Search Documents

By R. K. Sinha, B. S. Choudhary, Desh Deepak, A. K. Mishra, Hemant Agrawal, Shankar Kumar

There are several methods (empirical, statistical, and machine learning tools) to calculate blast-induced ground vibration. Still, due to complications in the blasting procedure, under varying blasting loads and strata conditions, it is not easy to predict and simulate blast vibration precisely. Therefore, a study was conducted to simulate the field blast data in Ansys software using explicit dynamics. For this study, monitoring of ground vibration for 20 single hole blasts was carried out. The density of emulsion explosives was in the range of 0.9 to 1.15 g/cc. In the laboratory, rock properties were determined from the rock sample collected from the mine site before blasting. The in-hole velocity of detonation (VoD) and the density of the emulsion explosive were also determined. These parameters were used for numerical analysis to know the ground vibrations at specified points. The results of ground vibration predicted by the model are validated using field data.

By E. K. Albert

In 1977, Congress enacted Title IV of the Surface Mining Control and Reclamation Act (SMCRA), providing for an "abandoned ml.ne reclamation fund". This fund, taken from a fee collected from operating coal mines, provides capital for the reclamation process. However, given the number and extent of abandoned mine sites in some states, the question of project selection is important. This paper describes a project in progress to create a Management Information System application for project ranking under multiple objectives. The benefit of this project for the need of new environmental control technologies will be discussed.

Jan 1, 1990

By Ewald H. Kurt

The story of America's progressing standard of living is the story of machines. The automobile, the airplane and the telephone for example have made our transportation and communication systems what they are today. Even they depend in turn on another machine -- the rock drill. By making it possible to economically mine and quarry minerals in large quantities, this versatile machine supports virtually every American industry relying on the earth for its buried raw materials. And, like all machines, the rock drill's mechanical evolution was stimulated by production demands placed upon it. All percussion drills are mechanized versions of the original drilling unit -- man, Figure - illustrates a double jack team at work before the turn of the century. The man with the sledge hammer is the impact device while the man sitting is the rotation mechanism and feed motor. The first drifter drills (Figure 2) performed the same function but with increased mechanical efficiency. A piston controlled by a valve produced impact. A built-in ratcheting mechanism provided rotation and a hand-cranked screw provided feed thrust. As the industrial revolution proceeded into the twentieth century, the demand for raw materials stimulated refinements of all recovery machinery, including rock drills. As drills became heavier and more powerful, a mounting (or carrier) had to be provided to move the drill from hole to hole. This resulted in the development of the wagon drill (Figure 3). Propelled by muscle power, the wagon drill was for years the standard tool of the surface drilling industry (Figure 4). As drills penetrated faster and as labor increased in cost, the time consumed in nondrilling peripheral operations had to be

Jan 1, 1977

By Lawson. Heather

"The purpose of this study is to explore how the geochemical and petrographic components of coal may impact its physical properties, as well as how these components correlate with a history of reportable dynamic failure in coal mines. Dynamic failure events, also termed bumps, bounces, or bursts, are the explosive failures of rock in a mining environment. These events occur suddenly and often with no warning, resulting in worker injury up to and including fatality in greater than 60% of MSHA reportable cases. A database of variables was compiled using publicly available datasets, which included compositional geographic, strength, and Hardgrove Grindability Index (HGI) data (ACARP, 1998). Results indicate that bumping coals are less mature, lower in carbon, higher in oxygen, softer, and less well cleated than coals that do not bump. High liptinite content was found to correlate with higher average UCS values. However, no clear, direct correlation between UCS and dynamic failure status was observed. The findings of this study establish that differences exist between coals that have experienced reportable dynamic failure accidents versus those that have not. These differences are inherent to the coal itself, independent of mining-induced risk factors. Results further illuminate how compositional attributes of coal influence physical properties and begin to clarify potential links between geochemistry and dynamic failure status. Only through the better understanding of risk can more effective mitigating strategies be enacted.INTRODUCTIONDynamic failure events, also termed bumps, bounces, or bursts, are the sudden failures of rock in a mining or quarrying environment. Failure occurs when the rock’s critical bearing capacity has been exceeded and the rock fails energetically through the outward expulsion of rubblized material (Peng, 2008). These events occur suddenly and often with no warning, resulting in worker injury up to and including fatality in greater than 60% of reported cases through the Mine Safety and Health Administration (MSHA). Much research has been devoted to the prevention of these events. The effects of overburden depth and stiffness, mine design, mining practices, and in situ stresses are well documented (Agapito and Goodrich, 2000; Brauner, 1994; Campoli and Kertis, 1987; Holland and Thomas, 1954; Iannacchione and Zelanko, 1995; Lawson et al., 2016b; Mark, 2016; Newman, 2002; Peng, 2008; Whyatt, 2008). Despite these significant advancements in coal mine ground control, however, events continue to occur. Proactive risk mitigation remains an important research area. This is particularly true in underground coal settings, where the rockmass is layered, lithologically diverse, and does not exhibit consistent material properties across deposits.Many conditions have been associated with the occurrence of dynamic failure phenomena, including:"

Jan 1, 2019

By Jingzhi Liu, Xueping Hu, Huai Wang, Simin Yang, Baoqiang Yu, Deguang Zhan

In this study, response surface methodology (RSM) and Box-Behnken design to improve copper extraction from refractory copper oxide ore were investigated. Based on single factor tests, quadratic polynomial equation to describe the relationship between influencing factors (particle size, leaching temperature, sulfuric acid concentration, leaching time) and copper leaching rate could be obtained by RSM. The optimum parameters determined by the model are as follows: particle size 64.60% − 74 μm, leaching temperature 74.15 °C, sulfuric acid concentration 0.49 mol/L, and leaching time 140.85 min. Under these conditions, experimental copper leaching rate of 85.12% could be achieved, which was very close to the predicted maximum value (85.34%) by the model, indicating the quadratic polynomial model was accurate and reliable. Copper leaching rate increased approximately by five percentage points comparing to the result of single factor tests. This study indicates that response surface methodology is an effective method to optimize experiment conditions and achieve an ideal experiment result.

Aug 17, 2022

By D. J. MacKinnon

Smooth, compact, dendrite-free, 24-h zinc deposits have been electrowon from zinc chloride electrolyte using a diaphragm cell. The cell consisted of sealed anode compartment con- taining DSA anodes which were separated from an open cathode compartment by Dynel cloth membranes. Fresh electrolyte was fed to the cathode compartment where zinc deposition onto an aluminum cathode was aided by air-sparging. The catholyte passed through the diaphragm into the anode compartment from which chlorine gas and spent anolyte were withdram.

Jan 1, 1980

By Rebecca Boakye, Zohreh Kazemi Motlagh, Virginia T. McLemore

The most significant uranium (U) deposits in New Mexico are sandstone-hosted deposits in the Morrison Formation (Westwater Canyon Member), where >169,500 short tons of U3O8 were produced from 1950 to 2002. In addition, >9076 pounds of vanadium (V, a critical mineral) and some molybdenum (Mo) were produced from these deposits. These and other U deposits (limestone-hosted, U-veins) in New Mexico also contain critical minerals. Critical minerals are mineral resources that are essential to our economy and whose supply may be disrupted; many critical minerals are 100% imported into the U.S. Some sandstonehosted, limestone-hosted, and U-vein deposits are elevated in heavy rare earth elements. One sandstone-hosted sample contained 0.3 ppm Re (critical mineral), 659 ppm Se and 408 ppm Mo. The arsenide five-element vein deposits in the Black Hawk district are mineralogically and texturally complex, low- to moderate-temperature, hydrothermal, structurally-controlled, Ag-Co-Ni-Bi-As bearing carbonate vein systems with local minor elements. Mineralized samples from Black Hawk contain up to 9970 ppm Ag, 8540 ppm As, 5690 ppm Co, 72,400 ppm Ni, 57 ppm Bi, 165 ppm Sb, and 32,600 ppm U.

Feb 22, 2026

By Jenny Alsén, Hans Hogard

"Construction of large facilities underground in urban areas has many advantages. In order to show the advantages, a case study of the Norsborg metro depot in Stockholm Sweden has been made. The Norsborg metro depot will be the largest and most modern underground metro depot in northern Europe. The depot has been built in hard rock in an urban area with small impact on the environment and local residents. The paper describes how it is possible to build underground facilities in a cost efficient way and take care of the challenges regarding working environment that comes with locating a permanent working place underground. INTRODUCTION The Stockholm area is one of the five fastest growing regions in Europe and home to more than a fifth of Sweden's population on just two percent of Sweden's surface. The population is growing rapidly, with about 35,000 people per year and is expected to reach 2.6 million in 2030. In order to meet the development and enable continued growth, housing projects and expansion of infrastructure need to keep the same pace; this is an easy conclusion to make but much more difficult to realize in practice. The main challenge is to accomplish development in a sustainable and efficient manner, minimizing the use of resources and land. By constructing facilities underground more urban space will be made available for development and/or for greening of city centers. Considering sustainability factors such as land value in decision making for placing of structures or facilities, underground locations could become a first choice alternative. During 2015 and 2016, several major underground infrastructure projects in the city of Stockholm will start, including a 14 km sewage tunnel and an 18 km by-pass highway tunnel. Furthermore the Stockholm metro system is currently undergoing the largest expansion since the 1970’s, a 19 kilometers extension of the metro system including new trains and new stations is planned. During 2013 - 2015 Skanska Sweden took part in the construction of a new metro depot placed underground in the southern part of Stockholm; the Norsborg metro depot. This is a top modern urban underground facility that in 2017 will serve as depot for 17 new metro trains. The project was selected for “Outstanding Project of The Year” at the ITA Tunneling Awards 2015."

Jan 1, 2016

By J. Pancher

"Stainless steel castings are used in abundance in the mineral processing industry. In rotary kiln-based processes, these castings are typically exposed to high loads, corrosive elements, mechanical abrasion and cyclical temperature exposure. In the processing of iron ore pellets, it is typical to use a traveling grate preheater or a straight grate furnace to heat the pellets. Both machines have a conveyor that is mainly comprised of high temperature stainless steel castings. It is these castings which are the focus of this study. The expected life of these castings can be quite short, their cost quite high and the effort to replace them very labor intensive. The goal of this study was to gain a better understanding of the failure modes of these castings. With that basic understanding, modifications to the alloy content could be made to achieve a new operational paradigm. That paradigm could be a cheaper casting, a longer lasting casting or a casting tailored to special operating conditions (for example, highly corrosive gases or sudden temperature shocks). Over the past 4 years, Metso Minerals has sought to achieve a better understanding of the failure modes through modeling, laboratory testing and sampling of used castings from various end-users. In addition, we have tested new alloys in a laboratory setting and also in the field to see how they would perform compared to the existing ""standard casting"". Our testing has revealed interesting data concerning the impact toughness, sigma phase content and formation, chloride attack and other performance attributes of various grades of stainless steel when exposed to cyclical temperatures. Interesting results were also obtained concerning the addition of rare earth elements (Niobium, Boron, etc), nitrogen and manganese to a typical ASTM A297 grade of stainless steel. To date, a few hundred test castings have been installed in iron ore pellet plants worldwide. Many of these test castings have already experienced a year or more of operation with good results.INTRODUCTION Cast stainless steels (ASTM A297 and similar) are a main constituent used in the construction of iron ore pelletizing equipment. A typical straight grate pelletizing machine would contain upwards of 160,000lbs of ASTM A297 Grade HH castings. With a typical casting lasting only two to four years, and a casting costing around $35USD, it is easy to see that the castings are a main contributor to the overall cost of producing the pellets. Grade HH and HI (see chemical composition listed below) became the “go to” materials in the 1960’s and very few changes have been made to this day (the exception being plants that switched to flux pellet production in the 1980’s)."

Jan 1, 2015

By Hemant Agrawal, Arvind Kumar Mishra

Rock breakage using blasting is one of the important operations of the mining industry. The delay timing decides the initiation sequence of holes in the blasts and is a crucial factor to improve the overall blast performance. Blast-induced ground vibration is an undesired yet unavoidable outcome of blasting. Peak particle velocity (PPV) is commonly used to measure the magnitude of blast-induced ground vibration. Channelization and better utilization of explosive energy delay are provided between blast holes using initiating systems. The use of different initiation systems even on the same site results in a very significant difference in the values of PPV generated. Due to scattered delay timings of pyrotechnic detonators, the scaled distance predictor equations obtained become unreliable. The error/scatter in delay timing leads to overlapping of holes and hence increases in maximum charge per delay. In this paper, an analytical approach has been discussed to measure the overlapping of holes during blasting with initiation systems having inherent cap scatter. The analytical approach will be calculating the probable overlapping of holes due to scatter in delay timing and will help blasting engineers to understand the variation in maximum charge per delay due to pyrotechnic based initiating systems. In this study, a total number of 102 blasts were conducted using different initiation systems at two different opencast coal mine and 221 corresponding blast vibrations events were recorded.

Nov 10, 2020

By Renee Royer, Allan Punkkinen

As mines progress to ever increasing depth, new challenges are encountered with serious concerns for rock excavations in highly stressed conditions. New procedures have been undertaken or are under way to remove workers from the workface, mitigating risk and exposure to hazardous conditions. Rockbolting crews are at particular risk as they are the first line of defense in the installation of the ground support systems. One such initiative for removal of workers from danger has been with remote bolting. Equipment manufacturers have had the ability to remotely inject resin pneumatically into boreholes for several years, but it has not been recognized as a very effective method due to a variety of complications. This makes the installation of dynamic support system components such as the D-Bolt® increasingly difficult. More recently, hollow-core bolts have become popular providing far more effective installation when installed with pumpable, two component urea-silicate injection resins. Normet has developed high energy dissipation self-drilling dynamic bolts (SDDB®) to meet these challenges. Following several inquiries as to the effectiveness of pumpable resins for use with dynamic support components, Normet Canada performed comprehensive testing of the bolt and resin system at CanmetMINING in Ottawa to dispel or substantiate any preconceived beliefs. Several dynamic and static tests in direct and indirect loading were carried out. Results include tests in shear and early strength UCS of the resin to measure the performance of the SDDB compared with the established D Bolt as an effective dynamic ground support component. Underground field observations, installation methodology and in-situ testing are investigated.

Apr 26, 2022

By K. Kovári, G. Anagnostou

Slurry and EPB-shield tunnelling have been successfully applied worldwide in recent years. Under extremely unfavourable geological conditions, however, face instabilities may occur. The present paper aims at a better understanding of the mechanics of face failure. For the case of slurry shield, attention will be paid to the time-dependent effects associated with the infiltration of slurry into the ground ahead of the face. Related topics, such as the stand-up time and the effect of the excavation advance rate, will be discussed. In the case of an EPB-shield, a distinction will be drawn between fluid-pressure and effective pressure in the chamber. The effective pressure can be visualized as a “grain to grain” contact pressure between the muck and the ground at the face. The water pressure in the chamber reduces the hydraulic head gradient in the ground and, consequently, the seepage forces acting in front of the face. The face is thus stabilized both by the direct support of the pressurized muck and by the reduction of the seepage forces in the ground. The paper includes normalized diagrams which allow the assessment of tunnel face stability.

Jan 1, 1997

By D. A. Shock

Utilizing the technology developed for oil well stimulation by hydrofracing, a disposal system which permanently fixes the waste has been proven. Large quantities of radioactive waste can be processed by a single well system making this method an attractive method for permanent radioactive waste disposal. The system depends on locating a relatively thick formation of impermeable, but easily fracturable rock such as a shale, creating a horizontal fracture, pumping the waste into the fracture in a form which will subsequently solidify and seal the fracture from the well system. The paper presents the theoretical considerations from creating and extending horizontal fractures and how these considerations were used in designing a waste disposal system which is now operating.

Jan 1, 1964

By S. G. Malghan

W.H. Moyer In reference to the section “Excess pyrite, ” the author discusses difficulties in separating chalcopyrite from pyrite. A technique does exist, and has been used commercially, for the flotation, separation, and recovery, if desired, of both chalcopyrite and pyrite. The method was described in Mining Engineering, March 1966, “An Improved Flotation Method for Cornwall Sulfides. ” While it was not used on a porphyry copper ore, it was used on a chalcopyrite - pyrite-containing ore and might well have application. Both sulfides, chalcopyrite and pyrite, were floated simultaneously using xanthate as a collector and MIBC frother to produce a cleaned sulfide product. This concentrate was then thickened and conditioned at high solids with aeration and lime to a pH above 12.0 for a period of 1.5 to 2 hr. A supplemental suppressant, such as cyanide, could be used if necessary to sharpen the subsequent separation; however, it was not required at Cornwall. The conditioned sulfides were floated with two stages of cleaning to produce a highgrade chalcopyrite froth product and a pyrite sink product barren in copper. The separation at Cornwall gave a 28.6q. Cu grade chalcopyrite product and a pyrite analyzing 0.0670 Cu. A desliming step on the raw ore initially used at Cornwall for a period of time was later discontinued. Advantages to be found in using a strong sulfide collector, such as a xanthate, is the rapid flotation it induces and, generally, an ability to float at a coarser grind. A following regrind circuit could be used to give maximum liberation and produce a clean sulfide concentration. The “differential” separation is concerned primarily with grade and with assuring a barren pyrite for maximum recovery.

Jan 11, 1986

Placing a detonating explosive inside a volume of rock is an efficient method of rock fragmentation. The explosion generates internal tensile stresses in the rock, and because rock is a brittle material, this brings about crack propagation and fragmentation far more efficiently than does application of explosive on the surface. To get the explosive inside, we drill a pattern of boreholes and charge the explosive into the holes. This is really the one and only purpose of making blastholes in mining: to give access for the explosive to the interior of the rock. No matter how big and expensive a drilling jumbo we stand up in front of a rock face, and no matter how many boreholes we let it drill, the rock does not fall apart by itself without blasting. It is the action of the explosive in the boreholes that does it. When we consider that we need a pound or two of explosive for every cubic yard of rock to be fragmented, and a pint of borehole volume for each pound of explosive, we see that the process of blasthole charging is an important element in the whole process of rock blasting.

Jan 1, 1975

By Peter Werner

Technological advances in mine equipment and milling processes have enabled mining companies to exploit ever lower grades of ore. The result has been larger disturbances, greater volumes of waste, a complex web of infrastructure, and an overall trend toward mega projects that can extend over several square kilometers. This explosive growth in a mining operation’s disturbance footprint provokes an obvious question: What is it going to cost to reclaim all of this? At face value, this can be an enormous financial liability for a company, but since the timing of reclamation may be years in the future for many operations, these costs can be heavily discounted, thereby limiting the burden on the corporate balance sheet. Nonetheless, mining companies are eager to remove these liabilities as quickly as possible; conversely, regulators want assurance reclamation will, in fact, occur. How might one bridge these competing interests? Navigating the practical and financial requirements of a post-closure landscape requires foresight, judgement and assumptions; however, companies that do not adequately plan for these future expenditures when there is no offsetting income stream will likely face some difficult decisions. Simple risk analysis tools and utilizing the time value of money can help bring some clarity to this end-of-mine life phase.

Dec 1, 2025

By George H. K. Schenck

The North American-based mining engineer needs to understand the differences that exist between mechanical mining or boring machines built on this continent and those built in Europe. The differences Ere most clearly seen when machines for large-sized openings--about 15 feet high-are considered. This report will focus on the innovations of European origin. The rock-breaking tool, drag bit, or roller cone that is efficient for a particular project is related directly to the strength of the rock involved. This strength is generally stated in reference to the rock's unconfined compressivee strength in pounds per square inch (psi) although it is well recognized that a rock's shear strength is also important. Compressive strength has been adopted because it is simple to test for and provides a convenient comparison. Table 1 relates cutter type to compressive strength and indicates the general nature of the machine innovation devel¬oped in Europe.

Jan 1, 1970

By E. F. Schnitzer

During 1996 and 1997, Oregon experienced flooding on a scale not seen in many years. Some gravel pits located near rivers experienced erosion and, in several cases, breaches between the gravel pit and the river. Initial evaluation of several sites that experienced breaches indicates that impacts to the river system are complex and vary significantly from site to site. The impacts to the adjacent river system may be viewed as both positive and negative. Several floodplain-mining sites in Oregon located in areas of historic river flow have reverted to active riverbed. In many cases, state and federal fisheries biologists and university researchers see the resulting increase in channel complexity and habitat as favorable. The Oregon Department of Geology and Mineral Industries -Mined Land Reclamation Program (DOGAMI-MLR) is performing additional studies of the impacts to the off-channel areas that resulted from the 1996 floods. More data is needed to make sound floodplain decisions regarding mining.

Jan 1, 1999

By J. Paraszczak

Underground metal mining involves many challenges. Economic slowdown, tough international competition and sometimes volatile metal prices put constant pressure on mine operators to increase productivity and to reduce production cost. At the same time, countries such as Canada, the United States and Australia are experiencing skilled labor shortages that might even stall development of certain mine projects. Furthermore, some stages of underground production take place in particularly hazardous environments where the safety and health of miners is at risk. Automation of some processes in underground mining is one of the promising avenues to alleviate some of these problems. Loading and haulage are among the most critical operations and areas where implementation of autonomous vehicles has been targeted. However, although health and safety issues are a primary driver to opt for automation, the latter should ensure an acceptable level of productivity and pro?tability. With this in mind, this article focuses on the factors affecting operational effectiveness of autonomous underground loading and haulage equipment and the means to maximize it.

By S. A. Diatchkov

There is a misconception that mineral-project economic evaluations in the former Soviet Union are either nonexistent or very limited. This is not the case. In fact, there are at least two basic methods that can be utilized to evaluate the vast mineral resources of the Commonwealth of Independent States (CIS). Evaluation procedures are based either on a comparison to known projects, which may rely on limited available data, or on potential-profit calculations, which generally uses more extensive databases. Significant philosophical differences between these systems and those utilized in the Western world include the following: •Under the centralized-government system, the economic evaluation of a mineral project was based on artificially determined mineral prices and costs. Every ten to 12 years, prices for concentrates and metals were established by the Council of Ministers and remained unchanged until the next reconsideration of prices .

Jan 1, 1995