Search Documents

By J. F. T. Agapito

Stability in Exxon's Colony Pilot Mine in the Piceance Creek Basin, Colorado has been monitored by periodic pillar stress-determinations End roof-to-floor convergence measurements since 1971. Pillar failure has caused marginal stability in some areas of the mine. Measurements taken during the process of failure provided valuable information on the in-situ pillar strength and long-term behavior of the mine structure. Four pillars were reinforced by 32 mm (1-1/4 in) diameter tensioned grouted bolts to increase long-term stability in the northern area of the mine. Stability of this area is necessary because future plans envision its use as an exit/access and ventilation exhaust. Computer analyses were performed to help evaluate the effect of pillar reinforcement on long-term stability. Results indicate that bolting is particularly useful in stabilizing failed pillars, but its effects are significant only in the immediate area of the pillar. The projected significant decrease in deformation of two extensively failed pillars near a main entry indicates that bolting reinforcement will assist the long-term stability of the opening.

Jan 1, 1985

By Yuting Xue, Alper Kirmaci, Taghi Sherizadeh, Khaled Mohamed

Resin-grouted bolts serve as a crucial means of stabilizing yielded coal ribs in underground coal mines. A comprehensive investigation into their efficacy was undertaken by a collaborative effort between the National Institute for Occupational Safety and Health (NIOSH) and Missouri University of Science and Technology (MST). This study involved pull-out tests in multiple locations, including six coal mines and the NIOSH research mine. A total of seventy-three (73) tests were conducted, of wide range of anchorage lengths, ranging from a short encapsulation length of 0.305 m to a fully grouted encapsulation length of 1.524 m. The test findings indicate that when short encapsulation bolts are installed at high rotation speeds, their anchorage capacity is significantly reduced, leading to failure at the bolt-grout interface. Conversely, when these bolts are installed at lower rotation speeds, they exhibit greater capacity, with failure occurring at a higher anchorage load equivalent to the yield load of steel rebar. No matter what the rotational speeds were used during bolt installation in this study, the fully grouted bolts consistently experienced failure at the ultimate load of the steel rebar. Most of the tests carried out on partially grouted bolts with anchorage lengths of 0.610 - 0.914 m have shown behavior patterns like the fully grouted bolts, although exhibiting reduced stiffness. The outcomes of this research offer a profound insight into the ways in which resin-grouted bolts enhance the stability of coal mine ribs.

Feb 1, 2024

By Richard DePew, Robert J. Auber

The Westerly Storage Tunnel is a 25-foot diameter segmentally lined storage tunnel that is a major component of the Northeast Ohio Regional Sewer District's Project Clean Lake that is designed to capture 39 million gallons of untreated CSO overflows from entering Lake Erie. During the final stages of the project completion, a large-scale rock fallout incident occurred during the final lining installation operations at the down-stream end of the tunnel that extended beyond the designed primary support system. This paper outlines the level of coordination and collaboration between the Owner, Designer and Contractor to remediate the situation safely, quickly and effectively.

Jun 23, 2024

By Gary J. Fletcher

Mining and processing activities which are proposed on private land, state leases, or unpatented mining claims are governed by numerous local, state, and federal laws which identify the procedures and conditions which must be met before resources can be developed. The respective government agencies responsible for the administration and enforcement of these laws have promulgated supporting regulations and guidelines, and have implemented certain permit and approval processes to ensure compliance. Each exploration project has a unique environ- mental setting and location which further dictates the types of air, water, hazardous waste, and wildlife laws and regulations which must be complied with before development commences. The environmental planning process should be the first step in the evaluation of existing company properties and the potential acquisition of other mineral properties. However. many company don't consider the environmental requirements for a project until the decision is made to develop the property for mining and processing. If a mining company wants to expedite the environmental planning process, it must first develop an in-house process for evaluating the project and determining the environmental approval procedures in the state where the project is located. The first stage of environmental planning involves general information which can set the overall company philosophy for development of projects.

Jan 1, 1987

By Cherie H. Tilley

The possibility of drilling oil wells from underground locations is not a new concept. It bas not been cost effective for the oil industry in the past and therefore disregarded. Today's state of the art in tunneling and shaft sinking greatly improves the potential for this type of oil field development scheme. This report presents a plan for providing a aeries of drilling bases and the design of the drilling location. The design minimizes the amount of excavation needed to develop the oil field and maximizes the use of rapid excavation techniques.

Jan 1, 1983

By Tassos Grammatikopoulos, Mike Johnson, Niels Verbaan

Seabed polymetallic nodules, which contain significant quantities of metals key to electrification such as nickel (Ni), cobalt (Co), copper (Cu) and manganese (Mn) can be processed using several different metallurgical processing options, including direct smelting and subsequent hydrometallurgical refining of the copper/nickel matte; ammoniacal leaching (gas reduction or Cuprion); and acid leaching (often reductive). Many of these approaches suffer from reduced cobalt extraction, difficult physical performance, or overall circuit complexity in general, leading to increased risk to the overall project. SGS has considered the pressure acid leaching of nodules for further investigation, as publicly shared data on this processing route stem from the 1970s and 1980s, and are not always easily accessible. This article details the series of tests conducted and provides updated results obtained — high Ni/Co/Cu recovery with limited manganese/iron (Mn/Fe) — as well as comments on the potential treatment options on the product solution and residue.

Sep 1, 2025

By John W. Barnes

In seeking cost reductions, control methods are a fertile field because they significantly affect labor and other costs. While process control in uranium mills is excellent by the evidence of high recovery, the costs seem high to those familiar with extractive operations for other metals. To some extent this high cost is inevitable, because of exacting quality control-, the technically complicated recovery processes; poor control over grade and nature of mill feed- special problems arising out of the radioactive property of the material. Practices used in uranium mills and the limitations indicated for instrumentation and automation are discussed. It is concluded that any large investment in automatic controls should be preceded by a careful study of their reliability and maintainability, and an estimate of the net income after taxes smaller plants my find it more profitable, or at least less risky, to concentrate their efforts on the possible reduction of some control problems and to development of a stable force of skilled employees. The observed experience does not inspire optimism that ore-dressing plants can be extensively automated although certain unit operations offer a challenge for improvements in instrumentation and machine design.

Jan 1, 1960

By M. J. Gula, S. S. Xue, E. P. Horwitz

A study has been conducted to remove iron from sulfate solutions using Eichrom's Dipexo® extractant, P,P'-di(2ethylhexyl) methanediphosponic acid (H2DEH[MDP]). It is found that this extractant can effectively and selectively extract ferric ion from highly acidic solutions. Ninety-nine percent of the iron was extracted from a simulated feed solution in a single stage. The separation factor, Fe/Zn, was 106. Over 90% of the iron in a loaded organic can be recovered in an aqueous solution by reductive stripping. This paper presents the experimental results. A new process for iron removal using Dipex extractant is described and discussed.

Jan 1, 1999

By M. Frenzel, D. Ebert, K. Bachmann, A. D. Renno, R. Möckel, J. Gutzmer, J. Krause

With the increasing demand for metalliferous and mineral raw materials and the consequent depletion of the global natural resource base, the possible utilization of secondary raw material sources is receiving more and more attention. In the present study, we present results from a detailed vanadium deportment study of three basic oxygen furnace slag (BOS) samples known to containing elevated bulk concentrations of vanadium. Complementary analytical methods that were used to quantify the abundance and composition of V-containing phases include SEM-based automated mineralogy, X-ray fluorescence analysis, and X-ray powder diffraction as well as electron probe microanalysis. The vanadium deportment was quantified using Monte-Carlo simulations of the data obtained from automated mineralogy and electron microprobe analysis. The total V concentrations identified by XRF are between 1.7 and 2.2 wt.% V. The most important hosts of vanadium are larnite-, brownmillerite- and portlandite-solid solutions. In two samples Ca carbonates also significantly contribute to the V deportment, while wuestite, lime, and native iron do not contribute significantly to the vanadium deportment. A thorough consistency check identifies considerable uncertainties in the density of the V-bearing phases as the most likely reason to explain remaining discrepancies between measured and calculated V values.

Oct 14, 2023

By Verya Nasri, Agustin Rey

Once completed, the Montreal Réseau Express Métropolitain (REM) will be the fourth largest automated transportation system in the world. The REM represents construction costs of approximately 7.0 billion Canadian dollars. The project consists of 67 km of twin tracks over four branches connected to downtown Montreal. The project includes 26 stations with 3 underground stations in downtown Montreal. One of the underground stations was built using the NATM method with thin permanent shotcrete initial and final liners separated by a sprayed on waterproofing membrane. The 2 other underground stations were built with the cut and cover approach including one using permanent secant pile wall with permanent walers and struts as the support of excavation and the final perimeter wall of the station. The project also includes the rehabilitation and enlargement of the Mont Royal Tunnel. This 100-year-old double track tunnel is about 5 km long. The REM also consists of 3.6 km new TBM tunnel connecting downtown to the Montreal International Airport through saturated soft ground and karstic rock. By the time of RETC, the construction of REM underground structures will be completed. This paper presents the design and construction aspects of the underground structures of this mega project.

Jun 13, 2023

By J. Kulas, J. Weaver, K. Hagley

An assessment of potential groundwater movement beneath the tailing impoundment at the Red Dog Mine was performed, and has indicated a unique aquifer situation within sub-permafrost groundwater at the site. The aquifer was shown to be isolated from both vertical recharge and a real discharge, and is characterized as a virtually no-flow system. The permafrost resulted in a deep aquifer with high tidal efficiency, meaning that variable surface loads are easily transmitted to the fluid. The tidal efficiency has been characterized through analysis of water level fluctuations that respond to earth tides, barometric pressure loads, and loading from the pond.

Jan 1, 2002

The management of risks associated with slope instability is an essential process in the safe and economic operation of open cut mines. The ?slope stability radar? (SSR) has been developed to better manage those risks. The SSR remotely scans rock slopes to continuously measure any surface movement and can be used to detect and alert users of wall movements with sub-millimeter precision. The high level of movement precision and broad area coverage of the rock face can allow for a better understanding of the geomechanics of slope deformation, including magnitude of potential failures and additional warning time of impending instability. Additionally, radar waves adequately penetrate through rain, dust and smoke to give reliable measurements, 24 hours a day. SSR systems have been deployed in many metalliferous and coal mines throughout the world. Over 80 systems are currently being used with current operations in 17 countries. Greater than 200 rock slope collapses and waste dump failures (from several to millions of tones) have been monitored, with ?warning? precursor movements recorded by the SSR. This technology enables a radical change in the management of risks in open cut mining. This paper will present recent case studies of the SSR operation in coal and metalliferous mines. Slope Stability Hazards and Rock Slope Monitoring in Open Pit Mines Surface mining often creates excavation boundaries which are steeper than those would be created under natural processes in the same rock type. They are also undertake quite rapid stress changes during mining and are influenced by significant external forces such as blast vibrations and changes in groundwater. These conditions are likely to allow some degree of instability to develop in the pit slopes. The hazards associated with this instability of pit slopes can be extremely variable in character; ranging from small cobble sized rocks dislodging and falling from mine benches to complete collapse of entire pit walls. It is usually the position of mine geotechnical or geological staff to assess these hazards for mine operations. The assessment of hazards due to unstable slopes can be done by visual observation of precursor signs such as fracturing or rilling of loose material. A more reliable indicator of instability involves the quantitative measurement of outward movement and acceleration of material as an instability mechanism develops. There is strong evidence that small precursor movements of a rock wall occur for an extended period prior to rock slope collapse (Hoek and Bray, 1981). Development of a monitoring system, adopting acceptable slope deformation criteria coupled with warning systems and design of stabilization or risk reduction measures if appropriate has become a standard method of dealing with slope instability. Framework for Slope Hazard Management using the SSR A framework for the management of slope hazards is shown in Figure 1 (discussed in detail in Harries, 2007). Although this framework is specifically for use with the Slope Stability Radar, a similar framework could be developed for other monitoring technologies for monitoring slope deformation. An important point to consider is the sequential nature of the hazard management framework from selecting the context ? identifying hazards ? analysing hazards ? evaluating hazards ? treating hazards. [ ] Once the context of the system has been developed (for example ? to monitor for rapid bench scale collapse), the identification of hazards is the next stage in hazard management. Identification of slope hazards can be relatively straightforward due to the visual nature of the information that the SSR system produces. The areas of excessive wall deformation are highlighted in color maps of the mine slope with a co-aligned photographic image to review the actual site of interest. The responsible personnel must then analyses this data, usually reviewing the deformation style and rate, as well as the size of area that appears to be failing. This information can then be evaluated against organisation protocols (for example it may be only a small sub-bench failure that will be ?caught? by existing benches and hence can be categorized as a lower risk). Once these hazards are evaluated they can then be treated if required. Two major options are available to reduce the risk during this treatment option. We can reduce the likelihood of failure ? for example by buttressing the failure or de-pressurising of water pressures in a slope. However, the most likely plan of action is to reduce the consequence of the failure. One of the most successful opportunities to reduce the consequence of a slope failure is to ensure that no personnel or mining equipment is present at the location of a slope failure when collapse finally occurs. This has been the major benefit of the SSR system to the different mining operations around the world. SLOPE STABILITY RADAR TECHNOLOGY OUTLINE Slope Stability Radar system specifications and capabilities: ? Measurement precision +/- 0.1mm (std.) ? Perforated dish and other features enable it to operate in high wind conditions ? Measurement range is 1700 metres ? Scans 270 degrees horizontally and 120 degrees vertically ? 1 ? 30 minute repeat rate for area scans (varies according to area being scanned ? RF exposure (<0.05mW/cm2) is a factor of 200 below the acceptable limit for the general population (1 mW/cm2) ? Tolerant to vibration and mining equipment ? The system weighs approximately 1500 Kg ? Remote area power supply enabling unmanned, continuous 24/7 monitoring ? Real time monitoring

Jan 1, 2009

By ERIK CHARRIER, ADITYA JUGANDA, Jürgen Brune, Patrick Maier, Gregory E. Bogin Jr

Confined explosions are a major risk in underground coal mine operations. Depending on confinement, ignition location and obstacles in the flame path, methane explosions can transition to detonations. As a result, the severity of mine explosions ranges from minor damage to loss of lives and permanent mine closure. Experimental results have shown that the inclusion of obstacles can significantly increase the flame propagation velocity by inducing turbulence. This research focuses on explosion experiments in a 71 cm diameter, 30.5 m long reactor that includes rock piles as obstacles along with developing the corresponding CFD model that captures the observed flame behavior and interaction with the obstacles. The rock rubble increases the flame front propagation velocity by 500% compared to the maximum velocity observed in the empty reactor experiments. The 2D and 3D CFD models predict the experimental flame front propagation velocity, whereas the 3D model shows a more explicit conformity than the 2D model. Although the computational time to complete the simulation is much less for the 2D model than for the 3D model, the 2D model is not sufficient to simulate cases with rock rubble since it cannot capture the propagation of the flame through the small voids between the rocks with the same effective blockage ratio as the 3D model. The validated CFD model can be scaled up to simulate methane explosions in full scale mine and industrial settings.

Nov 20, 2023

By Lee Browne

The transformation of Peru’s Tintaya copper project from a state-owned company to a private company is under way and the results have been successful. Since Magma Copper Co. assumed operating management in December 1994, production and costs have improved dramatically. To understand the transformation of Tintaya, the transformation of Magma Copper must also be understood.

Jan 1, 1996

By Michelle L. Ramos

INTRODUCTION The Ballard Siphon was built in 1935 and consists of two 91.4 cm (36-inch) diameter wood-stave pipes. These pipes convey sewer flowsunder the Ship Canal from northwest Seattle and the Ballard Regulator to the North Interceptor and the West Point Treatment plant. The siphons were constructed using open cut construction, are now buried in the sediment on the floor of the canal, and have severely limited ability to be dewatered, inspected, or cleaned. The existing siphon is 394.7 m (1,295 feet) long from the junction structure on the southern shoreline to the regulator structure on the north. The location of the Ballard Siphon is shown in Figures 1 and 2. The area around the Ballard Siphon has become more populated and developed since the siphon was built. Additionally, the Ballard Siphon is subject to high flows that are greater than the capacity of the pipelines. This has resulted in predict-able Combined Sewer Overflows(CSO?s) whenever a large, long duration rain event occurs. The aged pipeline of uncertain viability has become a critical piece of the sewer system infrastructure. Because of the age of the pipelines and their importance, a sonar survey was completed on both barrels of the Ballard Siphon in December of 2005. The sonar images appeared to indicate crown intrusion of the wood-stave pipes, which suggested that the pipes were in imminent danger of collapse. As a result, an Emergency Declaration was executed by King County and the Ballard Siphon Replacement Project was initiated. Staheli Trenchless Consultants was retained to perform feasibility studies to deter-mine the viability of using microtunneling and horizontal directional drilling (HDD) for replacement of the Ballard Siphon. For the evaluations, the preferred site location was determined to be at or near the site of the existing Ballard Siphon in order to minimize the ancillary sewer work which would accompany moving to a new site. To meet flow demands and hydraulic requirements, the replacement siphon needed a mini-mum equivalent diameter of 182.9 cm (72 inches). This could be accomplished with a number of different siphon diameters and configurations including, but not limited to, three 106.7 cm (42-inch) diameter pipelines, two 152.4 cm (60-inch) pipelines, or two 91.44 cm (36-inch) pipelines and a 121.9 cm (48-inch) pipeline.

By M. P. Hoffman

The U.S. Bureau of Mines is developing a roof bolter with a computer-controlled drill head that will increase the safety of roof bolting in underground coal mines by allowing miners to be relocated to a safe area. To ensure secure anchorage, acceleration and strain data are broadcast from an instrumented drill steel to a data acquisition system. These data are analyzed, correlated, and transformed to pro-vide information about roof strata, then are sent to a supervisory computer executing National Institute of Standards and Technology&apos;s real-time control software. The supervisory computer sends setpoint commands to proportional-integral-derivative control loops to control drill thrust, position, revolutions per minute, and torque.

Jan 1, 1994

By T. R. Kostecki, A. J. S. Spearing, A. Hyett, M. Gadde

Ground control research for underground coal mining has progressed significantly over the past several decades. With this progression, and the ability to analyze and model underground conditions, underground working conditions have significantly improved. In order to progress further, the behavior of roof support must be known and be adequately modeled, such that models can be used for support design under different geological and mining conditions. This paper discusses the results from a research project funded by the U.S. National Institute for Occupational Safety and Health (NIOSH) and undertaken by Southern Illinois University Carbondale and Peabody Energy. The research involved installation of active and passive instrumented bolts in mines, recording relevant in situ data and then attempting to model the behavior of the bolts as mining progressed. Such calibrated models could aid in design of roof supports under different geological and mining layouts and thus, hopefully, further improve rock related safety.

Jan 1, 2012

By Snehamoy Chatterjee, Sanjay Kumar Palei, Smarak Das

Machine manufacturers’ recommendations on maintenance strategies of capital-intensive draglines are not always based on real data and therefore lead to losses from downtime. This paper proposes a preventive maintenance strategy for a dragline deployed in an opencast coal mine based on reliability-centered maintenance and failure-mode-effects analysis using real operational data. Reliability-centered maintenance replaced a cluster of critical failure components of the dragline while satisfying two specific conditions: (i) the components should be replaced at the earliest mean time to failure (MTTF) within the group and (ii) the time taken to replace all the parts should be equivalent to the maximum downtime within the group. Estimated threshold weightage factor identified twenty-six critical failure components for the preventive maintenance strategy, and clustering of components divided them into nine groups. In a group, the loss that is expected to occur by replacing some of the components before their failure, and the gain by reducing the overall maintenance downtime, has been explained through a cost-benefit analysis. The total net profit generated is calculated as US$200,178. This clustering activity also led to a reduction of annual downtime by 231 h, whose approximate market price as equivalent coal production costs $295,365.

May 28, 2020

By David R. Maneval

The mining of coal in Alaska receives special treatment in the Surface Mining and Reclamation Act passed by the U.S. Congress in 1977 (PL95-87). Section 708 of the Act required that the National Academy of Sciences (NAS) perform a study of "Surface Coal Mining Conditions in the State of Alaska, In Order to Determine Which, If Any, of the Provisions of the Act Should be Modified with respect to Surface Coal Mining Operations in Alaska&apos;. The special committee on Alaskan Coal Mining and Reclamation of NAS completed their study in 1980 and prepared their report (NAS, 1980). At this time, the Secretary of the Interior and the Congress have taken no special action with regard to either special regulations geared specifically to Alaska or to submitting special draft legislation to the Congress requesting amendment of PL95-87. The Alaska Department of Natural Resources (DNR) has drafted legislation which was submitted to and passed by the 1982 session of the State Legislature. The State regulatory agency has also drafted the requisite regulations necessitated by the amendments to the State&apos;s Basic Coal Mining Act. It is expected that by mid 1983 DNR will have applied for "primacy" to the office of Surface Mining, U.S. Department of the Interior (OSM). They will be submitting the amended State Law, the revised State Regulations and an operational plan as called for by OSM regulations. The presumption is that primacy will be granted to the State of Alaska under PL95-87. The Usibelli Coal Mine continues to be the only operational commercial mine for coal in the State of Alaska. It produced 7.26 x 10 kg (8 x 10 " T) of coal during 1981. The current mine was started in 1920 by Captain Lathrop, an early developer and pioneer in Alaska. It was continued by Emil Usibelli and was taken over after the death of E. Usibelli (in the 1964 earthquake) by his son Joseph Usibelli who is the current President of, the firm3 Their latest improvement is a 27.5 m (36 yd. )Bucyrus-Erie Dragline which handles most of the overburden removal. The coal is removed by a loader-truck combination. They are currently starting up the use of a unit train loading facility which handles forty cars every two hours. This loading system was a development necessitated by the Sun Eel Export contract. The Alaskan Railroad was a major cooperator in the development of the first unit train loading facility in Alaska.

Jan 1, 1982

By H. Mischo, F. Daniela, L. Schaarschmidt, I. Paschke

In order to safely store radioactive waste long-term, HAW repositories in saliferous formations have to be backfilled. The main purpose of those backfill operations is the restoration of the geological barrier function of the containment area. For best possible results the used material should be of a comparable composition or characteristic for the host rock formation. Additionally, the material should show a high density after completion of the backfilling process as well as a low permeability. A major aspect to consider in these processes is the minimization of the gap of the backfill body to the roof of the drift. To fulfil those requirements, a micro-structure stabilized crushed salt backfill material has been developed as part of the GESAV-I-project. Due to the material composition of this so-called GESAV-material, salt mineralcrystallization processes start after emplacing it, a process that leads to the polyhalite formation. With the crystallization of polyhalit, the halite grains are bridged, which in return stabilizes the matrix of the backfill. The GESAV-II-project continued successfully what GESAV-I started and determined an ideal backfill method in order to build the backfill bodies composed of GESAV-material. Due to the compaction of the material during emplacement by vibration, high in-situ densities, low permeabilities and a backfill factor close to 1 was able to be reached. In the following SAVER project this journey of practical test underground will be continued.

Mar 2, 2022