Search Documents

By D. L. Romero

The Line Creek Mine is operated by Crows Nest Resources Limited, a wholly owned subsidiary of Shell Canada Resources Limited. It is located approximately 25 km north of Sparwood in southeast British Columbia (refer to figure 1). The Line Creek coal deposit is part of the Upper Elk Coalfield in the East Kootenays. The coal is a medium volatile, low sulfur, bituminous coal and is used as a coking coal. Coal close to the outcrop is typically of low F.S.I. and is processed for thermal use. The present pits have a total coal reserve of 30 million clean tonnes and is a multi-bench, open-pit operation. The coal is recovered by front shovel and backhoe combination, and hauled to the plant with a fleet of 120-tonne and 40-tonne capacity trucks. Line Creek is unique in that it can simultaneously treat both metallurgical and thermal coal in separate processing facilities (refer to figure 2). Run-of-mine coal is delivered to the truck dump. The plus 50 mm material is scalped off and reduced to minus 50 mm in two rotary breakers. The raw coal is then conveyed to one of five, 5000-tonne capacity, silos. Typically one silo is used for thermal coal and four for metallurgical coal (refer to figure 3).

Jan 1, 1991

The Sage Mill Project w approved by Santa Fe Pacific Gold Corporation's Board of Directors in October 1994. The Sage Mill Project included a pressure oxidation plant designed and constructed to process refractory carbonaceous ore using fine grinding/autoclaving technology developed specifically to treat Twin Creeks ore. The project was constructed in two phases. The first phase was put into operation on May 5, 1997, just hours before the transfer of ownership to Newmont Gold Company occurred. The second phase started in October 1997. This paper reviews schedule, costs, scope changes, and methodology used on the project that spanned almost five years from project definition through commercial operation.

Jan 1, 1999

By Frank F. Aplan, Robert S. Thomson

A placer ore jig, typically used to recover fine gold, tin and diamonds from alluvial ores, has been modified to remove fine pyrite from minus 6.4 mm (-114 inch) coal. In parallel tests, it proved to be far superior to two conventional coal jigs, the Baum and the Baum-feldspar, in removing fine pyrite from coal. The Pan-Am placer jig was found to remove essentially all of the +28 mesh pyrite and from 99% to 90%, decreasingly, in the 28 to 200 mesh range. This jig also showed a superior performance to the Baum-Type jigs in removing fine coal from its associated refuse. The superiority of the Pan-Am placer jig is related to the strong emphasis given on the suction stroke and, hence, on consolidation trickling, whereas the Baum jigs principally emphasize the pulsion stroke during jigging.

Jan 1, 1995

By T. W. Eddy

Research was conducted in which elemental mercury and its sulfide mineral (cinnabar) are removed from a copper sulfide concentrate by low temperature thermal applications. The goal of this research was to reduce, volatilize, and collect mercury vapor from concentrated smelter feed in a simulated drying environment while maintaining the chemical integrity of the residual. The study used synthesized concentrates composed of copper sulfide and mercury bearing minerals (such as cinnabar (HgS) or elemental mercury) to determine optimal residence times and temperature ranges.

Jan 1, 1996

By F. X. Meagher

Vertical slot raise driving from bottom up has always been a hazardous, inefficient, high cost operation. The introduction of the Simba 5 drill rig has enabled this type of raise to be drilled accurately from the top down and to be blasted in stages from the bottom up. Safety, high efficiency and low cost were the main criteria in opting for this method. Drop raises with the Simba 5 at Geco have been successfully drilled and blasted up to 115 feet, and this is close to the maximum length of raise that can be drilled and blasted efficiently with Simba 5. A look into the future would indicate a rig capable of drilling up to 200 foot raises with the same accuracy of Simba 5 to 115 feet.

Jan 1, 1974

By Adam Bezuijen, Tiago Gerheim Souza Dias

"The construction of mechanized tunnels in soft ground has evolved significantly over the last 20 years, especially in the control of the face pressure and the closure of the soil-lining void to reduce the induced settlements. On the other hand, several mechanisms of the TBM excavation cycle are still not taken into account for routine design calculations, such as the increment of water pressures in front of the tunnel face, the flow of excavation fluids around the shield, the dynamic equilibrium between the grout pressures and the excavation convergence, among others. This paper discusses specifically the issue of face pressures and how several mechanisms, which are routinely not considered, can be easily verified and incorporated into the state-of-practice of design. INTRODUCTION The stability of underground excavations is traditionally assessed through analytical solutions based on the lower bound theorem of plasticity (Atkinson and Potts 1977; Mühlhaus 1985) or the limit equilibrium method (Anagnostou and Kovári 1994; Messerli et al. 2010). These methodologies depend on the tunnel geometry, certain ground parameters and the support pressure. When conventional construction methods are used, the internal support pressure is an abstract representation of the combined effects of partial excavation, ground reinforcement, and the different support elements. The use of closed-face tunnel boring machines (TBM) changed this perspective, as the magnitude of pressures acting on the excavation boundary could be controlled in a more direct way. In front of the TBM the ground is excavated as the cutterhead rotates and the cutting tools scrape the ground from the tunnel face while additives are injected to condition the material. Water, polymers, bentonite, and foam can be used as additives under different conditions (Thewes et al. 2012). The loosened ground with additives, herein referred to as the mixture, flows through the openings at the cutterhead and into the excavation chamber. This mixture is kept pressurized to support the face."

Jan 1, 2016

By C. G. Anderson

Historically, the treatment of orebodies for recovery of valuable constituents presents many processing challenges. In a time of heightened environmental awareness, the constraints placed on processing complex orebodies are becoming more and more pronounced. As such, established technologies are limited in their ability to fill the needs of these emerging sources of raw materials. A prime example of this is in processing PGMs from primary sources. Normally, this type of material is found in a nickel-copper-iron sulfide matrix. Typically, these materials are processed by established pyrometallurgical means. However, other options should be considered. Hydrometallurgical processes are available which offer advantages over pyrometallurgical methods. One of these is the nitrogen species catalyzed sulfuric acid pressure leach used industrially by Sunshine Mining and Refining Company. In 1990, laboratory work was undertaken in cooperation with Stillwater Mining Company to test PGM matte materials from the Columbus, Montana smelter. The initial results were very positive, and they led to a design to recover PGMs in a high grade residue and to recover nickel and copper as valuable products. Handling the iron and other wastes in an environmentally safe manner was also successfully investigated.

Jan 1, 1995

By B. J. Timmons

Depending upon which of two letters describing the theme of the session I chose to honor, the subject choices because either one or three. They were: "Applied Research and Exploration and Discovery" or "Applied Research in Exploration and Discovery." The final choice; to partially ignore both of them. That minor difference in meaning may be appropriate here, inasmuch as very minor research/exploration differences may also have profound impacts on discovery. To further set the stage, I consider myself an Industrial Minerals geologist, and more specifically primarily associated with basic construction materials crushed stone and sand & gravel. My remarks will apply primarily to those materials. Therefore, when the discussion instructions included emphasis on beneficial aspects (to name a few): "drill target definition; elimination of ore potential; ore forming environments; alteration studies, and isotope analysis," problems became apparent. Evidently, and although this was a form letter, the drafters of that letter had no idea what was involved in research for a construction materials source. My task may be great.

Jan 1, 1995

By V. Svalbonas

When the Trelleborg Divisions of Boliden Allis and MPSI merged, a unique opportunity occurred for two independent mill fabricators to compare various design procedures and the research upon which they were based. This paper documents such a comparison in the structural design area. Several SAG mill analyses are compared using both Boliden Allis and MPSI methods. The differences and similarities are then utilized in a correlation of critical stress definitions and the acceptable design and inspection criteria.

Jan 1, 1992

A Mark IV surface force apparatus (SF A) was used to conduct direct force measurements in dodecylamine hydrogenchloride collector solution between mica surfaces at varying pHs. It has been found that the long-range hydrophobic forces reach a maximum at pH 9.5, which also corresponds to the maxima attained by the contact angle and flotation recovery of quartz. The charge densities are comparable on both mica and quartz surfaces (0.40-0.48 run2), making it possible to draw conclusions on the flotation of quartz from the direct force measurements conducted on mica. Therefore, it may be suggested that the maximum flotation recovery of quartz m the range of pH 8.0-10.3 may be attributed to the appearance of long-range hydrophobic force, which in turn can be related to the formation of a close-packed monolayer (or hemimicelle) in the presence of neutral amines formed as a result of hydrolysis.

Jan 1, 1996

By C. L. Lin

Linear grade distribution measurements determined from polished sections of randomly oriented particles can be used to estimate the extent of liberation for multiphase particles of specified size. Two techniques, optical image analysis and microprobe analysis, have been used to establish linear grade distributions. Both techniques were evaluated and compared using variable grade samples of products from a copper porphyry flotation circuit. The statistical significance of the linear grade distribution data obtained by optical image analysis was assessed. The average chalcopyrite content of these samples, as determined by chemical assay was used to estimate the variance of the experimental procedure. For a given accuracy, the number of particles required to obtain an unbiased representation of the sample was determined.

Jan 1, 1985

By I. J. Dowdeswell

Perspective Man is a model maker. Throughout recorded history man has-used models both to provide insights into the workings of the processes which surround him and as a step towards the eventual control of those processes. These models have covered the field from extremely large systems (solar and celestial. models) to infinitesimally small systems (sub-atomic .and atomic models). Models have been developed for social systems, ecological systems, biological systems and economic systems: all fields of human endeavour contain the fruits of this restless model-making. The Role of Models Since the evidence of mans' industry in formulating models is so abundant, it is worthwhile stating some of the reasons. Based on the simple definition that "a model is a convenient and useful representation of some facet of the 'real' world", then a model provides a means for: 1. Understanding the thing being studied. 2. Communicating that understanding to others. 3. Manipulating the thing being modelled. The common denominator implicit in these reasons is that- improved control is the. objective off all modelling or simulation work. Improved control shows itself either directly by the development of devices which perform the control functions or indirectly by improvement in the decision making process itself. For example, in a process plant, a suitable model of part of the process could lead either to the use of automatic control devices such as set-point controllers or to the implementation of instructions (pre-defined decisions) which permit the operator to better control the process. Typical process control systems use both of these since fully automatic control is restricted to processes where the required information can be effectively measured.

Jan 1, 1972

By B. I. Pålsson, H-Å. Häggblad, J. F. Stener, P. Jonsén

"Understanding mill charge motion is important. In the charge, the center of gravity is shifted from the rotational center of the mill system, and its motion is induced by rotation of the mill. At the same time, the charge creates a torque in the mill system. Breakage of ore particles and wear of liners/ball media are closely linked to this motion. To study these phenomena in a physically correct manner, numerical models for different parts of the mill system are needed. Validations of such models are scarce, because of the difficulty of measuring inside a tumbling mill. Experimental measurements in a lab mill were done for a number of load cases: varying feed material, mill filling, mill speed and pulp liquid. The mill is set up to measure the charge-induced torque. The accuracy is good, with relative uncertainty less than ± 2% for relevant load cases. A full three-dimensional numerical model of the whole mill is used to predict induced torque. Agreement between predicted and measured torque at steady-state is good. In addition, the model can accurately predict the mill startup behavior for torque and mill power. This proves that the model is physically correct, and can be used for modeling large-scale mills.IntroductionUnderstanding of the charge motion within the mill is of importance in mill optimization. The breakage of ore particles and the wear of liners/ball media are closely linked to the charge motion. To study these phenomena in a physically correct manner, appropriate numerical models for different parts of the mill system must be used. Validation of these models is of major importance. This has led to an increased interest in obtaining an accurate and direct measurement of mill load and the behavior of the mill charge.For structural analysis, the finite element method (FEM) is the most developed and most frequently used numerical method. FEM is a numerical solution method based on continuum mechanics modeling. A constitutive relation for the actual material is described, and the governing equations are solved in Zienkiewicz and Taylor (2000). Varieties of different constitutive models for a large number of materials are implemented in modern FEM code. The computability of nonlinear problems in solid mechanics is investigated in Belytschko and Mish (2001), among others."

Jan 1, 2015

By R. W. Draves

Planning and testing in advance of the mining operation are essential. This advance work can involve physical and chemical analysis of overburden cores, field test plots, green- house studies or any of a multitude of other baseline data collection activities. This paper presents the results of Central and South West's field test plots and how they relate to topsoil substitution. Besides the obvious need for testing in advance of mining, there are the inevitable regulatory requirements. Quoting from the office of Surface Mining Regulations concerning topsoil substitution: 216.22(e) TOPSOIL SUBSTITUTE AND SUPPLEMENTS -Selected overburden materials may be substituted for or used as a supplement to topsoil if the office determines that the resulting soil medium is equal to or more suitable for sustaining revegetation than is the available topsoil and the substitute material is the best available to support revegetation.

Jan 1, 1985

By S. G. Malghan, V. K. Pujari

Detailed characterization of all the powder constituents during powder processing is necessary for the reproducible manufacture of ceramic components that will perform reliably in intended applications. In this paper, selected physical and surface chemical techniques for characterization of silicon nitride powder are evaluated. The characterization data are discussed in the context of how these data, through their influence on powder processing unit operations, can affect the final microstructure. In the forming of ceramics, some of the major variables of injection molding are evaluated. Accurate measurement and control of these variables is emphasized for manufacture of Si3N4 ceramics with a high degree of reliability.

Jan 1, 1990

By John Ralston, Rossen Sedev, Nicola Richards, Quinn Anthony, Geoffrey Reynolds

Derivatised 2,4-diketopyrimidine groups have been anchored to planar gold surfaces as self¬-assembled monolayers (SAMs) for chemical and photochemical studies. Three derivatives, 5-methyluracil (thymine), 5-trifluoromethyluracil and 5-nitrouracil, were chosen for the specific moiety present at position C-5, which can exert strong or weak inductive effects on the adjacent aromatic ring. The measured acidity constants decrease from 5-methyluracil to 5-nitrouracil as the inductive properties of the group at C-5 position increase. When grafted to the surface the acidity constants increase, albeit still adhering to the expected inductive trend. The functionality also exerts an influence on the surface wetting properties. Surface wettabilities indicate that the orientation of the pyrimidine groups at the surface occurs so that the C-5 position has a direct effect upon the surface chemistry. Upon dimerisation the surface contact angles increase signifi¬cantly. At pH 11 the contact angle changes reflect that the dimer has a higher pKa than the monomer. The monomer surface is deprotonated at this pH while the dimer surface is partially deprotonated, leading to changes in contact angle of up to 22 degrees. Large changes in contact angle were observed for 5-nitrouracil which were independent of surface charge and were appar¬ently due to conformational changes alone. Electrowetting of three fluoropolymer surfaces by electrolyte solutions was studied with the sessile drop method. The electrowetting curve (contact angle/potential) is analogous to the elec¬trocapillary curve (surface tension/potential) and may be described by a combination of the Young and Lippmann equations. We demonstrate that for some specific surfaces a systematic deviation occurs at positive potentials. This departure is attributed to double layer effects, namely the adsorption of hydroxide and halide anions. pH, ionic strength and polymer composi¬tion can all influence electrowetting behaviour.

Jan 1, 2003

By Robert S. Foote

The U.S. Energy Research and Development Administration (ERDA) is currently conducting a national program to survey for uranium the conterminous United States and Alaska by 1980 using airborne and surface techniques. This paper discusses the techniques used and some of the results of airborne surveys conducted to date by Geodata International, Inc. Airborne gamma radiation and the earth's magnetic field data are measured to provide data leading to regions potentially more favorable for the exploration and discovery of uranium ore. High-sensitivity radiometric and magnetic field data have been gathered from an aircraft with an average surface altitude of 400 feet (Figure 1). Under most conditions, data are usable up to an aircraft surface elevation of about 1250 feet where limitations will be discussed. Results of data analysis under GJO-1632, GJ0-1644, GJO-1654 and GJO-1663 will be discussed.

Jan 1, 1976

By K. E. Laughery

The Nevada Barite industry has experienced a 277% growth over the last five years with a total production of 2,542,000 tons. Total production prior to 1970 approximates 2,700,000 tons dating back to 1907 Annual production, as can be seen in Table 1, has increased from 192,000 tons in 1971 to 723,000 tons in 1975. During this same period U.S production has increased from 825,000 tons to 1,056,000 tons. Nevada is now the leading producer with 69% of the market. The increase in the Nevada barite production is, of course, directly related to the increased demand for weight material coupled with the lack of other sources and the relative economic advantage of the Nevada barite, A significant tonnage of Nevada barite is utilized in the non-oil well market, principally at FMC's barite chemical plant at Modesto, California; however the growth has been in the oil well market.

Jan 1, 1976

By Mogens Henriksen

In the past decade, numerous urge scale drilling projects have made use of reverse circulation air lift methods. Reverse air lift pumping can be established by injecting gas into a column of liquid; the subsequently decreased density of the gas-liquid mixture allows atmospheric pressure outside the lift conduit to establish flow. The rate of flow can be controlled by varying the gas to liquid ratio. A typical reverse circulation air lift system is depicted in Figure 1. Allen1 has described a number of reverse air lift drilling projects. Although cited examples are generally related to large diameter holes, the method has seen use in other applications such as sand dredging, chemical pumping, water well pumping and continuous coring. One particular benefit obtained with enclosed reverse circulation drilling is elimination of lost circulation. The required air/water ratio for pumping at a given submergence and lift has been established experimentally by Gibbs2. His data, however, do not reflect sensitivity of flowrate to air/water ratio. Further, in Gibbs' work, air apparently is injected continuously along the column of water. This configuration differs from that used in reverse air lift drilling where air is injected at discrete points only. Gas lift theory has received considerable attention over the past decades. Orldszewski3 defined flow regimes in two phase flow. Griffith and Wallis4 determined relative velocities of gas to liquid. Two-phase flow has been studied extensively for oil transport in inclined and vertical pipes by Chierici et a15, Beggs and Brill6, and Gould, Tek and Katz.7

Jan 1, 1977

By R. Freer

Recent developments in expanded PTFE membrane filter cloths offer high flow rates and sub-micron particle removal. These high strength, industrial grade filter cloths can be tailored for tubular filters, leaf filters and rotary vacuum drums. Filtration techniques using tubular filters make possible filtration of difficult slurries with the elimination/reduction of filter aids and chemical additives. This paper describes principles of surface filtration, applying the membrane filter cloth and comparisons to gravity separators. Benefits to the mining industry include clear effluent, enhanced solids recovery and accelerated cost payback.

Jan 1, 1996