Search Documents

By Howard J. Haselhuhn

The effectiveness of selective flocculation and dispersion processes for the concentration of hematite ore are strongly dependent on the ionic content of the process water. It has been noticed that magnesium ions are more detrimental to iron recoveries during gravity separation and flotation processes than calcium. This phenomenon was studied by measuring the zeta potential of hematite ore at various concentrations of sodium, magnesium, calcium, strontium and barium at a pH of 11. Results show that zeta potential inverts from negative to positive at concentrations as low as 0.16 mM of magnesium ions in the solution. It takes a significantly higher concentration (1.25 mM) of calcium ions to achieve the same effect. This difference is attributed to the ability of magnesium ions to adsorb to all surface hydroxyl groups, whereas calcium, due to its larger size, can only adsorb to every third hydroxyl group. This hypothesis was confirmed by results similar to those seen with calcium when this test was repeated with strontium and barium ions. The tendency for calcium ions to adsorb to every third surface hydroxyl group causes higher concentrations of calcium to be less detrimental to hematite concentration processes than magnesium.

May 1, 2012

By Rory P. A. Ball, Mark Briggs, Martin Dix

"Tunnel professionals should inform project stakeholders on the reality that tunnel projects are not 100 percent devoid of the need for excavations or public inconveniences during both design and construction phases. Competing stakeholder objectives to limit these disruptions must be weighed against the need to mitigate risks and to produce a constructible, operable and maintainable end product. Perhaps the approach we should take with stakeholders, also known as Authorities Having Jurisdiction (AHJs), is sharing memorable case studies that bring to life the potential risks so often buried within lengthy risk registers. This paper provides a sobering case study describing what can occur if the presence and/or location of utilities and other obstructions are not fully understood due to restrictions placed on exploration or mining operations. In this instance, the Microtunnel Tunnel Boring Machine (MTBM) encountered a buried concrete structure, followed by rows of abandoned wood piles, before finally colliding with an active high-pressure gas main under a bustling coastal highway. Multiple stakeholders imposed tight logistical and other work restrictions, compounding the difficulties experienced during the drive. However, the difficulties were effectively managed through the project team’s proactive collaboration and communication with everyone involved. INTRODUCTION Some of the most important decisions that influence the ultimate success or failure of a project may not be made by design engineers. Instead, these decisions are often made by project stakeholders and third-party agencies. Tasked with protecting the best interests of their users, these agencies are cautious of potential impacts associated with project construction and subsequent use. Unfortunately, actions required (or restricted) by stakeholders often result in unwanted ripple effects that negatively affect the very users they are trying to protect. For example, a mandate limiting a shaft site to an unreasonable size may be intended to reduce local business impacts, but may actually increase impacts as more supply and truck hauling is required."

Jan 1, 2016

By A. Tobey Yu

The smelter is the heart of a copper producing operation. Its principal function is to reduce and convert raw copper concentrates and/or leach plant precipitates into blister copper before it is refined. In addition to concentrates and precipitates, typical feed to a smelter also encompasses matte chips, flue dust, flux and lime. By nature, the characteristics of these materials are extremely variable, ranging from sub-micron to lumps, from slurry to dust, from abrasive to corrosive and free-flowing to adhesive. Furthermore, as a result of geological formation, most of the world's open pit copper mines are located in a semi-arid zone, where precipitation is minimal. This particular climate compounds the problem of handling these materials.

Jan 1, 1976

By S. D. F. Rocha, A. L. A. SANTOS, E. M. A. BECHELENI, R. M. Papini, P. R. M. Viana, F. P. C. Silvas

The kinetics of atmospheric sulfuric acid leaching from a Brazilian nickel laterite ore was assessed using distinct reducing agents and ore mineralogy. This transitional ore contains 1.63% Ni distributed as 1.27% in coarse size (− 500 + 150 μm), mainly as silicates (lizardite and chlorite—28.6%), and 2.06%in the fines fraction (− 75 μm), mainly as iron oxy-hydroxides (goethite and hematite—49%). The effects of temperature, acid concentration, reducing reagent type, and concentration were evaluated. The − 75 μm fraction limited the leaching efficiency and the use of reducing media with thiosulfate improved leaching and Ni-Fe selectivity. However, at constant Eh of 626–743 mV and a pH range between 0.2 and 1.1, no substantial rise in metals extraction, except for Co and Mn, has been observed. In order to determine the process control at 95 °C, two regions in the extraction curves were used in combination with the shrinking core model. Control by porous diffusion was observed and the kinetic constant was found to be in the order kFe<kNi<kMn<kCo<kMg for atmospheric leaching without Eh control. In reducing media for the first 15 min of leaching, the kinetic constant was found to be kFe<kNi<kMg≅kCo<kMn as derived from Ni disseminated into iron oxides structures.

Oct 7, 2020

By Jamal Rostami, Wei Hu

Efficient performance of EPB TBMs in clayey ground is primarily dominated by the flow capability of the excavated muck in the cutterhead and screw conveyor. Currently, Consistency Index approach is used to evaluate clay clogging potential, but it does not include the effects of surcharge pressure on clay behavior. In this paper, a macro-scale soil rheometer is introduced to assess the clogging potential under various water content and surcharge loading conditions. The results show that, in addition to water content, surcharge pressure has clear impact on clay clogging too. In practice, Consistency Index chart can be refined to incorporate the impact of face pressure to better simulate the EPB tunneling conditions.

Jun 13, 2021

By M. L. Matt

The Pittsburgh Safety and Health Technology Center of the Mine Safety and Health Administration has developed the Mine Emergency Responsiveness Development (MERD) program to improve the reaction and response of mine personnel in mine emergency situations. The MERD program simulates problems that may be encountered in underground mine fires, underground mine explosions or surface mine accidents. Since its inception in 1982, the MERD program has been presented to MSHA, Industry, Labor and State Government Personnel. The program is extremely versatile and is easily adapted to suit various training requirements. It gives the participants the opportunity to experience some of the emotions, frustrations and successes of a mine emergency in a controlled environment without having to be involved in one. Past participants have indicated that this training has better prepared them in actual emergency situations through increased awareness and advanced preparation of plans and resources. In 1992, a Mine Simulation Laboratory, which simulates a coal mine and metal/nonmetal mine, was built to improve training for mine emergencies and prevention and fighting of mine fires. This facility has been included in the MERD Program to provide realistic and practical training for mine rescue teams and MERD participants in advanced mine emergency operations. This paper presents an overview of the MERD program.

Jan 1, 1993

By M. C. Williams

As the flaws in the population balance model (PBM) comminution model are examined more deeply, further errors and problems were discovered. The Levenberg-Marquardt algorithm for systems of constrained non-linear equations was used to solve the dynamic PBM grinding equations to obtain the grinding selection and breakage rate functions. The fact that the PBM model equation Inverse Problem is degenerate or underspecified is demonstrated. Multiple solutions to the same PBM equations are provided. It is shown that there is no unique solution to the Inverse Problem unless additional constraints are provided or assumptions are made such as the Arbiter-Bhrany normalization assumption. The severity of the non-uniqueness problem for dynamic grinding is demonstrated. Each solution to a dynamic PBM, while giving the same prediction for a given grinding time interval, gives different solutions or predictions for mill composition for other grinding times. Actual experimental grinding data was assessed to determine the functionality of mill selection and breakage functions.

Jan 1, 1993

By E. E. Caba

Copper smelter flue dusts containing arsenic are hazardous materials requiring environmentally accept-able disposal, preferably with re-source recovery under the RCRA and CRCLA regulations. However, the known resource recovery processes entail capital and operating costs greater than can be justified by the revenue of the recovered metal. Consequently, the smelting industry is tending to forego resource recovery in favor of encapsulation and storage in a certified class I hazardous waste site, or in a dedicated facility located at the source Superfund site. Order of magnitude costs for this option with portland cement encapsulation are estimated at $100 per ton, not including transportation. Industrial adoption of a new resource recovery process re-quires that its cost, including capital amortization, exceed the cost of encapsulation and storage only by the amount of the offsetting revenue from sale of metal. The lime-roast/ammoniacal leaching process is expected to meet this goal.

Jan 1, 1992

By E. Forssberg

Studies have been carried out with the High Pressure Roller Mill, HPRM, to produce calcium carbonate minus 10 micron. This paper presents the optimization of the specific grinding force of the HPRM system for a maximum energy utilization when limestone is ground. In addition, experimental tests of producing carbonate minerals using the HPRM as a pre-crusher are described in this paper.

Jan 1, 1996

By A. W. Khair

Surface subsidence is a phenomenon mainly associated with longwall mining, although it can also occur if the coal pillar left to protect the surface deteriorates with time and results in the collapse of the room and pillar system. A method has been developed that utilizes physical mine models and laser holographic interferometry. This method is capable of measuring displacements as small as 5 micro- inches by means of generating displacement contours on a surface, even that of granular materials. Analysis of subsidence in room and pillar mining using models of various extraction ratios ad overburden depths along with two different types of overburden model material (sand and gelatin) has been made. The sand represented the extreme brittle conditions of geologic material while the gelatin represented visco-elastic behavior of geologic material. This paper deals with the analysis of data which has been gathered up to date, and mainly associated with the use of sand as an overburden model material. The analysis included the effect of variation of geometric parameters on surface subsidence. Among these parameters are: variation in seam depth and thickness, surface and seam inclination, and extraction ratio.

Jan 1, 1984

By E. Taskin

Diasporic bauxite from the Mugla-Milas region was mechanically activated in a planetary mill for different activation times and the structural changes were examined by X-ray diffraction analysis (XRD), scanning electron microscopy (SEM) and specific surface area analysis (BET ? Burnauer, Emmett and Teller). Non-activated and activated bauxite samples were leached directly in alkaline (Na2O) solution at atmospheric conditions and the activation procedure led to the amorphization and structural disordering of the diasporic bauxite structure, which increased the dissolution efficiency. Effects of milling speed, liquid/bauxite ratio and leaching time on alumina extraction in direct alkaline leaching of diasporic bauxite were also studied. The alumina extraction was ~7% for non-activated bauxite and ~70% for activated (75 minute) bauxite. Key words: Diasporic bauxite, Mechanical activation, Alkaline leaching, Alumina extraction

Jan 1, 2009

By Douglas J. Kramm

This paper discusses the history and development of the Rotary Kiln in improved fuel economy. It discusses latest technology to optimize fuel economy in a long Rotary Kiln. It discusses the limestone preheater, the SF process for cement manufacture, and the flash calciner with suspension preheat and. suspension deheat for fine limestone.

Jan 1, 1977

By Leonard Bronitsky

The construction mineral aggregates industry--the largest industry on a tonnage basis--is threatened with large shortages in the near future. Ironically, these common minerals which include sand, gravel, and stone are among the most plentiful in the earth&apos;s crust. However, as these minerals are low in value and used in large volumes, they are extremely sensitive to transport cost, e.g., a haul of 20 miles doubled the delivered cost of mineral aggregates. Consequently, these minerals must be located close to points of demand to have economic usefulness. But the development of new deposits is virtually impossible near many urban areas for legal, sociological and economic reasons. The spector of unfinished urban transport systems, curtailed residential construction, and a general deterioration of the physical urban plant, looms as a direct consequent of future mineral aggregate shortages in the U. S. metropolitan areas. The shortages of mineral aggregates in the Greater New York Metropolitan Area (G.N.Y.M.A.) are prototypical of the shortages faced by the U. S. Metropolitan areas. This paper presents an economic analysis of the consequences of not considering the broad aspects of conservation economics as a major component of resource management. The needless annual cost for the G.N.Y.M.A. is shown to be $30 million.

Jan 1, 1974

By J. Y. Hwang

Coal cleaning with traditional magnetic separation usually yields unsatisfactory results because minerals associated with coal, such as quartz, clay, pyrite and calcite, are weak-or non-magnetic. Magnetic reagent technology is a new mineral processing technology with the capability to enhance the magnetic property of minerals selectively. This reagent can be adsorbed selectively on minerals through the control of surface chemistry and, thus, result in selective magnetic enhancement. The application of this technology on coal cleaning has been experimentally demonstrated. Good separation results can be obtained at low to medium magnetic field strength. Comparison with other processing technologies is included.

Jan 1, 1992

By Graham Jones

During 1982 Ash Grove Cement Company contracted with Wagester, Walker, Thornton & Company to convert a Calcimatic rotating hearth kiln at its Portland, Oregon lime plant from gas/oil to coal firing. Increasing costs of natural gas and No. 6 fuel oil made this conversion mandatory if the plant was to remain competitive. Unique features of this project are 1) the distributors of pulverized coal to eighteen small burners around the inner and outer perimeters of the doughnut-shaped kiln, and 2) the attrition-dryer-pulverizer mill. Ash Grove, a century-old lime and cement producer headquartered in Overland Park, Kansas (Kansas City area), looked at various schemes for multiple burner firing before employing Wagester, Walker, Thornton & Company. W.W.T. of Pitts- burgh, Pennsylvania was formed in 1980 by acquiring the Solid Fuels Division of the Pullman Swindell Corporation. This division had been active in developing solid fuel firing for brick tunnel kilns, principally in the Southeast. They continue to supply such systems firing wood waste as well as coal to the brick industry and have also converted two Calcimatic lime kilns for Dixie Lime, Sumterville, Florida, a fluid bed calciner for Texas Gulf in Aurora, North Carolina, and a chrome concentrate kiln for Diamond Chemicals at Castle Hayne, North Carolina. Testing and a proposal have been made for INMETCO, Elwood City, Pennsylvania, on an annular hearth furnace for direct reduction of iron ore to metallic iron.

Jan 1, 1984

By R. K. Will

Granite Construction Company operates a rock quarry in the rugged Santa Cruz Mountains of central California indicated in Figure 1. Open pit methods are used to mine decomposed granite which is processed to produce sand, gravel, decorative rock and asphalt. The quarry is located near the village of Felton about five miles inland from the coast of the Pacific Ocean, and is near the campus of the University of California at Santa Cruz and several California State Parks. The area is heavily forested and is considered by residents to be environmentally sensitive. Because of the scenic beauty of the area and proximity to the San Francisco Bay area, a project such as a quarry receives the attention of regional residents and environmental organizations.

Jan 1, 1994

By George R. Powe

If Campbell County, Wyoming were an independent nation, it would rank fifth in the world among countries with known coal reserves. Only the United States, Russia, mainland China and West Germany would have greater volumes available. Not too many years ago that statement would not have seemed important, because oil and natural gas had become our nation&apos;s principal fuels. Western coal deposits, particularly those of the Powder River Basin in Montana and Wyoming, and which underlie virtually all of Campbell County, were largely unknown. But recently, in response to the three-pronged stimulus of vanishing gas reserves, rising petroleum prices, and clean environment statutes, these vast deposits have been delineated and have become, in the minds of many, indispensable to our goal of energy independence. Not only does western coal lie in thick seams near the surface where it can be mined in huge quantities at low cost, but also it possesses another coveted attribute in this age of environmentalism: low sulfur content. At Burlington Northern we count ourselves at the forefront of those who believe this coal is essential to any hope for the government&apos;s "Project Independence." But to that belief we add another article of faith. We are convinced the economics of unit train delivery of this incredibly immense resource make it the only transportation system that can help us achieve energy self-sufficiency in this country.

Jan 1, 1975

By F. J. Bruey

Refdist is a simple but valid approach to planning or analyzing a test-vs-control plant trial that uses accumulated plant performance data to calculate objective criteria for judging the trial outcome. Refdist calculations and results are explained and illustrated with data typical of the mining industry. Findings from a simulation study of Refdist statistical properties are reported. Suggestions for dealing with messy data situations are offered.

Jan 1, 1999

By A. Konya

"INTRODUCTION Underground Mining and Construction projects face several challenges unique to the underground environment compared to the surface environment. The goals of an effective blasting program are the development of a blast pattern that minimizes cost, maximizes face advance, and provides the desired fragmentation and face profile. In addition to these , mines must consider the very real operational problems that occur such as drill deviation, ground vibration, and deadpressing or sympathetic detonation of explosives. These operation problems lead to increased costs and decreased production in the mine, hurting the bottom line. Combined with these problems, underground blasts can be difficult to monitor and evaluate due to tight spaces, dust during the blast obscuring video, and the need to evacuate the immediate area with no clear line of sight to observe performance. This creates an environment which most mines know that blasting can be improved in their underground operations, yet most are hesitant to change due to fears of the shot freezing, misfires occurring, and questions about how to achieve a proper design. The explosive companies and shot service providers also offer limited assistance or knowledge in the underground blasting realm, unlike with surface blasting, leaving many underground operations in the dark. It is for these reasons that most underground operations are operating decades behind the current technologies and incurring significant costs, both real and hidden, from there blasting operations. This paper discusses philosophical changes to designs that need to be made for effective design and modifications of underground blast patterns to prevent deadpressing and precompression of modern explosive products (Konya, Konya, & Worsey, Modern Blasting Method Selection, 2017). While numerous different methods of underground heading development exist, there are two types that are used in a majority of mines around the world, these are the burn cut and the V-cut. The burn cut is a parallel cut that has holes that go straight into the face and are primarily used in smaller opening (due to ability to pull deep rounds with smaller room widths) and metal mines (helps in ore dilution and greater fragmentation). The V-Cut is a cut that uses angled drilling towards the center of the face (in the traditional method) and is primarily used in underground aggregate operations due to its cheap cost but larger fragmentation sizes and greater throw of the muckpile. This paper will discuss these two forms of cuts specifically with the understanding that modifications to these can be applied to other parallel and angled underground heading techniques. BURN CUT The burn cut is one of the older forms of underground blasting, where a part of the blast (burn) of a shot is heavily loaded with additional empty (relief) holes with the goal of smashing (aka burn) and pushing/blowing all the material in the burn out to provide relief for subsequent blastholes. The relief holes in the burn cut provide a parallel relief for the holes that are firing to break too creating a second plane of relief, however these are extremely small and can cause many problems if a design is improper."

Jan 1, 2018

"INTRODUCTION While the United States coal mining uses prescriptive regulation under the Title 30 Code of Federal Regulation enforced by the Mine Safety and Health Administration (MSHA), Australia uses a risk based approach. Australian regulation is individual to each state. In Queensland, Australia this risk based approach to address principal hazards is underwritten by the Queensland Coal Mining Safety and Health Act of 1999 and the Coal Mining Safety and Health Regulation of 2001. Each Queensland Mine is required to have an overarching Health Safety and Environment Management System, of which Safety Management Plans are an element. “Safety Management plans (SMP’s) are intended to formalise the process by which mines address principal hazards and other related matters to ensure the safety of mine personnel.”7 THE QUEENSLAND CONTEXT In Queensland, the basic elements of a coal mine’s safety and health management system must provide for risk identification and assessment, hazard analysis, hazard management and control, and the reporting and recording of relevant safety and health information and data.5 (Part 2 Division 1 Section 6(a-d)) The initial guidance for writing Safety Management Plans comes from the Approved Standard for Mine Safety Management Plans and Guidance Note QGN09- Reviewing the Effectiveness of Safety and Health Management Systems. The Guidance Note and Approved Standard are supplemental to the Act and Regulation, and put in place to provide more clarity around the topic. The definitions in this section come from the Approved Standard and are included to provide context for those who may not be familiar with Australian or Queensland law and regulation. A hazard is defined as a source of potential harm or a situation with a potential to cause loss, while a principal hazard is a hazard with a potential to cause multiple fatalities. A risk is the chance of something happening that will have an impact upon objectives which is measured in terms of consequences and likelihoods. It is important to be able to make the distinction between a hazard and a risk. For instance, a lion is a hazard, while the risk associated with a lion is getting eaten. As defined by the Queensland Approved Standard for Mine Safety Management Plans, a Safety Management Plan (SMP) requires a systematic definition of all the actions necessary to ensure that mining operations are carried out safely. A SMP includes, but is not limited to organisational structures, planning, activities, responsibilities, practices, risk identification, audits and reviews.7 The goal of a SMP management plans is to mitigate the risks to bring them to an As Low As Reasonably Achievable (ALARA) level."

Jan 1, 2016