Search Documents

By Yousef Mohassab, Hong Yong Sohn, Mohamed Elzohiery

As part of the development of a novel flash ironmaking process at the University of Utah, a labscale flash reactor was used to produce iron directly from iron oxide concentrate. This work tested the feasibility of the novel flash ironmaking process using the partial combustion of hydrogen as fuel and reductant. In this flash reactor, the energy required to reduce concentrate particles was obtained from the internal combustion of hydrogen and oxygen with complementary energy from electrical resistance heating to compensate for the heat loss. After the reaction shaft was electrically pre-heated, hydrogen and oxygen streams produced a non-premixed flame inside the reaction shaft. Various conditions such as flame configuration, flame power, positions of concentrate feeding ports, excess hydrogen amount and residence time were tested. More than 90% reduction of magnetite or hematite was achieved at temperatures as low as 1175 oC with < 100% excess hydrogen in <10 s of residence time.

Jan 1, 2016

By P. Wieser, D. Feke

"Priming of filters with small pores is influenced by the surface tension of the liquid metal and may be complicated by freezing • Freezing followed by melting has been observed experimentally. This process has been modeled on the basis of one dimensional heat flow by radiation to the filter and by conduction in the metal. Also considered are super-heat of the metal and the initial filter temperature. The results of the model provide useful guidelines for the application of filters. IntroductionFiltration has been recognized as a valuable method of refining by removing suspended phases from liquid metals or alloys. Woven fiberglass type fabrics and wire screens were used initially in the aluminum industry. With the introduction of the ceramic filters that exhibit improved inertness and refractoryness, filtration has been introduced to higher melting alloys including cast irons, superalloys, stainless steels, as well as low and medium carbon low alloy steels. A considerable literature is delveloping rapidly on the progress in applications and the advances in understanding the mechanisms and effectiveness of filtration processes (1-8).With the use of filtration for different alloy systems for the production of cast to shape parts a bewildering variety of gating system modifications has been developed (Figure 1) to accommodate the installation of filters in the mold. The modifications have two principal purposes: 1) the runner expansion is intended to compensate for the resistance to flow due to the filter and that of the captured inclusions, and 2) the metal reservoir upstream of the filter, provides a temporary by-pass which permits metal to flow across the filter and heat it until priming can be accomplished. priming of.filters by low and medium carbon steel is readily accomplished but, compared to such alloys as cast iron or 19 Cr-9Ni stainless steel, requires greater precautions to avoid failure to prime by excessive freezing on or inside the filter pores. This problem is further examined below:"

Jan 1, 1986

By Shunhong Huang

To improve understanding the effect of heavy metal chromium on soil biota, laboratory incubation experiment was carried out in the soils contaminated artificially with five concentrations of chromate (50, 250, 500, 1000 and 2000 mg kg_1 soil) over time (35 days). The population and diversity of bacteria, fungi and actinomycetes in soils were measured as indicators of soil microbial processes in the disturbances mentioned above. Incubation experiment results elucidated that the population and diversity of microorganisms decreased with increasing Cr (VI) concentration. Furthermore, various microorganisms showed different sensitivity to total Cr contamination. The sensitivity of microbial population to chromium contamination was in the order: actinomycetes >bacteria>fungi. The resulted implied that the microorganism can be used as an indicator of chromium contamination.

Jan 1, 2008

By Viviane Tavares de Moraes, Denise Crocce Romano Espinosa, Jorge Alberto Soares Tenorio, Adriana Johanny Murcia Santanilla

"Increasing volumes of solid waste are generated worldwide, due to the continuous technological advances, the electronic scrap is part of these waste, requiring the study of recycling processes to stimulate this activity or the reuse of its components. The separation of nickel from sulphate leach solution, which also containing iron, zinc and aluminium was carried out using bis-(2,4,4-trimethylpentyl) phosphinic acid (Cyanex 272) as extractant, in order to determinate the effects of pH and temperature. The number of stages required for extraction was also assessed. The results showed that the metal extraction increased with increasing pH. On the other hand, increasing temperature was not favorable for all metals. However, under conditions used in this paper the purification of solution containing nickel was possible.IntroductionIncrease in the demand of metals in the world for use in industry causes a great exploration of natural resources. One outcome of this is increased investigations for the recovery of metals from industrial wastes. Nickel is found in wastes, such as batteries and electric and electronic devices, this kind of waste becomes a significant source for metals recovery. Since nickel is also present in printed circuit boards, which are associated with electric and electronic equipment, it can be recovered from this kind of waste through different techniques. It is important to highlight that iron is generally associated with this scrap [1] and for its removal chemical precipitation is often used. On the other hand, the solvent extraction process is widely used for treatment of leach liquors, because it can be produce high purity solutions [2, 3]. This technique is based on the purification of solution using contact between a liquor leaching and the immiscible organic solution, which contains an extractant that promotes the desired metal transfer [4]."

Jan 1, 2012

By H. Forrest

Lead smelting at Cookson Industrial Materials was formerly carried out using a combination of Blast and Reverberatory Furnaces. In the late 70&apos; s these furnaces were replaced by two 20 tonne capacity Rotary Furnaces. This furnace type has proved to be more flexible in the range of feedstock that can be processed, including lead drosses, battery plate and even whole batteries. High rates of production have been achieved whilst attaining a good level of environmental control. The majority of the sulphur in the feedstock can be fixed by use of appropriate fluxes.

Jan 1, 1990

By P. V. Ananthapadmanabhan

Feedstock powders of metals, alloys and ceramics for thermal spray applications have to meet several specifications. Particle shape, size and distribution, powder flow characteristics and density are the important factors that need to be controlled, in order to ensure high spray efficiency and better coating properties. Thermal plasma technology can be effectively utilized to produce metal, alloy and ceramic powders for spray applications. The present paper describes plasma spheroidisation of commercially available aluminium powder and nickel-aluminium powder blend in a plasma reactor. Results show that the processed powder particles bear spherical morphology with excellent flow characteristics, which make them ideal for thermal spray applications.

Jan 1, 1997

By D. J. Cassidy

This document discusses commercial strategies and applications of specialty processing plants for the recycling of nickel, copper, zinc and cobalt bearing by-products. For this discussion, I will focus on materials originating from the metal plating, electronic circuit board· and chemical industries. The review of select processes and the required service, sourcing, material handling, processing and marketing strategies necessary for a successful recycling program are highlighted. Materials discussed in this summary include filtercakes, filters, dusts, spent catalysts, spent solutions and solids. Both pyrometallurgical and hyrometallurgical applications to these materials are addressed. A comparison of targeted finished markets, including smelter feeds and value added products are also reviewed.

Jan 1, 2000

By M. E. Karabin, R. J. O'Malley

"A mathematical model of the roll casting process has been developed which predicts macro-variables, such as roll separating force, roll torque, and strip exit speed for a range of roll speeds. Continuum variables, such as interface pressure, interface shear stress, freeze-front shape, and internal temperature distribution are also predicted.The model consists of two independent segments: solidification and rolling. The solidification model is two-dimensional (thickness and rolling direction) and is capable of handling alloy solidification. The solidification model is employed until solidification through the thickness is complete, then the rolling solution is activated.The rolling model is a one-dimensional (rolling direction) mechanical solution based on the von Karman approach, coupled with a two-dimensional thermal solution. The flow stress is expressed as a function of the average through-thickness temperature of the strip.Experiments were performed using a laboratory roll caster to test and refine the model. Experimental strip exit temperatures were used as input to the model. Experimental and predicted roll torque and strip exit speea were forced into agreement at a single reference roll speed to obtain values for the coefficient of friction and the interfacial heat transfer coefficient. Using these values, good agreement was obtained between predicted and experimental torque and strip exit speed over the entire range of roll speeds examined."

Jan 1, 1986

By R. A. Masumura, C. S. Pande, D. Agassi

"Grain size has a different effects on the critical current density (Jc) of high and low transition temperature (Tc) superconductors. In high Tc superconductors, the critical current density Jc across grain boundaries depends sensitively on the misorientation 8. It was pointed out by Pande that this dependence is directly related to dislocation structure of the grain boundaries i.e., it is due to dislocation cores and stresses. These ideas are developed further in this paper leading to a relation between Jc and 8. The analytical result is compared with the experimental results on bicrystals and used to explain the difference in behavior between high and low Tc superconductors.IntroductionThe grain size distribution and its evolution with time and temperature is important in determining the properties of high and low transition temperature (T c) superconductors. The distribution is a convenient function to characterize the processing of a high Tc material during sintering. For example, it is known that the maximum density of ceramic materials is obtained when the grain growth is reduced but grain boundaries are still mobile. For practical superconductors, the processing parameters are selected to achieve optimum properties: highest possible T c and maximum critical current (Jc). In terms of an average grain size, the requirements for optimum T c and Jc are sometime in conflict. In A15 type superconductors and even in NbTi, larger Jc have been measured in smaller rather than larger grain sized material. Conversely, in a high Tc materials like YBa2Cu307, higher Jc have been found in larger grain sized or single crystal specimens.Extended defects such as grain boundaries in low T c superconductors can be effective pinning agents for magnetic flux lines, thereby increasing the transport critical current density of these materials [1]. On the other hand, the transport critical currents in polycrystals of high Tc superconductors such as YBa2Cu307 is found to be relatively small (much smaller than those in single crystals of the same material) [2]. It is now known that grain boundaries in high Tc polycrystals can in many cases form ""weak links"" reducing the critical current density across them. This phenomenon can be studied more precisely by experiments on bicrystals, where there is only one grain boundary. It is found that the critical current density is quite sensitive to the misorientation angle of the bicrystal [3,4]. Although the original experiments were conducted on YBa2Cu307, other Tc superconductors have been shown to give the same result [5]."

Jan 1, 1994

By Laihua Wang, Peter Hayes, Hae-Geon Lee

"This paper introduces a new process for the efficient removal of dissolved gases and inclusions from liquid metals. This process involves the creation and dispersion of fine bubbles in molten metals by introducing inert or reactive gas into a region of turbulent flow. The highly turbulent metal flow splits the gas into fine bubbles and results in good mixing between the gas and molten metal phases. These conditions are ideal for contacting inclusions in the metal with the bubbles and subsequent flotation of the inclusions to the metal-slag interface where the inclusions are then absorbed by the covering slag layer. Dissolved gases, such as [H], [0], [N] in the metals are also transferred to the gas bubbles and removed from solution.The process concept has been previously demonstrated using a full-scale air/water model to simulate the ladle-to-tundish system of continuous casting of steel. The present cold modelling work has further demonstrated the ability of the process to remove gas solutes. The results indicate that the efficiency of new process is several hundred times greater than that of conventional high speed rotating injectors which are currently applied in the treatment of liquid light metals.IntroductionDuring metal smelting, refining and alloying processes, unwanted gas and second phase liquid or solid impurities are incorporated into liquid metals. In the case of steelmaking, the gas-forming impurities include [0], [H] and [N], and the solid impurities as a result of deoxidation include Ah03, Si02 inclusions. Common impurities in liquid aluminium are dissolved hydrogen and solid Ah03. To avoid subsequent problems during processing and to improve the physical properties of the metal products it is necessary to significantly reduce the level of impurities."

Jan 1, 1996

By A. V. Tarasov

An environmentally clean and virtually waste-less technology for treatment of domestic solid waste and other toxic chloride-containing materials has been developed and proven on a full scale by the Gintsvetmet Institute in cooperation with some other Russian organizations. The proposed process resolves the acute and globally significant problem of dioxin formation. The purpose of the proposed technology is to ensure such destruction of the structural lattice of toxic compounds that would guarantee irreversible transformation of the resultant substances to prevent formation of dioxins. The preconditions that are required to achieve this purpose are: temperature of >125O0C; an oxidant excess coefficient of >I .05; a certain retention time of the products under these conditions (ADZ s); and thermal instantaneousness of the process involving a transition with no intermediate phase. These conditions were achieved with the experimental development of the Vanyukov furnace design commonly used for sparged smelting processes at non-ferrous metallurgical plants in Russia and Kazakhstan.

Jan 1, 2002

By Onwukamike, Onyedika G. O, Ogwuegbu M. O. C., K., Onyenehide C

A detailed mineralogical and elemental characterization of a lead (Pb) ore deposit from Ishiagu, Ebonyi State, Nigeria was carried out with XRD, SEM-EDX, and ICP-OES based mappingtechniques. The results show that the most dominant and valuable metal is lead (Pb = 95.02%, mass fraction). The main mineral is galena. Ilmenite and sphalerite occur as minors, which account for 2.71% and 0.80% respectively. Elements like Al, Ca, Mg, Ti, Na, Mn, Si and Sn occurred in trace amounts and are disseminated in the entire ore body.The surface and interrelations of the crystals were examined with x-ray mapping and the result shows the pattern of dissemination of the minerals within the ore body.

Jan 1, 2015

By Hideya Sato

Refractory wear caused by melts is one of the major determining factors for the interval of shut-down repair of the metallurgical furnaces in general. Calcium ferrite slag employed by M it subishi Continuous Copper Converter, shows hi& fluidity and corrosive characteristics against most of the refractories. In order to improve the corrosion resistance of the refractories, the mechanism of MgO-based refractory wear by the calcium ferrite slag was intensively studied. The dissolution behavior of the refractory into the molten slag and the penetration of the molten slag into the refractory were observed by crucible tests and newly developed oscillating furnace tests. It was found that the wear of MgO-based refractories by the calcium ferrite slag is mainly dominated by the internal structural failure caused by the penetration of CaO-Cu20 rich slag which is formed as a result of the preferential absorption of FeO, from original slag by the spinel of the refractory.

Jan 1, 1999

By J. -C. Tedenac, C. Colinet, X. Tao, P. Jund, R. Viennois

"We report an ab-initio study of the stability and electronic properties of transition metal silicides in order to study their potential for high temperature thermoelectric applications. We focus on the family M5Si3 (M = Ta, W) which is stable up to about 2000 °C. We first investigate the structural stability of the two compounds and then determine the thermopower of the equilibrium structure using the electronic density of states and Mott’s law. We find that W5Si3 has a relatively large thermopower but probably not sufficient enough for thermoelectric applications.IntroductionIn the search of new sustainable energies, thermogeneration of electricity is one of the promising ways, notably because it is able to produce electricity from different kinds of heat wastes and to its portability. However, despite recent progress in the field, the state-of-the art materials have specificities making their mass-production difficult or even impossible: toxicity (thallium, chalcogen or/and pnictogen based alloys), weak abundance (tellurium based alloys) or cost (germanium or rare-earth based alloys). For all these reasons, finding thermoelectric materials without these drawbacks is vital if we wish to use high temperature thermoelectricity for generating electricity in the near future. Due to their abundance, low cost and low toxicity, transition metal silicides are candidate materials of primary interest and the slightest advance in this field would immediately find an application for the thermogeneration of electricity."

Jan 1, 2011

By Paul Dewison

For nine years, from mid-1987 to mid-1996, the copper market enjoyed what appeared to be an endless boom in which prices were much higher relative to production costs than for most other base metals. After the boom ended abruptly mid-1997 with the Sumitomo affair, copper was burdened by an overhang of new projects that promised to swamp demand in what, with the Asian financial and economic crisis of 1997, had become a considerably worse consumption environment. Now, demand prospects do not look so bad. If, as we suspect, we will be dealing with a more rational market in the future, it becomes all the more important to forecast accurately the prospects for consumption. In this paper, we present a new methodology for copper demand forecasting. The methodology forms the backbone of the demand-side analysis for the multi-client study entitled "Long Tenn Outlook for Copper", co-authored by Metalica Ltd. and Bloomsbury Minerals Economics (BME). Key components of the methodology are as follows. (1) Relate demand to economic structure. (2) Focus on products rather than refined consumption. (3) Apply a consistent products/applications analysis to all countries and time series. (4) Incorporate scrap market dynamics within the analytical framework.

Jan 1, 1999

By John J. Mahoney, George P. Demopoulos, Matthew T. Bohan

In recent times processing of arsenic-laden complex ores and heightened awareness of the detrimental health effects of arsenic has put an increasing burden on metallurgical operations to remove arsenic from processes for disposal in an environmentally stable form. At present, arsenic is removed and prepared for storage by precipitation of insoluble secondary arsenic-bearing minerals. It has been suggested that Ca(II)-Fe(III)-As(V) phases resembling the natural mineral yukonite, under certain conditions, may have a role in controlling arsenic pore water concentrations in arsenical waste storage facilities. In this study, a previous synthesis method of yukonite (Ca3Fe5(AsO4)4(OH)9⋅4H2O) is revisited and new solubility/stability data is presented based on a modified method.

Jan 1, 2014

By Ronald Klepper

In hydrometallurgy, pure gases like oxygen and hydrogen are used for oxidation and reduction. The gases are expensive and therefore should be used efficiently. Non reacted gas can be recycled into the liquid. Historically vortex gassing has been used; Le. a mixing impeller close to the liquid surface entrains gas from the headspace into the liquid through a gas vortex. Novel and more efficient methods are surface gassing with up pumping impellers and self- inducing gassing impellers. These alternative impeller systems are well established and common in the chemical industry, but have not been used until recently in hydrometallurgy. Gassing impellers act as internal compressors and increase the interfacial surface for a much higher mass transfer compared to alternate methods mentioned. In the paper results from lab and pilot tests and data from operated plants will be presented. The reactions with gases normally take place under moderate to high pressure, therefore a safe enclosure with mechanical seals and the safety "philosophy" is important. Experienced life and replacement cycles will be reported.

Jan 1, 2000

By Thenepalli Thriveni, Ch. Ramakrishna, Yujin Jegal, Ji Whan Ahn, Jyothi Rajesh Kumar

In alumina production or alumina refining, bauxite is converted to alumina (aluminium oxide) The rare-earth elements (REEs) are a group of 17 chemically similar metallic elements (15 lanthanides, including scandium and yttrium). Rare earth elements play a key role in many industrial applications, petroleum refining, clean energy, automobile, electronics, and defense applications. These rare earths are essential to the success of green technologies. China today controls more than 95 percent of the rare-earth supplies and nearly all rare-earth refining and after 2009 year rare earths crisis raises due to China’s export restrictions and growing internal demand for rare earth elements. The extraction of gallium and yttrium from Korean red mud (KC red mud) by selective acid leaching was explored. The recovery of gallium and yttrium from a leach solution of the Korean red mud using solvent extraction was studied. A number of extractants were investigated for the extraction of those mentioned two rare earth elements and also we proposed a flow sheet of rare earth elements respectively. The toxic heavy metals presented in KC red mud were removed by CO2 stabilization.

Jan 1, 2015

By R. Rajiv Srivastava

Brine leaching of a TSL processed zinc-plant residue (ZPR), containing 83.3% anglesite, has been investigated for lead recovery. A prior treatment of ZPR in acid solution did not show any significant effect of acid concentration in zinc dissolution. The study reveals that the solubility limits of PbCl2 is as an important factor with respect to the brine concentration and pulp density in lixiviant. The dissociated sulfate ions hinder the formation of PbCl2 on prolong leaching (above 60 min), while exhibiting the reverse solubility of lead as PbSO4. A 3-step leaching process could yield >92% leaching efficiency when the parameters were maintained as: 10% pulp density in a 250 g/L NaCl solution, 80 °C temperature, and 60 min time. This leaves the insoluble ferrite, sulfides and oxy-sulfates of zinc and lead in the final residue as revealed by the XRD characterization.

By Zhucheng Huang, Ronghai ZHONG, Tao Jiang, Jun ZOU

The method of reduction roasting and magnetic separation of low-grade, micro- fine disseminated refractory iron ore following granulation with coal produced unexpected success. Pellets of iron ore with diameter between 3 and 8mm were granulated with coal, bentonite and water. The raw pellets and reduction products were analyzed by scanning electron microscopy and x-ray diffraction. Results show uniformly distributed coal powders inside the pellets improved the kinetics of the reduction process and accelerated the reduction rate. Reduction time was higher at temperatures below 890℃, which resulted in the formation of substantial amounts of fayalite. When temperature was increased, micro- fine hematite was then quickly reduced to iron metal and the amount of fayalite decreased sharply. When pellets were reduced at 950℃ for 25min, reduction products with 56.73% metallization rate were obtained. After grinding and magnetic separation, a concentrate with 72.18% Fetot was obtained.

Jan 1, 2015