Search Documents

By G. M. L. Robinson

The Clean Water Act, as administered by the Environmental Protection Agency, has mandated industry, government and the public to comply with potentially conflicting and vague water quality statutes, regulations and guidelines. Universal regulatory strategies have been developed which have introduced and have created regulatory, compliance and institutional conflicts. Conflicts have been created because National water quality performance goals and design standards are vague, and, in many cases, cannot be scientifically justified. Because of regulatory technical requirements to define background and environmentally impacted water quality characteristics, the ability to achieve regulatory compliance is difficult. Difficult issues requiring resolutions includes but are not limited to site specific surface and ground water quality classification systems, water quality standards and guidelines, point and non point pollution sources etc. Because of these statutory and regulatory complexities, a confrontational regulatory system has been created as it relates to: - defining performance criteria in relation to design criteria; - resolving water quality statistical compliance conflicts; - defining laboratory precision requirements; - determining background groundwater characteristics; and - locating a representative point of compliance. Because of these complex regulatory issues, the ability to balance goals, needs and economics has not been achieved or in many cases has not been attempted, without legal intervention. A few examples illustrating where water and waste management compliance conflicts have been experienced.

Jan 1, 1992

By M. C. Mound, L. Fradette, C. Colbert

Metallurgical Accounting in the mineral processing industry transforms accumulated process data, including flow rates and assays, into a coherent information format. This is used to rapidly provide production reporting and key performance indications. A fully comprehensive and coherency of available data must be a component of any system expected to accomplish reconciliation in the mass balancing process. Quality issues are thus improved with such desired methods via a mass-balancing engine utilizing the results of measurements acquired by various on-line sensors, analyzers, and sophisticated laboratory equipment. Metallurgical Accounting, when accomplished through such an engine, provides high value information in a simple, straightforward, and simplified manner. Exceptional utility is then transparently available to authorized personnel for access to metallurgical accounting reports, production reports, mass balance results, performance indicators, and so on. This paper discusses how such information can be used to "drilldown" into each result set by consulting the data hierarchy to evaluate and validate calculations and input data used to produce the specific results being queried. The power of such a system resides in the full and true integration of all production and laboratory data. What is integrated are the data thus acquired via a single user interface, a single database, a single configuration tool, etc. From this comes the derivation of contextual information and its maintenance. It is possible to reduce metallurgical accounting and production reporting from possibly hours or even days to a matter of minutes. The result is maximization of information reliability and availability from masses of otherwise discrete and difficult to access key data.

Jan 1, 2003

By B. H. Kim

The use of a 25.4 mm diameter water-only hydrocyclone for separating fine-size (-150 µm), high-density (>4.5 g/cc) particles from similar-size, lower-density (2.65 glee) particles was investigated. It was found that a single-stage separation recovered nearly 90% of the heavy minerals (7.0 g/cc), while achieving a volume reduction of about 70%. The use of dense medium in a single stage improved volume reductions to 90% at similar heavy mineral recoveries. In addition, computer simulations of a three-stage circuit were performed, which showed that recoveries approaching 97% with volume reductions of 95% were possible.

Jan 1, 1998

By R. D. Lord

This paper deals with the search for the best practical means of storing sulphide bearing tailings, where there is no residual excess of carbonate material. It is the common experience that the sulphide content decomposes, with the aid of bacterial action, and the resulting sulphuric acid escapes, along with any heavy metal solutes, through embankments that are usually porous to some degree. The problem is typified in the tailings of the uranium operations of Elliot Lake, Ontario, where mining started some 20 years ago. The approach to tailings disposal paralleled the practice for other hydrometallurgical plants treating gold and base metal ores. Impoundment areas were designed to retain solids, and a clear and neutral overflow was considered satisfactory practice. Now experience has shown that these areas, some idle for over a dozen years, release acids, in seepage and overflows, to an unacceptable degree. To protect natural water courses neutralizing plants are operated wherever required. Lime slurry is fed continuously into the tailings outflows in a quantity sufficient to raise the pH to 8.5 and precipitate heavy metals that may be in solution. The objection to this procedure is that the plants will require servicing indefinitely, unless a better remedy is found.

Jan 1, 1975

By M. McPherson, G. Danko

Methods of measuring in situ rock thermo-physical properties are rapidly evolving. Among those existing in the literature, a particular measurement procedure was selected for further development. The measurement is based on creating a spherical temperature field in a drill hole using a point source heater of constant heat flux. The bivariate temperature distribution 0 (r, t) is measured at several points along the length of the drillhole, radius r from the heater and at particular time intervals (t). A number of different evaluation methods were tested for calculating the unknown thermal conductivity (k) and diffusivity [] from the measured temperature and the known heat flux. The results showed that evaluation using the finite difference scheme and small temperature differences measured at points close together, cannot give a reasonable result. In order to solve the problem a new general analytical evaluation method is developed. Using an appropriate technique, it is possible to simultaneously obtain values for k and [], incorporating a semi least square technique to reduce the uncertainty in the evaluation. The new device and evaluation method makes it possible to obtain from a single drill hole highly precise k and [] values within an 8 hour period. The method has been used in several underground mines in the U.S. with good results.

Jan 1, 1987

By Andrew N. Peterson

US mine operators frequently fail to investigate more cost effective and productive bulk material handling systems because surface mines seem to lend themselves to truck ore haulage. In this country, as a result, use of conveyors to move heavy loads from mine to process facilities has been minimized, if not actually neglected. In contrast, there are more than 50 conveyorized surface mines in successful operation around the world. These mine operators have learned that properly applied conveyorized systems can offer major savings in capital and operating costs, which contribute to improved profits when combined with other proven mining technologies. Growing acceptance and application of conveyorized bulk material handling in surface mines also points up how unique each mine is and how careful planning contributes to maximum mine effectiveness. Because of these differences, mining executives and technical and operating staffs need to develop an understanding of three factors in applying conveyorized bulk material handling in surface mines: • Why each mine will benefit from the type of automation permitted by conveyorized operation, •What kind of equipment is available, and • What applications most effectively demonstrate the first two factors in action - hauling either ore or waste. The conveyorized systems considered in this presentation have production rates from 0.5-2.7 kt/h (500-3,000 stph). Worldwide, these systems have been operating since the early 1960s. Advantages of Conveyors Why do you want conveyorized bulk material handling? First, it almost always provides lower operating and maintenance costs. Second, it frequently requires lower initial capital costs and almost always requires lower capital costs over the life of the surface mine. Third, it provides comparable operating availability, and finally, it frequently gives comparable operating flexibility - depending on the mine plan. Cost avoidance can be accomplished with modern production methods. These, in turn, permit increased productivity and reduced operating costs such as those for energy, maintenance, and manpower. It has been demonstrated in European surface mines and elsewhere, that conveyor systems frequently require lower initial costs than does truck haulage. Almost always such operations require lower capital costs over the mine life. Those costs include the continual addition of haulage trucks to both accommodate the increasingly difficult haulage routes and fulfill replacement requirements when trucks wear out. Conveyor systems handling ore in numerous large crushing and port facilities, which have operated since the early 1950s, have clearly demonstrated a useful conveyor life of more than 25 years. In contrast, off-highway trucks have life spans of six to eight years. The following examples illustrate comparative capital costs to purchase conveyor systems and comparable truck haulage units. Example 1 The ore haulage route from point A to point B is level and 610m (2,000 ft) long. The material weighs 1.8 t/m3 (110 lbs per cu ft) and must be transported at a rate of 1.8 kt/h (2,000 stph). The installed capital costs to provide a properly designed conveyor that will transport the described material from point A to B is about $450,000. The capital cost to purchase three 77-t (85-st) off-highway trucks and one spare truck - which would provide equivalent capacity - would be about $1.2 million. The truck cost estimate is based on a 6 min. or 771 kt/h (850 stph) truck cycle time. Truck efficiency is estimated at 0.8. Each 77-t (85-st) truck would have an actual haulage rate of 617 kt/h (680 stph). Therefore, three trucks would be necessary to transport the designated tonnage of 1.8 kt/h (2,000 stph). A movable crushing plant would be located at point A for the conveyors and a permanent crushing plant at point B for the truck haulage system. Capital costs for these primary crushing plants were not included in the calculations for either system because the capital costs are frequently comparable. Example 2 The transport route from point A to point B is 610 m (2,000 ft) horizontally and 122 m (400 ft) vertically - on a 20% grade (Fig. 1). The material weighs 1.8 t/m3 (110 lbs per cu ft) and must be moved at a rate of 1.8 kt/h (2,000 stph).

Jan 6, 1983

By Frank H. Skelding

A new, large mine is about to be born. Many years and millions of dollars have been invested in exploration. An orebody has been found and proven. All necessary political and legal work to establish rights and conditions for development are complete. The feasibility studies are favorable. Financing has been arranged. Board approval has been given to proceed. The time has come to engage a contractor to design and build the new facilities in a location, as is the common case today, far re¬moved from the centers of advanced technologic development where the minerals will ultimately be used. A select list of Engineering and Construction (E&C) companies is asked to prepare proposals. At this point the common viewpoint among mining companies is that the company's sole remaining problem, a major one to be sure, is to select qualified contractors to design and build the project at the lowest cost and shortest time possible so that production can start generating a return on investment. The purpose of this discussion is to explore the viewpoint of the large E&C contractor toward such projects. It differs in important ways from that of the client mining company and it is these differences and the reasons for them that must be understood by the client if severe difficulties and misunderstandings with the contractor, starting at the beginning of contract negotiation and continuing through design and construction to final startup are to be avoided or minimized. Often enough, the difference is in degree, not kind, which only serves to obscure the fact that a difference exists.

Jan 1, 1975

By D. H. Dvorak

Two pilot-scale biological reactor systems were installed to treat metal-contaminated water. The reactors consisted of barrels and tanks filled with spent mushroom compost, within which bacterial sulfate reduction became established. Concentrations of Fe, Zn, Mn, Ni, and Cd were lowered by over 95% as these metals were precipitated as insoluble sulfides by reaction with bacterially generated H2S. The chemistry of the reactor systems is examined, and opportunities for maximizing their metal-retaining and alkalinity-generating potentials are discussed.

Jan 1, 1991

By James E. Gingrich

The new Track Etch* technique for uranium exploration has been utilized in several survey programs conducted during the last few years. The results from these programs have been very encouraging, and new uranium ore bodies have been discovered by using this new technique. The Track Etch method is being used in several exploration programs in various locations around the world. The Track Etch exploration technique utilizes small pieces of special radiation-sensitive plastic film to detect the presence of radon gas which is released by uranium ore bodies. Because of the selectivity and sensitivity of the technique, ore bodies not normally detected with other surface or airborne monitoring methods are found. Since no large equipment or special training of personnel is needed, the Track Etch technique is easily used in field operations. The basis for the Track Etch method, its application in field exploration programs, and the results obtained to date in locating uranium ore bodies is discussed.

Jan 1, 1974

By Douglas D. Donald

The financial analyst's job is to make an objective appraisal of the investment opportunities which exist within the various industries under his supervision within the context of the economic model provided by his firm and the a climate of investor sentiments. Industry analysis is critical. When a major investment trend develops, usually the stock of all companies within the specific industry react in the same direction. I should emphasize here, however, that an investment trend is influenced by the economic outlook, but economics is not the only determinant - investor psychology and arbitrary political factors may be of equal or greater importance. Part of our job is to recognize trends early and determine whether they are valid. Following industry analysis, the analyst must examine the specific companies within that industry since some companies usually react more violently than others to industry trends, whether they be favorable or adverse. To simplify the process of evaluating an investment opportunity, it is convenient to isolate three types of factors which have a bearing on every sort of business although the degree of influence of each factor may vary from industry to industry. These categories are, 1) independent or external factors insofar as they are beyond the control of corporate management, 2) interdependent factors insofar as influence may be exerted by industry-wide action, and 3) dependent factors covering the area of internal decisions which are basically under the control of the individual corporate managers. Although the title of this paper, "The Corporate Use of Cash Flow," is only one segment of the third category, it may be useful to continent on the first two categories as well. The independent factors may be either economic or governmental. The economic factors include cyclicality which may be very high in the case of the basic commodity industries or relatively low as in the case of utilities. Underlying growth rates, another independent factor, may range from the business equipment industry with an annual growth rate of 14% through the electric utility industry with a growth rate of about 7% per year to the

Jan 1, 1970

By Jonathan Ludlow, Robert A. Jankowksi

Introduction A longwall operator can make few changes to increase output, significantly reduce respirable dust, and decrease power consumption. Reducing drum speed, and thereby cutting with increased pick penetration, is one. This article defines the benefits of deep cutting in terms of reduced dust production and power consumption. It also identifies the practical aspects of high pick penetration in terms of shearer performance and coal loading. Before examining some practical aspects of reducing drum speed and looking at the theoretical background, it is worthwhile to summarize what is meant by high penetration and deep cutting, and what potential benefits and pitfalls may be expected. Deep cutting (in the sense of high penetration rather than wide web) can be defined in one or more of the following ways: • Cutting with an average pick penetration distance higher than that used in the past. • Cutting with a pick penetration higher than the longwall operator would have used if the advantages of deep and slow cutting were not considered. • Cutting with a well-designed shearer drum below 40 rpm. All these definitions are slightly arbitrary. They are given to provide a basis for discussion and to make the point that any move towards deeper, more efficient cutting can result in operational benefits. The benefits of deep cutting appear in many different areas. The most noticeable benefit, provided suitable instruments are available, is the reduction of airborne respirable dust. During an experiment on a longwall in the Pittsburgh seam, a nearly four to one reduction in dust levels was seen when drum speed was halved. Not all studies have shown such a big reduction, but it seems that some benefit is almost always obtained when drum speed is reduced. Production rate and specific power consumption are also affected (in a positive sense) by reducing drum speed or increasing pick penetration. Although these changes may not be as spectacular as those in dust level, they contribute to the economic return of the longwall operation. Similarly, improved washability through fines reduction may have a beneficial economic effect. Cutting with shearer drums operating at lower speeds does have some possible deleterious impacts that an operator should be aware of. For example, cutting reactions - loads imposed on the picks by the coal being cut - will be increased as a deeper cut is used. Steps must, therefore, be taken to ensure the stability of the shearer and provide an adequate haulage effort. These increased cutting reactions also result in higher loads on the power transmission system (gearboxes, ranging arms, pick boxes, etc.) from the shearer motor(s) to the pick tip. These higher loads must be anticipated and provided for with the necessary hardware. In particular, extra haulage power must be provided with low drum speeds, since haulage effort required increases roughly in proportion with pick penetration. Because the drum will be rotating more slowly or will have fewer picks, the load on shearer components will also be more variable. If suitable, robust equipment is not used, this increased vibration will decrease reliability. Benefits of Deep Cutting Lower dust levels, decreased specific power consumption, and improved product washability are the most noticeable benefits of reduced drum speeds. Although the benefits will vary greatly with mining conditions and the type of coal, some examples of what can be expected are described below. Reduced Dust Levels Figure 1 shows principal results of a study on the effects of reduced drum speed conducted on a longwall in the Pittsburgh seam (Ludlow, 1981). This figure shows that average dust production was reduced by about 70% when drum speed was halved. By making some assumptions about such quantities as coal density, it is possible to apply this proportional reduction to the quantity of respirable dust liberated per ton of coal mined. When this is done, two kinds of results are obtained: • At 70 rpm, about 1 g (15 gr) of airborne respirable dust is created for every ton mined (roughly one part per million). At 35 rpm, only 0.28-0.37 g/t (3.9-5.1 gr per st) of coal mined become airborne respirable dust. • At 35 rpm, nearly four times the amount of coal may be mined before the compliance level is exceeded, compared with 70 rpm.

Jan 3, 1984

By John L. Burnett

Field criteria are needed to help the prospector recognize a potentially expansible shale, clay, or slate. Certain criteria have proven useful in California even though the physical-chemical mechanisms of expansion are not thoroughly understood. Three conditions must be satisfied before expansion can take place, The raw material must partially fuse at a low temperature (1800-2000°F.), Concurrently a gas must form. The raw material must be sufficiently impermeable to trap the gas within the particle. Low temperature melting, which is controlled by bulk chemical composition, is difficult to assess in the field but most common shale, clay, and slate is suitable in this respect, The presence of organic carbon, the most common source of an expanding gas, is indicated by dark color of the rock, A large proportion of clay-sized particles promotes impermeability; fine grain-size is indicated by conchoidal fracture, The shape of the expanded particle is commonly indicated by the texture of the raw material. Rocks with well-developed slatey cleavage produce accordion-shaped particles; massive rocks tend to form rounded particles. Undesirable materials commonly present with expansible shale include: weathered shale; sandstone and other coarse-grained sediments; and limestone, Weathering, which is indicated by color, reduces or eliminates expansion; therefore, surface samples seldom are representative of the shale found at depth. Sandstone does not expand and will increase the average weight of the finished product, Limestone or particles of carbonate minerals can be actively harmful because they are converted to free lime (CaO) during the firing process, If free lime is present in concrete, hydration will cause expansion of the lime particles which result in surficial ?popouts.?

Jan 1, 1963

By Wedam Nyaaba, Edward Wellman, Angelina Anani, Eduardo Cordova, Sefiu O, Cluber Rojas, Adewuyi

This study aims to investigate the optimal method for ore pass construction in incompetent rock masses. We evaluated the conventional and raise boring methods based on safety, efficiency, excavation control and ground support for ore pass construction. A stability analysis using analytical Q-raise (QR method) and kinematic analysis methods for ore pass construction with a raise borer before and after grout injection of the rock mass was performed. As a case study, an ore pass (diameter of 3 m, depth of 100 m) within an incompetent rock mass was considered to gain further insight. The rock mass was characterized according to the classification methods Q Barton, rock quality designation (RQD), rock mass rating (RMR) and geological strength index (GSI). The grout intensity number (GIN) method of grout injection was used. The safety factor of less than 1.075 obtained before injection was lower than the acceptance criteria. However, grout injection before raise borer excavation resulted in a safety factor greater than 1.5. Using a raise borer without pre-grouting indicated that the maximum unsupported diameter (MUSD) of the ore pass was less than the required 3 m and equal to or larger than 3 m post-grouting.

Dec 1, 2024

By D. S. Bird

The Kennecott Utah Copper Modernization Project, initiated in 1986, was directed to provide an expansion and modernization of mining and process facilities at the property's Bingham Canyon Mine and ore concentrators. Major components in the project included installation of an in-pit ore crusher, transfer conveying system, and construction of a new copper ore concentrator with a design capacity basis of 70,000 tonnes/day. The Copperton Concentrator was commissioned in February 1988. A principal feature of the plant is the grinding circuit, comprised of three identical lines, each consisting of a 10.37 m (diameter) by 4.57 m (length) Semi-Autogenous Grinding (SAG) mill and two 5.54 m (diameter) by 8.62 m (length) ball mills. The SAG mills are driven by two variable-speed 9,000 kW DC motors coupled through a clutch-pinion gear-ring gear assembly. The ball mills are driven by 4,125 kW synchronous motors coupled through a typical clutch-pinion gear-ring gear system. The expansion and particularly the Copperton Concentrator performance was so successful that by early 1989, management began examining options to further expand production capacity. With regards to the concentrator, numerous alternatives were considered, ranging from installation of a grinding line similar to one of the existing lines, to a "super" line consisting of a 12.8 meter (diameter) SAG mill and a 20,000 kW motor with a capacity of 50,000 tonnes per day. The technical and economic analysis of the various scenarios indicated that one "large" 11.0 meter (diameter) by 4.88 meter (length) SAG mill with a production capacity of 32,000 tonnes per day and a 12,000 kW drive would be optimum. The key question to be answered in the project was whether to continue with the pinion-ring gear combination, or install a gearless drive. The following paper outlines many of the items that were evaluated in the mill selection process followed by actual plant performance, and a discussion of ongoing plant continuous improvement projects.

Jan 1, 1995

By E. Allen Wendt

It is both a great pleasure and something of a challenge for me to have this opportunity to address a gathering encompassing such a wealth of expertise in the minerals field, It is particularly challenging because I have been asked to turn your attention from the relatively glamorous subjects of gold and money to the more mundane questions of our International commodity policy and the place of buffer stocks in that policy. However, these questions may be of more immediate importance for our economic interests at home and Abroad. I can testify that the problems affecting international commodity markets and the possibility of international action To resolve those problems are matters of real concern to Washington as well as to your industries,

Jan 1, 1978

By J. W. Devon

The coal mining industry is divided into two distinct economic segments based on Coal Supply Agreements. Coal supply agreements generally fall into two categories, spot or long-term, with the selected contract term being driven by the buyer's market expectations, security of supply considerations, fuel tonnage and quality requirements, and economics. Short-term or spot coal purchases are generally market driven and are highly competitive in today's marketplace. Long-term contracts, particularly those involving captive mines and mine-mouth power plants, are commonly driven by considerations other than economics. These other considerations, such as Reserve Conservation and Resource Recovery, Security of Supply, and Maintenance of Levelized Costs may increase the cost of coal, often needlessly and without benefit to the buyer or seller. The basic economic principles which guide the market driven metals industry and generally guide the spot coal sector of the coal industry should apply equally well to the long-term coal supply contract. The artificial constraints imposed as a result of regulated rates of return should be re-examined and in most cases, abandoned. There are many methods of surface and underground coal mining being used today such as, open-pit, contour, mountaintop, and area mining for surface mineable reserves; conventional, standard continuous and super-section continuous miners, and longwalls for deep reserves; and highwall miners, thin seam miners and augers in between. This discussion is primarily directed to surface mining, however the same principles of least cost mining on a Net Present Value basis must be considered in all cases.

Jan 1, 1994

By Malcolm T. Wane

The subject matter of this paper, "Applied Rock Mechanics?," has its genesis in a recent field trip taken by the author. A more or less standard question asked at the mines visited was "How are you using the principles of Rock Mechanics to assist you in maintaining an efficient, safe, and competitive mining operation?" The question was couched in a number of different forms, but the intent was to determine whether or not a general theory based on reason and the scientific method was applied or whether the alternatives of tradition, intuition, ?common sense', revelation, ?shotgun methods' or authoritarianism were invoked. Perhaps two responses to this query will be illustrative of the general nature of the replies. At operation XYZ an extension to the known ore body has been found. The extension is of large enough size and grade that a mining scheme using load-haul-damp techniques is envisaged. Since this represents a departure from the present mining scheme, questions have arisen regarding pillar sizes, room and entry sizes and possible support requirements. A task force has been set up to expeditiously plan for these things and write the necessary specifications and requirements. The fundamental question was posed to members of this group.

Jan 1, 1971

By D. R. Hembree

This paper discusses the mineralogy and metallurgy of the Kuroko-style volcanogenic massive sulfide ores mined at Formosa Exploration Inc. I s Silver Butte Mine located in southwest Oregon. The principle ore type is pyrite + chalcopyrite + sphalerite, while subsidiary pyrite + bornite + sphalerite ore is also mined. The two styles of mineralization have distinctly different metallurgical behaviors and must be treated separately. Selective flotation methods are used to produce copper and zinc concentrates from the first ore type, while bulk concentrates are produced from the bornite ore. Careful mine planning and coordination between the mine and mill are utilized to achieve optimal recoveries.

Jan 1, 1993

By J. D. McKay

Flotation columns have been readily accepted for use in most sulfide flotation plants; however, recently columns are being used in many other areas. Recent improvements in design methodologies have overcome many operating problems and led to improvements in metallurgy. In addition, physical improvements in column design have simplified their operation while leading to better control. The Turbo-Air External Bubble Generator has provided a method for bubble size control and variation in air holdup and carrying capacity. These have enabled commercial operations to improve grades and recoveries by optimizing performance.

Jan 1, 1990

By W. J. C. Meynink

In drier regions of the world, total containment of cyanide liquors for rainfalls less than a specific design value is often required by government regulation. For example, in Queensland total containment is required for rainfalls up to 'the 1% annual exceedence probability. In equatorial regions, where rainfall greatly exceeds evaporation, a total containment requirement is unrealistic and this is recognized by regulatory authorities. Regulatory constraints typically require that cyanide concentrations at an agreed downstream compliance point not exceed a specific value more than a specified fraction of the time. While the excessive rainfall prevents total containment, it does provide substantial dilution. This paper outlines a methodology for assessing the distribution of cyanide concentrations at a downstream compliance point in an equatorial region with limited hydrometeorological data. Consider the hypothetical mine environs depicted in Figure 1. The mine is located near the catchment divide and draws its water supply via a gravity line. Tailings from the process plant are piped to a tailings dam on a sub-catchment below the plant site. The objective is to determine the distributions of cyanide species concentrations at a compliance point just upstream of a major settlement to ensure they do not exceed regulatory limits.

Jan 1, 1991