Search Documents

By B. Weaver

Every year Pit & Quarry Magazine surveys the industry to produce their annual review. Here's a sampling of some of the statistics the survey produced from the end of the year 1994 survey.

Jan 1, 1995

By Thos. B. Douglas

In 1907, the Oklahoma Portland. Cement Company built a small dry process plant at Ada, Oklahoma, then Indian Territory. This plant was later acquired by the Ideal Cement Company of Denver, Colorado, who in 1918 built a new wet process plant along side the old dry plant. The older plant was later shut down .and eventually razed. In 1955, the Ideal Cement Company decided to increase the production at its Ada, Oklahoma operations. After many studies it was decided to build a complete new plant along side the old, near the site of the original 1907 plant. .The new plant was to have a. production of three million barrels annually while the plant then in. operation had an annual production of two and one quarter million barrels

Jan 1, 1961

By John L. Halls

Modern business practice dictates that in order to ensure the economic optimization of investment, the size of any investment venture must be such that every increment of capital invested in such a venture yields at least a corporate minimum acceptable rate of return. This practice is based on the premise that alternative investment opportunities capable of yielding the minimum corporate return are immediately available. If a mining corporation is to make the maximum use of its investment funds, any capital investment in a mining property must comply with the above practice. The most important parameter in estimating ore reserves is the cut-off grade which is used to separate material into ore or waste. The cut-off grade is calculated on the basis that material of cut-off grade produces sufficient revenue to cover the estimated costs of mining and processing through to sales, including depreciation and produce a pre-determined profit. Ore reserves so estimated are adequate for determining the magnitude of an orebody but do not provide a sound basis for determining plant size and therefore capital investment in a new property or for expansion consideration on an existing property. From a financial analysis of this one ore reserve it is impossible to ascertain whether each increment of capital investment is providing the minimum acceptable rate of return, Other difficulties associated with the calculation of a cut-off grade including the determination of depreciation and the amount of pre-determined profit to be included in the cut-off grade calculation are outlined in the text. The proposed solution to determine optimum ore reserves and plant size for new properties avoids the complication of calculating a cut-off grade by computing a series of ore inventories using arbitrarily selected cut-off grades. A comparison of the cash flows generated by production from such ore inventories using incremental financial analysis clearly indicates the ore reserve and plant size which will best serve the corporation's investment and metal production goals. Incremental financial analysis of a corporation's operating mines and prospects assists management in assessing the comparative expansion and investment possibilities of each property for increasing or maintaining metal production on a long term basis.

Jan 1, 1969

By J. Brune

The need for reliable and adaptable underground mine communications has become a focal point for both the safety and logistics of a mining operation. New mine communication technology aims to connect personnel, equipment, and data together while setting up a network that can be utilized during normal operations and also in an emergency event. The Mine Improvement and New Emergency Response Act of 2006 (also known as the MINER Act) requires mine operators to establish post-accident, two-way communication between underground and surface personnel and electronic tracking for all mine personnel. Communications systems must be designed such that they can survive major mine accidents, including explosions, fires, inundations and ground falls. Typical, wire-bound communication technologies are vulnerable because wires are often destroyed in such accidents. Wireless technologies that work well on the surface, such as cellular telephone networks; have limited applicability underground because the wireless signals do not propagate through rock.

Feb 23, 2014

By Adam Bedell, Jack Raymer, Brad Crenshaw

Tunnel contracts often include provisions for pre-excavation probing and grouting for areas ahead of the tunnel heading. If grouting triggers are met, tunneling stops, and grouting is performed. There is substantial variation within the underground industry on what criteria are applied to the grout verification hole that is drilled post-grouting and before excavation resumes. The criteria for determination of the effectiveness should be dependent on the geology and local hydrogeologic conditions. The purpose of this paper is to present specific criteria that can be used by a practitioner to determine whether tunneling can resume or if additional grouting is required.

Dec 1, 2022

By Robert M. Becker

The evaluation of in situ rock stresses from measurements of the change in diameter of a borehole that is stress-relieved by overcoring has become a common practice. Generally the stress evaluation has been based on isotropic relations whereas rock in varying degrees is anisotropic. A plane elasticity solution for a circular hole along one axis of an orthotropic medium has been adapted to evaluation of in situ stress. The necessary elastic parameters for this evaluation may conveniently be obtained from static tests on the overcore in conjunction with a consistent orthotropic thick-wall cylinder solution. The method and equations for the laboratory and field evaluations are summarized and illustrated.

Jan 1, 1968

By Dennis N. Poffenroth

One concern of the Mine Safety and Health Administration is the structural integrity of steel wire ropes used on mine personnel hoists and elevators. Failure of such ropes has resulted in loss of life and property. Although thorough and regular visual examinations are performed, hoist ropes may still fail from undetected internal wear, corrosion, and broken wires. To complement visual examinations, nondestructive rope inspection techniques have been developed to determine deterioration and removal criteria. The techniques use electromagnetic and permanent-magnet test instruments designed by a Canadian firm. This paper describes the operating principles, field and laboratory testing of these nondestructive testing instruments, and discusses the feasibility of using this type of testing as a supplement to visual examination and destructive tests.

Jan 1, 1982

By Simón Díaz-Quezada, HUMBERTO ESTAY

The heap leaching process has been widely used for recovering different metals since its first application at the end of the 1960s. In Chile, copper production via heap leaching has accounted for between 30 and 40% of annual copper production over the past 10 years. This level of production has been achieved through and supported by the use of a mathematical relation, known as the leaching ratio (LR) or irrigation ratio (IR), which relates operational parameters with metal extraction in a heap leaching operation. This ratio has been used to develop leaching column tests, to scale up results from the laboratory to industrial operations, to design new heap leaching plants, and in metallurgical control and production estimation. In spite of the widespread industrial use of this relation, few scientific studies mention it. This is due to its simplicity and basic theoretical foundations. This disparity between industrial practice and scientific research could lead to operational decisions which lack substantial theoretical support, and to scientific studies which have limited industrial impact. Against this background, several questions arise about the use of the LR: What are the constraints on the use of the LR? Are there practical advantages with respect to reported kinetic models? What is the main reason that industry prefers the use of the LR over kinetic models, which enjoy greater theoretical support? In order to guide its future use, this paper describes the leaching ratio and its current uses and limitations, through a literature review and case studies.

May 2, 2020

By G. V. Henderson

The San Gabriel Valley contains some of the richest and most extensive sand and gravel deposits in California. Operating quarries within the San Gabriel area mine more than 15 million tons of high quality aggregate per year. This represents about 45 percent of the total mined in the greater Los Angeles area, one of the nation's largest aggregate markets and producing regions. Popular opposition to continued aggregate production in the San Gabriel Valley is high, especially in the city of Irwindale where 40 per-cent of the city's property is made up of "excavated holes," some 150-200 feet deep. Reclamation of 70 years of mining is now an almost impossible task. Zoning regulations have the effect of depleting these vast reserves rapidly by changing the definition of total reserves to include only "legally minable reserves." All but two or three of the aggregate mines now operating will be depleted or zoned out of business by the year 2000. Some studies indicate that there will be no aggregate mining operations by 1995. Recent studies show a drastic change in land use patterns within this valuable mineral resource area over the past 20 years. The San Gabriel Valley is a classic example of the lack of adequate regional planning with regard to urban development in MRA's and represents a "too little, too late" effort by local government and industry.

Jan 1, 1978

By William Gleason

"What will the mine of the future look like? Will it resemble the current operations that supply the world with the products it needs to function, or will it be something totally different? How will the demands from the communities that are most affected by mining operations shape the mine of the future? How will technology and innovation be used to help miners reach deposits that are getting harder to access, and what are the dangers of this new world? Who will work at the mine of the future, and what will that work look like?These are questions that do not yet have definitive answers, but they are questions that need to be asked for the mining industry to move into a future that is as filled with uncertainty and challenge as it is with promise and opportunity.On Feb. 16, the 2015 SME Annual Conference and Expo and the 117th CMA National Western Mining Association conference began with a keynote address, "The mine of the future: Forecasting opportunities and challenges for the global mining industry." Panelists from five sectors of the mining industry participated in the session, which was followed by the conference and expo, that in large part, were also trying to answer the question of what the mine of the future will look like.In coming months, Mining Engineering will continue the discussions and answer some of the questions submitted by members of the 2,000-person audience during the keynote address in a monthly feature called, "Predicting the Mine of the Future," and in Thought Leaders Podcasts with the panelists and other industry experts."

Jan 1, 2014

By C. Salcedo, J. Vallance, J. Sáez, M. Robles, J. Spangenberg, S. Rosas, L. Fontboté

The Tambomachay ore deposit (13°28'36.78"S, 71°57'35.98"W, about 6 km north of the town of Cuzco, Peru) consists of Cu hosted in arkosic red beds of the Kayra Formation (Lower Eocene). Bornite, chalcopyrite, chalcocite, covelite, digenite, malachite, and chrysocolla occur disseminated in thin layers and in veinlets. The occurrence of the copper ores in a part of the red bed sequence containing green reducing layers, the presence of organic matter in interstices between the hypogene sulfides, and the sulfur composition of the copper sulfides (δ34S values between -16.9 and -12.4‰ vs VCDT) pointing to bacterial sulfate reduction, are strong arguments to propose that mineralization was caused by copper-bearing oxidizing saline basinal fluids that precipitate copper sulfides when they meet reduced sulfur in an organic matter-rich horizon. Faults parallel to the regional Tambomachay Fault could have acted as feeders for oxidizing basinal copper-bearing fluids. Fluid migration was probably driven by tectonically-induced topography gradient. INTRODUCTION A number of red bed Cu occurrences are known in the Cuzco region in the early Eocene – early Oligocene San Jerónimo Group (Gregory, 1916; Carlotto et al., 1996, 2011; Loza et al., 2004). In the past, copper ores were extracted in several small-scale mines in the surroundings of Cuzco, including Tambomachay, Tipón, and Zurite in the Cusco province and Ushpa, Guilda, Giovanna, and Langui in the Sicuani Province. The abandoned Tambomachay Mine (13°28'36.78"S, 71°57'35.98"W), about 6 km to the north of the town of Cuzco (Romero et al., 2015; Salcedo et al., 2017, Fig. 1) was chosen as the main site for the present research aimed to better study the genesis of these copper occurrences. Results deriving from fieldwork, microscopic characterization of ore and host rock, and sulfur isotope determination suggest that the key factor for the genesis of the copper ores is that copper transported by oxidizing basinal fluids is trapped by reduced sulfur of bacteriogenic origin located in a part of the red bed sequence that shows intercalatins of green reduced horizons.

Jan 1, 2019

By S. S. Peng

A well designed mining plan is one which minimizes the cost and the mining induced problems and maximizes the recovery of the coal reserve. In order to minimize the negative effects on surface structures caused by ground subsidence process due to underground mining activities, two kinds of practices are commonly employed by the mine operators. One is the support techniques which leaves an area of coal un-mined or partially mined beneath the structure to be supported. The other is the protection techniques which protect the structure when it is subsiding with ground taking advantage of the ground subsidence process (Luo et al., 1992). In designing the supporting techniques, the only currently available method in the U.S. is the one stated in the Pennsylvania Underground Coal Mining Rules (1985). However; The size of the support area designed by this method will be excessively large resulting in wasteful use of coal reserve when the overburden depth is more than 350 ft. A more scientific method is proposed in this paper for de-signing the support area. This method is based on a large amount of subsidence data collected throughout a number of major U.S. coal fields and the authors' experience with monitoring and protecting surface structures undermined by longwall panels. It considers the critical deformation in-dices that a structure can tolerate, and depth and height of underground extraction. The support area designed by this new method will not only assure the safety of the structure to be supported but also maximize the extraction of the coal reserve.

Jan 1, 1993

By Tony Walsh

Australian Stock Exchange Limited (ASX) -ASX is ranked 9th in the Morgan Stanley Capital International (MSCI) Index – only 2.02% of that Index. -1520 companies – 400+ mining & mining exploration. -Over 50% of Australians own shares in ASX listed co.s -Disclosure standards play a vital part in providing investors with confidence, thereby building depth and liquidity in the market.

Jan 1, 2003

By D. A. Lowrie

Environmental concerns and increasing mine development costs have created a need for early information on gold recovery from its host environment. The habit, association, and approximate abundance of minerals which contain unacceptable metallic ions which may be released during process of concentration of gold should be identified in exploration drill core. One case of a "clean" gold orebody is described to show that early petrographic studies contributed to a rapid decision to mine a small deposit by open pit and to custom mill the ore in an already restricted effluent environment. A second example describes identification of an undesirable mercury content and resulting action taken.

Jan 1, 1985

This paper examines the feasibility of combining network modeling and computational fluid dynamics for modeling of underground mine ventilation systems. Both simulation methods have specific advantages and disadvantages for analysis of mine systems. Network modeling is widely utilized by many operations and allows for assessment of current systems and simulation for planning purposes. Alternatively, CFD has been utilized only marginally by operations and is typically a research tool, requiring considerable computational power, complex models, and careful analysis and calibration of results. Network modeling allows for a holistic approach to the ventilation system, giving quantity, velocity and pressure in every branch, but CFD modeling can resolve the flow regime in 2-D or 3-D, which is idea when examination of an area on a more detailed basis is useful, such as dust and gas control. Integration of the two can allow for more flexible systems analysis. The feasibility of integration, along with application to limited underground mine data are examined.

Feb 23, 2014

By James E. Lonergan

Linear goal programming is a multi-objective optimization technique where the constraints of a linear programming formulation of a problem are considered as additional objectives. The optimal solution is the one that comes closest to satisfying all the objectives. An interactive computer program was written to utilize this technique in solving the feed blending problem faced by power plants de- pendent on multiple sources of coal supply. This program determines the amount of coal from each supplier to utilize in the blend. Examples of the use of the program in both long and short term coal procurement planning scenarios are given.

Jan 1, 1984

By M. N. Chandraprabha

This paper discusses the role of the mineral-adapted acidiphilic microorganism Acidithiobacillus ferrooxidans in the beneficiation of arsenopyrite-containing multisulfides (pyrite and chalcopyrite) and the bioremediation of the resulting arsenical waste water. It was found that adaptation to minerals alters the surface properties of the microorganism. Bacterial adaptation to arsenopyrite and controlled bacterial adhesion to mineral surfaces lead to selectivity in arsenopyrite separation. Bioremoval of arsenic ions (both arsenite and arsenate ions) by Acidithiobacillus ferrooxidans is also discussed. Key words: Acidithiobacillus ferrooxidans, Bioremediation, Arsenopyrite beneficiation

Jan 1, 2009

By Nikhil Dhawan, Sanjay Pindar

The limited lifespan, ever-growing demand, and significant lithium and cobalt content are responsible factors for the immediate recycling of discarded lithium-ion batteries. Discharged batteries were dismantled, segregated, and size reduced to recover cathode and anode material. The active cathode material comprises LiCoO2 (65.8%) and LiMn2O4 (34.2%) and was carbothermal reduced with recovered graphite in a microwave furnace followed by water leaching and magnetic separation. A Box Behnken statistical experimental design is used for process optimization. Both cobalt and manganese report to magnetic fraction, whereas graphite and lithium carbonate report to non-magnetic fraction and solution crystal respectively. The final product comprises of cobalt 73% and manganese of 14% with process yield of 36% and saturation magnetization of 76 emu/g.

May 16, 2020

By Y. J. Wang

The Hardy Cross iterative method is the most popular technique for solving a ventilation network problem with natural air splitting. This method tradition-ally solves each mesh equation by an approximation during each iteration. It is thus interesting from both theoretical and computational viewpoints to be able to solve for an exact solution to the mesh equation. Presented in this paper is an algorithm for computing the exact solution to the mesh equation with a variable fan pressure. The algorithm uses signum functions for air quantities to generate an alternative mesh equation in the form of a quadratic equation, which has two solutions defined by the well-known quadratic formula. The condition that the derivatives of the alternative and the original equations must be the same provides a basis for the correct choice between the two solutions.

Jan 1, 1997

By T. N. Moore, E. M. De Souza

J. Dasher Regarding the March 1991 ME technical paper by De Souza and Moore: For more than a decade since my February 1981 article on how to use modern metric, which SME-AIME had decided to do, I have monthly pointed out metric errors to the editors. In part, I do this because there has been no action to allow editors to fix figures and tables or to allow them to require authors to do so. The latest resulting atrocity provokes this discussion of vibrating drill handle units being stated in decibels. Reply by T. Moore We have read the discussion of our paper by Mr. Dasher. Our reaction is one of surprise and incredulity. It would seem that Mr. Dasher takes exception to the use of the decibel scale to present vibration acceleration data, and the use of hertz as the unit for frequency. The basis for his objection to the decibel appears to be that it has no dimensions (which somehow invalidates its use), that it is "non-metric" and, finally, that it is parochial (of limited or narrow scope). His objection to the use of the term hertz is not stated, but we will assume that it stands condemned as "non-metric" and parochial. Obviously we disagree with Mr. Dasher's views and will now outline our reasons. Although the decibel scale originates from transmission line theory and telephone engineering, it is also at present widely used, not only in the fields of electronic engineering and acoustics, but also in the area of vibration. The original definition of the decibel (dB) was based on power ratios: dB = 10 log 10(W/W0) where Wo is a reference power. However, as the power measured across a given impedance is related to the square of the force acting upon this impedance, Z, a more commonly used definition is: [2 dB = 10 logF /Z) = 20 log F/F 10\ F0 2 /Z(0)] where F and F0 are the r.m.s. values of the forces. Now, if the measurements are related to one and the same impedance, the decibel notation in the form of 20log10(X/Xo) may be used as a convenient relative magnitude scale for a variety of quantities. Thus, X may, for instance, be an r.m.s. displacement, velocity or acceleration. It is only required that XD always be a reference quantity of the same type as X. That is, when X represents an acceleration, then X0 represents a reference acceleration. This is the formulation used in our paper. This was not an arbitrary choice on our behalf but reflects standard practice as specified in the International Standard ISO 5349-1986(E) Mechanical Vibration - Guidelines for the Measurement and the Assessment of Human Despite the metric prefix, the decibel is a parochial expression of (l) the logarithmic ratio of the loudness of a sound to what is normally audible or (2) the logarithmic ratio of two power signals in radio or electronics. A decibel is not a unit, much less an SI, unit and has nothing whatsoever to do with the acceleration of drill handles. Stating that m/s2 (acceleration) is decibels is without reason. Whoever reviewed this material should not have allowed publication of figures of dB and H.[ ] Exposure to Hand-Transmitted Vibration. This was clearly stated in the "measurement protocol" section of our paper. This quantity is then referred to as the acceleration level and is expressed in dB. We may have inadvertently caused some confusion when we simply used the term acceleration to refer to acceleration level on our diagrams. At the time, we felt the use of dB or m/s2 would make the context clear to the reader. For any confusion this decision may have engendered, we apologize. Since the decibel expresses the ratio of two like quantities, it certainly has no dimensions. It is, however, common practice to treat "decibel" as a unit as, for example, in the sentence, "The acceleration level measured at the operator's hand was 160 dB." The expression of measured quantities in dimensionless form is not inherently unacceptable. In fact, in many areas of engineering it is standard practice (consider the use of Reynolds Number, Nusselt Number, etc.). The fact that the decibel is a dimensionless quantity makes the question of whether it is a SI unit nonsensical. However, it is valid to insist that the dimensional quantities used to obtain the decibel values be expressed in SI units. A careful reading of our paper will make it clear that the measured acceleration was, in fact, expressed in units of m/s2 as was the reference acceleration (l x 10-6 m/S2). These are the accepted derived SI units for acceleration. See, for example, the standard ASTM E380-89a Standard Practice for Use of the International System of Units (SI) (The Modernized Metric System). Concerning Mr. Dasher's implication that hertz (Hz) is an unacceptable unit of measure for frequency, we would again refer him to the standard ASTM E380-89a. Here, he will find (section 2.4.2) that hertz is an accepted "special name" for the derived SI units-1. This is in keeping with numerous other international standards including ISO 5349-1986(E) to which we referred in our paper. In conclusion, we agree with Mr. Dasher on the desirability of expressing measurements in modern SI units. But we would remind him that the standards that define the use of these units, and the accepted means of presenting measured data, are in a continual state of refinement. It is, therefore, incumbent upon him to keep abreast of these changes if he wishes to constructively critique the work of others.[ ]

Jan 1, 1992