Search Documents

By S. J. Schatzel

Coal mine longwall face ventilation is an important component of the overall mine ventilation system. Increases in the production rate due to higher capacity mining equipment tend to increase methane emission rates from the coal face, which must be diluted by the face ventilation with a minimal opportunity for assistance from additional control equipment (i.e., surface boreholes). Increases in panel length, in some mines approaching 6,100 m (20,000 ft), and panel width provide additional challenges to face ventilation designs. Face ventilation can also be affected by communication with the methane-laden gob gas reservoir. Except in a two-entry system, belt air cannot be used to ventilate the face in the US, except in limited cases. This relatively recent requirement has further challenged the mining industry in maintaining adequate longwall face ventilation. To assess the effectiveness of current face ventilation practices, a face monitoring study was combined with a tracer gas test on a longwall face. The study was conducted at a US mine operating in a thick, bituminous coal seam with some self-heating tendencies. Multiple gob gas ventholes were located near the face and produced a small portion of ventilation air in their production flow. Initial results show that emission rates on the longwall face showed a very limited increase in methane concentrations from headgate to tailgate despite the occurrence of methane delays during monitoring. Increases in methane concentrations in the tailgate entry in the vicinity of the longwall face T-junction appeared to be produced primarily by gas flow from the gob, not from increased emissions from the face. Barometric pressure variations were substantial over the course of the study and varied on a diurnal basis, as is typical of many mining operations. Suggestions are forwarded for reducing longwall face methane concentrations.

Jan 1, 2012

By J. Chai, H. H. Sedarat, Gary J. E. Kramer, A. Kozak

Precast concrete segmental lining systems have been gaining widespread use in seismically active areas and a single-pass version of such a system has been developed for use on the Silicon Valley Rapid Transit (SVRT) Project in San Jose, California. The response of tunnel linings to seismic shaking is often predicted using engineering judgment, elastic closed-form solutions and numerical modeling. Such analyses generally assume a continuous structural system and hence do not explicitly model the behavior of the jointed segmental lining. A number of analyses were performed to predict radial and circumferential joint behavior during seismic ovaling and wave propagation. These analyses included a complex, three-dimensional finite element based ground-structure interaction model that incorporates inelastic constitutive soil behavior, cracked concrete properties and no-tension, frictional segment joint surfaces. The paper discusses the results of the analyses and provides guidelines for the design of precast systems in zones of high seismicity.

Jan 1, 2007

By John J. Murray, Michael T. McRae, Michael A. Krulc, Kathy L. Schuler

The San Vicente Pipeline Tunnel Project involves the construction of an 8.5-foot-diameter water pipeline in an 11 mile tunnel in San Diego, California. The tunnel is located in extremely variable geologic conditions of strong granitic and volcanic rocks, weak sedimentary rocks, abrasive conglomerates, and mixed face conditions. One reach of the tunnel is a 5,200-foot mixed face reach that includes Friars Formation Conglomerate overlying granitic rock. Due to the variable ground conditions in this reach, the use of a TBM was deemed too risky and the contract documents required drill-and-blast and hand mining methods. Although it was not required, the contractor elected to construct this reach using NATM methods. This paper describes the geology of the 5,200-foot mixed-face reach, the design evaluation, and the construction challenges faced on this project.

Jan 1, 2007

By A. J. Kwitowski

Remote control is usually associated with deep mine, continuous mining machines. This is because thin-seam operation precludes an onboard operator's compartment or the mine has approval to conduct extended cut mining. Using a tethered or radio-linked control box, the remote operator is typically situated 3 to 15 m (10 to 50 ft) from the working face. The operator receives direct operational cues through senses like vision, hearing and feel. Remote control is sometimes touted as a safety feature. However, this is not always true, as operators are not provided protection from roof and rib falls or being crushed between the machine and a rib. Remote control operators are also left exposed to dust and noise. Teleoperation described here is the computer-based, distant control of mining machinery from a protected operator compartment located out of the line-of-sight from the operational site. Video, sound and other sensory information are gathered through sensors and electronically transmitted to and displayed at the operator's location. The teleoperator responds to the information and makes decisions that are initiated by control devices (usually switches). These control commands are then electronically transmitted to the re¬mote machinery and the appropriate machine function(s) are carried out. Teleoperation increases the safety of mining machine operators as it removes them from the immediate vicinity of hazards. The US Bureau of Mines' involvement with teleoperation dates back to 1979. Following feasibility studies, a highwall milling system (HMS) was developed and tested. A deep, thin-seam, room-and-pillar system (TSRPS) has been designed and is currently being surface tested.

Jan 1, 1992

By J. F. Lupo

Heap and valley leach operations rely on solution collection piping placed within the heap to enhance both solution recovery and to assist overall solution management. The most common piping used in leaching operations is solid or perforated High Density Polyethylene (HDPE) pipe and Corrugated Polyethylene pipe (CPE). These pipes are widely used because of their low cost, ease of installation, durability, and flexibility. The typical recommended maximum design depth of burial for HDPE and CPE pipes is on the order of 30 meters (100 feet). However, ore heap heights at many facilities exceed 30 meters and some are now approaching 180 meters (600 feet) in height. At very high ore heap heights, the stability and performance of HDPE and CPE pipes becomes a critical issue for leaching facility design and operation. Failure of solution collection piping can lead to poor solution recovery, high hydraulic heads on the liner system, and in some cases, unstable ore slopes due to high solution pressures near slopes. This paper presents a review of methods that have traditionally been used to evaluate pipe stability under high normal loads. A common shortcoming of these methods is the inability to account for beneficial effects of ore arching around pipes and the time-dependent creep (stress relief) behavior of polyethylene (PE) materials. A new analytical approach is developed and presented which includes the effects of ore arching around pipes and creep of PE materials. The results of the new approach show that PE pipes will deform under high heap loads, but can remain stable and functional. Pipe stability is shown to be dependent on the type of pipe backfill and initial backfill compaction. The new approach represents a useful tool for designing applications for PE pipe under high normal loads.

Jan 1, 2001

By M. Li, J. D. Miller

Many technology problems must be solved if we are to continue to produce phosphate at our current rate of consumption. The U.S. produces at least 25% of the world's phosphate, 40 million tons of phosphate rock per annum with most of the production coming from Florida. Of particular concern are improved separation efficiency and the ability to treat new dolomitic resources. Phosphate flotation technology needs include: 1. Simplification of the standard flowsheet 2. Improved recovery of coarse phosphate 3. Selective flotation for phosphate recovery from dolomitic resources Preliminary results, including tests on plant feed from Florida show that these objectives may be achieved with a new collector chemistry depending on the specific circumstances. The effectiveness of the new collector chemistry has been demonstrated by the preliminary results from single stage flotation experiments both at the University of Utah laboratories and at Florida Institute of Phosphate Research (FIPR) laboratories. In the best case, from these experiments with low grade (5% P2O5) coarse feed (16x35 mesh), a single stage phosphate recovery of 95 % was achieved with a concentrate grade of 31 % P2O5. Such a separation efficiency could not be achieved using the traditional fatty acid/fuel oil collector. Based on these results it seems that a one step process may be possible for phosphate flotation and a research program is justified for the development of this new flotation strategy.

Jan 1, 2001

By Luzheng Chen

Pulsating high-gradient magnetic separation (PHGMS) of fine hematite from tailings was studied using a pilot PHGMS separator to investigate the possibility of its application in industry. The results of this investigation indicate that PHGMS is effective for recovering fine hematite from the tailings and greatly improved the separation performance compared with the conventional high-gradient magnetic separation at the same conditions. By applying the pilot separator with a 1-mm rod matrix to a tailings containing 28.76% Fe, a concentrate assaying 54.35% Fe with 35.89% recovery was achieved. It was found that the separation performance of the pilot separator closely correlates with the main pulsating parameters, i.e., pulsating stroke and frequency. It was also found that a change in the wire diameter of the rod matrix from 2 to 1 mm causes a weak drop in concentrate grade but results in a considerable rise in recovery. This finding proves that the improved performance achieved by the pilot separator is attributed to the pulsating of slurry and to the use of a 1-mm rod matrix. When the first commercial SLon-2500 PHGMS separator with a 1-mm rod matrix was applied to recover fine hematite from the tailings, the results duplicated those achieved with the pilot PHGMS separator.

Jan 1, 2009

By BHAMIDIPATI S. SASTRY, SRIVATSAN J. SRIDHARAN

Pressure losses in mine ventilation systems are estimated using friction factors and shock loss factors. The efficient planning and designing ofmine ventilation systems depend on the accuracy of the friction factors as well as the shock loss factors that are taken into consideration. While there is a much more acceptable knowledge of what constitutes friction loss in mine roadways, the shock loss factors are in general readily not available for all possible contexts of flow separation phenomena in mines. One such special case of shock loss in mines is the train of mine cars in the airway. Mine cars are widely used for the transportation of material, and the information on shock loss factor for mine cars is limited. This paper examines the pressure loss occurring due to a train of mine cars in an airway using scale model studies and numerical investigations. Computational fluid dynamic (CFD) studies are conducted using four different turbulence models. The performance of different turbulence models is analyzed by comparing it with the experimental results. The study suggests that the boundary layer resolution method is significant in the simulation of shock loss. From the study, it is found that the shock loss factors from presently available model overestimate the pressure loss by 7 to 15 times. A better prediction model for the shock loss factor of a train of mine cars in the airway is proposed using the experimental results.

Jul 24, 2020

By R. C. Burton

One of the major problems encountered with recirculatory breathing apparatus presently used by mine rescue teams is that the inspired air becomes uncomfortably, and often dangerously, hot. This is also true with self-rescuers. It is well known that man can tolerate very high dry-bulb temperatures if the wet-bulb temperature is low, but not vice- versa. The maximum tolerable, wet-bulb temperature is about 42 °C (108 °F). A continuously inhaled wet-bulb temperature above this value can cause irreversible damage to the throat and lung tissue, and wet-bulb temperatures close to it cause extreme discomfort (1) and seriously retard the capability of the man to perform useful work. A theoretical analysis, combined with experimental results, has shown that it is the carbon dioxide absorbent that is the major cause of high wet-bulb temperatures of the inspired air in the Siebe Gorman Proto 4, and in the Draeger BG 174 apparatus, both of which are used by rescue teams on South African mines (2). In the Proto 4 apparatus, the absorbent for the carbon dioxide is soda lime (calcium hydroxide). The German Draeger BG 174 also uses this absorbent but under arduous conditions such as in hot environments (50 °C, 122 °F), the use of an alkali absorbent cartridge is recommended which consists mainly of caustic soda (sodium hydroxide). Lithium hydroxide is used in some apparatus in the United States. It is clear that different absorbents will produce different quantities of heat and moisture for a given rate of absorption of carbon dioxide. The proportion of this heat and moisture which is transferred to the user depends upon how much can be removed from the recirculating air between the absorbent and the mouthpiece. This paper discusses the present methods of heat removal and describes the design and test results of a prototype evaporative cooler.

Jan 1, 1980

Diesel Particulate Matter (DPM) is considered carcinogenic after prolonged exposure. With increasing use of diesel-powered mining equipment in underground mines, miner?s exposure to DPM has been increasing. Most studies on the issue has been DPM control measures with few studies on diesel exhaust propagation patterns after leaving the tailpipes. This study uses computational fluid dynamics (CFD) to investigate the airflow pattern in an underground metal/nonmetal mine for a single heading. Several high DPM concentration areas are identified in the study and common practices for compliance are suggested. Airflow and DPM distribution are compared between blowing and exhausting face ventilation systems. Suggestions are also provided for the protection of miners in the face area.

Jan 1, 2009

By Shenghui Chu, Zhibiao Guo, Dongshan Yang, Yuanxin Zhao, Xiaohui Kuai, Jingwei Gao

The technology of automatically formed roadway without pillars (AFRP) via roof cutting and pressure releasing (RCPR) is a reformatory method for gob-side entry retaining, which automatically creates a roadway by utilizing the fragmenting and expanding properties of rock strata and the mining pressure, to realize a novel technique for coal mining without coal pillars. The Anju Coal Mine is the first kilometer-deep mine where this technology is applied. To conduct a geomechanical model experiment, this research uses the 5307 working face in this mine as its backdrop. The experimental results show that this technology can efficiently decrease the pressure of the AFRP surrounding rock. The roof maximum stress of the AFRP is 21% lower than that of the belt roadway, while the side abutment pressure of the former is 13.4% lower than that of the latter. The comparison of model experiment data and field monitoring data shows that the roof and floor approaching deformations on the roof-cutting side and solid coal side of AFRP differ by 8.8% and 9.6%, respectively. The model experiment results and field monitoring data show good agreement, and the deformation of the AFRP surrounding rock can be successfully managed by this technique. The study’s findings can serve as a guide for using this technology in kilometer-deep coal mines.

Jul 31, 2023

By Reed Thorne

To many people, rescue from elevated, sometimes vertical, locations brings about thoughts of heroism mixed with brawn and self-sacrifice. Images are conjured of cliff rescues where the technical effort is hanging from a few seemingly small nylon ropes hundreds of feet above the ground. Such is the vertical realm of technical rope rescue. This is a technical field in which the author serves professionally as battalion chief of (rope) operations for a northern Arizona fire district, and as a private sector instructor to mines in the United States and Canada.

Jan 1, 1996

By Wm. Ross Wayment, Innes P. Grantmyre

INTRODUCTION It has been recognized for some time that major changes in mining methods will be required in the near future. Two types of factors contribute to this need for change. Intrinsic factors include ground control problems associated with mining at increasing depths, noise, dust, toxic fumes, and logistics problems which arise from operation in a cyclical fashion. Extrinsic factors include competition for labor from industries offering safer and less difficult work, pressure for less impact on the environment, and changing economic and political conditions. The search for new mining methods has resulted in extensive research being carried out on such novel approaches as thermal fragmentation, high-pressure water jets, sonic drilling, microwave fragmentation, and laser cutting, among others. Joy Manufacturing Co. has elected to concentrate on impact breaking in stopes as a first generation continuous hard rock miner. IMPACT BREAKING Fragmentation techniques show a drop in specific energy as efficiency improves. Specific energy is the energy consumed per unit volume of rock removed and is affected by such variables as rock material properties, fragmentation method used, operator skill, tool design, etc. Mechanical fragmentation methods generally have specific energies much lower than that of the more novel methods. Table 1 shows impact breaking to have an efficiency exceeded only by that of drill and blast methods and it is this high efficiency which led Joy to impactors as the subject for research on potential mechanisms for continuous mining in hard rock.

Jan 1, 1976

By K. Whysner

The recycling of metal resources in mining influenced water (MIW) requires a paradigm shift from within the mine water treatment industry. The potential to recover zinc for beneficial use in the micronutrient fertilizer industry was investigated through a survey of zinc micronutrient fertilizer representatives. An application of the findings to a case study of the Argo Tunnel influent MIW was then implemented. It was concluded that the potential to beneficially reuse MIW residuals in fertilizers exists; the current process sequences of treatment will need to be modified if metal recycling is to be prioritized.

Feb 27, 2013

By S. J. Schatzel, J. D. Addis, V. Gangrade, L. L. Chasko, C. A. Hollerich

A ventilation study using tracer gas was conducted at a western US coal mine. The objective of the study was to evaluate the movement of longwall face air exchanges between the face and worked-out area and to document the presence or absence of face airflow pathways between these locations. The mine operator uses a bleederless longwall ventilation system with a back return and a blowing mine ventilation system. The study was conducted on an active panel and included both underground and surface monitoring sites. The study used sulfur hexafluoride (SF6) released as a slug on the longwall face and in the front of the gob inby the face. The velocity of the tracer gas movement in the gob was 0.019 m/s (3.7 fpm). The rate of movement for the overall tracer gas slug averaged about 0.0091 m/s (1.8 fpm). A separate tracer gas test initiated with the release of SF6 into the legs of the first shield showed the existence of more than one pathway of face air in the general direction from the headgate towards the tailgate corner. Maintaining adequate ventilation air on longwall faces is important for worker safety and for the dilution of methane emitted from the face and caved gob. A more detailed characterization of longwall system air and gas movement allows a mine to better assess its ventilation design for controlling gas on the face and in the gob.

By G. A. Calboreanu

One way of cost reduction is attained when using materials with improved erosion ? corrosion resistance. For many years hard irons successfully answered the Mining Operation needs however application ranges were limited due to the low chemical resistance of such alloys. Corrosion resistance of any hard iron increases when microscopically homogenizing chromium and generating passivation conditions throughout and between all metallographic phases. Chromium distribution of the new material called Max10 was analyzed with EDS ? energy dispersive spectroscopy. At critical depleted chromium carbide ? matrix interfaces chromium increased to 31.72% which is well within passivation levels. Generally the corrosion resistance of high chromium hard irons provided by Metal Casting Industry is limited to 0.5% sulfuric acid and 28 PPM ionic chlorides. Such restrains increased when using Max10 to 2.0% sulfuric acid and 100 PPM ionic chlorides. Max10 contains 35% carbide volume fraction, has excellent corrosion resistance within pH = 1.15 ? 13.6 while fracture toughness under plain - strain conditions and Mode I opening is KIC = 20 KSI.(inch)1/2. Wear rate was calculated with the pin-on-disk apparatus using a diamond indenter per ASTM G99 recommendation. After years of research, experimentation and implementation the Max10 castings were service installed in slurry pumps and mixing equipment. In some applications the life time of slurry pumps manufactured in Max10 tripled versus previously used materials.

Jan 1, 2012

By M. J. Lawrence

Independent natural resource Valuers are an essential link between miners and mineral explorers on the one hand and the finance industry on the other. Investors (and regulators) expect the mining and financial industries to be vigilant against the use of inappropriate methodology or use of illogical steps within the chosen valuation method. The Australian Corporations Law generally requires an Independent Expert Report to support mergers and takeovers (as well as for capital raising activities). The introduction of the VALMIN Code (1998) by The Australasian Institute of Mining as Metallurgy, has meant that such Reports, when prepared in compliance with it, are now much more comprehensible and reliable than before. This is because the key requirements of the Code are for transparency and materiality in the Technical Assessment and Valuation Reports prepared in connection with the transaction involved. Transparency is particularly important because it allows the reader to identify and understand the assumptions made to derive a value and to then form a view as to the reasonableness of the result. Even though many elements of resource asset valuation practice are undeniably subjective, there must be some basis of objective rationality to it. Where the reasoning is patently illogical or the inputs are chosen to achieve a particular result, the estimated value must be viewed as virtually worthless. Experience, qualifications, competence and repute are the hallmarks of a professional technical auditor and valuer.

Jan 1, 2000

By R. Unger, L. Mallett

The use of virtual reality (VR) technologies to train miners is an evolving area in research and development. In July 2006, representatives of 14 international organizations met to discuss current VR-related efforts and explore ways to employ VR in the future. This paper gives an overview of the various approaches presented at the meeting and discusses directions for future implementation. An example of a training package that teaches mine map-reading skills is presented. The meeting was the first step to building collaborations for furthering VR applications for mining. Planning has begun for a 2008 meeting open to broader participation.

Jan 1, 2007

Train services through the Channel Tunnel linking Britain and France where scheduled to be fully restored in February 2009 following several months of repairs after a major fire in the tunnel on Sept. 11, 2008. A lorry caught fire on a shuttle train carrying heavy goods vehicles bound for France through the 50-km- (31-mile-) long northern tunnel. The fire, that spread to other vehicles, raged for about 16 hours. The extreme temperatures of up to 1,000º C (1,832° F) caused extensive damage to about 600 m (2,000 ft) of the 7.6-m- (25-ft-) diameter tunnel?s concrete lining, approximately 11 km (7 miles) in from the French entrance. The Channel Tunnel operator, Eurotunnel, awarded the repair con-tract, estimated to be between ?50 to 60 million, to a consortium of Freyssinet, Eurovia Travaux Ferroviaires (ETF) and Vinci Energies. Freyssinet was appointed to look after the civil engineering works, while ETF would be responsible for track and overhead wire restoration and Vinci Energies responsible for other equipment. The technique of hydrodemolition, which uses high-pressure water jets to remove concrete from various structures, was specified as the method to remove the fire damaged concrete. Freyssinet subcontracted the concrete removal to the specialist hydrodemolition and industrial cleaning contractor Philip Lasserat.

Jan 1, 2009

By R. H. Grau

NIOSH’s Pittsburgh Research Laboratory is currently involved in research to identify silica dust generation in underground metal/nonmetal mines. The ultimate goal of this research is to develop control technologies to reduce worker exposure to respirable silica dust. Commodities and job classifications with the highest silica dust exposure have been identified through analysis of the Mine Safety and Health Administration (MSHA) compliance dust sampling database. Dust surveys were conducted in an underground limestone and gold mine to investigate silica dust sources, generation levels, and controls being used. A summary of the mining operations, sampling procedures, resulting data, and suggested methods to improve the dust control will be provided.

Jan 1, 2002