Search Documents

By Nick Chlumecky

INTRODUCTION Column-type supports are used to prevent roof falls in underground excavations. The first individual column supports were made from timber that was cut to fit the irregular heights of mine seams. Because the seam height of the material removed varied throughout the mine, timber posts generally could be used only once. During the I 920s, steel friction props began to appear in British and European mines, and, by the 1950s, thousands of these props were being used. However, the steel friction props were heavy, difficult to install, and difficult to recover. Furthermore, the friction props could not be preloaded, and their yielding behavior was rather erratic. In 1946, hydraulic props were introduced in En¬gland, and, within a few years, they replaced friction props throughout Europe. The first application of hy¬draulic props in the United States occurred in the 1950s, during early experiments with longwall mining. Modern technology and high-production mining procedures have combined to make the use of hydraulic props a very acceptable method of providing temporary heavy-duty support for production areas. In areas such as development headings, where only modest roof loads are expected, lighter-duty jackscrews, ratchet jacks, and light hydraulic props are used. ADVANTAGES OF HYDRAULIC SUPPORTS The acceptance of hydraulic supports has been wide¬spread during the past 25 years, proving their reliability and effectiveness in preventing roof falls. Some of the advantages provided by hydraulic supports are: 1) Individual hydraulic props can be installed within 30 sec, resulting in a minimum exposure of per¬sonnel and equipment to an unsupported roof. 2) Hydraulic props can be preloaded to more than 4.5 t (5.0 st), increasing the frictional resistance between the rock strata. Thus, the roof is kept tight, improving the behavior of the unsupported ground. 3) If gradual roof sagging or bottom heaving im¬poses an irresistible force, the hydraulic prop yields gradually and continues to support the ground. 4) The support capacities of the hydraulic props most widely used range between 10 and 20 t (11 and 22 st). Their support capacities are maintained during yielding to an irresistible force. 5) Hydraulic props can be recovered rapidly. Where no other supports are provided for the roof, as in pillar¬ing operations, the hydraulic props can be recovered by remote means. 6) The length of hydraulic props is readily adjust¬able allowing them to be reused in seams where roof height varies. 7) Studies of mining operations indicate that the use of hydraulic props increases both personnel safety and mine productivity. DESCRIPTION Figs. I and 2 illustrate typical hydraulic props used in mines in the United States. Fig. I illustrates a prop

Jan 1, 1982

By Y. F. Vasyuchkov

In general a term "unconventional mining or "non-traditional mining technology" getting more and more familiar to the mining engineering media. There are several alternating terminological combinations such as "in situ mining", "borehole mining", "shaftless mining", "mineless mining", "geotechnology" etc.; specific terms denote particular method of unconventional mining technology: "underground coal gasification in situ", "underground coal combustion in situ", "borehole hydraulic coal mining" and others. Principal scheme of unconventional coal mining technology is shown in Figure I:

Jan 1, 1997

By Paul L. Boni

Trona, Na3(CO3)(HCO3) ? 2H20, is mined in quantity from saline facies of the Eocene Green River Formation of southwestern Wyoming. The Green River deposits are the world's largest known resource of natural sodium carbonates. An estimated 127 billion tons of trona ore are known to occur in beds exceeding 4 ft in thickness (Wiig and others, 1995). Twenty-five trona beds, exceeding 3 ft in thickness, and covering at least 100 mil have been identified. The beds are numbered sequentially in ascending stratigraphic order. Trona beds underlie more than 850 mil (bed 17) and are up to 37 ft thick (bed 1) (Culbertson, 1966). Five underground mines, operating in beds 17, 19, 20, 24, and 25, process trona to produce soda ash (sodium carbonate). A total of 11,837,703 short tons of soda ash were produced from 17.1 million tons of trona ore in 1997 (Kostick and Clark, 1998). A detailed study of trona bed 17, using techniques of petrography and X-ray diffraction, has been undertaken in the Solvay trona mine, near Green River, Wyoming. A continuous, vertical-channel sample was taken from near the production shaft for this study. At this location, bed 17 is 12.6 ft thick and includes several stratigraphic markers that are easily correlated throughout the mine and in surrounding drill cores. Bed 17 in this area averages 90% trona through its entire thickness (Wiig and others, 1995) and 95-100% trona in the lower two-thirds of the bed. Mineral impurities include water-insoluble dolomite, quartz, pyrite, clays, and other minerals and partially water-soluble northupite and shortite. Northupite, Na3Mg(CO3)2C1, contributes to chloride contamination in the soda-ash product and is concentrated in the upper one-third of bed 17, which is left behind as roof rock. Northupite has two modes of occurrence: (1) as bedded strata with dolomite, chert, clay, and shortite and (2) between primary trona crystals in trona spar. Petrographic and mineralogic data indicate that this section of bed 17 was deposited subaqueously during its early and late history and may have undergone periods of deposition in a subaerial or marshy environment. Stratigraphic data indicate that trona accumulated at an annual rate of 2-4 in. per year. During trona deposition, dolomite, CaMg(C03)2, precipitated in parting layers when new water entered the lake, freshening supplies of calcium and magnesium. The lack of clay minerals in the trona facies suggests water input may be by means of springs, as opposed to overland flow. Clay occurrences in thicker dolomitic partings within the trona facies indicate periods of episodic overland flow, possibly resulting from storms in the surrounding basin.

Jan 1, 1999

By John Todhunter

Longwall mining is certainly not new in the United States, having first been used in the late 1800's in Illinois, but the surging acceptance of the method is relatively new. The number of longwall installations in this country are nearly doubling annually as this method continues to prove itself as a coal producer's delight terms of operating cost, performance and safety. Since 1951, several longwall installations have been tried in Barnes and Tucker Company operations. Although all efforts actually proved that the system itself could be used in prevailing conditions, it was not until 1967 that a unit was put in use that proved competitive with regular mining equipment, both conventional and Continuous.

Jan 1, 1968

By Bruce L. Bryson

In the past decade a principal growth area in refractory technology has been the development and use of extra high alumina refractories. The refractories user is asking for, and is prepared to pay for, higher purity, more dense materials with longer life, less maintenance, and better dimensional tolerance to meet the exacting demand of high output processes. High alumina and bauxite refractories are being used more and more to keep pace with the demand for guaranteed performance. The steel industry, for example, is starting to place great reliance on these products. A unique material now available with all the requirements for extreme purity and density is tabular alumina, already proving itself in many refractory applications.

Jan 1, 1973

By K. Papke

Nine western states contain significant barite deposits, but most deposits are in Nevada, which has been the principal western producer for more than three decades. Nevada produces about 85% of the total United States production, but about one-half of the barite consumed in the country is imported. Approximately 95% of the barite is used in drilling muds. Sharply decreased oil and gas drilling, starting in early 1982, severely depressed the domestic barite industry. Other problems for western barite include long distances to the areas of major drilling, high railroad-freight rates, and increased barite imports. Bedded deposits, formed by submarine exhalative processes, account for almost all western production, and reserves are large.

Jan 1, 1983

By Roland Froidevaux

The potential use of geostatistics for quantitative ore reserve reporting is shown using a simple gold case study as an example. The need of defining quantitative class limits is stressed, and a possible approach to this problem is suggested.

Jan 1, 1983

By A. Bruce Waugh, W. W. Wen, Kevin N. Clark, Neville C. Lockhart, Bruce A. Firth

Australia is the world's largest coal exporter, and technological advancement is a key element of the coal industry strategy. The issues include: increased recovery of saleable coal; enhanced quality, i.e. lower ash, moisture, fines, phosphorus (sulphur is a relatively minor problem for Australian coals); better quality control; higher throughputs/lower costs; improved handling and transport; and reduced environmental impacts. In process terms, many coal preparation operations, particularly fine coal circuits, are relatively inefficient, and all circuits must also be matched and integrated for optimum overall operation. A holistic approach to technological improvement is desirable. This paper summarises research and development efforts, within CSIRO and its collaborators, across the unit operations as outlined in the title.

Jan 1, 1995

By David J. Kruse

The proper modeling of granular flow using discontinuum mechanics has the potential to be one of the most significant scientific advancements in the mining industry today. This paper will examine the status of discrete element technology, specifically focusing on current and future applications. The fundamentals of the Discrete Element Method (DEM) will be briefly introduced, as well as relevant design parameters. Various types of granular flow problems currently being solved using the DEM methodology will be presented. The results and potential benefits of these cases will also be discussed. All simulation results and figures used throughout this paper are from studies and designs preformed by the DEM group at Conveyor Dynamics, Inc. (CDI).

Jan 1, 2000

By A. Andreas

The transportation of mine products incurs a cost which can have a significant bearing on the competitive position of the product. This statement not only holds true for the transportation of the finished product but certainly as much for the in- plant haulage of the raw materials. Extensive literature is available both in North America and Europe on all aspects 02 these questions and to cite only a few of them: Pipelining of slurries, oil and gas, shipping of minerals and oil from the Arctic by icebreaking tankers, airlifting of metals or concentrates, etc. This paper is concerned with movable crushing plants as opposed to stationary and their influence on the in-plant transportation, that is trucks vs. belts.

Jan 1, 1973

By Jan W. Oberholzer, Patrick Linzer

The globally increasing environmental awareness which has manifested itself in the past few years also encompasses problems associated with mine closures. A crucial requirement for the effective planning, management, monitoring and control of mine closures is an information system which allows the qualitative and quantitative evaluation of proposed closure strategies, not only in terms of their local influences, but also of their potential effects on areas farther a field. This paper describes some of the closure associated problems and the establishment of such an information system from existing facilities, all of which are readily available. No modifications to these facilities are necessary, which enables rapid and cost-effective implementation of the system.

Jan 1, 1996

By Bryan A. Bartley

About 1,000 machines around the world are breaking rock and hard abrasive materials by a very economic, high intensity, autogenous process, but this method is largely ignored by the mining industry. This vertical shaft autogenous impact crusher has impact velocities around 70 m/s, which compare with those of Cascade and SAG mills of up to 10 m/s. The autogenous impact, breakage processes are all at higher intensity levels and the products reflect this difference. The topic of liberation is breifly considered. A series of tests with a laboratory scale machine are reported to illustrate a number of the characteristics of the process. This paper highlights topics for further evaluation and research.

Jan 1, 1992

By R. M. Yeates

Public concern over possible degradation of groundwater resources has resulted in an array of Federal laws and corresponding state laws to regulate contaminates from solid and hazardous waste. A mine owner must be familiar with environmental regulations which could impact his operation and must know what precautions and corrective actions to take in order to protect his mining operation from potentially expensive remedial actions. The Environmental Protection Agency (EPA), has issued few regulations controlling the management of mining wastes. Federal regulation of mining came primarily under the Surface Mining Control and Reclamation Act (SMCRA) administered by the Office of Surface Mining (OSM). Waste generated from the extraction, benefication and processing of ores and minerals was exempt from regulation under the Resource Conservation and Recovery Act (RCRA), which is EPA's major instrument in controlling surface contaminates. On December 31, 1985, EPA submitted to Congress a report entitled "Wastes from the Extraction and Benefication of Metallic Ores, Phosphate Rock, Asbestos, Overburden from Uranium Mining and Oil Shale", which will be referred to, henceforth, as the Congressional Report. This Congressional Report assessed the possible adverse effects of mine associated wastes. This report is the first step toward developing regulations with which EPA can regulate waste from the extraction, benefication and process of mineral ores.

Jan 1, 1987

The issues involved in mine closure are usually complex, and the risks are significant. Although environmental risks are paramount, other issues such as safety, community, legal, fiscal and technical factors need to he taken into account. This paper describes a simple empirical model based on the concept of the closure risk factor, which will enable decision-makers to analyze the mine closure risks at any site, regardless of the complexity of the issues and the scale, scope and location of the operation. The model enables all the issues to be captured and their individual and collective risk quantified. A number of case studies in Australia and the Pacific that illustrate the usefillness of the model are presented.

Jan 1, 2002

By F. C. Loughnan, Shane B. Sadleir

Bauxite is currently produced at three centres in Australia: - Weipa in northern Queensland; Gove on the northeastern tip of Northern Territory; and in the Darling Range near Perth, Western Australia. At each of these centres the bauxite is of Tertiary age and occurs as blanket-like, lateritic crusts in which gibbsite is the predominant mineral. Development was essentially in situ although possibly the deposits, particularly at Gove, are in part of transported origin. All of the deposits formed from quartz-rich parent rocks with those at Weipa and Gove being derived from kaolinitic sands while in the Darling Range, granite and other crystalline rocks of Precambrian age immediately underline the lateritic bauxite.

Jan 1, 1984

By B. Govindarajan, L. S. Rao, T. C. Rao, B. R. Rao

Laboratory leaching experiments were conducted to extract potassium from glauconitic sandstone, and the effects of important variables were studied. The reduced time plot (RTP) for all of the variables obtained from the experimental data has been quantified by this simple equation: R = 100 (1 - exp (-0.693 *(T/T50)0.605) The time required for 50% extraction (T50) has been correlated by a regression equation to variables such as acid strength, temperature, fluorite: glauconite ratio and % solids. Both of these equations were used to predict the extraction percentage at different process-variable levels. In addition, several other experiments were conducted at arbitrary levels of the variables to verify the equations developed.

Jan 1, 1994

By Robert G. Woolery

Union Carbide_ began looking seriously at heap leaching in 1971. At that time some 1.6 million tons of mineral averaging 0.040% U308 were stockpiled at various sites around the Gas Hills, Wyoming, uranium facility. Several alternatives for economically exploiting these reserves were considered and heap leaching seemed the most attractive. At the time, Western Nuclear Inc. was operating a heap leach project nearby in which the low-grade ore was leached with sulfuric acid, the product liquor treated in an on-site solvent extraction circuit, and the stripped product liquor re-acidified and recycled. They were most generous in allowing us to visit their site, answering our questions, and were helpful in discussing the problems associated with heap leaching. They confirmed our belief that, it was possible to operate a heap leach profitably on material too low grade for. conventional milling. Based largely on what we had learned from Western Nuclear's experience, a program was set up involving a laboratory study to determine the characteristics of the mineral stockpiles as related to heap leaching and to conduct a pilot heap leach adjoining our Gas Hills mill. Basically, the pilot heap construction and leach procedure were similar to those described in the literature(1,2) with certain modifications to permit detailed monitoring of the operation. In May, '1972, the decision was made to construct a test heap. The UCC plant at Gas Hills, Wyoming was selected as the most appropriate site for the follow¬ing reasons:

Jan 1, 1977

By D. J. McKee, D. M. Wiseman

The usefulness of simulation as a technique for metallurgical process design and optimization studies has been greatly extended over the last few years by the development of a number of general purpose simulation packages. The packages, or simulators, all have the common objective of presenting the mathematical models and simulation methods in a form which is readily usable by plant engineers and metallurgists. To date, most simulators have been concerned with steady state simulation, but packages capable of dynamic simulation are now becoming available. The paper outlines the essential features of versatile steady state and dynamic simulators. Typical applications are presented by considering examples of design and optimization studies. Limitation on the use of simulators are also presented.

Jan 1, 1991

By Peter McKenna

A mineral rights holding can ultimately only be turned to account by the profitable mining of ore on that property. The evaluation of South African gold mineral rights properties must therefore be carried out by assuming that they have potential to form part or all of a future gold mine. Such analysis involves the simulation of many of the estimation procedures that are normally carried out in a full feasibility study of a new mining venture but using far less data. This paper describes in detail the evaluation procedures that may be applied to an individual property and then indicates how these techniques can be applied to a whole mineral rights portfolio.

Jan 1, 1989

By J. Iannicelli

High intensity, high gradient magnetic separation can economically remove weakly paramagnetic contaminants down to 0 1 micron from industrial minerals This process is employed by all waterwashed kaolin producers in Georgia where seventeen huge magnetic separators are used to upgrade this product As a result, reserves of kaolin in Georgia have been doubled Design improvements have steadily increased the efficiency of separators and reduced power consumption below 300 KW for a nominal 65 TPH unit Beneficiation of ultrafine minerals is discussed based on pilot plant results on bauxite, ball clay, calcium carbonate, glass sand, talc, and numerous other minerals Operating parameters of the process are reviewed and some alternative equipment configurations discussed

Jan 1, 1983