Search Documents

By J. P. Hanten, G. Ramadorai

This paper presents laboratory and pilot plant data on the removal of heavy metals and molybdenum from mining-milling waste water. Molybdenum is removed as an Fe-Mo precipitate by proper addition of ferric sulfate. Heavy metals are lowered by lime treatment. Solid-liquid separation was achieved in both cases by flotation techniques. The Lectroclear electrocoagulation-electroflotation process was used to achieve the desired degree of metals removal. Good correlation was obtained on the laboratory and pilot plant scales. A two-step process consisting of the sequential removal of molybdenum and heavy metals was tested successfully using a mobile pilot plant. Preliminary data on sludge characteristics was obtained and the feasibility of recycling the iron sludge for iron and molybdenum recovery was established on the laboratory scale.

Jan 1, 1987

By John O. Marsden

Process selection is the systematic development of the optun.m metal extraction route for a particular feed matenal and has two main objectives: (1) to optimize project economics, principally a function of gold recovery, throughput rate and processing costs, and to develop a process that satisfies all of the proct requirements including, for example, political and environmental considerations.

Jan 1, 1992

By R. D. Lopez

The concept of "heat recuperation" for the grate-kiln pelletizing system was first implemented at the Sydvaranger plant in Norway in 1974. Essentially, heat recuperation involves bringing hot air from the second stage of the pellet cooler to the drying zone to increase drying-air temperature to the maximum limit. 'Burner-fuel savings result from a lower kiln secondary-air mass flow at a higher temperature. Because of the fuel benefits achieved at Sydvaranger, heat recuperation has been included innumerous new grate-kiln plants built since then, and some older plants have been retrofitted for heat recuperation. In recent years there has been much confusion about the fuel benefits of heat recuperation. To answer some of the questions, a mathematical model was developed and plant tests were conducted at Minntac Phase 111. Minntac is a magnetite taconite concentrating and pelletizing plant, and Phase III has two indurating lines. This paper presents the results of the studies and plant tests.

Jan 1, 1980

By Satya Harpalani

An investigation was carried out to study the microscopic structure of coal in order to understand the phenomenon of methane migration. A Scanning Electron Microscope (SEH) was used to study the surface and pore structure of bituminous coal taken from an underground mine. Micrographs obtained showed the highly porous nature of coal which explains the large quantities of gases that remain within the pores in the compressed and adsorbed forms. These micrographs further showed that most of the pores within the coal matrix are the 'dead-end' type and do not contribute much towards the flow of gas. The most important finding was that solid coal has a network of cracks and fractures indicating that it is these cracks that are primarily responsible for the gas flow, rather than the pores. The size and distribution of the pores within coal influence the capacity of coal to retain methane but movement of the gas molecules is the responsibility of the microfractures. Any mathematical modeling to simulate gas flow through coal must take this into account. For purposes of modeling, the structure of coal can be considered to have dual porosity. First, the gas molecules are released from the pores and there is a gradual migration towards the fractures. Once the gas reaches the fractures, its movement is eased greatly along these fractures.

Jan 1, 1987

By T. Grammatikopoulos, C. Gibson, M. Aghamirian

"Lithium is a soft, silver-white alkali metal with atomic number 3. As of 2015, the end use of lithium was estimated to be as follows: lithium-ion batteries (35 percent), ceramics and glass (32 percent), lubricating greases (9 percent), air treatment (5 percent), continuous casting mould flux powders (5 percent), polymer production (4 percent), primary aluminum production (1 percent) and other uses (9 percent) (Jaskula, 2014). Lithium is found in brine lake deposits containing lithium chloride and in hard rock pegmatite deposits. It can be sold in a range of product types; as mineral concentrate, brine, compound (lithium carbonate or lithium hydroxide) and metal depending on its intended end use (Goonan, 2012; Jaskula 2014).In the 1990s, the United States and Chile were the largest producers of lithium globally, primarily from brine operations (Ober, 1994). Most of the lithium compounds produced during this period were consumed in the glass, ceramics and aluminum industries. In the 1980s and 1990s, there were two major lithium operations in the United States: brine operations at Silver Peak, NV and a spodumene mine and lithium carbonate/lithium hydroxide plant in Kings Mountain, NC. The Kings Mountain operations ceased production in 1991 and were eventually dismantled in 1994. Brine operations were also active in Argentina and Chile, while the largest lithium ore deposit in the world was operated at Greenbushes, Western Australia. During this period, it was predicted that major shifts in demand for lithium would come from the success and widespread use of electric vehicles (Ober, 1994).Lithium is still produced from the brine operations at Silver Peak. But in more recent years, Chile has become the world’s leading producer of lithium carbonate from brines. Australia has maintained its position as the world’s largest producer of lithium mineral concentrate, the majority of which is exported to China to produce lithium carbonate and lithium hydroxide (Jaskula, 2014).A spodumene concentrate was also produced at the Tanco Mine in Manitoba, Canada beginning in the 1980s through to 2010 when lithium operations were suspended due to fluctuations in the lithium market price (Martins et al., 2013)."

Jan 7, 2017

By W. C. Baver

Even before the energy crisis developed in the early '70's, considerable research world-wide was being directed towards the development of schemes to both reduce the energy requirements and to reduce air pollution emissions associated with the manufacture of glass. In many cases the sought-for solutions would benefit both objectives. If, for example, the glass batch could be consolidated into such compact forms as briquettes or pellets, they could be preheated in a moving-bed heat exchanger with the high-temperature exhaust gases from the glass furnace. Lower furnace temperatures would thus be possible with a corresponding reduction in heat losses and total fuel consumption. Moreover, the lower temperatures would also reduce the amount of nitrogen oxides generated in the furnace and emitted to the atmosphere. Many tests on consolidated glass batch have been run in many countries. In some cases, extended tests on production furnaces have also been included in the programs. For various reasons, however, none of these has proved to be economically attractive. The current, but temporary lull in the rapidly rising cost of energy which has been with us in recent years, has reduced the push for research for energy saving means for melting glass. A few of the current programs will be discussed. Since raw material requirements, primarily physical in nature, are affected by some of these schemes, these will also be considered.

Jan 1, 1986

By Barry N. Doyle, Tarcisio M. Carvalho, Alan K. Haines, Marcos P. de Melo, Edward J. da Silva

A metallurgical complex to recover gold from highly refractory arsenical ore was recently commissioned by Sao Bento Mineraco. The plant, with a nominal capacity of 20 000 tonnes per month, is situated in the Minas Gerais province of Brazil. The process consists of run-of-mine milling, flotation, pressure oxidation of the concentrate, carbon-in-leach, elution and electrowinning, and effluent disposal. The paper provides an account of the investigations that resulted in the decision to install the pressure oxidation circuit, process and engineering design and plant start up. A comparison is made between the results achieved during the first two years of production and the design parameters.

Jan 1, 1989

By A. M. Johnson, M. A. Cornachione

The west central Upper Peninsula of Michigan contains a large resource of graphitic slate. The slate has potential industrial use as a substitute for shale currently used in the production of portland cement. Some of the unweathered slate, however, has a high concentration of pyritic sulfur that can create emission problems when processed in a kiln. A low-cost method to reduce the sulfur content of the slate through the optimization of pyrite oxidation in a bio-heap leaching operation was investigated. In this study, optimal conditions for the bacterium Thiobacillus ferrooxidans were created to promote pyrite oxidation and, therefore, sulfur removal from the slate. Preliminary lab scale flask tests using crushed and sized slate (-40 + 100 mesh) and T. ferrooxidans bacteria in a sulfuric acid medium resulted in 70% oxidation of pyrite over a one-month period. Subsequent column leaching tests on coarser materials (-3/8+1/4 in.) operated for six months resulted in a maximum reduction of total sum of 75%. These data suggest that bio-heap leaching to remove sulfur from the slate for use as a kiln feed material is viable.

Jan 1, 1995

By A. Probst, N. Moores, J. A. Finch

In 1994, McGill University and INCO Ltd. (Sudbury operation) initiated the transfer of technology originally developed to detect levels in equipment ranging from flotation columns to thickeners. A conductivity probe was installed in a concentrate thickener to monitor the mud line and the solids load. The probe consisted of a vertical tube with 32 equally spaced electrode rings connected in pairs to give 31 conductivity cells. Conductivity was measured as a function of depth to produce a conductivity profile. From the conductivity profile, the mud line and the percent solids can be inferred. The probe was installed in October 1994, and it has been successfully detecting profiles since then. This paper includes a description of the incidents that occurred and the experiences gained during this technology-transfer process. Discussed is probe installation and startup; software modifications to accommodate both operating conditions and the needs of the operators; and calibration procedures to adjust to changes in performance as a consequence of long-term use. Also included are preliminary observations of the still-in-progress last stage, i.e., signal interpretation and use to facilitate operation, particularly by providing early reaction to upstream disturbances.

Jan 1, 1999

By F. L. Wilke, J. Fabian, D. Oravec

The task of production planning in ore mining is primarily con¬cerned with the removal of ore blocks within planning periods spread over the life of the mining operation. The investigation of this problem in the past resulted in the introduction of computer based optimizing techniques for production scheduling and se¬quencing. Although these techniques succeed in computing an "optimal" mine output for one planning period, they usually fail in composing a practical and feasible mine plan over the periods in concern. This paper describes conventional production planning based on operations research and the capabilities of a knowledge-based approach. An example of a planning system for the Slovak under¬ground iron ore mine Nizna Slana will be presented. By combina¬tion of these two techniques this system should improve the qual¬ity of planning procedures.

Jan 1, 1996

Adsorption experiments were conducted at two different solids loadings, to investigate the mechanism of oleate adsorption on apatite. Adsorption density at pH 10 was found to be dependent on solids loading in an oleate concentration region where surface precipitation could occur. Analysis of adsorption isotherms indicated three distinct regions of adsorption. In the region I (below the region of calcium oleate precipitation), molecular adsorption was observed. Simultaneous molecular adsorption and surface precipitation occurred in region II, while surface precipitation was predominant in region III along with some bulk precipitation. Correlation between flotation of apatite with sodium oleate and the mode of oleate interaction with the surface is established.

Jan 1, 1986

By B. C. Haydon

Manganese silver ores are well known to be refractory towards cyanidation. Various processes have been suggested for improving the amenability of these ores. A sulfurous acid pre-leach is one such process. This paper traces the development and implementation of the sulfurous acid pre-leach process for the retreatment of manganese silver tailings at Tonopah, Nevada. An account of the test work program is presented, followed by a description of the operating plant and specimen metallurgical performance. The paper also summarizes the history of the Tonopah tailings, their mineralogy and makes reference to previous application of the sulfurous acid pre-leach process.

Jan 1, 1984

By J. M. Mutmansky, B. Kolonja

A PC-based simulation model using the software packages SIMAN and CINEMA was developed to simulate and animate truck-shovel operations. The model is capable of simulating one mathematical dispatching strategy using linear and dynamic programming and six heuristic dispatching strategies. Data were collected from an actual operating mine through time studies and analysis of historical records. Statistical analyses were performed, and appropriate theoretical distributions were fitted for various time events in the truck-shovel cycle. The model was then applied to study overall impact of these dispatching strategies on constrained and unconstrained mine productivity. The simulation/animation model developed in this study seems to be an efficient planning tool for choosing optimal fleets and finding an optimal dispatching strategy to produce an equilibrium between the quality and quantity of production.

Jan 1, 1995

By M. E. Gershon

Extensive efforts are under way toward applying computer techniques to mine production scheduling problems. These efforts are concentrated in four areas: optimization, computerization of traditional methods, heuristics, and simulations. These areas complement each other rather than compete. Characteristics of each are discussed toward enabling the engineer to evaluate specific systems that may be encountered. Alternative approaches within each classification are described as well as the motivation for each.

Jan 1, 1987

The height of permanent slopes at the Panguna mine of Bougainville Copper Limited will vary from 350 to 950 metres. A few degrees difference in slope angle has a large effect on the ore/waste stripping ratio. Optimum slopes can be achieved if longer batter slopes (exceeding 45m height) are excavated using bulldozers to trim parallel to controlling fracture surfaces. Unnecessary slope flattening by incorporating benches can cost millions of dollars in lost ore. Faults and other major weaknesses, which can result in wedge failure or erodible zones have been treated successfully with shotcrete, rockbolts and cable dowels. To minimize support effort and interference with mine production, early identification and treatment of unstable areas is important.

Jan 1, 1987

Australian underground coal mines predominately use the longwall method for coal extraction. In longwall mining at least two parallel roadways known as gateroads are mined to delineate the sides of the longwall block, a longwall installation face is then driven connecting the gateroads to enable the longwall mining equipment to be installed. Roadway development should ideally be ahead of the longwall so that the longwall equipment can be installed into the newly developed panel with minimal delay to coal production. A discrete event model of roadway development can help assess how a particular configuration may perform with high levels of variability and uncertainty in operations. One of the major delays associated with roadway development is caused by the shuttle car due to its cyclic stop-start nature. Shuttle car travelling paths and machine interactions are normally constraint by the mine?s roadway layout and mine safety issues. This paper presents simulations of shuttle car route options which can be considered at the design stage to minimize the cycle time of a shuttle car as part of a general roadway development simulation model developed using 3D Flexsim.

Feb 23, 2014

By Aixiang Wu, Minjie Zhang, Zhuen Ruan, Yiming Wang

 The paper combines theoretical and experimental analysis to improve the accuracy of predicting paste yield stress by slump flow. It derives an analytical model of slump flow for yield stress, providing a theoretical basis for quantifying the rheological properties of paste with slump flow. The study uses three different tailings-prepared pastes and constructs an empirical yield stress model, showing high accuracy and good generality.

Aug 1, 2023

By M. V. K. Reddy

A differential flotation process for recovery of molybdenite from chalcopyrite concentrates produced at Rakha Copper Concentrator, Bihar, India has been developed. The flowsheet is simple, and relatively inexpensive and yields a concentrate assaying not less than 45% Mo at a recovery of minimum 65%, starting from chalcopyrite concentrate assaying 0.4% Mo. The consumption of the main depressant used, sodium sulphide is not more than 25 kg/t of copper concentrate processed without steaming; and with steaming the consumption was brought dorm to less than 12 kg/t of concentrate. Further reduction is possible by optimization of steaming parameters. Based on laboratory experimental results, further tests were conducted on concentrator site and process design parameters were established for design of commercial plant.

Jan 1, 1982

By Clay Haynes, Tim Pearia, Robert Robinson, Judy Cochran

A 1.89 km-long, 4.5 m-I.D. tunnel was successfully constructed through saturated hard clay, and highly abrasive dense sand and gravel, with groundwater heads ranging from 10 to 20 m. In order to address these conditions, a Lovat earth pressure balance TBM was used, with soil conditioning by foam, water and various polymers. Support was provided by a single-pass segmented concrete lining. Groundwater inflows of 400to 1,600 lpm at times created challenges for changing cutting tools. Surface settlements were generally less than measurement thresholds, except under very low cover at startup. This project provides a pivotal case study of the successful application of EPBM technology in saturated, abrasive glacial soils and the successful application of soil conditioners.

Jan 1, 2003

By Matthew E. Fowler, Jean Habimana, Roy F. Cook

The West Side CSO Tunnel, Pump Station & Pipeline Project is currently beginning construction along the downtown waterfront of Portland, Oregon. This4.3 meter diameter, 5,500 meter-long soft ground tunnel will be driven along the westbank of the Willamette River adjacent to buildings and utilities and several major pile-supported bridges. High groundwater pressure, extended lengths of gravel to cobble-size alluvium, and the need to control ground loss and surface settlements were key considerations in the selection of slurry tunnel boring machines for the project This paper presents an overview of the numerical modeling that was performed during design to estimate the strains and additional loads in the pile-supported structures and to assess the efficiency of proposed mitigation measures.

Jan 1, 2003