the atomization of molten matte. The partly oxidized droplets were quenched and then reacted with silica flux to form high-grade matte (70 per cent i) and a fayalite slag. This paper describes the experimental equipment and deals with chemical aspects of the investigation such as volatile impurity distribution and thermodynamic considerations. The overall behaviour of minor elements such as Cu, Co, As and Pb was similar to that observed in conventional converting.

Jan 1, 1986

A combined reflection seismic and magnetic survey off the south coast of New South Wales has revealed six distinct reflection horizons within the Lower Triassic-Upper Permian sequence, and has enabled the upper part of the lllawarra Coal Measures to be mapped in considerable detail. Large magnetic anomalies in the eastern half of the survey area appear to originate in the Gerringong Volcanic Sequence which forms the magnetic basement in the survey. Small residual anomalies in the western half of the area can be correlated with small scale faulting and folding in the upper part of the llawarra Coal Measures, as revealed by the seismic reflection survey.A synclinal axis striking at approximately 55° has been mapped near the western margin of the survey area, and areas of faulting and folding have been outlined by combined analysis of seismic and magnetic results.

Jan 1, 1970

By David G. Borg

"Although researchers have realized varying degrees of success in numerics modeling, computer blast simulations and small scale in-situ testing, most will agree that the greatest uncertainty in total success stems from the uncontrollable field variables. Given the diverse nature of field conditiorencountered, no reliable and proven method of evaluating fragmentation quantitatively, and the lack of adequate field controls found in many operations, it is unlikely that a universal plug-in model will be developed for all blasting in the imediate future. This does not imply that all research devoted to modeling should cease, for it is precisely here where more research efforts are desperately needed."

Jan 1, 1989

By W. R. Reed, G. W. Luxbacher

As directed by the MINER act of 2006, the NIOSH Office of Mine Health & Safety Research (OMSHR) has annually awarded contracts to enhance mine safety and health. OMSHR has a history of research that focuses on both respirable coal mine dust and respirable crystalline silica (or quartz) dust, and contracts have been awarded since 2010 in support of our intramural research efforts. In 2018, a National Academies of Science consensus study report recommended expansion of respirable dust research. As a result, beginning in 2018 through 2021, eighteen contracts were awarded focusing on this area. These contracts can be grouped in three topic areas: characterization of coal/dust, development of real time monitors, and improvement of respirable dust controls. This paper summarizes the outcomes of completed contracts and the progress of current contracts.

Mar 2, 2022

By M. I. Copeland

The investigation of the iron-gadolinium phase diagram is part of a project undertaken by the Bureau of Mines and sponsored by the Atomic Energy Commission to investigate rare-earth alloys. Data from the investigation of the iron-gadolinium phase diagram revealed a single eutectic system with very limited terminal solubility and three intermediate phases. The eutectic point occurs at about 85 percent gadolinium, and the eutectic isotherm, which occurs at 850° C., extends from the compound Fe2Gd to 99-plus percent gadolinium. Very little solubility of the solid phases in each other was observed. The three intermediate phases, FegGd, Fe3Gd, and FeaGd, melt incongruently at peritectic isotherms at 1,320°, 1,150°, and 1,080° C., respectively. The crystalline systems of the three phases were determined as follows: FegGd, hexagonal; Fe3Gd, hexagonal or rhombohedral; and FeaGd, face-centered cubic. No lowering or raising of the alpha-gamma iron transformation at 910° C., the gamma-delta iron transformation at 1,388° C., or the gadolinium transformation at 1,262° C. was observed. The principal methods used in determining the iron-gadolinium phase diagram were melting-point determinations, thermal analyses, metallographic examination, and X-ray diffraction analyses. Melting, heat treating, and thermal analyses were conducted in a vacuum or under a helium atmosphere because of the avidity with which oxygen combines with gadolinium at elevated temperatures. A few hardness values were determined, but they had no part in the derivation of the phase diagram. No other mechanical properties were determined.

Jan 1, 1962

By A. C. Fieldner

This is the tenth annual report of research and technologic work conducted by the Bureau of Mines on the occurrence, properties, mining, preparation, and uses of coal and coal products. These annual reviews are guide's to the current work-and publications of the Bureau but do not replace the more complete reports published under the authorship of the individual investigators on specific problems in Bureau of Mines bulletins, technical papers, reports of investigations, and information circulars and in the technical press. The Annual Report of the Director of the Bureau of Mines to the Secretary of the Interior for the Fiscal Year ended June 30, 1945, summarizes the year's work on coal as follows: Coal and Coal Products The United States maintained its No. 1 industrial position in supplying fuel for war and in preparing for peace through more complete mining, improved preparation and up-grading of coal for special uses, and better utilization of coal in industrial establishments and homes.

Jan 1, 1946