Search Documents

By Dong Yang, Jicai Han, Xiaoshuang Guo, Tichang Sun, Zhengyao Li

Straw charcoal was used as a novel reductant in the co-reduction roasting of laterite ore and red mud. The influence of the reductant dosages, co-reduction temperature, and co-reduction time were investigated. Results showed that a powdered ferronickel product of 1.81wt.% nickel and 81.40wt.% iron was obtained under straw charcoal dosage of 15wt.% and roasted at 1250 °C for 80 min. The corresponding recovery of nickel and total iron were 97.21wt.% and 98.87wt.%, respectively. The performance of straw charcoal was also compared to that by the conventional coke reductant. Results showed that ferronickel particles using straw charcoal were larger in size than coke, mainly due to the lower S (0.14wt.%) and ash content (3.80wt.%), which could not hinder the agglomeration of the ferronickel grains, and lower melting point that producing liquid phase and promoting ferronickel particles growth. In addition, the gasification reactivity of straw charcoal is better than that of coke, which is beneficial to the iron oxide reduction and the recovery of iron. To conclude, straw charcoal is a promising reductant for the co-reduction of laterite ore and red mud in coal-deficient areas.

Aug 12, 2021

By T. Klemetti

Moisture deterioration of clay-rich roof rocks causes high numbers of roof falls in coal mines in humid summer months. Rocks with high moisture content are generally weaker and can further deteriorate when subjected to wetting and drying cycles. As a result, it is important to evaluate the moisture-sensitivity of roof rock prior to mining. The National Institute for Occupational Safety and Health (NIOSH) has evaluated three moisture-sensitivity index tests on roof rocks from 23 U.S. coal mines. The three tests were the University of Kentucky Weatherability test (Weatherability test), the Consol Energy Water Sensitivity test (Water Sensitivity test), and the NIOSH Immersion test (Immersion test). Of these three tests, the Weatherability and Water Sensitivity tests are more reliable in classifying the moisture-sensitivity of roof rocks. Disclaimer: The findings and conclusions in this report have not been formally disseminated by the National Institute for Occupational Safety and Health and should not be construed to represent any agency determination or policy.

Jan 1, 2009

By T. Mudder, R. Cellan, R. Waterland, J. Whitlock, B. N. Nelson

The effectiveness of anaerobic in-situ biological treatment for the immobilization of selenium, molybdenum, and uranium in an alluvial aquifer was examined using long-term column tests. A series of organic substrate and nutrient combinations were tested to determine removal effectiveness, optimum supplement concentrations and ratios. Final column testing was conducted to determine the chemical stability of the treatment by-products/treatment compounds by dosing the columns continuously with elevated redox untreated alluvial groundwater.

Jan 1, 2002

Those involved in the mining and minerals industry really are an optimistic bunch. Faced with an economic downturn that has spread across the globe ? one, some say, that crept up on everyone ? mining professionals remain hopeful that the industry will return. An example of that optimism is the attendance at two of the industry?s key conferences and exhibitions. In February, more than 4,200 people attended the SME Annual Meeting and Exhibit in Denver, CO. And a week later, in Toronto, Ontario, more than 18,000 were on hand for the Prospectors and Developers Association of Canada?s (PDAC) meeting. Both are respectable numbers and run contrary to meeting attendance figures during previous downturns when attendance and the numbers of exhibitors fell off significantly. Like other downturns, this most recent one has resulted in massive layoffs, curtailments of production and outright closures. Exploration has been hard hit and many junior mining and exploration companies will either disappear or be swallowed up by others. Gold is its usual self The PDAC generally attracts the gold mining and exploration sectors. So that might explain some of the optimism at the meeting. Unlike base metals and construction materials, gold, not surprisingly, is doing well. And most of the companies in the Investors Exchange at PDAC were involved with gold. While the balance sheets for most base metals companies look bad, gold companies appear to be not as hard hit. Gold is doing what it usually does during a downturn ? act as a safe haven while the value of other assets collapse worldwide. Governments around the world are preparing to pour trillions of dollars in an attempt to resuscitate their economies. This will likely lead to inflation, some experts at the PDAC convention said, which will be good for gold. And gold mining companies are also benefiting from lower production costs. The result is that some gold watchers believe gold could reach $64/g ($2,000/oz) at some point.

Jan 1, 2009

By C. Strachan

This paper presents an evaluation of tailings dam incidents from the 1994 USCOLD Tailings Dam Committee report. Comparisons are also made with water storage dam incidents from USCOLD reports and recent tailings dam incidents. The evaluation results show that tailings dam incidents are due to a number of factors including overtopping, static and seismic instability, seepage and internal erosion, and foundation conditions, and that no particular type of tailings dam or operational condition is more susceptible to incidents. In addition, the results confirm that tailings dams should be located, designed, operated, and reclaimed with a thorough knowledge of site conditions, mill operation, site monitoring, and tailings characteristics.

Jan 1, 1999

By S. Mohanta, S. Chakraborty, B. C. Meikap

"An air dense medium fluidized bed separator is an efficient dry process for the removal of undesirable gangue material from run-of-mine coal. Its cleaning performance depends on a variety of operating parameters that are interrelated in unknown, complex ways. A literature review showed that these parameters' effects had been experimentally investigated using a traditional one-variable-at-a-time approach, which is highly inefficient and sometimes misleading because many of the parameters often interact with each other to alter the overall equipment performance. Also, it is realized that the interrelationship among these parameters can have a significant effect on equipment performance. Therefore, to correctly evaluate the effects of individual parameters as well as their interactional effects on the separation performance of an air dense medium fluidized bed, we conducted a scientific study based on response surface methodology. Empirical models for two key response variables, namely, product ash and combustible recovery, were developed and subsequently used for identifying an appropriate operating region to achieve optimum separation performance. Furthermore, the optimum performances predicted from the empirical models were validated against experimental data. Preliminary results show a strong interaction among the operating parameters investigated in this test program.IntroductionFluidization is widely applied in industry for its various useful features. In the coal industry, it is used in the air dense medium fluidized bed (ADMFB) separator for the beneficiation of run-of-mine coal. In this separator, a medium is created by suspending fine magnetite particles in an upward air flow, and this pseudo-fluid is used as the beneficiation medium, with the lighter coal particles floating to the medium’s surface while heavier particles sink to the bottom. This separation technique had been receiving a significant amount of attention worldwide in recent times for its specific advantages of low operating cost and less restriction for small capacities (Luo and Chen, 2001; Sahu et al., 2009; Dwari and Hanumantha Rao, 2007; Van Houwelingen and de Jong, 2004), but it is still not a well-established industrial practice because of the availability of efficient wet processing technology. However, with a revival of interest in the dry beneficiation of coal, in general, and ADMFB, in particular, there is once again a concerted effort to improve the efficiency of the ADMFB process, and successive improvements have been made to make this process a competitive and viable option. The existing literature reveals that most of these research efforts had been essentially focused on the identification of a single parameter that has a key influence on separation performance, without taking notice of parameter interactional effect. For example, Luo et al. (2004) proposed a pressure drop number to distinguish separation performance without considering the bed height and gas velocity, which are intimately related to this proposed pressure drop number."

Jan 1, 2015

By William A. Macaitis, Frank E. Dalton, Leo R. DiVita

The Metropolitan Water Reclamation District of Greater Chicago's Tunnel and Reservoir Plan (TARP) is a multi-purpose urban public works project with a total cost of $3.7 billion. Currently 51 miles of TARP tunnels are completed and operational and 34 miles are under construction. The excavated TARP tunnels have been constructed in rock utilizing 29 tunnel boring machines, ranging in size from 6.5 to 35.3 feet in diameter.

Jan 1, 1993

By Howard W. Adam

Mill length was the primary variable investigated in an autogenous pilot mill circuit. The 5-1/2' diameter mill had both pebble ports and 1/2" wide slotted grates. The plus 1/2" mill product was crushed in a cone crusher and returned to the mill feed along with the minus 1/2" plus 4 or 6 mesh fraction. Tests were run with a short mill, inside length of 26-3/8", or diameter-to-length ratio of 2.50 to 1. The same mill was then lengthened to 48-3/8", diameter-to-length ratio of 1.36 to 1. The effect of mill length on circuit product characteristics was studied. Results show that (1) circuit throughput or grinding rate is lower per foot of mill length in the longer mill, (2) the long mill product is finer than the short mill product, and (3) KWH per ton of circuit product is slightly higher with the longer mill; however, KWH per ton of minus 200 mesh material (finer fraction) produced is essentially the same in the long mill as the short mill, It is not known whether the relationships found for the pilot mill are valid for commercial size mills.

Jan 1, 1973

By J. A. Botín

NPV is a static measure of project value which does not discriminate between levels of internal and external risk in project valuation. Due to current investment project?s characteristics, a much more complex model is needed: one that includes the value of flexibility and the different risk levels associated with variables subject to uncertainty (price, costs, exchange rates, grade and tonnage of the deposits, cut off grade, among many others). Few of these variables present any correlation or can be treated uniformly. In this context, Real Option Valuation (ROV) arose more than a decade ago, as a mainly theoretical model with the potential for simultaneous calculation of the risk associated with such variables. This paper reviews the literature regarding the application of Real Options Valuation in mining, noting the prior focus on external risks, and presents a case study where ROV is applied to quantify risk associated to mine planning.

Jan 1, 2012

By D. Washington

The US economy and the demand for nonfuel minerals grew at lower rates in 1995 than in 1994. Demand for major metals, such as aluminum, copper and steel, was mixed but relatively stable. The building industry, including highway construction, helped to support modest overall growth in demand for industrial minerals. The value of processed materials of nonfuel mineral origin produced in the United States during 1995 was estimated to be $395 billion, an increase of almost 10%compared with 1994 (Fig. 1). The estimated value of US raw nonfuel minerals production during 1995 was $38billion, about 7% more than in 1994. The value of US minerals production has increased in 30 of the last 35years.

Jan 1, 1996

By A. Moergeli

The Swiss are building the world’s longest tunnel, the 57-Kilometer (35-mile) long Gotthard Base Tunnel. Lot 252, Tunnel Amsteg: Two Hard Rock Tunnel Boring Machines (TBM) crossed hydro-thermally decomposed granite. While the East TBM advanced slowly but steadily, the West one got stuck for five months and had to be recovered by special means and methods. Both TBMs have finished their more than 11-Kilometer (7 miles) long drives successfully. Lot 360, Tunnel Sedrun: For the first time in tunneling, roadway support machines are used through most challenging, squeezing geology. They constantly advance in full face mode for about one Tunnelmeter/24 hours.

Jan 1, 2007

By I. Duckworth

P.T. Freeport Indonesia operates a mining complex located in the highlands of Papua, Indonesia. This district consists of underground and surface operations. The East Ertsberg skarn system (EESS) is one of the major orebodies in this district. Subsurface caving of the EESS has been carried out in a systematic series of mining lifts dating back almost 30 years. Present production from the third lift deep ore zone (DOZ), has reached 80 kt/d (88,000 stpd) during 2010, with this rate sustained through 2015. The orebody was proven below the existing caving level, with the next vertical block called the deep mill level zone (DMLZ).

Jan 1, 2010

By S. Bargigli, S. Ulgiati, M. Raugei, F. Cherubini

Metallic magnesium is mostly used in lightweight alloys in order to decrease fuel consumption in automotive applications. Several different production processes are currently used worldwide, and the magnesium production scenario is changing rapidly, with Chinese production increasingly dominating the world market. For the purpose of this paper, a novel approach to Life Cycle Assessment was applied, in which Material Flow Accounting and energy-based methods (Embodied Energy, Exergy and Emergy Analyses) are integrated and complemented, with a detailed description of the environmental hazards associated with emissions from all the different processes.

Jan 1, 2005

By W. Missildine, J. K. Hrica, I. Benbourenane, T. J. Orr, J. L. Bellanca

Each year, haul truck accidents account for a large portion of mining injuries and fatalities. To better understand why these accidents continue to occur, researchers from the National Institute for Occupational Safety and Health (NIOSH) utilized a cognitive task analysis methodology to identify the user requirements of surface haul truck operators and assess differences in perceptions between operators, managers, health and safety professionals, trainers, and maintenance personnel. Additionally, researchers used the critical decision method to focus on better understanding the cognitive demands, decision-making, and problem solving during nonroutine incidents. The preliminary results of this study identify and explore themes within the broad categories of hazards, skills & expertise, and training and provide detailed accounts of nonroutine incidents such as near-misses, loss of control, and collisions. These accounts reveal insights into operator decision making and event progressions that can then be used to build more realistic training scenarios and address hidden hazards and root causes of these incidents. These results, along with potential solutions offered by study participants, can inform future research and help identify creative interventions that can be used by mine operators to address haul truck safety issues

Mar 2, 2022

By Thomas E. Finch

Engineering mine design encompasses a range of situations, and each situation has its own range of detail and fineness. The most time consuming, and perhaps repetitive design situation involves evaluation of new or alternate mining methods. Many man years are consumed examing alternatives conjured up at all levels of the design team, from the number crunching engineer to the engineering manager. Many alternatives are intuitively disregarded, some are briefly evaluated and thrown out, and many others are started but not completed due to time constraints. All alternatives have similar input characteristics and evaluation procedures. In the design process, production requirements are known and equipment production capabilities are generated to determine the numbers and costs of an equipment type required to match a given situation. The end result is some comparative figure, typically cost per ton or yard upon which a decision is built. The similarity of input data and problem solving techniques lends design to computer solution. Computer aided equipment evaluation is not new to the mining industry. An existing and accepted technique is exemplified with the programs used by truck manufacturers. Given a haulage profile and production requirements, the number of anyone capacity, horsepower, tire size, gear ratio or similar characteristically identified truck can be determined. This information can be outputted in varying degrees of complexity and the results used with equally varying percentages of credibility by design or production engineers. Most engineers are willing to accept-the computer's effort with relief and a desire for belief. Although inherently more complex, the ultimate end of computer manipulation should be total mine design. This is an extremely large step in the evolution of mine design, and not many engineers, including the authors, believe the results would be directly applicable or necessarily correct. As with computer simulations of an operation, total computer design of mines requires such complex and lengthy input that each mine might be manually designed more quickly and cheaply. The existence of computer programs which initially evaluate a mining system or part of the system is upon us, however.

Jan 1, 1978

By Mirjana Boskovic

LKAB’s Kiirunavaara Mine is a sublevel caving iron-ore mine located above the polar circle in northern Sweden. The mine has been proclaimed seismically active since 2008 after a magnitude 3 seismic event, according to Swedish National Seismic Network (SNSN). At that time the Kiruna Mine did not have mine-wide seismic system. Since then, the Kiruna Mine experienced several damaging seismic events of which the largest one on the May 18, 2020. The magnitude, based on the moment tensor inversion results on data from the SNSN as well as seismic stations in Finland and Norway, is estimated to 4.2 ± 0.2 moment magnitude. The seismic event on the May 18, 2020 was located in the middle of the one of the productions areas and caused the major damage in the mine, damaging several kilometres of drifts on six mining levels, some of them beyond the practical repair. These damages affected four of ten production areas on several levels, some more some less. Luckily, no person got injured from the seismic event and the very long aftershock series. An important part in the whole process after the seismic event was information flow and decision-making process. It was very important to keep workers and community informed as that contributed transparency of decision-making and decreased the speculations. Resuming the production in the damaged areas in the safe manner, very soon become main focus for the mine management. It was obvious that not only rehabilitation of the areas is needed to resume the production. It was A MUST to understand the factors behind the seismic event and its mechanism to be able to avoid same situation and prevent seismic event of similar size. Mine engineers had to think outside the box to find the solutions to ‘rescue’ every drift that they could to be able to make good enough base for continued mining of the area. The paper describes actions taken in a very complex process of recovering the area that we from the beginning thought need to be abandon. Seismological analyses of the event on May 18, 2020 and past activity in the area, damage mapping, detailed studies of structures and geology, numerical modelling as well as engineering judgement were used as base for all our decisions how to proceed in attempt to restore mining of the area heavily damaged by 4.2 moment magnitude seismic event, in a safe way.

Apr 26, 2022

By Jean Habimana

Complex and distinct geological units spread along the 7-mile long 30-ft inside diameter Upper Rouge Tunnel CSO Control Project in Detroit, Michigan. Its construction is divided in two tunnel construction packages: The South Tunnel, to be driven in finely laminated weak TG Limy Shale, will be excavated by a shielded TBM with precast concrete segmental lining, while the North tunnel, predominantly in a relatively more competent geologic formation Antrim Shale, will be excavated by a main beam TBM with a two-pass lining system. The adits and deaeration chambers will be excavated by sequential excavation method. This paper addresses the process of selecting excavation methods and lining systems for shafts, tunnels, connecting adits, and deaeration chambers.

Critical safety tools to locate miners underground are featured by several exhibitors at MINExpo. Communication was the buzzword for health and safety products at the 2008 MINExpo, and it is still important in 2012. Products unveiled following the Miner Act in 2006 have been upgraded and improved. Saving lives and reducing injuries through better leadership, planning and practice is the goal of every mine professional.

Jan 1, 2012

By N. K. Bohidar

Evaluation of the stability of a structure under given boundary conditions requires accurate knowledge of the state of stress as well as the mechanism of failure at the critical state of stress. This paper represents a part of the research done by N. K. Bohidar during 1965-1968 for his Ph. D. research in Mining Engineering at the University of Utah. It summarizes the determination of internal stress and failure phenomena around cylindrical openings in viscoelastic media subjected to lateral restraint and vertical uniaxial load. The conditions of lateral restraint and viscoelastic nature of the media represent conditions associated with subsurface openings in rocks. The financial assistance provided to the project from the University of Utah Research (Uniform School Fund), W. C. Browning Scholarship Fund, Earth Science Research Fund, and D. C. Jackling Loan and Scholarship Fund is gratefully acknowledged. The authors also acknowledge the assistance of S. Siugh, W. Jones, and K. McCarter during the project.

Jan 1, 1970

By Tania Schmid, Marco Portal Valdivia, Sandra Nowosad

Today’s mining industry faces rapid transformation driven by automation, climate responsibility, and ESG demands, requiring more than technical expertise. Future mining engineers must blend engineering excellence with key human skills such as communication, leadership, resilience, empathy, adaptation to change, curiosity and lifelong learning. Based on two recent surveys, one to senior leaders with over ten years of experience in the mining industry and a second, focused on understanding the perceptions of young professionals, this paper explores which skills become core competencies by 2030 for navigating complexity, leading responsibly, and enabling sustainable transformation. Furthermore, it also examines how educational institutions can adopt strategies to foster the development of these critical skills, preparing future mining talent for evolving challenges.

Feb 22, 2026