Search Documents

By Gregory E. Tieman

Hydrologic impacts of longwall mining were studied in 1986 after mining had occurred at mine "Z" in northern West Virginia. This mine is 700 to 1,300 ft deep, with a surface topographic relief of 300 to 500 ft. Five springs and one dug well were reportedly dewatered by mining. All such supplies are above nearby streams in elevation, and at least 800 ft above the subsided mine. Three of these six supplies showed partial recovery within one year. Only supplies within 50 ft in elevation of a nearby stream showed apparent partial recovery. Measured perennial streams showed notable depletion in streamflow over mined longwall panels that were less than two years old. Normal stream discharge was measured over panels more than two years old. Most apparent hydrologic dewatering impacts appear to be temporary, and the most vulnerable areas for these impacts are hill sides.

Jan 1, 1986

By N. S. Tanious

The accuracy of vibrating wire stress meters has been questioned by various users in the mining industry. During an in situ coal pillar study, a laboratory evaluation program was developed to determine whether stress meters could produce reliable measurements in coal. More than $0 stress meters were tested for accuracy, repeatability, effects of setting pressure, and the concept of using a single curve for interpreting the stress-meter data. The testing medium was lucite, a material with a modulus of elasticity very similar to coal. The evaluation demonstrated that the stress meters did provide repeatable measurements, but that accuracy was lacking when the recommended interpretation technique was used. Therefore, a new technique was developed that required all stress meters to be calibrated in the laboratory before use in the field. This new technique reduced the average error to typically less than 10% and, in the worst case, to below 15%.

Jan 1, 1988

By B. Tönjes

In the course of the last decade, the concept of sustainability has turned from a catchword into a vision - a vision to which politics and industry feel increasingly committed. In terms of the energy industry, the key criteria for sustainable development are supply security, economic efficiency and social responsibility. Coal is able to meet all these criteria if it is produced in conformity with high safety standards through the use of modern mining technology and converted into electricity with the aid of environmentally friendly methods. Among the fossil energy resources, coal will, according to the vast majority of global energy scenarios, continue to be the most important input energy in power generation for the foreseeable future. Coal is therefore today, and will in future continue to be, an important element in ensuring sustainable energy and raw material supply, worldwide, in Europe and also in Germany.

Jan 1, 2005

By F. N. Kissell

The Bureau of Mines used sulfur hexafluoride (SF6) tracer gas to evaluate the effectiveness of gob ventilation and/or sealing practices at three coal mines, each having different problems associated with their mined-out areas. The purpose of these ventilation studies was to better understand whether current techniques employed for ventilation or sealing are successful at minimizing the potential for gob fires and explosions. The work performed at each mine is discussed: One is a longwall operation that uses ventilation to carry off hazardous gases, and two are room-and-pillar operations, each with far different concerns, that seal off the gobs to isolate them from the main mine ventilation. In all cases, employment of the Bureau's SF6 tracer gas technique resulted in answers to questions raised by the mine operators concerning the effectiveness of their gob ventilation or sealing practices in preventing mine fires.

Jan 1, 1987

By Luís Tavares Ribeiro

Nowadays there is a greater need for detailed reservoir modelling in the oil industry. It is generally recognized that nearly all reservoirs are heterogeneous and idealization of rock characteristics in flow calculations is unrealistic regarding actual physical and textural conditions encountered in geologic formations. The heterogeneity of oil reservoirs considerably influences the distribution of fluids, as well as their displacement. It would be advantageous if a reservoir petroleum engineer was able to construct a precise mathematical model of the detailed reservoir rock variability characterizing the degree of reservoir heterogeneity in an unambiguous way. This paper presents a geomathematical model describing the spatial behaviour and distribution of the principal reservoir properties. The model is based on the Theory of Regionalised Variables and the Kriging technique. The model is performed by a set of computing programs and is tested on an Abu Dhabi oil reservoir in United Arab Emirates.

Jan 1, 1986

By John D. Abbatt, H. B. Newcombe

The Eldorado Epidemiology Project formally began in late 1978. It consists of a retrospective cohort study, to be followed by and to leave in place the mechanism for a prospective cohort monitoring program. These present and future activities are intended to merge into one another. The current study includes all Eldorado employees past and present for whom records are available. The objectives of the undertaking are - 1) to obtain cause-and-effect, dose-response data with which to evaluate the risks to workers in radon and radon daughter containing atmospheres, and to provide additional quantitative information on which to base possible improvements in working conditions; 2) to identify any dead employees of E.N.L. whose cause of death suggests that a potential compensation claim right exists for their survivors, and to similarly identify living ex-employees of E.N.L. whose work histories and states of health suggest potential compensation claim rights. The nature of the study has been determined by the history of Eldorado, which will be described briefly. Eldorado began (as Eldorado Gold Mines) in the late 1920's, operating relatively unsuccessfully in Manitoba. In 1930-31 the emphasis shifted from gold to uranium, and what became the Port Radium mine was first staked. From the very early 1930's until 1942 the company's purpose was almost entirely devoted to the mining of pitchblende - uranium ore - from the Port Radium site, and the extraction of radium from this ore at the Port Hope refinery in Ontario, a process from which the uranium was a largely stockpiled byproduct. In 1942 the company was requested by the Canadian government to accelerate the production of ore, and of uranium. At the same time, all its stockpile of uranium (then being stored in silos as a "waste" product which might later "come in") was acquired for the Manhattan Project. In 1944 the company shares were bought by the Canadian government and the company itself became Eldorado Mining and Refining (1944) Limited; it has operated as a Crown corporation ever since. The name was changed to Eldorado Nuclear Limited in 1968. The Port Radium mine was closed in 1960, and since 1953 the Beaverlodge uranium mine complex has operated on the northern shores of Lake Athabasca. Radium production was discontinued in 1954 when the radium circuit was taken out of the refinery, and since that time the refinery's products have been various types of refined uranium (uranium dioxide, uranium trioxide and uranium hexafluoride) plus metallic uranium. The refinery, of course, processes the company's own yellowcake but as it is one of only five refineries in the western world, most of its work consists of custom refining for a large variety of customers. In addition to the mining and the refining operations, there have been three other divisions involved, and these are, respectively, Aviation, R. & D., and Exploration, in addition to the financial, corporate, administrative and support activities. MATERIAL AND METHODS The human study population (Abbatt, J.D. et al., 1980) consists of all Eldorado employees who have ever worked for E.N.L. and for whom records are available. The total nominal roll to December 31, 1980 is approximately 21,000 and consists of employees of the Mining, Refining, R. & D., Aviation and Exploration Divisions, as well as a relatively small number of other employees (Head Office, etc.). The basic epidemiologic design, as has been mentioned, is for a retrospective cohort study merging into a prospective cohort study, and depending very heavily upon automated record linkage and file matching. The original design called for an initial assembly of the bulk of the nominal roll, prior to the first of two matches with the National Mortality File. The first of these two matches is now complete and the second is to be separated from it in time by 18 months to two years. The second match will be the definitive match prior to the analysis, the interpretation of the data, and the publication of the results. The period between the two matches was designed to permit completion of the nominal roll, including: - addition of previously missing individuals and groups, elimination of duplicates, and amplification of identifying information, - assembly of work histories and exposure information for each individual, - digestion and application of lessons and modifications resulting from the first match with the National Mortality File at Statistics Canada, - preparation of files for the definitive second match. The analysis of data will be carried out by the National Cancer Institute of Canada Epidemiology Unit based at the University of Toronto. This group, with whom Eldorado Nuclear has a memorandum of understanding, have for a variety of reasons, including their familiarity with record linkage and their expertise, been members of the Project Team since

Jan 1, 1981

By J. R. England, W. J. Taylor

The Sudbury Basin is the scene of the mining operations of the Ontario Division of the International Nickel Company of Canada, Limited. Around the rim of the geological formation and within thirty miles of the City of Sudbury are located twelve operating mines and one open pit operated by the Company. The City, with a metropolitan population of some 100,000 lies 240 miles Northwest of Toronto. In addition, there is one mine in Northwestern Ontario, at Shebandowan, 700 miles Northwest of Sudbury. In 1973 these mines produced 16.5 million short tons of ore of which 14.9 million tons were from underground and the balance from open pit operations. Mining methods include blasthole, sublevel caving, induced caving, shrinkage, cut-and-fill and undercut-and-fill. Raise boring commenced at Inco in 1964 and is now applied at all mines in the Sudbury District (Figure 1). [ ]

Jan 1, 1974

By B. (Manas) Das

Rock characterization for geotechnical purposes using the microhardness technique is discussed in this paper. The concept of rock characterization and its steps are logically developed. The geotechnical properties should be functionally tethered to the technological problems for characterization. The overriding geotechnical concern is rock mass stability. The important factors in this respect are rock properties, structural discontinuities, ground water, field stress, temperature and technological factors. The rock properties are the primary factors and the other factors generally affect rock properties. Of the rock properties the strength and elastic properties can form a basis for rock characterization. The microhardness technique can provide these two properties. Study on coal shows that the microhardness impressions can be used for this purpose. On the basis of this study coals of all ranks can be divided into distinct geotechnical groups. The details of these are discussed in this paper.

Jan 1, 1986

By Rodger E. Denison

The Middle Ordovician Simpson Group in the Arbuckle Mountains of southern Oklahoma contains sandstones of unusual purity. These have been exploited as glass sands since 1913 (Ham, 1945). Where quarried, the sandstones are uncemented or weakly cemented, greatly facilitating mining and processing. The origin: sedimentary setting, and lack of cementation of these valuable sands has been the source of much discussion. The lowest of the sandstone units in the Simpson is at the base of the Oil Creek Formation. The basal Oil Creek sandstone is exposed in a series of accessible quarries north of the town of Mill Creek in Johnston County. Virtually all conclusions and generalizations concerning origin of the Simpson sandstones are based upon observations made in these quarries. The three Simpson sandstones overlying the Oil Creek share many of the same distinctive qualities, and there is an assumption that they share a common origin.

Jan 1, 1999

By Frank T. Wheby, Edward M. Cikanek

A computer performs all logic and computations customarily done by hand in preparation of engineers' estimates or contractors' bids on tunnel-shaft systems. The program described is based on construction methods, work forces and equipment selections corresponding to the current state-of-the-art of rock, soft ground and cut-and-cover tunneling. The program contains logic to permit estimates of cost of complicated tunnel-shaft systems; it is not necessary to input quantities, as the program calculates those from the tunnel design that is internally generated. In any estimate, the program bases its cost computation on user-input requirements and site conditions, such as tunnel shape and size, shaft depth, ground characteristics, construction methods, and other factors. To provide great flexibility, the user of the program is provided with options for accepting designs built into the program or overriding these designs by his own inputs. An illustrative example is presented.

Jan 1, 1974

By John A. Shuster, Joseph A. Sopko

Construction of two shafts, as well as associated deep concrete structures, for a major storm sewer project in Milwaukee, Wisconsin required ground water control and temporary ground support to depths ranging from 19.2m to 55.0m. Lowering of the site ground water table eras not possible because of potential consequences for existing nearby structures. Construction entailed completion of two shaft collars into bedrock. In addition to the shafts, several adjacent connected. structures were completed. Ground freezing was selected to provide temporary ground support and ground water control for all excavations. The first application of using reinforced frozen earth was successfully incorporated on the project. The procedure enabled the contractor to create openings in excess of 9.1m in height, without bracing, through highly stressed frozen earth walls. Design features and construction procedures for completion of ground freezing and related excavation are reported.

Jan 1, 1989

By Jim Merza

The recent heightening of environmental issues has forced more and more mining operations to focus on developing new methods to control dust problems encountered at their concentrate dryers, stock piles, tailings ponds and during the loading, transportation and unloading of their products. The development of dust control agents requires a quick reliable and most of all accurate method to evaluate the performance and to optimize the formulation of these products in the laboratory, thus avoiding expensive field trial evaluations. This paper gives an overview of the industry requirements for specialty dust control agents, application techniques and current laboratory evaluation procedures. The paper will also outline the development of a unique dust suppression testing apparatus called the "Dust Box, which is used to evaluate chemical dust suppressants at the laboratory level. Laboratory results from two test programs on different substrates are presented in the paper.

Jan 1, 1994

By K. A. Natarajan, M. K. Yelloji Rao

The effect of galvanic interactions among sulfide minerals such as chalcopyrite, galena, and sphalerite in the presence and absence of a grinding ball material on the flotation recovery of chalcopyrite has been studied. X-ray photoelectron spectroscopy (ESCA) studies were carried out to identify the reaction products on the sulfide minerals after different apes of galvanic interactions. Galvanic contact with active minerals such as galena and sphalerite, either alone or together, significantly affected the floatability of chalcopyrite mineral, such an effect being more severely felt in the additional presence of a grinding medium as well as oxygen. Surface analysis studies revealed the presence of oxyhydroxide species of iron on all the sulfide mineral samples which were in prior contact with the grinding medium. The formation of such oxyhydroxide species of iron was found to be dependant on the relative electrochemical activity of the mineral. Probable electrochemical reaction mechanisms are discussed.

Jan 1, 1990

By Markku Virtanen, Pertti Koivistoinen

From the perspective of a large mining company the comminution circuit design is worth keeping within the boundaries of the organisation. The correct circuit design begins from the understanding of the role of grinding. Grinding is a link only in the long "comminution chain," starting from solid rock and ending at the concentrating stage. The final target in comminution is to take a part in the maximization of Net Smelter Return, which goal provides the simultaneous considering of capital costs, operating costs and the economic effect of process results. As a general rule there will be a single crushing stage only, ahead of the grinding process. Grinding does not use any metallic grinding media at all, and there will be fine crushing for critical material in the grinding circuit. Grinding has a minimum two stages, besides, at many concentrators middling products and quite often also tailings are reground.

Jan 1, 1997

By Robert W. Miller

There are many problems faced by ventilation engineers in deep underground mining operations, not the least of which is controlling miner exposure to radon gas and its daughter products. Radon gas is commonly found in uranium mining operations, but may also be present in other deep metal mines. For example, tin mines in England, iron ore mines in Sweden, gold mines in South Africa, and molybdenum mines in the U. S. have potential radon exposures. This is because uranium and accompanying radium ore are ubiquitous to the earth's crust albeit at low levels. The fact that the activity represented by one WL can be caused by a relatively low concentration of radon gas increases the difficulty of control. Since the source of the radon gas is usually widespread throughout a mine, local exhaust ventilation is not a viable control schema. The technique used to control exposure is then dilution ventilation and, in fact, huge amounts of air must be moved in order to reduce potential exposures to an acceptable level. An interesting comparison can be made of ventilation rates in different types of mines. It is estimated in modern coal mines, which are generally acknowledged to have high rates of ventilation, that about eleven tons of air are moved for each ton of ore mined. A typical operating uranium mine may have ventilation flows of 14-15 tons per ton of ore mined. This provides an idea of the scope and importance of ventilation in modern mining operations where radon is a hazard. Further pressure is put on ventilation engineers by the steady downward trend in exposure limits set by national and international standard setting agencies. Much of this tendency toward lowered standards is based upon longitudinal mortality studies of miner populations. Another important factor is the limited number of experienced miners available in the labor pool. For optimum production, it is important to have as many experienced miners underground in each shift as possible. However, the average daily exposure in a U. S. mine must be less than .3 WL to permit the miner to work underground for a full year. The ventilation system then must provide enough uncontaminated air to maintain the WL below the .3 TTL level to maximize production efficiency and minimize personnel turnover and the problems associated with it. Ultimately, the goal of the ventilation engineer and health physicist is to protect the working miner from harmful exposures based upon currently acceptable standards. U. S. Federal regulations require that in uranium mines all active work sites must be monitored every two weeks if they measure above .1 WL. Areas that have .3 WL ratios or higher must be monitored on a weekly basis until five consecutive weekly samples show the level has dropped below .3 WL. Also, exposure records must be kept for all individuals exposed to levels exceeding .3 WL. These requirements provide a strong economic incentive to have a ventilation system that minimizes exposure of any personnel. A good ventilation system requires careful planning, operation and backup in order to fulfill its mission of providing adequate clean air. Its proper operation also requires coordination with production personnel so it can be adapted as new areas in the mine open up and old areas are sealed off. The ultimate indicator of ventilation efficiency to control radon daughter exposure is, of course, monitoring working levels. Historically, this has been done using the Kusnetz, Tsivoglou, and Rolle's methods, among others. These methods all require cumbersome equipment and tedious calculations to obtain the measurements that results in WL. More important, however, they require a significant time lag between sampling and counting, typically 40-90 minutes. This time lag is, in fact, what can cause significant economic losses due to unnecessary downtime as well as high WL exposures. In a typical mining situation, a sampling technician using the Kusnetz method takes a sample, moves to the next location and takes another sample and so on. Forty to ninety minutes after the first sample, the technician will stop, run the activity count on the filter and calculate the WL. The technician may be one-half mile away or several levels removed from where the first sample was taken when it is counted. If the WL ratio is high the technician must then backtrack to the sample position. There are then two options. If the sample area is a working stage, it can be shut down or a second sample can be taken. If the first alternative is chosen; i.e., shutdown and correction of the ventilation, then another sample must be taken, followed by a forty minute wait for results. If the ventilation adjustment didn't correct the problem, then the whole process must be repeated with a minimum of forty-five minutes per sample cycle when using the Kusnetz method. It has been estimated from operating uranium mines that the cost per hour for downtime on a production slope is about $1,50O/hour. The time lag between sampling and resultant data can be very costly. If the second alternative is chosen to verify the first reading, the miners may be unnecessarily exposed to high levels while waiting for the result. Clearly, such a sampling system can be markedly improved by eliminating the excessive time lag between sampling and analysis.

Jan 1, 1981

By V. R. Voller

The WTBAL computer program for evaluating material balances for minerals processing flowsheets was developed at the MRC and has been in general use for a number of years. This paper reports on two enhancements to the basic MTBAL routine. The original program accounted for errors in the process measurements and used estimates of measurement variability to calculate stream weights. Unfortunately, the estimate of measurement variability was fixed over all streams. In the enhanced version of MATBAL, named IMTBL, the program equations and their solution procedure have been modified to allow the estimated variability in a process measurement to vary from stream to stream. The .second enhancement involves making MTBAL interactive. As such, the user now prescribes his information in an easy-to-use fashion in a conversational mode via a terminal. Finally, an assessment of the feasibility of implementing IMTBL on microcomputer systems will also be reported.

Jan 1, 1982

By J. A. Porter

This paper uses project examples, primarily associated with large iron ore mines in Brazil, to demonstrate opportunities for the mining industry to go beyond traditional compliance and impact mitigation to proactively operate within the ethics of environmental and economic sustainability.

Jan 1, 1994

By Edward DeLilla

Formalized technical audits for mining machinery during manufacturing are a fairly new concept to the North American mining industry. Although used extensively elsewhere, especially in Australia, the concept of independent auditing of machinery design and manufacturing has been slow to gain acceptance in the United States and Canada. Simply stated, a technical audit is an independent, third-party review of all or specific portions of machinery design, manufacturing and assembly to verify compliance with purchase specifications and suitability of the machinery for the specified application. If specified correctly, the useful life of different kinds of structural and mechanical components can be extended beyond normally accepted usage. There is no reason why, if properly designed and built for the application, major structural components on mining machinery cannot be made to last for 20 years before being rebuilt. Also, gearing can be made to routinely last for 15 years.

Jan 1, 1995

By S. Möllerherm

"Since the adoption of the Rio-Declaration in 1992 the concept of sustainable development is raising more and more awareness in public perception. The World Commission on Economic Development WCED has defined sustainable development as the concept that "meets the needs of the present without compromising the ability of the future generations to meet their own needs". The concept requires the integration of economic, environmental and social considerations into all decision making, fostering intra-generational equity through the alleviation of poverty by concentrating the benefits of development in lesser developed areas; and considering the needs of future generations to ensure that inter-generation equity exists. This paper is devoted to give a review of the current status quo of the discussion. It describes the achievements of the mineral industries on their progress towards sustainable development since the Milos Conference (SDIMI 2003), but also discusses future challenges and obstacles."

Jan 1, 2005

By Jan M. Mutmansky

The application of computers and operations research to mine planning problems has changed and progressed significantly over the last several decades with a continuing growth and increased breadth of applications being quite evident. A scan of the volume associated with the 1969 APCOM published two decades ago (Weiss, 1969) indicates that the primary applications in mining were often in the areas of short-term and long-term planning and production scheduling. The applications at that time were oriented toward underground and surface mining, but block and other mine sequencing and scheduling problems for large open pit mines were perhaps the most popular target for the operations research approach. A variety of operations research techniques were used at that time with heuristic models, mathematical programming models and simulation programs all being commonplace. The computers used were usually mainframe models which were of ten shared by accounting, engineering, planning and research groups.

Jan 1, 1989