Search Documents

By K. W. Grubaugh

The recently enacted federal surface mine law (P.L. 95-87) will increase further the complexity of securing a reclamation permit. This law intensifies the need to present the required reclamation plan in a thorough and comprehensive manner. One plan format, that used in construction performance contracts, offers promise of filling this need. Reasons for using the format of expressed, bilateral, negotiated contracts common to the contruction industry, and the salient aspects of an application which uses this format are reviewed. Advantages of this procedure are seen to be improved mine planning, awareness of the total design job, potential for improved speed of permit acceptance and improved cost control.

Jan 1, 1978

By Emmanuel V. Manlapig

The variables involved in a complex process like flotation can be classified as follows: a. Disturbance variables - which are undesired properties of the process input which affect the value of the process output but which are not subject to adjustment. They are the result of changes in the properties of the feed, like changes in head grade, flow rate, fineness of grind, etc. b. Manipulated variables (sometimes referred to as process variables or control variables) -which are those that are adjusted - reagent addition, aeration, pulp level - in order to compensate for the disturbances in the properties of feed. c. Performance variables (sometimes referred to as controlled variables) -which are those whose values measure the performance of the process. They are properties of the process output such as grade and recovery. The function of a control system is to maintain the process performance equal to the control objective in spite of the disturbances by adjusting the manipulated variables. Attempts at developing automatic control systems for mineral processing operations date back to the thirties and in many of these attempts the results were not surprisingly poor and un-stable. The poor results brought indifference and suspicion towards automatic control on the part of operators and management. The reasons for the apparent failure of these attempts were two-fold: a. the lack of adequate understanding of the behavioural responses of the process from the control point of view, and b. the lack of reliable control instrumentation which could withstand the harsh environment in mineral dressing plants. Many operators had accepted the fact that control of mineral dressing could be best conducted manually. In the case of flotation circuits, control had been virtually based on the skill and experience of operators particularly their ability to identify and rectify poor flotation performance aided by results from the laboratory (chemical) analysis of regularly collected samples from strategic points in the circuit which are at best, hourly collected samples.

Jan 1, 1978

By K. R. Griffin

New and developing communication systems enable underground miners to not only connect to the surface from an increased communication coverage area but also to be discovered in the event of an emergency. Communication and tracking systems are required by MSHA regulations, aiming to enhance health and safety and routine production in underground operations. Modeling a mine?s potential communication coverage area will increase overall coverage and efficiency of the communication network itself. Modeling the propagation of wireless communications enables ideal broadcast locations to be found when designing a communications network. Strategic placement of broadcast devices results in a reliable communication network that can better withstand disruption in both daily operation and emergencies. This paper will discuss recent regulatory developments in underground coal communication systems, the implementation of these new technologies, and how communication system?s networks can be modeled and analyzed using computer simulations.

Jan 1, 2010

By T. R. Hughes

How do you fit a processing plant underground with minimal change to mine infrastructure and yet maintain economic recovery, operability and maintainability? By combining fine crushing, continuous-gravity recovery and flotation. A modular, transportable processing plant has been designed that is capable of being installed in underground drives/drifts or on the surface. The Python processing plants have been designed to treat 20 or 50 tons per hour of ore to a particle size of approximately 500 µm and recover gold and sulfides into the concentrate. The plant is only three meters wide (including bolt-on platforms) and can be installed on a 1:50 slope, making for very simple installation. Test work carried out by Gekko Systems Pty. Ltd. has indicated that up to 50% of ores tested to date would achieve gold recovery rates of over 90% using this method. The projected benefits of this strategy are numerous and include low overall capital and operating cost, significantly less power consumption compared with traditional milling circuits and low environmental footprint.

Jan 1, 2010

By John D. Price

The solution to the problem expressed in the title of this paper might well be condensed into one word, AUTOMATON, But if I were to stop there, even though most of you might applaud, I am afraid that a one-word paper might not justify my coming to this meeting, So let?s explore the matter and try to learn if and to what extent the science of automaton can be applied to the problem of coal cleaning. In taking this approach we must, of course, by-pass the fact that plants In this Country and aborad have been automated to a greater or lesser extent. We will explore the matter from the beginning and not merely take the approach that because others have done it we can do it also. First, let us see just what is meant by automaton.

Jan 1, 1959

The effects of additives, sodium hydroxide, sodium carbonate, sodium oleate, oleic acid and polyacrylic acid, on stirred media milling of limestone have been investigated. The results are evaluated in terms of specific surface area, specific energy and energy efficiency as a function of additive dosage, polymer molecular weight, solids concentration and relevant operating variables. Use of additives generally results in changes in specific surface area and energy efficiency, while under certain conditions a more than 100% increase in these parameters can occur. Relevant interfacial properties have been measured and milling mechanisms involved are explored particularly in terms of the effect of additives on the flow patterns at higher solids concentration.

Jan 1, 1996

By A. Singh, C. Da Corte

"South Africa possess the biggest fluorspar reserves in the world followed closely by China. In light of the current commodity downturn this paper explores the use of Dense Media Separation (DMS) as a coarse pre-concentration method for two fluorspar deposits located in South Africa in which the dominant gangue is carbonate present in the form of dolomite and calcite. Heavy Liquid Separation indicated that conventional pre-concentration of the drill core samples from both deposits would result in unacceptably high fluorite CaF2 losses. At a maximum CaF2 loss to floats of 5% the benefit of DMS would be economically marginal and difficult to justify as a conventional pre-concentrator. In light of cashflow constraints, a twin flowsheet was proposed for the sole purposes of upfront cash generation in which the majority (67-77%) of the CaF2 would report to a high grade flotation plant in 38-41% of the mass whilst the rejects would be stockpiled for flotation at a later stage. Considering the proposed twin flowsheet approach the high grade product split was achieved using DMS and this paper documents the challenges encountered and results achieved. INTRODUCTION Fluorspar is the commercial term for the mineral fluorite (calcium fluoride, CaF2). Worldwide production of fluorspar is dominated by four countries namely China, Mexico, Mongolia and South Africa. Although South Africa is the fourth largest producer, it has the largest fluorspar reserves closely followed by China (U.S. Geological Survey, 2017a). Fluorspar is broadly categorized into two grades namely acid grade also referred to as acidspar (>97% CaF2); and sub-acid grade (ceramic and metallurgical grade) commonly referred to as metspar (=97% CaF2). Acid grade fluorspar is used for the production of hydrofluoric acid (HF) which in turn is used for the manufacture of fluorocarbons and semi-conductors in the electronics industry; metal processing; the production of insecticides, herbicides and cleaning detergents, and the manufacture of uranium tetrafluoride used to concentrate the uranium isotope 235 for use as a nuclear fuel (British Geological Survey 2010; Miller 2001). Ceramic grade fluorspar (85-95% CaF2) is used in the ceramic industry as a flux and opacifier in the production of glass and enamels. Ceramic grade fluorspar is also used to make coatings for welding rods and as a flux in the steel industry. Metallurgical grade fluorspar (60-85% CaF2) is primarily used in the steel industry as flux to reduce the melting temperature and remove impurities in steel making. Similarly metallurgical grade fluorspar is also used as flux in cement production to reduce energy consumption (British Geological Survey 2010; Miller 2001)."

Jan 1, 2018

By W. C. Meyer

The concept of using powdered coal-in-oil-mixtures (COM) as a composite fuel to conserve oil resources and relieve import supply problems is being vigorously promoted by the Department of Energy via the sponsoring of various demonstration units (1). The idea of COM as a useful alternative fuel has been explored on and off for over 100 years (2). The approach must be capable of grinding, mixing, storing, and combusting COM with presumably only minor equipment changes on oil-fired boilers. DOE estimates that 56 000 m3 of oil (350 000 barrels) could be spared daily if a 50-50 COM was used to generate electricity. Of course, the ability of COM suppliers to prepare and deliver a stable suspension of COM at reasonable economic costs must be achieved if the concept is to be successful. This report reviews the various methods used to attain stable coal-oil mixtures. Various physical-chemical principles associated with each method of stabilization are also discussed.

Jan 1, 1981

By Collin L. Stewart

Published subsidence data for the western United States is limited in comparison with data for the east. This paper summarizes the results of a subsidence monitoring program above two longwall panels at the Foidel Creek Mine located in northwest Colorado. The monitoring area is characterized by overburden ranging from 1000 ft to 1100 ft in thickness. The surface slope parallels the dip of the bedding at approximately 5 deg. Average mining height is 9 ft. Smax averaged 3.4 ft. Draw angles averaged 15 deg for up-dip ribsides and 19 deg for down-dip ribsides. A site-specific profile function is developed from the data.

Jan 1, 1986

By E. h. Erwin Gaertner

Before dealing with the technical equipment of this paper a short survey of the Rhenish Brown Coal Area is given in order to illustrate the special geologic and environmental conditions in this region, which led to the development of the mining technics, used today.

Jan 1, 1975

By William Gleason

With more than 20 major mines extracting copper, gold, coal, molybdenum and lime, Arizona is recognized as one of the better mining jurisdictions, not just in the United States, but in the world. However, that is not to say the road to production is always paved with gold, or in many cases, copper. Earning the license to mine in Arizona is a complex process with years of paperwork and permitting before the first tons of ore are ever processed. Now, get the federal government involved and the process becomes even more complex, and the path to production can become even longer.

Jan 1, 2013

By S. McAlister

This paper outlines the development of the Falcon enhanced gravity separator. Design objectives included continuous operation with sharp separations, mechanical simplicity, minimization of process water demand, the ability to apply a centrifugal field up to 300G's, unit capacity in excess of 100 t/h within a footprint of 10 square meters, a capital cost below $US 4,000 per t/h capacity, and total operating costs of less than $US 0.40 per tonne. A parallel development has been inexpensive, effective, semi-continuous equipment for recovery of precious metals in the free metallic state. These objectives have been largely met. There are significant opportunities for the technology in many mineral processing applications.

Jan 1, 1998

By W. V. Liu, D. Omane, H. Yu, Y. Pourrahimian

"A large-scale wildfire had broken out at Fort McMurray in Alberta, Canada during May 2016. Many oil sands mining activities were affected due to the wildfire and the associated ash emissions. In particular, ash emission generated from the fire outbreak is a huge problem during the post-fire cleanup. These emissions pose a severe health hazard to workers, environment, and global climate. The ashes emitted into the atmosphere are caused by either human activities or climate conditions. The objective of this research is to assess the effect of three different ash dust suppressants, namely water, #1 surfactants, and #2 polymers at various volumetric concentrations on ashes samples to prevent propagation of fine solid emissions into the atmosphere. It is found that both #1 surfactants solution and #2 polymers solution are effective in retaining fugitive ash dust generated from the ashes. Volumetric concentration efficiency of 0.05% of #1 surfactant and 5% of #2 polymers in 500 ml of water have been proven to provide ash dust retention efficiency greater than 99% after the spraying of these suppressants. It is also found that both #1 surfactants solution and #2 polymers solution maintain an ash dust retention efficiency higher than that of the use of only water. This confirms the merit of using chemical dust suppressants on fugitive ash dust for a longer period, which is proven by the 72-hour data from this experiment. This study gives a general view of how effective chemical suppressants on fugitive ash emissions work. INTRODUCTION On May 1st, 2016, a large-scale wildfire gutted Fort McMurray, Alberta, Canada. Many oil sands mining activities were affected due to the wildfire and the associated ash emission. Due to the wildfire, some of the biggest oil sands companies in Fort McMurray such as Royal Dutch Shell and Suncor Energy shut down their oil production, at 255,000 and 350,000 barrels per day respectively [1]. Syncrude Canada Ltd scaled down its normal production capacity level of 350,000 barrels per day [1]. This generated an estimated loss of about 1.1 million barrels of oil production per day, constituting a 30% reduction in the Canadian daily oil production, crippling the economy [2]. This loss in production by the companies translated into 0.33 % of the Alberta GDP in 2016 constituting a loss of $985 million and 0.06 % of the entire Canadian economy [3]. In 2017, it is estimated that the rebuilding and reclamation of the affected areas in Fort McMurray will add $ 1.3 billion in GDP to Alberta’s economy [3]. A population of over 90,000 people was evacuated from the location and its surroundings for health and safety reasons [4]. The fire destroyed about 2,400 structures and over 500,000 hectares of forest vegetation in Fort McMurray, leaving an estimated 232,000 tonne of post-fire ashes [5,6]."

Jan 1, 2017

By BHAMIDIPATI S. SASTRY, Pavan Kumar Kattamuri, ADITYA PANDEY

The thermal conductivity of rock surrounding the airway is one of the most important thermal properties for estimating strata heat transfer into the mine air and for designing the air-cooling strategies. Several laboratory methods are available for the determination of thermal conductivity; however, most of them are complex and cumbersome. The present study explains the working principle of Lee’s apparatus which is relatively simple, easy to fabricate and use, and provides consistent results. In the present study, thermal conductivities of sandstone cores obtained from an Indian coal mine are determined using Lee’s apparatus. An approach is discussed for determining the temperature gradient of sandstone specimens while cooling and used for calculating thermal conductivity. The thermal conductivity of different sandstone specimens attains values between 2.37 and 2.59 W m− 1 °C−1. For different sandstone cores obtained from the field, properties including specific gravity, specific heat capacity, thermal diffusivity, and porosity, along with thermal conductivity, are determined and highlighted in this study.

Jul 20, 2021

By Shangyong Lin, Wei Sun, Weiping Liu, Muhammad Azam, Junfeng Cheng, Yujie Zhao, David Asubonteng, Michael Ngoie

Copper concentrates have wide application in global smelting operations, comprising primarily of chalcopyrite (CuFeS2) as the principal mineral, accompanied by chalcocite (Cu2S) and bornite (Cu5FeS4) as secondary copper-bearing minerals. However, these concentrates frequently harbor detrimental impurities, notably fluorine ions, which can cause various complications during the smelting process. Moreover, an elevated fluorine content in copper concentrates may entail financial penalties and sales constraints. This review conducts a comprehensive analysis of existing methods for the removal of fluorine, presenting a nuanced assessment of their merits and demerits. It also provides valuable insights into the current landscape of fluorine elimination from copper concentrates and pinpoints pivotal areas warranting future investigation. This review endeavors to serve as a pragmatic resource for researchers and industry professionals operating within this domain.

Jan 1, 2024

By Chee Theng

"What do you think are the most important topics in mineral processing today? It is a question that begs to be asked when more than 100 of some of the best and brightest in Colorado mineral processing and their invited guests are gathered in one room. They are there for the 66th Annual Colorado MPD Meeting held at The Broadmoor in Colorado Springs: three days of finely curated talks and social events where participation was strong, and information was exchanged and connections forged in a relaxed, informal atmosphere.Water, tailings and social licenseNot surprisingly, water management, with the associated issues of tailings and social license, was high on the minds of those present. The Mount Polley and Samarco tailings dam failures have had repercussions across the industry. “There are big challenges with respect to tailings, and social and environmental pressures to find better ways to treat them,” said Steve Hearn of Huntsman Corp., a view echoed by Bob Kilborn of Kilborn Group LLC. Metso Minerals director Keith Butler said, “Water conservation is a key issue today. Many mining activities are now located in remote areas, so it has social and economic impacts on mining operations.” For Brian Olson of Samuel Engineering, wastewater and reclaimed-water treatment is interesting.Fittingly, the first talk of the meeting was on dry stack tailings by Michael Blois of Takraf USA, who went over both the advantages and disadvantages. “The average now is over one tailings dam failure a year,” Blois said, “and that is one too many.” But the technology may not be the right fit for all projects. In his talk on the KSM project, Jay Layman, president and COO of Seabridge Gold, showed how it isn’t practical for KSM and how Seabridge reached the decision on a cyclone sand tailings managementfacility as the preferred management strategy.The luncheon keynote also dealt with a tailings pond spill, but of a different kind. Bob Schafer, chief executive of Eagle Mines Management, spoke on the federal missteps that led to the spill into the Animas River from the Gold King Mine, a mine that had been a dry mine throughout its life and up to the 1990s."

Jun 1, 2016

By George D. Haley

This report will be given in two sections. The first sec¬tion outlines techniques and equipment to form almond shaped fluorspar briquettes by means of briquet presses, and the second section outlines techniques of the balling disc. PART I - BRIQUET PRESSES Fluorspar has been briquetted for a number of years and the so called "peach pit" briquet is known to many steelmen. Present production is estimated at over 100,000 tons annually. Slide 1 shows an assortment of various sizes and shapes of briquettes. It is possible to form fluorspar into almost any configuration of briquet. For safety on the melting floor, pillow type briquets are preferred. Ease of mechanical handling and durability of the product are facil¬itated by an almond shape. The dimensions of the almond can vary from 1-in. to 1-1/2-in. in length, from 13/16-in. to 1-in. in width and from 1/2-in. to 1-in. in thickness. The type of equipment to pro¬duce almond shaped fluorspar briquettes is shown in Slide 2. Here we have a Komarek-Greaves and Company 300 ton briquettor equipped with almond rolls. This machine is capable of producing fluorspar briquettes at a rats of 30 tons per hour with power consumption of 35 hp per ton par hour.

Jan 1, 1969

By Thomas B. Dellinger

Since 1950, rotary-drilled, large-diameter holes, "big holes", with depths to over 300 feet and diameters of over 30 inches have become numerous and widespread. Fifty such holes have been drilled for access shafts to LPG mined caverns, Over 70 holes have been drilled for various other commercial activities. Over 150 holes have been drilled by the AEC for atomic testing purposes. These holes have ranged up to 300-inch diameters with 1600-foot depths, 120-inch diameters with 570-foot depths, and 72-inch diameters with 4800-foot depths. Equipment is now available to drill a wide range of ?big holes? for varied requirements. At least a dozen drilling contractors are participating or have participated in the drilling of "big holes". The accompanying tables show pertinent historical, technical and economic data on over 250 holes. The illustrations to be presented concurrently with this paper show the various equipment and accessories now in use. (See Appendix I for captions of illustrations.)

Jan 1, 1966

By J. Herbst, J. Groppo, A. Noble, R. Q. Honaker

"Coal and coal byproducts produced annually contain enough rare earth elements (REEs) to meet current U.S. demand. The REEs exist in the form of minerals, ion-exchanged elements associated with clays and chemically bonded elements within the organic coal matrix. Researchers at three universities have collaborated to evaluate the effectiveness of existing physical and chemical concentration processes for the recovery of the REEs. The efforts have found that physical separation processes can increase the total REE content in the thickener underflow material collected from a Central Appalachian coal cleaning facility from around 300 ppm to values greater than 17,500 ppm on an ash basis. On the other hand, leaching was effective in recovering REEs from coarse middlings materials collected from multiple coal basins as indicated by recovery values exceeding 80%. Based on material characterization data and process evaluations conducted for several potential feed coal sources, economic recovery of the REEs will require byproduct production of both clean coal and REE concentrate using a process flowsheet that is unique for each source. INTRODUCTION Recent studies initiated by NETL showed that U.S. coals contain significant amounts of rare earth elements (REEs), suggesting that rare earth minerals (REMs) and/or REEs can be produced as byproducts [1]. According to the report, the richest source of REEs is the Central Appalachian coal. At present, there are 208 coal preparation plants located in the region (WV, KY, PA, VA, AL, TN) with a capacity of 166,495 tons/hr or more than 1 billion tons annually [2]. If only a portion of these plants are retrofitted with advanced separation processes, the U.S. coal industry can become a significant producer of RE minerals as byproducts. An inherent advantage of becoming a byproduct producer of REEs is that no mining cost needs to be part of the product cost. Other researchers have also shown that coal can be a significant source of REEs. The average sum of the rare earth plus yttrium (REY) concentration of the world coal is approximately 68.5 ppm, which is lower than the corresponding upper crustal concentration (UCC) (168.4 ppm). However, the average REY content of the mineral matter in the world (404 ppm) and U.S. coals (517 ppm) are 3 times higher than the average UCC. Some of the mineral matter in Russian and Chinese coals have REY concentrations in the range of 0.68 to 2.03% and contain a better source of higher value REYs than many primary rare earth deposits [3]."

Jan 1, 2017

By P. D. Roa, O. Noirot, H. Owens, D. E. Walsh, J. R. Mokka

Over a period of eight years (1989 through 1997) the Mineral Industry Research Laboratory (MIRL) at the University of Alaska, Fairbanks, AK, has investigated the effects of temperature, residence time and particle size on the degree of low-rank coal (LRC) upgrading for a nonevaporative, hydrothermal drying process, also known as hot water drying (HWD). The following three Alaskan LRCs were used in this study: Usibelli coal (Seam No. 4) from the Nenana Coal Field, Little Tonzona coal from near McGrath, and Beluga coal from the Beluga-Yentna field on the west side of Cook Inlet. Replicated factorial tests were conducted. Experimental results indicate that most of the low-rank coal upgrading via HWD occurs rapidly within the first 10 to 20 min of residence time. Thereafter, the upgrading process slows down, and more than 100 min of additional residence time is required to produce percentage increases equivalent to what was achieved in the first 10 to 20 min. The properties of the hot water dried products were very sensitive to process temperature. Calorific value, carbon and oxygen contents, equilibrium moisture levels and Hardgrove gindabilities all appear to change linearly with temperature within the 275°C to 325°C (525°F to 61 5 OF) range.

Jan 1, 2000