Search Documents

By Harold J. Schock

The cases of no auxiliary ventilation and ventilation with tubing were mathematically modeled, using a turbulent dispersion model. The scooptram that is used to load is modeled as a variable-speed, variable-strength source of pollutants moving in and out of the dead-ended drift. Model predictions are compared to experimental measurements. A parametric analysis was performed to determine the effect of exhaust pipe location and time spent out of the drift, as well as to determine if a relationship existed between CO2 and NO levels. It was concluded from this analysis that when modeling a load-haul-dump cycle, it is necessary to use a model that has the capability of predicting changes in source strength as well as source location. It was also determined that four relevant factors include effective heading height, apparent longitudinal diffusion coefficient, transverse concentration gradient at the face, and average dispersion width of the exhaust jet. As these factors change with heading geometry and ventilation configuration, they were determined experimentally, Carbon dioxide was used as a tracer to calibrate the model; since, knowing the fuel flow rate, it is possible to calculate CO2 production. The above four factors in the computer model were calculated using a regression analysis, comparing predicted local concentrations to measured local concentrations. The model was then verified after this calibration process using additional experimental results. With the calibrated model, it is possible to predict pollutant concentrations at any location in the heading using an engine map and the previously calculated flow field. A parametric analysis shows that the exhaust pipe location can have a significant impact on operator exposure to exhaust gases. It was also shown that NO concentration varies directly with C02 levels. Predictions using the dynamic model are contrasted with constant source strength (pollutant flow rate) results. An analysis of these predictions for computing time-weighted average NO shows the dynamic model predictions of operator exposure to this pollutant to be less than one-half of the value predicted using a constant source model.

Jan 1, 1981

By Y. J. Wang

The selection of a shaft size for ventilation purposes is a classic problem of concern to mining engineers. This presentation is concerned with the sizing of conventionally-sunk circular shafts with concrete or shotcrete linings. Costs of sinking shafts of three different depths (from 500 feet to 1000 feet) and six different diameters (from 14 feet to 24 feet) were obtained through questionnaires to shaft contractors. The primary objective of the economic model presented is the balancing of detailed annual capital and operating costs to achieve the minimum overall cost of the shaft installation over its life. The economic model is similar to previous analyses but treats several of the individual cost categories in an updated fashion. Included in the paper is a detailed analysis of the effects of varying power costs on optimal shaft size. Also included are a statistical analysis of current shaft costs and comments on the choice between shotcrete and concrete linings.

Jan 1, 1977

By H. H. Murray

Recently developed clay deposits that will impact regional and world markets are described. These deposits, their location, geology, and physical properties are delineated. Kaolins from the State of Para in Brazil and from Ukraine; bentonites from Argentina and India; and palygorskite and sepiolite from China are world class deposits that when processed using modem technology will produce excellent products. Other deposits that may affect regional markets are kaolins from China, Australia and Indonesia; bentonites from Georgia (formerly USSR) and China; and palygorskite from India and Ukraine. New ball clay deposits that will affect regional markets are in China and Indonesia.

Jan 1, 1999

By K. M. Kim

A site-specific blasting model has been developed for the Asarco Mission mine. The main inputs to the model are the in-situ block size (F80), the post-blast fragmentation (P80) and the intact tensile strength (To). The output from the model is the specific blast energy (ESE). Modern techniques are being used to obtain the input parameters for the site-specific blast fragmentation model. In particular, image processing software is used to obtain both the in-situ block size and the post-blast fragmentation, and the Schmidt hammer is used to obtain the tensile strength at numerous locations throughout the rock mass. An initial model was developed using five test shots in one area of the mine that contains Argillite and is relatively homogeneous. This also included calibrating Schmidt hammer readings against actual Brazilian tensile measurements. The model for Argillite will be updated as more tests are conducted, and the model will be extended to the other four primary rock types at the Asarco Mission mine.

Jan 1, 2011

By Shailendra Chawla, Ashok Jaiswal, B. K. Shrivastva

The study aims to evaluate the pillar behavior during the depillaring operation by continuous miner (CM) technology. A panel with five headings developed as per the coal mine regulation of Indian coal mines [2] has been selected for the study. The depillaring operation has been carried out using CM technology after widening and heightening the original entries. An extensive field investigation has been carried out throughout the depillaring operation to access the mining conditions. Depillaring operation has been performed smoothly up to the middle of the panel (fourth row out of eight rows of four pillars each). Advanced blinking of the auto warning tell-tale (AWTT ) has also been observed on some of the instruments during the splitting of pillar no. 18. The panel shows extremely difficult mining conditions at this stage. The case has been numerically simulated using three-dimensional numerical techniques. The simulation result has indicated the high stress and yield condition on the working and the barrier pillar (surrounding goaf from both sides) after the extraction of pillar no. 18. The analysis has also indicated the marginal stability of the 2nd barrier pillar (namely “pillar B”). The failure of the barrier pillar could be the responsible for global instability of the panel as observed in the field. Understanding the importance of the barrier pillars, panel design has been modified by incorporating an additional row of barrier pillars. The stability of the modified panel has been evaluated. Both working and barrier pillars have been observed stable in the modified panel. This could be an alternative layout considering safety at the working face.

May 8, 2022

By Kanhaiya Mishra, Phanil. K. Mandal, S. K. Behera, P. S. Paul, Prashant Singh, C. N. Ghosh

The techno-economic and social benefits of cemented paste backfill (CPB) resulted in its wide acceptance by the mining industry. The Ordinary Portland Cement (OPC) remains the key binder but to diminish its economical constraints, suitability of alternate binders has been examined worldwide. The present study aimed to investigate the effect of partial replacement of OPC with fly ash on the CPB’s strength and to determine the most optimal mix to achieve the required strength (1 MPa at 28 days of curing) at the most cost-effective way using the Bayesian network (BN). The CPB mixes were prepared at 72 wt.% solid concentration with mill tailings (87–91%), OPC (6–13%), and fly ash (0–4%), and instantly after mixing, fresh (slump, bleeding, density) CPB properties were measured. The strength was tested at 7, 14, 28, and 56 days of curing and initially analysed through traditional model. The traditional models follow the aleatory principle and are considered not appropriate for geotechnical engineering. Hence, the BN model was developed and tested. The reliability of two classifiers in learning model structure was compared which gives Naïve Bayes as the highest reliable tool. The CPB’s strength is most sensitive to the OPC content. The most consistent mix(s) is mill tailings: 87–88%, OPC: 9–11%, fly ash: 1–4%. Adding fly ash at 89–91wt% mill tailings possesses high failure probability of the CPB. The collinearity test indicates that the fines percentage and chemical composition of CPB’s ingredients are highly correlated with its slump, bleeding, and strength development.

Jul 14, 2022

By John F. Beesley

INTRODUCTION This paper discusses the design of the subsurface nuclear waste repository at Yucca Mountain, Nevada; and possible concepts for construction of the subsurface facility. Subsurface construction at Yucca Mountain is planned to last for 20 or more years, and may be accomplished using tunnel boring machines (TBM), drill and blast methods, raise bore machines, and roadheaders. The design of the subsurface facility includes approximately 107 km (66 miles) of tunnels and drifts. The vast majority of the repository will be excavated with TBMs. Design and construction concepts for the subsurface repository discussed in this paper are based on the License Application that was submitted to the U.S. Nuclear Regulatory Commission (NRC) by the U.S. Department of Energy (DOE) on June 3, 2008. The License Application was subsequently docketed by the NRC in September 2008. When a Construction Authorization is received from the NRC, notices to proceed with subsurface construction at Yucca Mountain will be issued by DOE. The Yucca Mountain site is located in the Mojave Desert approximately 150 km (90 miles) northwest of Las Vegas, Nevada. The site is on federal land in southern Nevada and is shown in Figure 1. Yucca Mountain is a ridge of volcanic rocks com-posed primarily of solidified volcanic ash. Previous underground construction work at Yucca Mountain included excavation of two tunnels using two different TBMs. The first tunnel, the Exploratory Studies Facility (ESF), is a 7.62 m (25 ft) diameter tunnel that is 7,877 m (25,843 ft) long and was described by Morris and Hansmire at the Rapid Excavation and Tunneling Conference (RETC) in 1995. The second tunnel, known as the Enhanced Characterization of the Repository Block (ECRB), was a TBM drive of 5.0 m (16 ft, 5 in.) in diameter and 2,681 m (8,796 ft) long. The second tunnel was excavated in 1998 and was described by Fulcher, Eastlund and Copeland at RETC 1999 and is named the East?West Cross Drift in that paper. (These previously excavated tunnels are shown in Figure 2.) In the volcanic rock formation where the vast majority of the planned repository will be con-structed, previous tunneling conditions were generally very good.

By Steve Kral

About 500 mineral-processing professionals from around the world gathered in San Francisco, CA in Oct. 22-27, 1995 for the XIX International Mineral Processing Congress (IMPC). Following the theme “Leading Mineral Processing into the 21st Century Through Advanced Technology,”186 speakers from 28 countries covered research and development activities and innovative processes. Subjects included comminution and simulation control, physical and chemical processing, flotation practices and fundamentals, precious metals processing and mineral waste and the environment.

Jan 1, 1996

By DEVY DYSON, Brian Hart, JOHN LANGHANS, Stamen Dimov, STEVE YOPPS

A recent Nevada Gold Mines research program focused on pressure oxidation pre-treatment of a Carlin-type double refractory ore from the Turquoise Ridge Mine. The research team found that both arsenian pyrite and carbonaceous matter were highly oxidized within an hour at 300 °C using a bench-top autoclave reactor and that the gold recovery from the residues after cyanide/carbon-in-leach approached the technical limit set by the amount of gold encapsulated by silicate minerals. Although the 60-min pre-treatment at 300 °C yields robust performance when treating a whole ore, copper additives can catalyze the oxidation rate of carbonaceous matter and reduce the residence time needed at elevated temperature. Certain gangue minerals are susceptible to dissolution in acidic solutions at 300 °C, and this may cause poor gold recovery. This recovery challenge is mitigated by keeping free acid in the discharge solution below a key threshold.

Jun 21, 2022

By John C. Draper

Little precise information is available on the effect of mining on the surface topography. It is often assumed that after mining the surface will simply sink. This is not an infallible conclusion as is well illustrated in two of the three examples herein. This paper describes the results of an attempt to precisely measure the surface movement in the area around coal pillars left in place for three oil wells in a completely mined and caved area at the Harwick Mine of the Duquesne Light Company. The dates when the various measurements were made are shown on the data sheets and indicate the rate of surface movement. These oil wells are identified as wells Nos. 2, 3, and 6. This mine property is located on the north side of the Allegheny River at Cheswick, Pennsylvania, and extends in a northerly and westerly direction about five miles. The three well pillars are situated on the westerly side of the Bessemer and Lake Erie Railroad some 2,000 feet from Rural Ridge, Pennsylvania (Fig, 1).

Jan 1, 1964

By N. S. Kim

Economically favored Cr and Cu leaching out process from spent power plant fly ash (PPFA) had been investigated. PPFA, bearing of C, S, V, Ni, Cu and Cr, has been widely used as an assistant fuel in cement industry. Recent environmental regulation in S. Korea prohibits using PPFA as a fuel. Many researchers have also studied on extraction V and Ni from PPFA. Due to low concentration of V and Ni, 2% and 1%, respectively, economical and environmental friendly process could not be found. In this study, Cu and Cr have been removed in an economical way and which satisfied with KS Extraction Test. The rest unburned carbon, V2O5 and NiO2 in residue were found to be applicable for indoor and outdoor colored bricks or deodorant panel. Various parameters such as pH, lixiviates and time on leaching behavior were investigated in order to leach Cr and Cu remaining C, V and Ni. Keywords: Fly ash; Selective extraction; Ammonia; Deodorant panel

Jan 1, 2009

By Jaisen Kohmuench, Michael J. Mankosa

Flotation has long served as the foundation for sulfide mineral recovery. As ore grades decline, however, this traditional approach is being pushed to the limit. Nowhere is this more evident than in the challenge of recovering coarse, partially liberated particles — an area where conventional flotation systems typically underperform due to excessive turbulence. As a result, valuable coarse minerals are often lost to tailings. Fine grinding has become the default solution, although with the added burden of higher operating costs and more challenging tailings disposal. To address the challenge of coarse particle recovery, Eriez developed the HydroFloat, a technology that uses a novel fluidized-bed approach to extend the upper particle size range of flotation significantly. The HydroFloat can recover particles exceeding 0.5 mm in diameter with a sulfide surface expression as little as 2 percent. Coarse particle recovery allows for optimization of comminution circuits for coarse gangue rejection before fine grinding. A substantial increase in overall tailings particle size provides higher water recovery due to improved drainage and allows for consideration of a dry, stacked tailings option instead of a tailings dam/impoundment. The technology’s transformative potential has not gone unnoticed. In recognition of its impact, Eriez was honored with the 2024 Robert E. Murray Innovation Award, commonly referred to as the Murray Award, by the Society for Mining, Metallurgy & Exploration. This prestigious award was established in 2017 to recognize organizations that advance the mining industry through the implementation of technical innovation. The HydroFloat stands as a fitting example of how creative thinking and industry collaboration can solve long-standing technical challenges.

Oct 1, 2025

By Andrew Stafford, Kate Willa Brown Requist, Eric Lutz, Simon Lotero Lopez, Moe Momayez, Jeffrey Gordon

This formal literature review identifies strengths and shortcomings of current literature related to mine rescue, self-rescue, and self-escape technology. Key concepts and factors that influence the decision making behind mine rescue and self-escape were identified. Historically, underground mining has been one of the most dangerous occupations due to the harsh nature of working environments. During the latter half of the twentieth century, and into the twenty-first century, mining fatalities have declined, yet large-scale mine emergencies persist. The emergence of new technologies, in combination with evidencebased mine emergency research, is resulting in new training methods, monitoring systems, and self-escape approaches being tried in operating mines. This review identifies areas in which substantial research is being conducted, such as the use of virtual reality and game-based training and areas that warrant further development such as the measurement and information gathering capabilities of unmanned ground and aerial vehicles, as well as emergency management and incident command systems. This paper summarizes the current underground mine rescue and self-escape landscape in the USA, including the breadth and depth of mine rescue and self-escape training and practices as evident in the literature.

Nov 2, 2023

By Cary Hirner

The Metropolitan Water Reclamation District of Greater Chicago (District) is in the final phase of completing the Calumet System component of the Tunnel and Reservoir Plan (TARP) by bringing the Thornton Composite Reservoir online by 2014. The Thornton Composite Reservoir will provide nearly 30 billion liters (7.9 billion gallons) of additional storage for minimization of combined sewer overflows(CSO) and flooding in the Chicago metropolitan area. The project requires that the existing 6.7 m (22 ft) diameter Thorn Creek tunnel conveying overbank flood flows is re-routed and connected to the Thornton Composite Reservoir. This paper presents the components of the Thornton Composite Reservoir and specifically the detailed evaluation of a drill-blast tunnel. Other project features include an access shaft, control gate, energy dissipating structure, bulkheads, and live tunnel connection. The construction contract will be procured in late 2009.

By FELIPE SÁNCHEZ, PHILIPP HARTLIEB

Innovation plays a critical role in the mining industry as a tool to improve the efficiency of its processes, to reduce costs, but also to meet the increasing social and environmental concerns among communities and authorities. Technological progress has also been crucial to allow the exploitation of new deposits in more complex scenarios: lower ore grades, extreme weather conditions, deeper deposits, harder rock mass, and high-stress environments. This paper discusses the importance of innovation for the mining industry and describes the mechanisms by which it is carried out. It includes a review of the drivers and actors involved and current trends. The digital transformation process that the industry is going through is analyzed, along with other relevant trends that are likely to shape the mining of the future. Additionally, a case study is presented to illustrate the technical and economic implications of developing a disruptive innovation project.

Jul 23, 2020

By Leping Liu, Li‑Ting Chen, Sachin Urade, Pengbo Chu

Mining industry requires constant adaptation to its practices in response to the dynamic change of the societal demand. Little information exists regarding how the US metal mining engineering education is prepared to meet with its industry needs due to the increase in critical minerals driven by the green energy transitions. This study aims to provide industrial perspectives on the current US metal mining engineering education and areas for improvement. An online survey with both closed- and open-ended questions were designed to seek opinions from the US mining industry. Findings indicated a shortage of qualified graduates from the current US metal mining engineering education system. The qualifications need to be improved include engineering sciences underlying mining methods, mining design experience, mining feasibility study, the connection between theory and practice, and understanding of the overall mining operation. The survey also identified future desired qualifications. The most desired ones in the next 5 years include an ability to acquire and apply new knowledge as needed and sufficient experience in the field. Respondents, regardless of the nature of their affiliated mining companies, unanimously recommended that collaborations between the industry and academia should be enhanced. The analysis of the results concluded four recommendations: (1) involve more multiple stakeholders in reforming mining education programs, (2) reinforce field experiences as a key part of mining engineering education programs, (3) enhance a closer collaboration between academia and industry, and (4) integrate emerging technologies (e.g., artificial intelligence/virtual reality) guided by pedagogical theories into new mining engineering curriculums.

Jun 26, 2023

By R. S. Shepard

The closing remarks of a paper which I presented at the annual AIME meeting at Dallas, Texas during February of 1963; contained a forecast of increased activity in trackless underground ore mining which finalized that presentation. At that time, HAD I been peering through my brightest rose colored glasses, I could not have foreseen the unprecedented rapidity of acceleration of underground ore mining methods which has since ensued. From Death Valley, California diagonally to St. Johns, New Foundland; from Australia to Africa to Sweden to France and Germany; from South America to Southern Mexico to Northern Saskatchewan and Northern Manitoba the expansion of trackless underground ore mining methods has probably progressed at a faster rate than any other revolutionary' change in the history of underground ore mining.

Jan 1, 1967

By D. Brosnahan, J. Gathje

Newmont Metallurgical Services (NMS) recently acquired a Scanning Electron Microscope (SEM) with a JKMRC/FEI Mineral Liberation Analyzer (MLA). With the MLA software package, raw particle image and X-ray data can be converted into particle mineral maps and bulk and liberation data can then be calculated for minerals of interest. This type of quantitative mineralogical data can then be used for a wide variety of applications. Ore characterization with MLA can be carried out for existing or processing plants in development. MLA characterization of laboratory test products provides valuable liberation information that assists the research metallurgist in better planning and developing process treatment options for various ore types. This paper describes the use of MLA characterization in a copper flotation test program where the use of various testing options for arsenic depression was being evaluated.

Jan 1, 2007

By J. Drzymala

Particle beneficiation tests are often conducted to determine how the recovery of a key component of a particle mixture varies with overall product yield, i.e., the separation curve. The results can be misleading when an attempt is made to determine the effect of feed grade by comparing separation curves representing different feed grades or key component concentrations. This is a shortcoming of the conventional recovery versus yield diagram, which may not appear to be affected by feed concentration. To overcome this shortcoming, a method is presented for transforming and normalizing the recovery and yield coordinates so that the separation curves representing dif-ferent feed concentrations are directly comparable.

Jan 1, 2007

By Robert S. Shoemaker

The development of a metallurgical project is a business venture rather than a technical exercise, and its real objective is to obtain the maximum return on investment consistent with the limitations imposed by company policy and the requirements of society. Demand for profits is the driving force for technical advances and naturally leads to improvements in processes, equipment and plant designs. In the mineral dressing field there have been virtually no new processes developed since the introduction of flotation, and the steady erosion of profits by inflation has been offset only by increasing equipment size. Unfortunately, in recent years, plant designers have not always utilized the largest equipment or the opportunities for functional and economic design presented by the development of larger equipment. Lower cost plants can be developed providing that unrealistic restraints arising from the prejudice of past practices are avoided. As an illustration of this premise, three different approaches were taken toward the design of a clearly delineated but hypothetical copper concentrator of 20, 000 tons per day capacity. While the same flowsheet was used in each case, designs were produced for a conventional plant, an alternate using the largest available equipment, and a third scheme utilizing large equipment and the most functional design which could be developed, including features derived from many plants in many different industries. Capital costs were developed for the three separate designs based on a location in the southwestern United States. Ancillary facilities were identical in each case and included a mine truck shop, a maintenance shop, a general office, and a nominal starter dam for tailings disposal within 5000 feet of the plant. Water supply within 1000 feet of the plant, and power furnished to the property boundary has been assumed in each case. The flowsheet of the three plants is shown in Figure 1 and represents the treatment of a typical sulfide copper ore by three- stage crushing followed by single-stage ball milling. Concentration is by flotation roughing and scavenging followed by regrinding of the concentrates and two stages of cleaning.

Jan 1, 1971