Search Documents

By S. Rupprecht

"INTRODUCTION This paper addresses the prevalence of poor public reporting practices of Coal Exploration Results, Coal Resources and Coal Reserves in southern Africa. Currently, the reporting of coal tonnage without supporting coal qualities or “saleable” tonnes and quality is a poor reporting practice that occurs far too often. Not all coal is equal – therefore it is extremely important that investors or potential investors are provided with the full details of both run-of-mine (“ROM”) and Saleable coal tonnage, their associated qualities and other material and relevant information. Competent or Qualified Persons should note that publicly reported information should be sufficient to enable an informed reader to make a reasonable and balanced assessment of the significance of the information provide. “Companies are encouraged to provide information in their Public Reports, which is as comprehensive as possible” (CRIRSCO, 2013): too often this isn’t the case and material matters are either not reported or inadequately disclosed. According to the South African National Standard (SANS) 10320:2014 draft document - “tonnage and coal quality that will be available for sale, either in the raw ROM state (raw Saleable) at a specified moisture content, or after beneficiation of the ROM coal by processing operations to produce materials at specified qualities, size ranges and moisture contents. The assessments must demonstrate that at the time of reporting, the marketing of the products is reasonably justified. The basis of the predicted practical product yield to achieve the Saleable Coal Reserve must be stated. The moisture basis of reporting shall be stated.” As an example to why coal qualities are so important to the public, the requirements of South Africa’s electric public utility (Eskom) power stations are highlighted. The Kendal power station, commissioned in 1988, operates at a Calorific Value (“CV”) range of 19 to 20MJ/kg, an Ash content between 29 and 34% and Volatiles between 20 to 21%. Other power stations, such as Kriel or Hendrina, may require different qualities such as a CV range of 22 to 23MJ/kg, an Ash content between 20 and 28% and Volatiles between 22 to 23%. Thus, in terms of domestic saleable coal, it isn’t just about reporting the coal qualities but also informing the investor as to which power station the coal is intended to be sold as “boilers are designed to burn particular qualities of coal” and “it is not always possible to transfer coal between stations because of different quality requirements at each station” (Chetty, 2010). Sulphur content is also another important quality with the ideal coal content having a quality of less than 1% Sulphur."

Jan 1, 2018

? World industrialization, increased urbanization, and population growth are driving a sustained demand for minerals, metals and coal. Energy demand is expected to increase significantly in the coming decades - placing even more emphasis on supply, security and environmental impact issues. ? Several countries are taking steps to nationalize their own resources thus safeguarding their supplies and reducing exports of natural resources. ? Understanding the future availability of critical minerals requires a global perspective. It is essential to know where deposits are located, their reserves and resources, the technologies necessary for production, and the costs of producing and transporting the products to consumers. ? As mining companies look to maintain or increase their operating capabilities and increase their mineral resource bases, the search for commodities expands beyond developed terrestrial regions of the world, to include marine resources. (Figure 1) Operating challenges in these locations include finding skilled workers, building infrastructure, improving recovery technologies and practicing sustainable development.

Jan 1, 2011

By R. Hogg

Sedimentation in highly flocculated suspensions of fine particles such as clays occurs through individual settling units (flocs) which have very open structures and correspondingly low density -typically less than 5% solids by volume. It follows that such settling processes rapidly lead to the build-up of a bed of flocs which are essentially close-packed, with inter-floc porosity of perhaps 50%, but with an overall solids content of no more than about 2-3 percent by volume. An important consequence is that the thickening process is dominated by the consolidation of this bed rather than by simple settling of the individual flocs. Experimental measurements of sediment consolidation in flocculated clay suspensions indicate that for a given system, consolidation rates are essentially determined by solids concentration and can be evaluated using the classical Kynch treatment. However, these rates are strongly dependent on the physical as well as chemical conditions of the flocculation process. Furthermore the extent to which gravity consolidation proceeds depends on the total weight of sediment (i.e. on both height and solids concentration). The implications with respect to thickener operation and the requirements for laboratory testing for thickener design are discussed.

Jan 1, 1992

By John W. Welty

Volcanic activity occurred during six periods of Arizona's geologic history. Precambrian volcanism occurred in two pulses at 1.8-1.6 billion years (b.y.) ago and at 1.2-1.1 b.y. ago. Volcanism occurred again in mid-Jurassic and Laramide (Late Cretaceousearly Tertiary) time. Volcanic rocks from these times are not used commercially in any significant quantity. Middle and late Cenozoic magmatic activity covered large areas of Arizona with voluminous volcanic rocks. During the mid-Tertiary magmatic pulse, explosive silicic magmatism, with eruption of areally extensive ash-flow tufts, covered large areas in the Basin and Range Province, while the Colorado Plateau remained largely unaffected. Basalt eruption also occurred during and immediately after silicic volcanism, leading to compositionally diverse suites of volcanic rocks. Late Cenozoic volcanism occurred throughout Arizona and was dominated by wide-spread eruption of basalt flows with local cinder-cone clusters and siliceous volcanic deposits. Perlite deposits near Picketpost Mountain in northeastern Pinal County account for the bulk of the industrial uses of mid-Cenozoic volcanic rocks. Other perlites of presumed middle Tertiary age are present in central, southeastern, and western Arizona, but to date remain unexploited. Arizona Fire Agate is a valuable gem material and is associated with volcanic rocks of middle Tertiary age. Basaltic rock of this age also is utilized in the manufacture of rock wool for insulation. Late Cenozoic volcanism produced most of the industrial-quality volcanic rocks. Basalt, cinder cones, and materials of rhyolitic composition are commercially exploited by municipal and Federal agencies and private industry for aggregates, road conditioners and maintenance materials, asphaltic concretes, cinder block construction, pozzolans, and landscaping. These deposits are generally confined to the Flagstaff and Springerville areas. A famous peridot gem locality is associated with late Tertiary basalts at Peridot Mesa on the San Carlos Indian Reservation. Important products derived from altered volcanic materials of late Cenozoic age include clay and zeolite. Arizona's volcanic-rock sequences are still incompletely known, particularly in central and western Arizona. The potential for recognition and exploitation of important new deposits of useful volcanic materials is high.

Jan 1, 1987

By D. F. Cater

The Macassa Mine is a mature mine with a 61 year history of continuous production. The majority of past production has been derived from a zone called the '04 Break (Main Break). Recent underground mine exploration has been successful in locating several neighbouring ninera1ized zones. This paper will characterize the spatial location, geometry and mineralogical properties of these secondary zones. Future plans for underground mine exploration to follow-up on these target zones will be outlined.

Jan 1, 1995

By A. Dale Wunderlich

With the price of precious metals at an 18-year low, every ounce of metal produced is important. The theft of metals from mining and refining sites can mean the diffrence between profit and loss for many mining companies. Low metal prices do not reduce the potential for the theft of precious metals. History has shown that the price of gold has little to do with the desire for employees to steal precious or base metals. There is actually evidence that the theft of precious metals increases when the price of this commodity goes down. Several of the major precious metal thefts in the past year took place at silver mines when the price of silver was less than 16 cents/g ($5/oz). How does the lowest gold price in 18 years affect the need for security at precious metals properties? There is no short answer to this question. One reason is because the exposure to theft of precious metals is unique to each property. This makes it important that each property be evaluated individually. More than 95% of all precious metals thefts can be attributed to those working at the mine site. So preventing employee theft is the primary concern. One consideration is the location of the property. Gold selling at any price is still an attractive commodity in countries where the employees are making between US$400 and US$600 a month. It is not uncommon for employees at mines in countries where low wages are the norm to consider the value of a gram or two of gold to be a significant amount of money. A gram or two of gold a day may not seem like much. But if 15 employees steal two grams a day, that equates to a significant amount of money during a year. The type of property where the precious metals product is being recovered is also important. For example, a property with a gravity circuit is more likely to suffer from the theft of gold product than a property where all gold is finely disseminated and the only gold seen in the ore body is through a microscope. Gravity circuits increase an operation's exposure to theft because the grinding circuit that is associated with a gravity circuit often becomes a giant concentrator. Areas such as the bottom of grinding-mill pump boxes, cyclone-feed-pump clean out traps and the sumps often become locations where precious metals concentrate (Figs. 1 and 2). Muck concentrations in these locations can be as high as 25% to 40% of gold or silver. Not long ago, muck was removed from a barren-solution sump at a Merrill Crowe circuit that had concentrated to more than 40% gold. At a milling site in the Pacific Rim, residents of the community adjacent to the mine learned about the value of the concentrates in the sump under the ball mill and committed an armed rob¬bery. While several of their co-conspirators held the em¬ployees at bay with machetes, the others emptied the contents of the sump into buckets and removed it from the site. Armed robbery is not as common as employee theft. However, while this article was being written, an armed robbery occurred at a gold property in Central America. Armed perpetrators took as hostages the night shift employees at a process plant and used cutting torches that were on site to cut into the high-security and gold-storage areas. The perpetrators then stole a company vehicle to remove the stolen gold buttons and sludge from the site. Unfortunately, this type of activity goes on regularly. But managements of most mining companies are reluctant to discuss theft scenarios. So information pertaining to the theft of precious metals seldom becomes a newsworthy item. An audit conducted at a mine site with a gravity circuit recommended that the gravity recovery area be shut down until adequate protection could be provided. Although it was not connected with the audit, it was necessary to shut down the gravity area for a pro¬longed period because of problems with the gravity table. In the two months that followed, gold production at the site increased by about 31 kg/month (1,000 oz/month). It is difficult to attribute all of this increase to the theft of concentrates. But there was a good chance that at least part of the increase was due to the fact that concentrates were being stolen from the gravity area.

Jan 1, 1998

By J. Singh

Recently, a Maryland bank became the overnight owner of a toxic waste site through a foreclosure. The original property owners had operated a crash and garbage business on the site and obtained loans for their business venture through the bank. In 1980, their son purchased the property from his parents with mortgage monies obtained from the bank. Failing to make his loan payments, the son defaulted on the mortgage. The bank foreclosed on the property and eventually purchased the property at a foreclosure sale. Shortly after the bank's purchase of the site, toxic wastes were found on the property--the result of disposing solid wastes on the site for 10 years. The bank declined responsibility for contaminating the site and consequently for its cleanup. The Environmental Protection Agency (EPA) took corrective actions to clean up the site. EPA then handed the bill to the bank, citing the Comprehensive Environmental Response Compensation and Liability Act (CERCLA) of 1980 (more commonly known as "Superfund"). CERCLA imposes liability on the current owners and operators of hazardous waste sites.

Jan 1, 1988

By S. Chander

The formation of surface films on pyrite has been studied through electrochemical techniques of cyclic voltametry and AC impedance measurements. The characteristics of the surface films depend upon the conditions of oxidation and the source of pyrite. At potentials near 0.0 V, some pyrites have large values of polarization resistance showing a certain degree of passivity. Some pyrites show more passivation than the others, however. On oxidation, metastable phases of Fe(OH2) and Fe(OH3) form which transform to more stable 3 phases on aging. The growth of surface films near the corrosion potential of pyrite follows a linear kinetics which is attributed to a chemical (or an electrochemical) reaction as the rate determining step. The surface film is considered to be a hydroxide or an oxide rather than sulfur because the later is expected to be limited to a monolayer in alkaline solutions. This study has also demonstrated that AC impedance measurements can be used to study the growth characteristics of films at mineral/ solution interfaces.

Jan 1, 1987

By Stephen Krickovic

"Bleeding", as used in mine ventilation language, has a number of meanings among mining men and is regarded with different degrees of importance. This lack of uniformity stems from a number of specific situations. A method that is adequate in a mildly gaseous mine may fall short in a very gaseous mine. Projected bleeders could be dependable under a certain type of roof, and totally unsatisfactory under a different type. Similarly a plan of bleeders can be rendered useless due to undulations of seam and water in one mine and function well in another. Finally, what is effective in a mining system with partial recovery will not suffice with full recovery. You may wonder, then, if there is a common denominator for the essential function of "bleeding". In my opinion, there is, and it can be defined as controlled movement of air across an active pillar line toward the back and outby ends of the adjacent gob area into the headings provided for the purpose. The objective is to maintain as methane-free as practicable a belt adjacent to the working places, so that, if face ventilation is interrupted temporarily, the gas will not accumulate in dangerous volumes at the working faces before ventilation is restored. It's possible for these temporary interruptions to be unnoticed in time or at all. In such cases, ineffective bleeding could cause a disaster. This has happened. To control, there must be power. That is to say, there must be adequate air, pressure differential between the front and back ends of a pillar line to facilitate proper regulation for diverting of air to the various portions of the gob and as far away from the active section as is practicable. As an indication of the importance of pressure, it is noteworthy that one may provide and maintain in a reasonably open condition a heading or two for a bleeder system and fail to obtain effective bleeding .because air pressure differential is inadequate. On the other hand, you are all familiar with the fact that pillar lines in some seams can be ventilated adequately by air flow straight across the gob when the section is near a main return shaft and thus obtains a heavy pressure differential.

Jan 1, 1962

By Y. Guan

The dissolution behavior of silver and copper from silver/copper alloys in ammoniacal solutions has been investigated using a rotating disc. Oxygen was used as an oxidant. The effect of composition of alloys, concentration of lixiviants, stirring speed and temperature on the overall dissolution kinetics has been studied. Silver / copper alloys of three compositions were used in this study. The atomic percents of silver in these alloys were 76.9, 46.9 and 24.1. The results on the rate of dissolution obtained for these alloys have been compared with that of pure silver and copper under the same testing conditions. A particular emphasis has been given to the galvanic effect on the overall dissolution rates.

Jan 1, 1993

By Kousik Sinha

The advantage of using a clean coal as a feedstock in a direct liquefaction plant is improved performance of the plant by several factors e.g., increased throughput of coal; reduced wear and tear of valves, pipes, and pumps; increased liquid yields, etc. This paper examines the technical feasibility for cleaning Illinois #6 coal as a feedstock to a direct coal liquefaction plant via selective agglomeration using a coal-derived heavy distillate, Wilsonville V-1074 as agglomerant. Effects of addition of Kerosene or coal-derived Naphtha as conditioner, coal particle size, slurry pH, oil to coal ratio, and operating temperature on ash reduction and clean coal weight recovery have been studied. Results show that about 70% of the ash can be removed from this coal and the clean coal weight recovery over 85% can be achieved by using this technique with suitable selection of coal particle size, slurry pH, mixing intensity and oil to coal ratio.

Jan 1, 1991

By S. K. Kawatra

Although temperature is known to have a substantial effect on many processes, this parameter has been widely dismissed as insignificant for mineral comminution. For this reason, temperature effects on grinding have largely escaped notice. However, it has been observed that processing plants which are subjected to large seasonal temperature variations show a change in performance which appears to be due to changing feed temperatures. The general effect is an increase of the specific energy consumption as the temperature decreases. In autogenous mills, an increased rate of production of critical-size material has also been observed. This is due, at least in part, to changing rheological conditions in the mill, with the slurry viscosity increasing markedly at low temperatures. Mechanical changes in the rock with temperature, such as increased brittle fracture, is also responsible for a portion of the observed seasonal effect, and may account for this phenomenon being observed only in certain plants.

Jan 1, 1989

By E. D. Goddard

There are similarities, and differences, in the surfactants used in cosmetics and detergents. In both applications anionic surfactants constitute the major category. Their main function is to clean, i.e. remove grease and particulate matter from fibrous or hard surface substrates. Cationic surfactants are used for conditioning substrates. Nonionic surfactants can function as a substrate cleanser but are seldom used as such in cosmetics; however, selected non-ionics are often employed as a primary emulsifier. Several specialized nonionic surfactants are used as a secondary surfactant in formulations to promote foaming and emulsification. Specific examples and modes of action of surfactants will be presented.

Jan 1, 1988

By J. Bacho

The modern drilling fluids industry is a dynamic, evolutionary environment. It is continuously striving to satisfy and anticipate the ever-changing needs of the oil and gas industry. The predominant driving forces in the industry over the past decade have changed dramatically. Health and environmental issues, coupled with economic and performance requirements, demand innovation and change from the drilling fluids industry. Emerging drilling fluid technologies will demand environmental considerations from mined components with additional emphasis on cost and performance criteria. Drilling fluids providers continue to search for and identify environmentally sensitive components which meet or exceed the performance of their more toxic predecessors. These changes have and will impact the components of drilling fluids that are mined.

Jan 1, 1994

By Thomas L. Kesler

Lithium raw materials usable with present technology consist of pegmatite ore and surficial evaporite brine. Those advantageously located now supply world markets. Materials of similar grades and magnitude, but less favorably located, will come into production as present sources are depleted and markets expand. Some of these potential supplies have been explored, and are reserves in the sense of known availability and quality. Reserves herein are of two classes, those proved by close drilling and assaying, and those of only probable status because their scale and grade are unsystematically indicated. Possible resources include similar materials whose bulk can only be inferred on indirect evidence. All figures apply to total materials in the ground. No allowance is made for losses in mining, evaporation, beneficiation, or chemical processing.

Jan 1, 1977

By Aurel Goodwin

MSHA is the regulatory Agency which administers the Federal Mine Safety and Health Act. Although MSHA's principles largely derive from this Act, they do not exculsively derive from it. One might expect that our principles are contained in the regulations we have published to implement the Act. To a degree, this is true; but the regulations we have now were developed and published before the current Act became effective. For this reason, as well as others, there are some principles that we support which are not evident in our regulations, or in the Act. One of these is the ALARA principle. This principle requires that all unnecessary exposure be avoided; that is, all exposures should be kept "As Low As Reasonably Achievable." Almost all professionals in radiation control can agree with this broad principle; but it would be difficult to get agreement on a regulation which would translate the principle into industry practice. Rather, our regulations specify a limit to exposure for any individual. For radon daughters the current limit is four working level months per year. By having an explicit limit such as this, the ALARA principle often becomes lost and the limit becomes the goal. The principles contained in the Act are equally broad in scope. The principles apply not only for radiation protection, but also for toxic substances and harmful physical agents. The Act states that standards for such substances or agents shall most adequately assure on the basis of the best available evidence that no miner will suffer material impairment of health or functional capacity, even if such miner has regular exposure to the hazards dealt with for the period of his working life. The Act also provides that, although protection of health must be our foremost concern, other considerations shall be the latest scientific data in the field and the feasibility of the standards. Our regulations reflected similar principles when they were developed and promulgated. From experience with other health and safety laws, Congress realized that setting and meeting an exposure limit may not be sufficient to prevent disease. The Act, therefore, contains a detailed description of additional provisions to be included, where appropriate, in mandatory safety and health standards. One of these additional provisions requires that miners be informed about the nature of the hazards associated with their job and about the means for their own protection. Another provision requires the use of labels and other forms of warning to inform miners about the hazards, about proper precautions for safe use or exposure, about relevant symptoms of overexposure, and about emergency treatment. We have partially implemented these provisions through regulation. The Act requires also that standards shall prescribe protective equipment and control of technological procedures and that they shall provide for the monitoring of miners' exposures. We have implemented this provision to a degree also through regulation. Finally, the Act specifies that, where appropriate, a mandatory standard must prescribe the type and frequency of medical examinations in order to most effectively determine whether the health of miners is adversely affected by exposure. Additionally, when a determination is made that a miner may suffer material impairment of health or functional capacity by reason of exposure, that miner must be removed from such exposure and reassigned. In order to encourage miners to take the medical examination, the Act also provides that the miner shall not suffer loss of pay as a result of being reassigned. This additional provision on medical examinations has not been implemented by regulation for radiation hazards, nor for most other toxic substances or hazardous physical agents. We believe that this conference will provide us with valuable information on medical examinations for radiation exposure, as well as on other considerations to be used in future regulations. We still question whether our basic exposure standard of four working level months per year is adequate to protect a miner's health. This conference is indeed timely because both MSHA and NIOSH have been reviewing this issue for some time. I would like to reemphasize MSHA's commitment to education and training. MSHA strongly believes that miners should be informed fully about the real and potential hazards associated with their work. They should know the nature of the hazard and the means for protecting themselves from the hazard. The Act also emphasizes the need for training miners by requiring that new miners receive 40 hours of training before working underground and 24 hours of training before working on the surface. The Act also requires eight hours of refresher training annually. This training must include information on the relevant health hazards and the potential consequences of overexposure. Before I close, I would like to mention briefly another source of principles that MSHA often consults to obtain guidance for both the development and enforcement of regulations. These are the various court decisions that are handed down from time to time. Two in particular that I want to stress are the recent Supreme Court Decisions on benzene and cotton dust. Although neither of the decisions has a direct impact on mining or radiation, they do clarify some general principles and directions for regulatory agencies, such as the role of cost-benefit analysis and the need for risk assessment. In closing, I wish us all an open exchange of information for a productive and useful conference.

Jan 1, 1981

By R. Poulin, R. Pakalnis, D. Peterson

Introduction A comprehensive project has been completed at the University of British Columbia that focused on the development of a commercially competitive composite cable bolt. Laboratory evaluation consisted of pull tests, preliminary shear tests, grout column testing and scanning electron microscope evaluation of the composite cable bolt. Field implementation at five underground mines throughout Canada were completed for technical and overall performance evaluation of the new product. The project began in 1989 under the sponsorship of HDRK Ltd., a consortium of mining companies including Inco, Noranda and Falconbridge Ltd. The objective was to develop a cuttable cable bolt that would serve as support for a continuous miner within a hardrock environment (Mah, 1994). The bolt was required to be cuttable by a continuous roadheader without adverse effects to equipment, personnel and the milling process. From the beginning, the focus was to employ existing cable bolt installation technology (Goris et al., 1994) whereby the cable bolts are grouted within a 4.8-cm-diam (1.08-in.diam) or larger employing a portland cement grout having a water: cement ratio between 0.35:1 to 0.4:1. The prototype, developed from Phase I, was technically comparable to that of conventional steel cable bolts. However, high cost and limited accessibility hindered its commercial acceptance. The second phase of the project was sponsored by the British Columbia Science Council and Pacific Pultrusions Ltd. of British Columbia to locally develop a glass fiber cable bolt. This phase of the project has resulted in the DAPPAM cable bolt (Pakalnis et al., 1994). DAPPAM Cable bolts are the second most used support method in Canadian underground mines after mechanical rock bolts. It is projected that 870,000 m (2.9 million ft) of cable bolts are installed annually in Canada (Poulin et al, 1994). The objective of the research program was to develop a glass fiber cable bolt with similar pullout strengths to the conventional steel cable bolts (267 kN - 60,000 lbf). More than 200 laboratory pull tests were conducted employing standard cable bolt test procedures, as outlined by the US Bureau of Mines (Goris, 1994), to assess optimum rod and surface composition, geometry, number required, pullout and shear characteristics, among others. This resulted in the DAPPAM cable bolt (Fig. 1). It consists of 10 individual 0.6cm-diam (0.25-in.-diam) rods enveloping a 2.2-cm (0.8-in.) outside diameter, high-density polyvinyl grout tube. The composite used in the construction of the rods is comprised of about 65% glass fiber within a 35% polyester resin matrix (by volume). Through pultrusion (a continuous fabrication technique), the fibers and resin are combined into a composite material. The strength of the overall composite is largely governed by the material properties, the alignment [ ] of the fibers relative to the applied load and the density and interaction of the overall components within the composite. A further modification to the composite was the addition of a sand grit to the surface of the individual rod. This increased the overall bond strength between the rod and the cement-based grout, used to solidify the cable bolt to the rock mass. The grout tube has an inside diameter of 1.9 cm (0.75 in.) and is rated at a pressure of 1.72 MPa (250 psi). During installation, the grout is pumped through the annulus of the grout tube thereby filling the hole from toe to collar. Laboratory and field trials concluded that a minimum drill hole diameter of 4.8 cm (1.08 in.) be used to ensure optimum grout coverage. Table 1 compares the design strengths (as tested) for DAPPAM vs. the ultimate strengths for a conventional 1.6cm (0.6-in.) steel cable bolt. The characteristics for the steel cable have been derived directly or indirectly by Goris et al. (1994). A design tensile strength of 289 kN (65,000 lbf) was proposed for the composite developed. However, recent tests have indicated maximum breaking strengths of more than 400 kN (90,000 lbf) (Fig. 2). Figure 2 shows the load vs. displacement pull out curves for steel and DAPPAM cable bolts. The methods of testing were standardized so as to be able to compare the results directly. The shear strength of the fiberglass cable is largely a function of the surface area sheared. Shear strengths of 89 kN (20,045 lbf) were obtained for the configuration shown in Fig. 1 when sheared normal to the axis of the cable. The testing procedure was similar to the shear tests performed on steel by Goris (1993). It is important to reinforce the implication that critical bond strength has on the success of an overall support system.

Jan 1, 1995

By Edgar Urbaez

Production scheduling is one of the most important factors affecting mine planning. A program -Mine Scheduler -that aids mining engineers with the setup of an optimum open pit production scheduling algorithm has been developed. A mathematical model for open pit scheduling that optimizes the Net Present Value of the cash flows was formulated. A simulated data is formulated as a Mixed Integer Linear Programming (MILP) problem. What's Best by Lindo Systems is used as the MILP solver in Microsoft Excel. The implementation of the algorithm focuses on problem setup, allowing users to easily evaluate, simplify, and develop the model that best fits their production scheduling.

Jan 1, 1999

By C. W. Matthews

Introduction Screening is defined as a mechanical process which separates particles on the basis of their size and their acceptance or rejection by a screening surface. The key element in this method of particle sizing is obviously the screening surface, the medium that contains the apertures for the passage of the undersize material. This surface must be strong enough to support the weight of the material being screened, flexible enough to yield to the vibrating force applied to it, yet light enough to provide a reasonable ratio of open area to attain a practical through- put. To balance all of these factors is difficult enough. The problem is compounded, however, because screening media are made in a great variety of types, shapes, sizes, and materials of

Jan 1, 1985

By Jorgen Elbrond

Shovels, trucks and repair bays for the trucks each play their role in the capacity of an open pit operation. It is therefore convenient to have a procedure for the capacity calculation which takes all 3 factors into consideration in a comprehensive manner. This can be done by means of a cycle model, earlier developed for the shovel-dumper circuits, when the repair facility with its number of repair bays is added as a superimposed service system, which the trucks visit at certain specified intervals. The calculation model transforms the mechanical availability of the trucks into their operational availability. The system's capacity in truckloads per shift and the trucks' operational availability of certain combinations of shovels, trucks and repair bays are shown.

Jan 1, 1981