Search Documents

By K. Rajamani, I. Shah

The development of liquid-level control algorithms, based on sets of linguistic rules expressing human operator's "intuitive" control strategies, have been reported. The main objective of the present paper is to illustrate the implementation methodology. The experimental work was done with a 28.3Lflotation cell. The control variable (height of pulp in the cell) was controlled by manipulating the outflow rate. The controller algorithms were programmed and implemented using an Applelle computer and a Keithley das Series 500 measurement and control interface. It is pointed out that the scheme of fuzzy controllers is simple to use and powerful enough to handle complex and nonlinear systems.

Jan 1, 1987

By R. M. LaDouceur, C. A. Young, W. Nicholas

"Salicyl hydroxamic acid (SHA) adsorption on two rare earth oxides, lanthanum and yttrium, was studied. Adsorption at both surfaces occurred in two stages. Initially, the monovalent anionic collector appears to adsorb significantly and instantaneously in stage one and then becomes sluggish in stage two presumably because the initial stage passivated the surface. By comparison, adsorption during the sluggish second stage with lanthanum oxide did not stop but with yttrium oxide essentially stopped. Surface monolayer formation could not be observed in either of the two cases. Both stages appear to be due to multilayer formation of a surface precipitate as proven by Raman Spectroscopy for lanthanum oxide but inferred for yttrium oxide. Unlike the use of octyl hydroxamate as stated in the literature, increasing temperatures do not increase adsorption such that flotation of rare earths with SHA may be performed at room temperature leading to improved recoveries as well as significant energy savings. INTRODUCTION Rare Earth Elements (REEs) are comprised of the 15 lanthanides along with scandium and yttrium. The REEs with lower atomic numbers are relatively more abundant and are categorized as light REEs. On the contrary, the REEs with high atomic numbers are less abundant and referred to as heavy REEs. They are not really “rare” and, in fact, some of them are quite abundant in the Earth’s crust; it’s just that they “rarely” exist in concentrated deposits but rather are found dilute and practically everywhere. REEs share very similar physico-chemical properties but, because many of these properties are unique, they have gained enormous importance in recent times making several critical and strategic pending their use. For example, REEs have found extensive application in phosphor coatings, magnetics, and automobile cracking catalysts. Early technology was not advanced enough to produce commodity level production of the REEs and can be attributed to REE-bearing ores containing many rare earth minerals (REMs), not just one. In this regard, there are numerous REMs but bastnaesite, xenotime and monazite are considered to be the most common. Bastnaesite is a fluorocarbonate whereas the other two are phosphates. The separation of the individual REE-bearing minerals from the ores is not an easy task since they also exhibit very similar properties. Consequently, when flotation is used, it is done to produce bulk REM concentrates. For REM flotation, it is well established that octyl hydroxamate is more selective than fatty acid collectors (Pradip and Fuerstenau, 1983 and 1991). Liu et al. (2006) indicated that hydroxamates are the most common collectors for REMs. Pavez et al. (1996) studied the adsorption of oleic fatty acid and octyl hydroxamate on REM surfaces. Cui et al. (2012) studied the interaction of octyl hydroxamate with various REMs surfaces using various spectroscopic techniques such as XPS, FT-IR and Raman along with electron microscopy and concluded that such techniques offer ample information to establish adsorption mechanisms. Ren et al. (1997) studied napthalenic hydroxamic acid as a unique collector for flotation of REMs from bastnaesite ore and indicated that more selective collectors were needed. From these studies, it is clear that the quest of more selective collectors is essential but understanding how they adsorb at mineral surfaces is prerequisite to improving flotation performance."

Jan 1, 2016

By R. M. Kakwani

The filtration and dewatering results of -32 mesh Pittsburgh seam coal are discussed with reference to the microscopic structure parameters, i.e., particle segregation in the cake and particle and pore size distributions at different layers. At low solid concentration of 0.33 kg coal/kg water, a non-uniform cake structure is observed in which the particle and pore sizes increase from the top to bottom layers in the filter cake. An increase in the solid concentration in slurry produces more uniform cake structure and higher filtration and dewatering rates. Air bubble entrapment in the coal filter cakes is also discussed.

Jan 1, 1984

By Cyrus W. Field

Metalliferous sediments constitute an important component of the sedimentary veneer that overlies basaltic oceanic crust of the Nazca Plate and elsewhere. Although first collected more than one century ago near the East Pacific Rise during the Challenger Expedition and recognized for their anomalously high content of Fe and Mn, occurring as very fine-grained, yellow-orange, oxides, hydroxides, and oxyhydroxides, it was not until the more detailed studies of Bostrom and Peterson (1966) that their geologic significance and concentrations of other transition metals were fully appreciated. The Nazca Plate is a dynamic lithospheric unit bordered by the Peru-Chile trench and the East Pacific Rise to the east and west, and by the Galapagos Rift and the Chile Rise to the north and south (Fig. 1). Samples employed in this study were taken from piston core recovered from the Nazca Plate (Fig. 2), D. S. D. P. drill core from the northeast Pacific (Dymond and others, 1973), ferromanganese nodules from dredge-haul s at several locations, and from hydrothermal mineral deposits of the Andes. Our efforts have been largely sponsored by the National Science Foundation through its International Decade of Ocean Exploration Pro- gram. The metalliferous fraction of these sediments is widespread, but generally small. Sedimentation is dominated by biogenic silica in the equatorial latitudes, terrigenous debris adjacent to the South American Continent, and by biogenic carbonate elsewhere, except at depths below 3500 m in the central and northwest parts of the Nazca Plate near the East Pacific Rise. Contributions of these distinctive sediment types are shown by the distributions of Si02, A1203, and CaC03 given in Figure 3.

Jan 1, 1982

By Ned M. Smith

The Mississippian Salem Limestone, from which dimension stone is quarried in Indiana, is principally a calcarenitic rock formed of fossil bryozoans, echinoderms, and specimens of Endothyra. Numerical associations of the fossils, binding materials, oölitically coated fossils, and voids were determined by counting points on the surfaces of 278 thin sections of the limestone. Median sizes, coefficients of sorting, and skewness numbers were computed from measurements made of constituents in these thin sections. Many other samples and numerous exposures of the Salem and contiguous parts of adjacent formations also were studied. The organisms that furnished the skeletal material for formation of the Salem Limestone were chiefly gregarious and communal. Salem rocks are formed of nearly whole skeletons, of dismembered or slightly damaged skeletons, and of skeletons thoroughly ground up, because currents in the Salem sea varied in their ability to move and damage these materials. Locally the sediments are of uniform grain size because of sorting by currents and because related organisms grew to similar sizes. Rocks of the formation contain different proportions of the fauna both because the animals lived in these proportions and because their skeletons were mixed together by currents. The proportional relationships between members of the fauna were constant locally and for short periods of time. Study and mapping of the faunal associations, numbers of oölitically coated fossils, bedding structures, and size parameters enables geologists to suggest sedimentologic histories and sequences in areas of various sizes. Interpretations based upon such areal studies are necessary for evaluation of the dimension-stone potential within the Salem Limestone.

Jan 1, 1966

By Oscar H. Lentz

During 1960, the controversy over percentage depletion reached the level of debate between presidential candidates. Nixon took the position that he would not tamper with the status quo in this matter. Kennedy took the position that he was willing to take a fresh look at the issues involved. Kennedy's position appears to have been based upon two premises: (1) new sources of federal revenue may be needed; and (2) current depletion rates, even if sound in principle, may be too high and, therefore, inequitable. The latter premise constitutes the basis for the claims that depletion allowances are simply "loopholes" of tax avoidance. Very probably the controversy over percentage depletion will remain in the political limelight during most of the coming decade. It is quite possible that the current depletion rates, at least those for oil and gas, will be reduced during this period. The aim of this paper is to isolate the complex causes of this mounting opposition to percentage depletion.

Jan 1, 1961

By Stanley C. Suboleski, C. B. Manula

INTRODUCTION In any mining operation all possible steps should be taken to increase efficiency. One area for improvement is mine planning and design, particularly in the area of equipment selection for room-and-pillar systems. Be- cause of the availability of a wide variety of face machines, a fair degree of selectivity can be exercised in the choice of equipment for a particular job. However, this choice must be made on the basis of quantitative facts and forecasts related to the mining application. The purpose of this section is to develop and analyze the details of the mining process. Some specific areas studied include the relationship of system design to productivity, suboptimization as a result of equipment changes, and measurement of system performance. The plan of work leading to a quantitative description of these study areas is based on the growing interest in total system design using simulation as an analytical method (Manula, 1963). CHARACTERISTICS OF PRODUCTION OPERATIONS FROM ROOM-AND-PILLAR SECTIONS For a given mining method, raw production in a given section of a mine is primarily dependent upon the coal seam thickness, roof and floor conditions, methane emission, the mining methods, and the man-machine element. Average section production varies from 300 to 800 st per shift for conventional and continuous mining in high seams and from less than 100 to 300 st per shift in low seams. Since the reject varies from 0 to 40%, these figures must be decreased by the appropriate percentage to reflect the amount of clean coal mined. Personnel requirements per production section per shift for the various methods are listed in Table 1. Table 1. Production Personnel Method No. Method No. Conventional 12-1 5 Longwall 9-14 Continuous 9-1 2 Shortwall 9-12 MINING VARIABLES To evaluate the constraints and interrelationships for various mining methods, it is necessary to categorize the variables which underlie system production potential. Seven critical independent variables which determine production can be identified and categorized (Suboleski, 1978) : Seam Height The five categories are as follows: less than 36 in.;. 36 to 55 in.; 55 to 100 in.; 100 to 180 in.; and greater than 180 in. Floor Quality Floor quality ranges from : Excellent: Smooth, hard, grades less than 1 to 1 % % , and dry. Good: Smooth, soft but dry, with grades less than 3 % . The floor will deteriorate, but cautious operation can prevent it. There may possibly be heaving at some later time. Fair. Soft and damp. There is occasional interference with equipment operation; requires the use of four-wheel drive shuttle cars; ruts with regular use, and may have adverse grades of 5 to 7%. This may be coupled with slippery bottom and/or occasional steep rolls. Poor: Soft and wet. Requires blocking of the bottom to support equipment. There are frequent steep rolls and grades in excess of 7%. Roof Quality Roof quality ranges from : Excellent: Men are able to work under the unsupported top during the initial production cycle if legally permitted. Good: The roof is bolted on a 4 x 4 or 5 x 5 pattern with short bolts (442 in.) or <seam height if the seam >42 in., or requires posting with no bolts on a 4 x 4 or 5 x 5 pattern. There are no falls. Average: The roof is normally bolted on a 4 x 4 or 5 x 5 pattern, but with long bolts (>seam height or >6 ft.). There are infrequent minor falls or there may be an excellent roof which is difficult to drill. Fair: This type often requires spot bolting in addition to the regular pattern or bolting with planks. The roof conditions require shorter than planned cuts, or narrow cuts. Poor: This type requires bolts plus crossbars and posts, or installation of yielding supports or truss-type support. It is almost certain to fall if this is not done. Methane Liberation This ranges from none detected to low (no buildup at the face, even with minimum ventilation requirements) to moderate (the curtains must be extremely tight and tubing close to the face or methane will build up to 1 % during the loading of the car) to high (methane will build up to 170 if the miner is operated at the normal rate, even with proper ventilation). Hardness of Coal Coal hardness falls into the following categories: Soft: Soft coal is easily cut by a continuous miner. A plow could be used by longwall. Average: Coal of average hardness could be easily cut by a miner, and a shearer would be used in the longwall. Moderate: Moderately hard coal causes difficult cut-

Jan 1, 1982

By James K. Kindig

Hazen Research, Inc., has developed a new process for removing pyritic sulfur and ash from coal. Feed coal is contacted with iron carbonyl vapors, Fe(CO)5, at 190°C which puts a thin skin of magnetic material on the pyrite and ash, but does not affect the coal. Thus, low intensity magnetic separators yield a nonmagnetic coal, low in sulfur and ash, and a magnetic refuse, high in sulfur and ash. Results are given for clean coal produced by this method. A comparison is made between results of the magnetic process and the U. S. Bureau of Mines two-stage flotation process cleaning identical samples of Pittsburgh Coal. Capital and operating costs of the two cleaning methods are discussed.

Jan 1, 1976

By Stephen H. Hall

INTRODUCTION At some point in the design and development stage of a mineral venture, the assay laboratory building, its interior layout, and major pieces of analytical equipment must be specified for construction or purchase. Even the most experienced chemist would have difficulty in proposing useful specifications without a good deal of investigation into the kinds of analytical tasks that the laboratory will be expected to address, the probable workload, and the operating time constraints. This chapter will provide a logical approach to laboratory design that starts with such an investigation. Specific examples throughout the chapter are drawn from the author&apos;s tenure as Chief Chemist at Barrick Mercur Gold Mines, Mercur, Utah, from 1982 to 1985. It is necessary to understand the nature of a modern production laboratory, and to recognize that its operations bear more resemblance to its parent processing plant than to a research, teaching, or custom analytical laboratory. The assay lab is a processing facility unto itself, where samples and reagents are the raw materials, and assay results are the final product. Its most efficient operating mode is as an assembly line, treating samples in a nearly continuous flow. Nevertheless , there are important differences between the lab and the process plant. The products - assays - are individually unknown quantities until they are "produced.&apos; This can vastly complicate quality control compared to the process plant. Capital costs are general 1 y small compared to the plant, but the ratio of operating costs to capital costs for a laboratory is often very much higher than for the plant. This is due to the labor intensive nature of analytical work. For instance, during Fiscal Year 1984 at Barrick Mercur Gold Mines, labor costs for the laboratory staff represented about five percent of the total labor budget, while the laboratory building and equipment represented only about six-tenths of one percent of the original start-up capital. Failure to recognize both the similarities and differences between laboratory and plant operations is the foremost cause of difficulty encountered in designing a laboratory. The

Jan 1, 1986

By Irving Hoch

INTRODUCTION The demand for tunnelling can be related to urban population size and density; often, tunnelling occurs when a certain city size and density threshold is reached, and increases thereafter as a function of those population characteristics. Subways for rail mass transit are the most notable example, of course, but tunnels for water supply and perhaps for sewerage can also be related to size and density. As cities grow large they sometimes outgrow their local water supply and have to import water from distant places via tunnels; witness New York City, Los Angeles and San Francisco. And it has been suggested that Chicago use deep tunnels for storm water storage because tertiary treatment to meet water quality standards will require treating storm water runoff.(1) Other uses of underground space also increase with urban density, e.g., underground parking, concourses and shopping centers such as Rockefeller Center in New York City and the Place Ville-Marie in Montreal. These examples can be viewed as illustrative of the central point of urban land economics. As the number of people locating in a place increase, they bid up land values and make the more intensive use of land economic, with land defined to embrace the space both above and below the surface. Hence, we are led to think about the city, and of urban land use, in three dimensions. Now, if we accept the relation of underground space use to urban size and density, recent demographic trends seem anything but hopeful for future tunnelling demand: urban density is declining, population growth is slowing down generally, and there

Jan 1, 1974

By MANZOOR ALI BROHI, IZHAR MITHAL JISKANI, Atta Ur Rehman, SHUAI HAN, MUHAMMAD TARIQ, NIAZ MUHAMMAD SHAHANI

The analysis of mine safety indicators using a scientific method can improve mine safety and assist management in making informed decisions. This research establishes a mine safety evaluation index and proposes an integrative evaluation model based on the entropy weight and grey clustering methods. The index consists of 27 indicators classified into seven criteria: working environment (A), miners’ attributes (B), safety policies and education (E), prevention and control (F), and monitoring and supervision system (G). Using Pakistan’s mine safety situation as a case study, the proposed model categorized the indicators into five safety levels (very low, low, medium, high, very high) for the present situation and for their relevance in terms of future safety improvement. The results show all of the criteria falling into the very low level for the current mine safety situation. Three of the criteria — C, E and G — are identified as having very high levels of significance for future safety improvements.

By Miguel Reyes, Chenming Zhou, MATTHEW GIRMAN

This paper is aimed at helping the mining industry to better understand the challenges posed by electromagnetic interference (EMI) and to promote electromagnetic compatibility (EMC) in underground coal mines. The paper begins with a review of EMI standards in other industries, then presents some representative examples of EMI instances that have occurred in the mining industry, followed by a literature review of published EMI research in mining and, finally, a discussion on mitigation strategies and practical considerations related to EMI in mining.

Everyone knows the importance of careful handling of explosives. Even so, the point is on occasion all too graphically driven home. Witness the recent blast at a Utah explosives plant that killed five people. Part three of this series on explosives discusses transportation, storage, handling, and destruction. Federal, state, and sometimes local regulations govern the many steps involved in transporting, storing, and handling explosive materials. Regulations minimize personnel exposure to hazardous material and insure that the explosives remain stable and usable.

Jan 9, 1981

By M. Noppé

"Dilution in underground coal operations can be underestimated by up to five times during Feasibility Studies, with disastrous economic consequences. Every 1% of stone waste introduced can reduce an in situ specific energy of 11,000 BTU/lb (25 MJ/kg) by some 110 BTU/lb (0.25 MJ/kg) and increases the abrasiveness of the run-of-mine coal. Where a wash plant is not in place, penalties imposed for not meeting contractual specifications alone can amount to some AU$1 million per year.This paper presents a method for monitoring, reporting and ultimately controlling dilution in an underground coal mining operation. The dilution trends before and after introducing the recommended controls in a continuous miner/longwall mine are presented over an eight year period. The additional information from such a dilution monitoring program can also be used to control mining horizons and plan longwall extraction heights across the face proactively, on a short-term scale with resulting improvements in productivity. INTRODUCTION Grade control, as practiced on any mine, is concerned with predicting routine quality and tonnage values for short- to medium-term mining operations, and the reconciliation of these predictions against “actual” results. For a longwall mine supplying steam coal, such routine parameters may include the proximate analyses, specific energy (SE), abrasiveness and sulphur, as well as float and sink analyses if the coal is beneficiated. In addition, grade control is concerned with identifying the mineable horizon (or horizons) in a selective-mining operation, together with monitoring how well these horizons have been extracted or adhered to. Close-spaced surface drilling can be costly for any mining venture, particularly for longwall mines operating in the deeper seams. For this reason, much of the data for short-term grade control requirements are acquired during actual bord-and-pillar development. The underground data are derived from so-called “channel” samples. These samples are cut or chipped from the coal seam, perpendicular to the mining horizon, with dimensions suitable for obtaining sufficient “representative” sample for analyses. For a 2m thick mining horizon, a channel sample 300 mm wide and 50 mm deep over the thickness of the horizon would provide some 4.5 kg of sample, sufficient for most of the necessary tests. To allow the information to be computer recorded, additional information such as seam thickness, sample co-ordinates, and the elevation of the seam (or horizon) roof or floor, may be required."

Jan 1, 2015

Water contact angles in the air/water/francolite, fuel oil/water/francolite and fuel oil/water/quartz systems were measured to describe the wetting characteristics of these minerals. It was found that white francolite is more hydrophilic than black and tan francolite both in the absence and presence of fatty acid addition. The contact angle measurement results do not correlate very well with the flotation response and it appears that kinetic aspects of the bubble attachment process play an important role in the francolite-fatty acid flotation system.

Jan 1, 1997

By Ronald R. Bauer

Wollastonite is a little known industrial mineral of the silicate group. The largest and purest known deposit in the free world is being mined and beneficiated in Millsboro, New York by NYCO, A Division of Processed Minerals Incorporated. The associated garnet and diopside are separated from the wollastonite using dry high intensity magnetic separators. Beneficiated wollastonite is used extensively as an additive and filler in the ceramic, paint, refractory, and wallboard industries. Wollastonite acts as a functional filler due to its unique chemistry and physical acicularity.

Jan 1, 1982

By T. Hayashi

A sophisticated process of extracting ultrafine sulfide mineral particles of under 1µm size suspended in clay slurry has been developed through studies of electrochemical properties of particle surface. Experimental procedure and data of the process applied to some clay ores containing sphalerite and pyrite, and molybdenite and other sulfide minerals are reported. Discussions concentrated on the function of process reagents, particularly on various modifying reagents, and on the effect of dispersed or flocculated state of ultrafine particles in slurry which affect significantly the performance of the process.

Jan 1, 1982

By V. K. Gupta

A detailed laboratory study was carried out to investigate the effect of the particle size distribution on the grinding rate parameters, Si, for the dry ball milling of quartz and limestone. Contrary to the present belief, the Si values were found to vary strongly with the particle size distribution. In particular it was observed that: (i) the Si values increased with the fineness of the particulate charge - the increase being more pronounced in the case of the coarser sizes, (ii) the next finer size class had the maximum effect on the breakage of the particles of a given size class, while the coarser size classes had only a slight effect, (iii) the effect of two or more size classes was non-additive, and significant higher order inter-size interactions were indicated. The importance of these results in the context of the analysis, design and scale-up of the comminution systems is discussed.

Jan 1, 1987

By George W. Heunisch

The properties of Neutra-Fix® and Neutra-Ment® , two new lime substitutes for the treatment of acid mine drainage (Arm), have been compared with lime and Alkament®, two products presently in use for AMD treatment. The two new products are basically dolomitic byproducts and produce sludges that are more compact than those from lime. Sludge settling rates are faster than lime with iron concentrations after 24 hours that comply with EPA regulations. Material utilization and optimum pit are reported.

Jan 1, 1984

For all the attention given to mining activities in Central and South America, Mexico, Indonesia and Papua New Guinea, it is sometimes easy to forget the activities taking place in one of North America&apos;s most important and largely untapped regions -Alaska. The Alaskan minerals industry employed about 3,406 people during 1995. That is a 23% increase from - - 1994. It also contributed about $719.8 million to the state&apos;s economy during 1995, a 10% increase. During the past few years, Alaska has seen significant increases in exploration and mining activity. Fairbanks Mining, an arm of Cyprus Amax, began producing gold during 1996 at its Fort Knox Mine, as did Nevada Goldfields&apos; Nixon Fork gold mine. Kennecott&apos;s Greens Creek lead-silver-gold mine also reopened and USMX began operations at its Illinois Creek gold mine. In addition, several impressive exploration projects were under way in Alaska. Placer Dome reported good results at Donlin Creek project in southwest Alaska. Likewise, Newmont Exploration is getting serious about its True North gold project. And Nerox is nearing production at its Jonesville coal project in Alaska&apos;s interior. In November, about 400 miners gathered in Anchor- age for the Alaska Miners Convention. Throughout the conference and exhibition, attendees listened to updates on these precious- and base-metal and coal exploration and mining operations. They also learned that the state wants more miners to head north and help develop its natural resources. Alaska is ripe for a smelter The mining industry -Alaska&apos;s miners in particular - has a powerful ally in Sen. Frank Murkowski (R-AK). He is the chairman of the Senate Energy and Natural Resources Committee. During his luncheon address, Murkowski said it appears that it is economically feasible to extend the Alaska Railroad to northwest Alaska, taking advantage of the large coal and hard-rock mineral tracts in the Ambler mining district. He also renewed his push for building a major smelter in Alaska to process ore that would come from the Ambler mining district. Murkowski believes that Alaska&apos;s economy can be expanded by extending the railroad from Nenana to the Point Lay coal fields to open coal development. Along the way, the railroad would pass through the Ambler district, helping to develop the hard-rock deposits. An outgrowth of this additional mineral development, Murkowski said, could be a new smelter in Alaska. It could use power from the Tyee hydroelectric facility near Wrangell or from the Makushin geothermal project near Unalaska. Either site, he added, offers access to plentiful, relatively low-cost power, at tidewater to facilitate ore deliveries to the Pacific Rim. The Congressional Research Service has determined that there are enough mineral deposits and coal beds to make it possible to finance the extended railroad, he said. The 1,200-km (744- mile) rail extension would cost about $4.2 billion. The North Slope of Alaska contains up to 3.6 Tt (4 trillion st) of coal, Murkowski said, that contains less than 0.25% of sulfur and less than 4% moisture. It aver- ages 12,300 Btu in heat content. "That is a tremendous resource," he said. The Ambler mining district, meanwhile, has at least eight identifiable hard-rock deposits, Murkowski continued. These contain zinc, lead, copper, nickel, chromium, tin, barite, gold and silver. "All eight of these can generate ore concentrates at rates similar to Red Dog&apos;s cur- rent 725 ktla (800,000 stpy)" of zinc, he said.

Jan 1, 1997