Search Documents

By C. J. Johnson, C. J. Bise

Abstract - As the US coal industry moves into the next century, it is becoming more apparent that the effective application of new technology is the only way it can remain competitive in the energy marketplace. Examples of this emphasis are with us today in such diverse areas as face- ventilation and excavation-equipment applications. The focus of this new technology is directed toward improvements in health and safety, cost control, and productivity. Room-and-pillar mining accounts for approximately 68% of the nation's underground coal production; this percentage is not expected to decrease markedly in the near future. As such, this paper analyzes the impacts of the changing techno- logical climate on future room-and-pillar operations by comparing a base-case section (current) to three scenarios incorporating new or emerging technology. A microcomputer-based comparative analysis will reflect the changes in section production and costs.

Jan 1, 1990

By Ken Wangerud

The benefits of historic mining to this country have been many, but have come at a cost to the environment that has only begun to be understood over the past twenty years. While estimates vary, it is generally recognized that there are over 200,000 inactive and abandoned hardrock mines, with most of them located in the western U.S. Only a fraction of them are believed to be sources of metal releases with significant adverse environmental effects to the watersheds and receiving streams. State water-quality and natural resource management agencies have noted that hundreds of miles of streams are metal-impacted, and the aggregate effects of these sites within watersheds and drainage basins is poorly understood. Resources for the environmental assessment of abandoned mine land (AML) sites and watersheds have been and continue to be limited. Few hardrock mining states receive substantial reclamation funds under the (coal) Surface Mining Control and Reclamation Act. EPA Region VIII (EPA8) has an estimated 90,000 abandoned mining, milling and smelter sites, mainly in Colorado, Montana, South Dakota, Utah and Wyoming. An estimated 13,000 of the sites may have metal releases causing Clean Water Act and CERCLA non-compliance. Results of inventories by states and federal land managing agencies, indicate it is plausible that only 3,000-4,000 of these sites may be causing significant environmental degradation.

Jan 1, 1999

By S. N. Groudev

Acid mine drainage waters generated in the uranium deposit Curilo, Bulgaria, were treated by means of a pilot-scale passive system consisting of an alkalizing limestone drain, a permeable multibarrier for microbial dissimilatory sulphate reduction, biosorption and chemical neutralization, and a natural wetland, connected in a series. The waters had pH in the range of about 2.5 ? 4.1 and contained radionuclides (uranium, radium), heavy metals (copper, zinc, cadmium, lead, nickel, cobalt, iron, manganese), arsenic and sulphates in concentrations usually much higher than the relevant permissible levels for waters intended for use in the agriculture and/or industry. The water flow rate through the passive system varied in the range of about 5 ? 15 m3/24 h, reflecting water residence times of about 60 to 20 hours. An efficient removal of pollutants was achieved by this system during the different climatic seasons, even during the cold winter days at external air and water temperatures close to 0°C. The removal was connected with different mechanisms but the microbial sulphate reduction played the main role during the warmer months of the year. However, during the cold winter days the removal of pollutants was due mainly to their sorption by the solid dead plant biomass (cow manure, plant compost, straw) present in the multibarrier as well as to their precipitation as a result of chemical neutralization caused by crushed limestone.

Jan 1, 2006

By M. J. Virnig, B. D. Boley, G. A. Wolfe, J. M. W. Mackenzie

A flowsheet for the recovery of nickel and cobalt from laterite ores was developed. The flowsheet involves acid leaching followed by hydroxide precipitation of the metal values and then releaching of the hydroxide cake with ammonia. Investigations of the chemistry of extraction of nickel by LIX® 84-I and a developmental reagent, XI-84-IT, along with the physical properties of the organic phases are described. Based on these investigations, suggestions with regard to design of a solvent-extraction plant and operating conditions were made.

Jan 1, 2002

By Rolf Christiansson, Daniel Johansson, Urban Åkeson, Henrik Ittner, Mats Olsson

"This paper presents two recent studies on the extent of blast damage after excavation in crystalline rock. The Swedish Transport Administration and the Swedish Nuclear Fuel and Waste Management Company (SKB) are both under regulations to limit excavation damage during construction of tunnels. SKB is also required to limit the Excavation Damage Zone (EDZ), as this could be a potential flow path for radionuclides in the planned repository for spent nuclear fuel. Presented in this paper are investigations of blast damage from three tunnel sites, a road tunnel, an experimental tunnel in Äspö Hard Rock Laboratory and an underground subway depot. As expected the fractures resulting from the bottom charge are both longer and more frequent then those mapped in the column charge. The results show that the requirement to limit blast damage according to Swedish regulations was fulfilled for the column charge at the three studied sites.1 INTRODUCTION The Swedish Transport Administration (TRV) and The Swedish Nuclear Fuel and Waste Management Company (SKB) have both recently completed studies related the extent of blast damage from modern explosives after excavation. SKB studies focused on blast damage from pumpable emulsion explosives for underground construction (Ittner and Bouvin 2015) and hydraulic connectivity in the EDZ (Ericsson et al. 2015). TRV had a broader focus with different types of explosives including blasting for both road cuts and tunnelling with pumpable emulsion explosives. Investigations by means of geophysics were also conducted (Olsson et al. 2015). High demands on perimeter control and excavation damage is usually required for underground constructions with a long operation time, such as public tunnels for transport or underground repositories for nuclear waste. This paper presents the findings of recent Swedish studies and aims to discuss the topic in a broader context."

Jan 1, 2016

By M. P. Saunders

A comprehensive, site specific water management plan is of primary importance to the successful implementation, operation and decommissioning of any mining project. Formulation of a plan requires an orderly planning process consisting of identifying problems, establishing planning criteria based on the guidelines and requirements of regulatory agencies, and an iterative procedure of identifying, investigating, and evaluating plan elements and alternative plans. A typical uranium surface mine operation consists of a mine pit or pits, spoil pile areas, crusher, processing plant, and tailings disposal area. A water control plan addresses the problems of diversion of natural runoff from undisturbed areas around the mine; and diversion, collection, and treatment of runoff from within the mine area. A water control plan is required to determine the location and size of appropriate control and detention structures; their cost; and the schedule for permit activity, design, and construction. The plan must be formulated to meet the requirements of both the State and Federal regulatory agencies.

Jan 1, 1981

By A. Halim, A. Martikainen, S. GYAMFI

This paper outlines a unique case of the development of strategies to reduce ventilation and heating costs in Konsuln iron ore mine in northern Sweden. The mine, located just south of Luossavaara-Kiirunavaara Aktiebolag’s Kiruna iron ore mine, was developed as a test mine from 2018-2020 for the Sustainable Underground Mining (SUM) project. Besides functioning as a test mine, Konsuln also contributes to ore production. The existing mine ventilation system was designed for the current production rate of 0.8 million tons per annum (Mtpa). There is a plan to increase this rate to between 1.8 and 2.0 Mtpa.

Dec 23, 2021

By W. L. Fourney, D. C. Holloway, J. W. Dally

Introduction Improvements in the process of rock excavation by blasting involves better control of one or more phases of the fracture process immediately after detonating the ex- plosive charge. Total control of the process involves individual control of (1) The number of fracture planes. (2) The crack initiation sites. (3) The direction of crack propagation (usually radial). (4) The stress field driving the fracture front. Fracture plane control is usually accomplished today by using the smooth wall blasting method; however, investigations by the authors (1) indicate several areas where this method could be improved. These improvements include: a) generation of stress concentration factors at the location of the initiation sites; b) protection of the remaining region of the borehole wall to inhibit initiation of any cracks not associated with the fracture plane and fragmentation pattern; c) limit peak detonation pressures to avoid borehole crushing and maintain by stemming residual gas pressure in the bore- hole during the crack propagation period. This paper describes experiments con- ducted with a charge holding device fabricated from thin-wall steel tubing which was partially slit at fracture locations. The tube lined the bore-hole in laboratory tests to simulate smooth wall blasting. Results showed close control could be achieved relative to both the number and the location of the fracture initiation sites.

Jan 1, 1977

By Christopher Newman, Andrew Minckley

With underground stone operations developing in deeper and more geologically complex conditions, accurate pillar stability analysis becomes for the evaluation of engineering design. This paper provides engineering-based recommendations for applying LaModel to evaluate multiple-level room-and-pillar stone mines in both shallow and deep cover. It provides practical guidance on model calibration using field observations, selection of input parameters, and interpretation of results to inform design and operational decisions. The analysis demonstrates LaModel’s effectiveness in simulating pillar load transfer, stress redistribution, and failure mechanisms in complex mining geometries where empirical methods may be inadequate.

Feb 22, 2026

By Heinz Hofmann

In order to drive tunnels with low overburden in town regions, it is necessary to give a quantitative prognosis for the deformation of the underground as well as of the tunnel-lining and of its stability. These problems and their solutions are illustrated by the works for a two-track-railway-tunnel in Bochum (Ruhrdistrict). In this case the most important problems consisted in passing below buildings in a vertical distance to the fundamentals of only 3.20 m and a railway earthdam with rapid train traffic in a distance of 4 m under the dam. The results of measurements from other comparable tunnels and finite-element-computations were used to prognose the settlements on the surface and in the ground, their distributions and their development in time. To obtain these values at the site, a special system of tunnel driving was executed. The tunnel was excavated with the newest type of tunneling-machine from DEMAG, cutting an inclined front, immediately followed by a special temporary support of shotcrete and inclined steel-ribs. By using theoretical and empirical methods to assess the behavior of the tunnel and underground and by executing an optimal driving system in technical as well as economical aspects, the expected behavior, expressed in quantitative values, was almost equivalent to those received by control measurements.

Jan 1, 1974

By Walter Hoecker

The dissolution of gold in cyanide_ leaching has been we11 published with the genera1 acceptance that gold is oxidised by oxygen and stabilized by complexation with cyanide [1]. The dissolution of gold is essentially an electrochemical process. The rate of the anodic gold dissolution is controlled by the cyanide concentration. - (2) While the cathode reduction of oxygen is controlled by dissolved oxygen concentration - (3) There are a number of factors influencing the concentration of oxygen, and if 1owered substanth.lly will effect the efficiency of the leaching plant. These include: "' salinity "' temperature "'partial pressure "'oxygen consumption rate The use of pure oxygen for· cyanidation is only beneficial if oxygen is rate limiting, Conversely a slurry saturated with air (typically 5 - 8 ppm) may not be enough for maximum leach rate. The diagram below shows the maximum dissolved oxygen levels obtainable with pure oxygen and air. DISSOLVED OXYGEN (MAXIMUM) IN WATER At steady state, the rate of the cathodic reaction must equal the rate of the anodic reaction. Thus the rate of gold dissolution is dependent on both the· cyanide and oxygen concentrations. - (4) Using an average of Do/Den =· 1.5 [2] (where Do and Den are the oxygen and cyanide diffusion coefficients) the table below illustrates the maximum effective oxygen concentrations for given cyanide levels in clean water [3].

Jan 1, 1992

By Barry A. Hillman

The rapid evolution of computer and field sensor technology is now providing the ability to integrate mine and office opera­tions. Digital maps and mine plans as well as CAD and GIS can be transferred to ruggcdized field computers for development of real-time mine surveys and real-time GPS machine navigation and monitoring. Surveyors can insure that their surveys arc accu­rate before returning to the office. Engineers and surveyors are also able to upload field computer-based surveys to mine plan­ning software and directly to mine equipment including shovels, drills, and dozers providing the operator of the equipment with a real-time view of their work space. Production information can be transmitted through dispatch and/or centralized mine servers to update mine plans with mining progress and production data. Static mine models then become a dynamic element of opera­tions, providing greater use of information that emphasizes the spatial aspects of the mine by providing real-time maps, produc­tivity charts, and graphs. This information can be disseminated through various mine communication systems to provide opera­tors and management with real-time feedback as well as daily and weekly reports. Integrated systems now being used in exten­sive trials arc reporting productivity increases of 4 - 7% or more thereby providing rapid payback to the mine.

Jan 1, 1998

By S. Healey, P. Jean, G. Deschenes, M. Fulton

Three years ago, the New Britannia Mine started a project to improve productivity of its cyanidation plant. Results indicated that gold dissolution was strongly influenced by sulphide minerals and that the slower gold dissolution rate had a detrimental effect on overall gold recovery. The leaching strategy had to be modified to address this issue. Changes to the leaching circuit proved to be very successful. The first action was to introduce lead nitrate in the leaching circuit. The strategy of addition of lead nitrate was upgraded in three steps. An on-line free cyanide analyser was installed and the strategy of cyanide addition automated. The enhancement of the leaching kinetics have resulted: an 4% increase of gold recovery, from 87.8% in 1996 to 91.9% in 1999, which represents a reduction of 0.17 git Au in the leach residue; an average of 1330 additional extracted gold ounces per year from 1997 to 1999; a 21 % reduction in the cyanide consumption; the shut down of the cyanide destruction plant; and finally a contribution to the 27% reduction in the overall production cost per tonne of ore.($ 3 per ton). The significant increase of the throughput was instrumental in the reduction of the processing cost. In 1999, the improvement of gold recovery represented an additional gross revenue of $c""l.9 Million. The project is discussed in details in this paper.

Jan 1, 2000

By A. Iordanidis

Ieropigi Fe-Ni deposit is located in northern Greece, in Kastoria?s prefecture near Albania?s borders. A laterite profile exposed by opencast mining and placed near the basement of the mine was chosen for sampling. Ten samples, representing ?pure? Fe-Ni ore, ophiolite-bedrock, ?red? ophiolite and ?enriched? ophiolite were collected, based on macroscopic observation. The samples were analysed by X-Ray powder Diffraction (XRD) for the determination of the mineral phases. Iron and Nickel concentrations of the same samples were also determined by X-Ray Fluorescence (XRF) methodology. The Fe-Ni ore samples consists predomi-nantly of hematite, goethite, chrysotile (serpentine), saponite and quartz. ?Red? ophiolite samples consists mainly of chrysotile, hematite, quartz, calcite and small amounts of paragonite and goethite. Bedrock and ?enriched ophiolite samples are comprised of chrysotile, hematite, calcite, quartz, nontronite, paragonite and sepiolite. The Fe content ranges between 13% and 49% in Fe-Ni ore samples and between 7% and 10% in ophiolite samples. The Ni content ranges between 1% and 3% in Fe-Ni ore samples and between 0.3% and 4.5% in ophiolite samples (the higher content is observed in the so-called ?enriched? ophiolite). A correlation between Fe-Ni concentrations and mineral assemblages is being attempted in order to evaluate the nickel-rich mineral phases. It is shown that the nickeliferous minerals are serpentine, hematite, goethite and saponite.

Jan 1, 2006

By Robert A. Jankowski, Jonathan Kelly, Edward F. Divers

Results for the first underground test of the ventilated drum in a U.S. coal mine are presented. Tests were conducted by the Bureau of Mines through a contract research program with Foster-Miller, Inc., to evaluate dust control effectiveness in a western mine and for gas control in a full scale laboratory facility. The ventilated drum is designed to reduce the amount of dust from cutting by drawing dust-laden air from the cutting zone through twelve water- powered "dust capture" tubes built into the shell of the shearer drum. High pressure water up to 1 12.48 kg per cm2 (1,600 psig), released from sprays, induces maximum airflow of 1.89 m3/sec (4,000 cfm) from the face side of the drum and provides cleaning for respirable dust and improved methane dispersion. At the gob side of the drum a deflector plate, attached to the cowl arm, turns the water spray and a proportion of the cleaned air back into the cutting zone. More than 50 ventilated drums have been installed to date in England, and their tests carried out on fixed height and single-ended ranging drum shearers have shown reductions in respirable dust of 60-80 pct, as compared with conventional wet cutting. The U.S. test on a double drum shearer showed slightly lower reduction.

Jan 1, 1987

By R. Gilliam

The Jewett Mine is located in two East Central Texas Counties, Leon County and Freestone County. The area is primarily suited for agriculture with approximately 90% of its agricultural income coming from beef cattle and hogs. In addition to livestock both of these counties produce hay, oats for grazing, pecans and corn. There are 1,101 farms and/or ranches in Freestone County consisting of 381,248 acres. Less than 15% of this acreage is harvested croplands. Leon County has 1,227 farms and/or ranches for a total of 442,387 acres, of which less than 13% is harvested cropland. Total annual agricultural sales for Leon County are approximately $36 million and Freestone County has approximately $21 million. Ninety percent of the annual agricultural sales derive from livestock.

Jan 1, 1992

By V. Svalbonas

With the occurrences of serious mill structural failures on both ball and primary mills, the mining industry has entered the era of detailed fabrication specifications. Such specifications, however, have been developed as individual entities, often by people not related to the mill design function. Therefore, there has been no effort to relate mill failure or safety to the existence or elimination of specific fabrication flaws; that is, no cause-effect failure relationships have been developed. The omission of this step produces a specification which can be termed uneconomical at best. The present paper attempts to fill this void, by reviewing methods for design consideration of flawed structures, and describing experimental tests used to tie such data to a meaningful quality assurance program in fabrication.

Jan 1, 1985

By A. F. Stewart

Slope design in an open pit mine includes the determination of a number of parameters, including bench height, bench face angle and berm width. By way of a case history of two highwall slopes (160m and 220m high) excavated in dipping strata in an operating coal mine, this paper illustrates the influence that bench face angle can have on the stability of an entire slope. The two highwall slopes, the lower of which experienced significant instability, were excavated in essentially the same lithologic and structural environment, with the main differences between the slopes being the angle at which the bench faces were excavated and the excavating methods that were employed. In addition to describing the instability that occurred on one of the pit walls, relevant aspects of the engineering geology, slope design and excavation procedures are described.

Jan 1, 1998

By Gareth Mainwaring

The Cross Harbor Freight Movement Project is currently in the Environmental Impact Statement phase. The scheme is addressing alternative solutions to transport freight across the Upper Bay of New York Harbor, from New Jersey through to Brooklyn, Queens and Long Island. Amongst the alternatives being assessed are two tunnel options; from the north shore of Staten Island through to Brooklyn, and from Jersey City to Brooklyn. These tunnels are approximately 30,000 feet in length, and with up to17,000 feet under the Harbor, would make it one of the longest undersea crossings in the world.. The paper addresses the development of the project, from the Major Investment Study through to the current EIS, and describes the tunnel schemes that are being taken forward. The geological conditions that will be encountered, proposed construction methods, and the ventilation issues associated with such major undersea tunnels will all be described.

Jan 1, 2003

By B. K. Mishra, R. K. Rajamani

Discrete element is a numerical technique for describing the collision dynamics and motion of an assembly of particles. In particular, calculations are done on full three-dimensional space with a force-contact law for collisions and Newton’s law for subsequent motion. It may be said that there is no empiricism in this approach. The paper describes the full scale simulation of large diameter semiautogenous grinding mill of size 40X24 ft. It is shown that the simulation predicts the power draft of plant size mill extremely accurately. Also these simulations have been adapted uniquely to assess the motion of pebbles and slurry in pulp lifters. The passage of slurry from pulp lifters into trunnion is extremely important since flow-back and carryover must be avoided at all cost. The dynamics of slurry flow through pulp lifters is also described in this paper.

Jan 1, 2003