Search Documents

By M. J. Bagshaw, J. D. Hunt, R. M. Jordan

"Continuous casting processes, and the roll casting process in particular, offer considerable potential to the Aluminium industry, both meatallurgically and economically.The three major limiting process problems that occur during roll casting are Centre Line Segregation', 'Sticking' where metal adheres to the rolls during casting, and 'Heat Line' formation. 'Heat Lines' are localised semi-continuous longitudinal defects, usually a few cms in width, where the cast metal leaves the roll bite partially molten. These defects occur at relatively low casting speeds when the mean slab exit temperature remains several hundred degrees below the solidus temperature. The objective of the work described here is to develop a better understanding of the roll casting process in general, and in particular, to understand the phenomenon of 'Heat Line' formation.A steady state two dimensional finite difference model has been developed to describe the roll casting process, incorporating a variable heat transfer coefficient through the roll bite. In the model the difference equations are formulated using a control volume method and latent heat is incorporated according to the Scheil equation. A Gauss-Seidel type technique is used to obtain the solution. Because the rate of heat evolution is non-linear the temperature in each box is determined by using a Newton-Raphson method. The solution for a box can be multi valued and therefore lead to instability particularly near the vicinity of the front. A stability 'criterion is presented which shows that to obtain a stable solution it is better to have long narrow boxes rather than boxes with small dimensions in both directions.The model explains why heat lines form in terms of the variable slab/roll heat transfer coefficient.Experimental measurements of slab exit temperatures are also presented. These were obtained on a Hunter twin roll caster for the binary AI-Cu system, at two compositions over as wide a range· of casting speeds as possible. The experimental results are compared with the predicted ones."

Jan 1, 1986

By Jun Li

Rate processes of silver cyanidation were studied with the objective of understanding the reaction mechanism. The research was divided into three sections: anodic dissolution of silver in cyanide solutions, cathodic reduction of oxygen on silver surfaces and the direct leaching of silver in oxygenated cyanide solutions. The charge transfer steps plus the diffusion of reactants from bulk solutions to the silver surface were identified as rate-limiting and the rates of both anodic and cathodic reactions can be calculated using the Butler-Volmer equation and Fick's first law. Based on mixed potential theory and the results of electrochemical studies, a comparison of the rate obtained from direct leaching with that predicted from the calculation is made. Calculated results agree well with the experimental data.

Jan 1, 1992

By C. J. N. Buisman

THIOPAQ technology developed and marketed by PAQUES Bio Systems in Balk, Netherlands, has been successfully used at commercial scale at the Budelco zinc refinery in the Netherlands for the treatment of contaminated groundwater since 1992. In essence, THIOPAQ technology consists of two biological process steps in series: sulfate reduction to hydrogen sulfide (anaerobic) and sulfide oxidation to elemental sulfur (aerobic). The biogenic sulfide produced can be employed for the chemical precipitation of metals in solution either inside the anaerobic reactor or in a separate vessel. Since the solubilities of most metal sulfides are much lower than of their respective hydroxides, considerably lower effluent metal concentrations can be achieved with THIOPAQ systems than in neutralization processes which immobilize metals predominantly by hydrolytic precipitation. In recent years, PAQUES has made significant advances in the design and operation of aerobic and anaerobic bioreactors for metal-sulfur systems. Moreover, the company has increased its technology portfolio to allow the development of more process oriented applications of THIOPAQ technology. A new PAQUES designed plant at Budelco treating sulfatecontaining proceswaters will be started up in 1999. The sulfate reduction is accomplished in a 500 m3 reactor in which hydrogen is used as electron donor. The endproduct, ZnS, is used for Zn and H2S04 production.

Jan 1, 1999

By J. Smuts

The mixed-valence iron silicate ISCORITE (Fe7Si010) was identified recently in a number of ironmakingmater1als, some of which were first produced more than a century ago. Although the existence of iscorite was not reported before 1967 and published phase diagrams do not make provision for it, the morphology of the phase in all the materials that were examined suggests that it is stable under a variety of conditions. It is shown that is-corite can accommodate various foreign cations in its lattice where they can replace Fe and/or Si. The morphology of is-corite in a number of materials of different origin is shown in relation to iron oxides and silicates in optical and SEM/BSE images.

Jan 1, 1991

By R. Y. Wan

Low grade sulfidic-carbonaceous refractory ore from Newmont Gold Company's Carlin deposit was microbially pretreated. The biological pretreatment process gave partial oxidation of the sulfidic components of the refractory ore but the preg-robbing carbon continued to be active resulting in approximately zero cyanide gold extraction. A 495 ton pilot plant test heap was conducted using acidic thiourea leach following biooxidation. Activated carbon and cation exchange resin adsorption were tested for gold recovery from the thiourea pregnant solution. The results obtained from the test heap were not satisfactory. Gold extraction was low due to slow reaction kinetics which was caused by relatively large particles and very low winter temperatures. Problems existed in the thiourea-test heap and are discussed in this paper. An alternative heap leach process using thiosulfate has been successfUl at the pilot scale for gold extraction following biooxidation pretreatment of refractory sulfidic-carbonaceous ores.

Jan 1, 1995

By D. C. Foguel, J. L. R. Bravo

For several years, Caraiba Metais S.A. (CMSA) had to stock the arsenic sludge generated from the electrolyte purification process of its tankhouse. The amount stocked · reached approximately 3,500 tonnes, as the effects of its recycling during the smelting process and consequently in the sulfuric acid plant were unknown. Besides, it had as limiting factors the high content of arsenic in the copper concentrates supplied by foreign countries as well as the reduced capacity of the tankhouse's purification plant. The choice for selling the mentioned residue, which generally contains more than 50% of Cu, was attractive, but the environmental policies and regulations had not allowed this option. Other alternatives, such as the production of bicupric arsenic by means of a solvent extraction process or arsenic trioxide, were considered but the economic feasibility was not attractive due to the absence of a domestic market and a poor international market. After a study of the arsenic partition in the metallurgical process, it was verified that the residue could be recycled without causing any operational problems or damage to the environment. To make this possible, the capacity of the purification plant was increased and the way of removing the arsenic sludge from the cells was modified from manual to mechanical, therefore avoiding the direct contact of the workers with this poisonous substance. Moreover, procedures for recycling in the smelter were established and tolerance limits were set for both the smelter and the sulfuric acid plant. The main amount of arsenic to be recycled is released with the smelting furnace off-gas, which is washed during the purification stage of the sulfuric acid plant. The acid water, rich in arsenic, is then treated in the waste plant and the arsenic, in its stabilized condition, is confined in an appropriate area.

Jan 1, 2000

By Ian Masters

Rotary furnaces are widely used throughout the metals industry. These furnaces vary in size and geometry, but are fundamentally the same from a thermodynamic viewpoint. A generic method is proposed that can be used to model all furnaces of this type, provided that the correct material and process parameters are known. Various approaches have been attempted in the past based on a continuum (FEA or CFD) approach. However, the complex fluidlsolid interactions present in a rotary vessel are not easily solved using these methods, which work best where the material boundaries are well defined. In this paper a lumped parameter model is proposed. Variations within a section of the model are ignored, but to ensure thermodynamic correctness, the heat transfer between sections is carefully considered. For example, it is reasonable to assume that the whole of the melt pool is at the same temperature, due to rotary mixing. This may then be modeled with a single set of parameters, and the detail is contained in obtaining the correct heat transfer mechanisms from the rest of the furnace.

Jan 1, 2002

By M. Nilmani, H. Pham

"A mathematical model was developed for the dissolution of particles in gas-stirred liquid baths, linking the hydrodynamic flow field of the bath, the average particle trajectory and liquid-side mass transfer controlled dissolution kinetics. The model was validated by comparison with experimental data for the dissolution rates of urea particles in gas-stirred aqueous CaCl2 solutions measured during this study. The dissolution rates of urea. particles were measured using an image analysis system.The effects of operating conditions on the dissolution rates of urea particles were investigated. It was found that the key operating parameters influencing the utilisation efficiency of particles were the gas flowrate, particle diameter and lance submergence. An optimisation of the operating conditions for the model urea-aqueous CaCl2 system indicated that the utilisation efficiency increased with decreasing gas flowrate and decreasing particle size for a given lance submergence.IntroductionThe utilisation solid reagents in molten baths varies from one process to another, depending upon the rates and mechanisms of the reactions between the particles and melts, as well as the trajectory and residence time of the particles in the melts. Previous studies have not attempted to predict the utilisation efficiency of injected solids by coupling the motion of the particle with its dissolution rate. Instead, the particles have usually been assumed to remain suspended in the bath until completely dissolved, and the mass transfer coefficients were based on the average specific mechanical energy dissipation rates in the bath. Investigations of this nature relevant to the present study have been undertaken by Apelian et al. [1], Brucato et al. [2] and Langberg and Nilmani[3]. The objective of the present study was to develop a mathematical model, incorporating both the reaction kinetics between the particles and liquid and the particle motion simultaneously, to predict the dissolution rates and times of the particles. The mathematical model was validated by comparison with experimental dissolution rates of a cold model analogue system measured using an image analysis technique, and then applied to optimise the operating conditions in the model system."

Jan 1, 1996

By C. Dresen

This paper discussed the reaction kinetics of the reduction of industrial phosphate pellets for P4 production. In the reduction process of various phosphate ores, the following parameters were investigated: Diffusion of the phosphorus oxide and other gaseous products from the reaction mixture after having been reduced on the reductant (coke) surface. Influence of silica on reaction kinetics. Temperature influence. Influence of mineralogy and morphology (different ores). Particle size influence of silica and coke. Experiments were carried out in a vertical tube furnace with 2 ores, 2 types of silica and one type of coke. Selected experimental conditions simulated furnace conditions. The following conclusions could be made: Reaction rate increases with the addition of SiO2 into the pellet. The reaction rate increases above 1350°C (melting temperature of the slag). Mixing different ore types in the pellets leads to differences in reduction kinetics. Particle size of the coke particles influence reduction kinetics. The amount of slag formation is influenced by silica addition, coke size and temperature.

Jan 1, 2002

By Esher Hsu

On July 5, 1997, Environmental Protection Administration of Taiwan publicized the recycling regulation of waste home appliances that include four items, namely, television, refrigerator, washing machine, and air conditioner. It is believed that this regulation pioneers the law enforcement of waste home appliances in the world. The objective of this study is to provide helpful base for amending recycling rates of waste home appliances. This study investigates the collection and recycling costs of waste home appliances in accordance with these newly established routes and facilities, respectively. Cost survey was conducted among collectors and recycling plants of waste home appliances; consequently, the collection and recycling costs were analyzed, correspondingly. Results provide some suggestions regarding recycling route, recycling system, recycling rates paid by manufactures and importers, recycling subsidies to collectors and recyclers. Those suggestions may provide useful policy implications to EPA for the future decision-making regarding the recycling of waste home appliances.

Jan 1, 2003

By Shize Jin

Effect of four polyols, namely ethylene glycol (EGL), glycerol (GCL), propanediol (PDL), butanediol (BDL) and three organic acids, namely oxalic acid (OA), malonic acid (MA) and succinic acid (SA) on the current efficiency (CE) and the cell voltage during zinc electrowinning was studied. Galvanostatic polarization was conducted in a supporting electrolyte (SE) containing 180 g dm-³ H2SO4, 60 g dm-³ Zn2+ and 8 g dm-³ Mn2+ at 38°C with magnetic stirring. The imposed current density was 50 mA cm-². The anodes were made of a Pb-Ag alloy and the cathodes were made of an aluminum alloy. The results showed that all the polyols tested in this study decreased the current efficiency and the cell voltage, but the decrease of the cell voltage was not important. Oxalic and succinic acids decreased the current efficiency to a less extent than the polyols, but did not decrease the cell voltage much. The only compound that increased the current efficiency was malonic acid, and its capacity of decreasing the cell voltage was the highest within the seven tested organic compounds.

Jan 1, 2003

By J. J. Moore

The application of plasma technology to process metallurgy is briefly discussed. Experiments involving in-flight reduction of minerals (taconite, chromite, in particular) with a solid-based carbon reductant are described. The resultant metallic and slag product analysis is discussed with respect to thermodynamic and kinetic considerations.

Jan 1, 1985

By Donna L. Bodine

The ability of oxidized Upper Freeport bituminous coal to adsorb Cu2+, Cd2+ and Mn(VII) from very dilute aqueous solutions has been studied. Low-rank coal is known to adsorb heavy metal ions from dilute, aqueous solutions, probably by ion exchange and/or chelation by acidic functional groups on the coal surface. However, it would be advantageous to use higher rank coals for water treatment. Coal samples were oxidized thermally or by 30% H202 to increase the surface concentration of phenolic and carboxylic groups, then portions were shaken with Cu2+ and Cd2+ solutions. Acidic KMnO4 was also used to oxidize coal, with concurrent sorption of the resulting Mn(IV) and Mn(ll). The effect of oxidation treatment, metal ion concentration, and solution pH on metal uptake kinetics was investigated. Potential applications for treating effluents, especially those containing oxidizing ions, are discussed, along with possible flowsheet options.

Jan 1, 1995

By Jie Ma, Bo Wang, Jieyu Zhang, Jian Zhao, Zheng Chen

"In this paper, solidification process of steel ingot was simulated by ProCAST software, based on cellular automaton-finite element (CAFE) model. A 22 t steel ingot was divided into continuous small zones (100x150x180 mm) in radial direction, then the temperature field, shrinkage cavity and porosity, particularly, the microstructure were simulated. The results show that: there was a columnar-to-equiaxed transition in microstructure on radial direction. Zones, closing to the center of the ingot, had a more developed and fined equiaxed zone, while zones closing to the periphery of the ingot had a more developed columnar zone. It indicated that temperature gradient has a great influence on microstructural morphology. Thus, the simulation results were highly agree with the experimental results, verifying the feasibility of this simulation method. It significantly reduces the time of simulation, and has important significance for predicting the microstructure of large steel ingot.IntroductionSolidification microstructure of steel ingot have a significant effect on the quality of the final steel products. Although many experimental works have been carried out in order to obtain the optimum condition for solidification process of continuous casting, it is also very desirable to establish mathematical models to simulate the evolution of solidification structure. The simulation methods can be divided into deterministic models and stochastic models, which have been developed rapidly over the last couple of decades. Cellular automaton method is one of the stochastic models. Rappaz and Gandin [1, 2], Nasatac and Stefanescu [3, 4] are the earliest researchers engaged in the this field. Moreover, Rappaz and Gandin simulated the solidification structure and CET (columnar grain to equiaxed grain transition) of metals using the CAFE method (cellular automaton-finite element method) for the first time [1, 2]. Recently, the CA (cellular automaton) model also considered the effects of fluid flow on the solidification process. Zhu, et al. [5-11] improved method of CA , they used the KGT model to describe the undercooling needed during the growth of the dendrite tip."

Jan 1, 2014

By T. T. Chen

Secondary copper anodes are generally rich in Sn, Pb, Ni and Sb, but are notably deficient in Se, Te and Ag. In the secondary copper anodes, most of the Ni, virtually all of the Ag, slightly more than one-fifth of the Pb, about one-third of the As and Sb, and approximately one-tenth of the Sn are in solid solution in the copper. The remaining impurity contents occur as 1-5 µm grain-boundary inclusions in the anodes, and these are mainly Cu2O, SnO2, Cu-Pb-As-Sb-Bi oxide, Pb-Sb oxide, Sn-Ni-Zn oxide, Cu-Sn-Ni oxide, Cu-Sb-Ni oxide (Kupferglimmer) and trace Cu2(Se,Te). Barium sulphate, which originates from the mold wash used in casting, is also present in the anodes. During electrorefining, the BaSO4, SnO2, Pb-Sb oxide, Sn-Ni-Zn oxide, Cu-Sn-Ni oxide and Cu- Sb-Ni oxide inclusions are liberated and accumulate in the slimes layer. Solid solution Ni dissolves and the Ni accumulates in the electrolyte. Solid solution Sn and Pb dissolve, but partly reprecipitate as Sn arsenate and PbSO4, respectively. Solid solution Ag dissolves but rapidly reacts to form Ag2(Se,Te), Ag powder, Ag-bearing Cu2O, (Cu,Ag)SO4 or a complex oxidate phase. Partial dissolution of the Cu-Pb-As-Sb-Bi oxide particles takes place; the Pb component is converted to PbSO4, whereas Cu, As, Sb and Bi dissolve. The reacted particles retain the morphology of the original Cu-Pb-As- Sb-Bi oxide phase. Some of the solubilized As, Sb and Bi remains in solution, but much reprecipitates as SbAsO4, As-Sb-Bi oxide, and as a poorly defined oxidate phase which consists mostly of Cu-Ag-Pb arsenate-sulphate. The high Sn contents of secondary copper anodes do not seem to affect the behaviour of the anodes during electrorefining.

Jan 1, 1999

By R. Dekkers

Non-metallic inclusions in liquid steel are mainly formed during killing. As far as these particles are not captured by the slag, they are found in the cast steel where they can deteriorate the mechanical properties. Inclusions may also disrupt the continuous casting process, affecting thus directly the quality of the steel and the production capacity. Steel pin samples from the Sidmar plant (Belgium) were taken in different steps of several ladle treatments and in the tundish. Also slab samples were studied. All samples concern the same type of low alloyed aluminium killed steel. The non-metallic inclusions were isolated from the steel matrix and investigated with scanning electron microscopy and energy dispersive spectrometry. The evolution of the non-metallic inclusions is described by their number, size, shape and elemental composition. The main non-metallic inclusions present are aluminium oxides and spinel type compounds.

Jan 1, 1999

By P. D. Nolan

Smelters operating under pollution control orders have become increasingly dependent upon the reliable operation of sulphuric acid plants and no factor affects the long term reliability of those plants more than efficient gas cleaning. The sources and characteristics of contaminants in smelter of fgases and the conventional approaches to removing these contaminants to accepted levels are discussed. New technology is described which offers advantages of lower capital cost, lower operating cost and reduced space requirements over the conventional approaches. This new technology has been developed by LAB s.a. and is licensed for metallurgical gas applications by Chemetics International Company.

Jan 1, 1983

By Antonio Martin, Jesus Hurtado, Francisco Jimenez

"Atlantic Copper is one of the largest copper producers in Europe. Its production facilities, including a primary copper smelter and an electrolytic refinery, are located in Huelva, on the southwest coast of Spain. These installations enable the smelting of over 1 million tpy concentrates to produce up to 260,000 tons per year of cathodes and 900 ktpy of sulphuric acid.Since 1970, several improvements have been made at the Converters Area such as modifications of primary hoods, operations with an OPC system, installation of scrap chargers, the recent installation of the secondary hoods and other environmental projects. All these modifications have been aimed at increasing the capacity of our smelter while keeping our continuous environmental commitment.This paper describes the modifications and improvements carried out at the converters area and our proposals for future developments."

Jan 1, 2012

By Dmitri Goljandin, Jaan Kers, Xiangjun Zuo, Lifeng Zhang, Priidu Peetsalu

"In this paper, the mechanical milling of the electronic wastes was carried out. The metal parts and plastic parts were roughly separated. The final plastic powder size could be as small as ~100 µm. Then the pyrometallurgical recycling Printed Circuit Boards (PCB) was executed. The mechanisms of thermal degradation and combustion are investigated using TG/DTA and MS. Some chemical powders, such as Na2CO3, NaHCO3, NaOH and CaCO3 are used to control the exhausted toxic gas such as Br2. Introduction Waste electric and electronic equipment (WEEE), or electronic wastes (E-wastes), has been taken into consideration not only by the government but also by the public due to their hazardous material components [1-3]. From the point of material composition, electronic wastes can be defined as a mixture of various metals, particularly copper, aluminum, and steel, attached to, covered with, or mixed with various types of plastics and ceramics [4]. Precious metals have a wide application in the manufacture of electronic appliances, serving as contact materials due to their high chemical stability and their good conducting properties. Platinum group metals are used among other things in switching contacts (relays, switches) or as sensors to ascertain the electrical measurand as a function of the temperature [5]. Table 1 [6] gives examples of the metal composition of different electronic scraps from literatures. Additionally, non-ferrous metals and precious metals content have gradually decreased in concentration in scraps. The value distributions for different electronic scrap samples are shown in Table 2 [6], where the metal price data are from London Metal Exchange (LME) (Octoebr 2007). It can be seen that for cell phones, calculators, and printed circuit board scraps, the precious metals make up more than 70% of the value, for TV boards and the DVD player they still contribute to about 40%. This indicates that the major economic driver for recycling of electronic waste in industry is from the recovery of precious metals. Behind the precious metals come copper and zinc, while Al, Pb, and Fe are less value. Recycling of electronic waste is an important subject not only from the point of waste treatment but also from the recovery aspect of valuable materials."

Jan 1, 2008

By Derk G. E. Kerfoot

The extractive metallurgy of nickel and cobalt has proved to be a particularly fruitful area for innovation in hydrometallurgy and electrometallurgy ever since the development of the Hybinette process for nickel in the early 1900's. In current practice, nickel concentrates are generally smelted to high grade mattes which are then refined to metal by a combination of hydrometallurgy and electrometallurgy, although low grade copper-nickel concentrates are refined directly by the ammonia pressure leach process. Matte refining processes in commercial operation include the direct electrolysis of matte, the ammonia pressure leach, sulphuric acid leaching using air or oxygen at elevated pressure, or at ambient pressure, and chlorine or chloride leaching. Refined nickel is recovered either as electrolytic cathode, or as metal powder by hydrogen, reduction. Hydrometallurgy has also found application in the treatment of nickel laterite ores, both in the reduction roast ammonia-ammonium carbonate leach process, pioneered by Caron and in the Moa Bay acid leach process. Cobalt is recovered as a co-product of copper in central Africa, and as a byproduct of hydrometallurgical nickel refining elsewhere. In the African plants, the copper-cobalt concentrates are roasted and leached in sulphuric acid solution, and copper and cobalt are recovered separately from the leach solution by direct electrowinning. A variety of hydrometallurgical techniques are used for the separation of cobalt from nickel, including selective precipitation and crystallization, solvent extraction, and ion exchange. Like nickel, refined cobalt is recovered either as electrolytic cathode or as metal powder by hydrogen reduction.

Jan 1, 1988