Search Documents

By Mahmud Esad Uluer, Seyed Hassan Amini, Aaron Noble, Matt Shigo

Airborne coal mine dust is an unintended and unavoidable result of coal extraction operations that raises notable health and safety concerns. Modern mining techniques utilize several dust mitigation strategies, and the flooded-bed dust scrubber (FBS) is one such technology used extensively on continuous miners. The conventional static panel filter, instrumental in most scrubber designs, is fundamentally limited in collection efficiencies due to a high clogging rate and a tradeoff between mesh density and airflow rate. To overcome these deficiencies, a novel vibrating mesh panel is proposed. In this study, a laboratory-scale dust scrubber unit was used to investigate the efficacy of concept as compared to that of a static mesh. A statistical design of experiments study was first used to determine the effective vibrational parameters and scrubber operational parameters on dust collection and clogging mitigation. Optimized results from this study were then evaluated against those of a static mesh to determine performance improvement while investigating the mechanisms controlling dust collection and particle department through the scrubber system. Results show that the vibrating mesh conditions and higher water flow rates led to an improvement in the collection efficiency of the scrubber system. Compares to a static-mesh, the vibrating mesh FBS showed a significant reduction in pressure drop across the mesh screen indicating lower air loss through the test duration. Overall, the findings confirm that vibrating filter mesh reduces filter clogging while maintaining high collection efficiencies. This research supports further technological advancement in mine dust mitigation technologies.

Dec 27, 2023

By D. Caiden, C. S. Covil, P. J. Chamley

The paper describes the background to alternative delivery models, drawing on international experience, and introduces Project Alliancing/Contract Partnering, common risks and risk sharing on tunnel projects. A plea for early contractor involvement in design is made before describing some whole life design implications for tunnels. The paper concludes with four short case studies; Channel Tunnel Rail Link in the UK, Hull Waste Water Tunnel in the UK; Island West Sewage Transfer Station in Hong Kong, and the New Southern Railway in Australia.

Jan 1, 2005

By James L. Weeks

Introduction This paper attempts to summarize some of the major criticisms of drug testing. Eight problems with drug testing are discussed. These are: • It does not measure something employers have a reasonable need to know, • It is a distortion of priorities, • Drug use is not known to be associated with increased risk of occupational injuries, • Drug testing is proposed as a dangerously simplistic solution to poorly conceived problems, • In the absence of safeguards, it is unacceptably inaccurate, • In the absence of treatment commitments and confidentiality protection for persons dependent on drugs, it is an unethical practice of medicine, • Drug testing is an invasion of privacy, and • It will have a negative effect on treatment of persons with drug or alcohol dependencies. Employers' need to know It does not measure something employers have a reasonable need to know. It is reasonable for employers and fellow workers to want to know if workers are functionally impaired (intoxicated) while on the job. Drug testing does not measure impairment. It measures the concentration of drug metabolities in urine or blood. Unlike measurements of blood alcohol concentration (BAC), drug metabolites are not correlated with impairment or intoxication. They indicate only drug use in the one to two weeks before a urine sample. And, in some instances, they indicate chronic use. Impairment caused by drug use, on the other hand, occurs immediately and declines rapidly within hours. Drug metabolites may linger for days afterwards. Drug metabolite concentrations in urine are a function of (Morgan, 1984; Schartz and Hawks, 1985; MMWR, 1983): • the amount and purity of drug consumed before taking the test, • when the drug was consumed, • whether the person was a chronic user, in which case a certain amount of drug metabolites would be stored in body fat and slowly released, • the person's metabolic rate, and • for metabolites in urine, any dilution effects of urine. Only the first two factors has

Jan 11, 1987

By Martin Herrenknecht, Karin Bäppler

The last five years have seen a remarkable increase in tunnelling projects in both soft ground and hard rock applications. Part of the increase is a result of recent Research & Development efforts to improve Tunnel Boring Machine (TBM) adaptability, capability and reliability. This paper will review the latest innovations in the TBM industry and explain in detail the results of these innovations followed by a forecast where the technology will take the tunnelling industry in the future.

Jan 1, 2005

By Colin Barratt

The East Side Access (ESA) project is the largest underground rail infrastructure project under construction in New York City, USA. The Manhattan segment of the project is to be mined through rock and consists of 4.1 miles of Tunnel Boring Machine tunnels for track work and mined excavations to house rail switches, air plenums, and other rail facilities. This paper considers different methods for concrete lining, such as the use of fixed forms, adjustable forms, and pneumatically applied shotcrete. The advantages and disadvantages of these methods are discussed and the basis for considering one over the other are illustrated. Further discussions on design development and preparation of documents to facilitate quality and constructability in the field are presented.

By T. R. Ellis

Considerable movement is afoot internationally to rationalize standards and regulations relating to valuations and the qualifications for valuation professionals. In July 2000 the International Valuation Standards Committee released expanded standards, and additional important improvements are planned by 2003. Possible updates to the International Accounting Standards (IAS) and potential adoption of IAS by the U.S. could significantly impact minerals appraisers. Standards designed specifically for mineral asset valuation are under development in Canada and the U.S., with Australia’s internationally respected VALMIN Code providing the benchmark. In the U.S., the all-encompassing Uniform Standards of Professional Appraisal Practice (USPAP) is annually modified and continues to gain deeper acceptance, while the SEC holds fast to its antiquated rule prohibiting reporting of a quantitative estimate and value for non-reserve mineralization. Some important international trade agreements are driving actions to free the trade in professional services. In July 2000, an international workshop was held to initiate discussion on minimum qualifications for appraisers to work internationally. Pressure for uniform minimum qualifications and rules for professionals internationally will continue to build. The U.S. is historically among the slowest countries to implement such initiatives, with its state level licensure barriers having the potential to cause some of its professionals to be stranded in an international backwater. Structural change is needed in Australia’s VALMIN Code to remove conflict with the latest International Valuation Standards. The mineral valuation standards developers of Australia, Canada and the U.S. should work jointly on updating VALMIN for global use.

Jan 1, 2001

By R. Mensah-Biney

The NC State University Minerals Research Laboratory (MRL) and Waste Reduction Partners (WRP) of the Land of Sky Regional Council joined efforts in 2000 to initiate a technically sound and practical program for the management of high-volume coal combustion by-products (CCBs) in North Carolina. The accumulation of CCBs from coal burning boilers throughout the state of North Carolina posed a substantial storage problem, and the area was overripe for an effective management program, which would be environmentally sustainable. In particular, the public utility generators had filled storage ponds on their properties, and the storage overload had grown to critical proportions. Much the same situation existed for paper mill biosolids, which were stored on site in landfill cells along with daily output of CCBs from the mill boilers. A conversion process via the patented pyro-process12 (US Patent No. 5,342,442) to produce synthetic light weight aggregates (LWA) from CCBs and paper mill sludge was conceived to process large quantities of both these waste materials. MRL and WRP initiated and formed a consortium that brought together academia, private industry and state agencies to evaluate the production of LWA by the pyro-process. The industry partners included representatives from the power companies, industrial ash generators, expediters for coal ash products, as well as concrete block manufacturers. It was important to welcome interested parties from not only the western North Carolina area and other parts of the state but also from neighboring states including Tennessee, South Carolina and Georgia. Membership of this consortium evolved during the intervening years to include the following participants and supporters: Progress Energy Carolinas; Duke Energy; Santee Cooper; Full Circle Solutions; Land-of-Sky Regional Council; NC Department of Pollution Prevention and Environmental Assistance; Ecusta Business Development Center; Blue Ridge Paper Products; Jackson Paper and Manufacturing Company; Miller Perlite; Appalachian Products; General Shale Brick; Metromont Materials; Small Business Technology Development Center of the University of North Carolina system and North Carolina State University The initial development program conducted at the Minerals Research Laboratory (MRL) was to formulate an acceptable LWA product, which fulfilled user specifications for light weight concrete block and structural concrete application. Support work and program coordination efforts were furnished by retired technical volunteers in WRP. The work advanced steadily, using proven technologies well established in the mineral industry, to generate a very satisfactory LWA. The consortium then concluded that a more comprehensive CCB conversion program would have more appeal for full scale manufacture and commercialization, if a variety of products from CCB separation were generated. This product assortment would include bottom ash, low carbon fly ash, recovered carbon of high purity, as well as the synthetic LWA. The bottom ash would serve the concrete block market, the fly ash was in demand for ready-mix concrete, and the high carbon product could be pelletized and used as a fuel for reburn or by the steel industry, and the LWA was a sought-after component for light weight concrete applications. After scouting all these potential markets and finding them to be viable, the consortium then inaugurated an integrated pilot plant program for the CCB separation and conversion. The plan was organized in three (3) parts: (1) Phase I ? bench scale evaluation studies (2) Phase II continuous pilot plant evaluation and (3) Phase III ? conceptual commercial plant design including marketing efforts and attraction of business entrepreneurs to build a full scale manufacturing plant. Phase II would serve to validate the process in a continuous mode and produce substantial quantities of products for preliminary marketing efforts and for demonstration-of-use purposes. The consortium agreed to the name, CAROLINA ASH PRODUCTS, (CAP), for the integrated pilot plant program. The products generated might be designated with the CAP label as: bottom ash would be named CAP Granules, low carbon fly ash would become CAP Ash, recovered high carbon product would be CAP Carbon, and LWA would have the name CAP Stone. Phase II of the program processed 20 tons (18 t) of ponded ash from Progress Energy storage at a rate of 600 lb (271 kg) of raw ash per hour with favorable results. PRELIMINARY STUDIES Prior to committing laboratory research and development effort as well as support and coordination activities to this program, it was necessary to determine (1) the level of need for a freshly launched CCB reutilization program in this state and (2) what degree of versatility was necessary for such a process. State agency records and a survey of recent boiler operations indicated that in the state of North Carolina at least 77 facilities manage CCBs from their boiler operations. Despite continuing development efforts in more eastern parts of the state, the use of CCBs for commercial applications has not increased to a level which alleviates the need to store vast quantities in private monofills on the generator?s property. More than 1.25 million tons (1.13 million t) of CCBs are landfilled in NC annually, with 300,000 tons (271,985 t) per year generated in western NC alone. Many different boiler types, which span both very old units and those that are modern and efficient, were to be found. These included stoker-fired units, pulverized coal boilers, slag-tap furnaces, and fluidized bed combustion boilers covering a range of sizes. Any systems designed to separate CCB components from all these sources and convert them to useful secondary products would need broad processing latitude and flexibility. Up to the present there has been a paucity of research done in the western part of the state to find productive alternatives to storage in landfills. With tipping fees in our largest landfill now approaching $40 per ton ($44 per t) and escalating transportation fees (about $200 per truckload up to 40 tons, traveling a distance of 25 miles), the problem has become urgent both economically and ecologically. A well-designed, integrated wet process for CCB separation into value-added products had much potential to be less expensive than landfilling as well as to provide saleable materials with acceptable profit margins. These preliminary investigations also revealed that other major waste streams, in particular paper mill sludge and municipal and animal waste biosolids were important candidates for priority attention. Since these biosolids could furnish the organic component of a synthetic LWA product, they could be consumed as part of the same program. This added interest value to a growing list of partners to support and participate in the program.

Jan 1, 2009

By Xinghai Lei, Nan Wang, Xiangyang Jin, Yuqi Ren, Yang Li

The upward mining method, as an effective mining method, is widely employed in close-multiple coal seams to extend the service life of coal mines and improve the recovery rate of residual coal resources. However, the upward mining feasibility of the upper coal seam is related to the height of caved zone of interlayer strata after lower coal seam extraction. Therefore, it is extremely important to determine the height of the caved zone after the lower coal seam. The No. 9 coal seam (upper coal seam) and the No. 12- 1 coal seam (lower coal seam) in the Qianjiaying coal mine are selected as the research object. The characteristics of the interlayer strata structure field, fracture field, and subsidence field are studied using UDEC numerical modeling, in which the height of the caved zone is gotten after the No. 12- 1 coal seam extraction. Furthermore, the height of the caved zone is verified by onsite detection of GPR and BTVI. In the numerical modeling, the height of the caved zone is 19.6 m. And the height of caved zone is 14.7 m and 15.4–21.2 m, respectively, by using the onsite detection of GPR and BTVI. The heights of the caved zone onsite detection results are consistent with the numerical modeling result. The No. 9 coal seam is always located above the caved zone after the No. 12- 1 coal seam extraction. Consequently, the upward mining of the No. 9 coal seam is feasible.

Jun 28, 2023

By S. C. Sun

Pennsylvania has ample reserves of high-alumina clays which are potential sources of alumina, but many of these clays contain large amounts of iron, which makes them unsuitable for treatment by acid processes(1). The purpose of this investigation was to determine the optimum conditions for the selective hydrochloric acid leaching of iron (2-4) prior to the sulfuric acid extraction of alumina from Pennsylvania ferruginous high-alumina clays. This was accomplished by first testing the iron-bearing minerals and the clay minerals most often encountered in Pennsylvania clays to determine their rate of dissolution in hydrochloric acid solutions. The results of individual minerals were then based for leaching Pennsylvania clays with a 19% hydrochloric acid solution at the boiling point of the acid for approximately 30 minutes to achieve as high as 90% iron removal and only 2-5% alumina losses.

Jan 1, 1968

By K. Zeidler, T. Schwind

The Fort Canning Tunnel, Singapore, is an approximately 50 feet (15m) wide vehicular tunnel under shallow ground cover that has been constructed according to the principles of the NATM. Its shallow location in soft ground combined with a high groundwater elevation in close vicinity of historically important features called for special design considerations combined with a rigorous monitoring scheme. Surface, sub-surface and in-tunnel instrumentation was installed to monitor the performance of the ground and tunnel support during construction. Comparison of actual reading data with the results from the computer modeling carried out during the design phase is provided in this paper.

Jan 1, 2007

By L. E. Beverage

In 2006, the Mine Improvement and New Emergency Response Act (?2006 MINER Act?), Pub. L. No. 109-236, 120 Stat. 493 (2006) was enacted in a bi-partisan move to strengthen the 1977 Mine Safety and Health Act. This action followed several underground coal mining accidents at the Sago and Aracoma Mines in West Virginia and the Darby Mine in Kentucky. The focus of that legislation was, in part, to force technological development and implementation. It involved the recomposition and training of rescue teams. Requirements for sealing worked out areas of mines were changed when MSHA invoked its Emergency Temporary Standard (?ETS?) authority for the first time in many years. Increased penalty amounts were established for certain types of violations for all types of mining, and minimums were set for unwarrantable failure violations issued under Section 104 (d)(1) and (d)(2); 30 U.S.C. Section 814 (d)(1),(2). The entire 30 C.F.R. Part 100 penalty criteria was revamped in a rulemaking, effective in April 2007. The visions were ambitious and noteworthy and those in industry and government have spent the last four years working through the aftermath of intended and unintended consequences of these changes. The penalty structure arrived at in 2007 has proven unwieldy and has contributed to the increase in contested caseload now before the Federal Mine Safety and Health Review Commission. In essence, litigation under the Mine Act ground to a virtual halt when the number of cases increased but the budget for Administrative Law Judges, who hear the cases, and the Solicitor?s office who represents MSHA, was not increased. Addressing the backlog effectively was one of the major challenges when Joe Main was confirmed as Assistant Secretary in early 2010.

Jan 1, 2011

By L. S. Hansen

Organized efforts toward the prevention of injuries and occupational diseases have been of comparatively recent origin in the mining industry, dating generally from the beginning of this century. Mining-and particularly underground mining- is more hazardous in many respects than most other major industries, and continual and increasing attention has been given to its health and safety aspects. The importance of the physical well-being of those engaged in mining was recognized by Agricola, who, after describing the hazards encountered in 16th century mining operations, stated that "Some of these evils, as well as certain other things, are the reason why pits are occasionally abandoned." In the past 50 yr particularly, mine managements and labor organizations, separately or collectively, have mounted productive efforts toward the prevention of accidents and industry-associated diseases and illnesses. A statistical study of this period indicates that increasing awareness coupled with the endeavors of all concerned agencies has resulted in decreasing frequency of occurrences of injuries and illnesses. In recent years particularly the mining industry has used the services of safety engineers, industrial hygienists, inspectors, ventilation engineers and other specializing in locating and correcting deficiencies affecting the welfare of employees. Concurrently, the labor movement has incorporated into its organization individuals working in the fields of health and safety, many devoting full time to these responsibilities. Others serve in behalf of their fellow workmen as on-the-job safety representatives. Most authorities agree that accidents are caused by (1) unsafe acts, (2) unsafe conditions and, exceptionally, (3) Acts of God. The "unsafe act" often is cited as the prime cause. but many accidents, and attendant injuries, are the result of a blend of "unsafe acts" and "unsafe conditions," with each chargeable in varying proportions. It therefore is necessary to consider both the physical elements of the mine plant and the training, mental attributes and actions of all personnel involved. Analysis of an accident, if based on hasty reconnaissance and unduly hurried questioning, seldom will disclose more than surface causes and consequently will result in inadequate measures to prevent repetition. Mining involves unavoidable and calculated risks, as in all facets of life. It is most important then that men employed in mining be schooled in the hazards and develop fully the ability to evaluate and minimize risks. The environment, of underground mining often is harsh and strange compared to the more natural surface conditions man has learned to cope with as a part of established life patterns. The miner. therefore, must adapt to unusual situations and conditions and must develop a mental attitude permitting acceptance of change. 3.1-INDUSTRY-AFFILIATED SAFETY AGENCIES L. S. HANSEN There are many organizations primarily interested in health and safety. In addition to industry and labor groups, there are many private and governmental

Jan 1, 1973

By William M. Gleason

Hard times continued to plague the industry when the calendar rolled over to 2000. During 1999, the United States economy had grown vigorously, capping the longest economic expansion in United States history. However, the mining industry was not so fortunate. Commodity prices remained in a slump in the “new-economy” that was fueled by excitement and speculation about the power of the Internet during the infancy of the Information Age. Much of the investment money that once went to mining and exploration was now headed to the world of virtual gold mines. SME President Donald E. Ranta implemented new technology into his plans for SME. His two major goals were new membership growth and to foster the establishment of the comprehensive Internet presence for the Society’s technical information. His strategic priorities included enhancing the quality and quantity of publications, programs, meetings and short courses. “The Internet is the vehicle that will advance the priorities,” he said.

Jan 1, 2007

By Dan Witkowsky

Beginning on June 11, 2007, as many as 36, kindergarten-to-grade-12 (K-12) teachers will participate in a program designed to educate them all about the mining industry. The 39th Annual A Total Concept of the Mining Industry – All About Mining, will be conducted by the Colorado Mining Association Education Foundation, Inc. (CMAEF) and the Office of Special Programs and Continuing Education (SPACE) at the Colorado School of Mines. This flagship program includes four intensive weeks at the Colorado School of Mines. During that time, more than 75 volunteer lecturers will “educate the educators” about mining and its importance to the United States and the world. During the learning process associated with obtaining a basic understanding of mining and all its aspects, the teachers will be hosted by hundreds of other industry professionals at 10 Colorado mining operations. Also visited will be a government earthquake center, a museum of mining and industry, an earth mechanics laboratory, a metallurgical research center, a metallurgical concentrator, an electric power plant and a steel mill. Questions before, during and after visits will be answered by another select group of volunteers who will travel with the teachers to the various sites.

Jan 1, 2007

By S. Hamilton

Borates are essential to life, and to many products that are essential to an acceptable standard of living. They occur naturally in seawater at an average concentration of five milligrams of boron per liter. Fresh water lakes, rivers, streams and ground water generally have concentrations of about one milligram boron per liter. Borates are also present in soil at concentrations ranging from 0.1 to three milligrams of boron per kilogram. Because most of that boron is locked into insoluble minerals, clay or organic matter, boron deficiency is more widespread than boron enrichment. Borates evaporate into the atmosphere from seawater, rain, snow and hot springs. In rain and snow, natural boron concentrations range from 0.002 and 0.1 milligrams boron per liter. All told, boron moves through the atmosphere at a rate of 5 Mt to 7 Mt/a (5.5 million to 7.7 million stpy).

Jan 1, 2005

By S. M. Carpenter

In response to the FY2008 Consolidated Appropriations Act (H.R. 2764; Public Law 110?161), the United States Environmental Protection Agency (USEPA) issued the final Mandatory Reporting of Greenhouse Gases Rule (MRR). The rule, signed by the USEPA Administrator, Lisa Jackson, on September 22, 2009, requires reporting of greenhouse gas (GHG) emissions from large sources and suppliers in the United States, and is intended to collect accurate and timely emissions data to inform future policy decisions. The MRR will go into effect on January 1, 2010, and a report of the total emissions for calendar year 2010 will be due to the USEPA by March 31, 2011. Under the final MRR, suppliers of fossil fuels or industrial greenhouse gases, manufacturers of vehicles and engines, and certain facilities that emit 25,000 metric tons or more per year of GHG emissions are required to submit annual reports to the USEPA. The gases covered by the rule are carbon dioxide (CO2), methane (CH4), nitrous oxide (N2O), hydrofluorocarbons (HFC), perfluorocarbons (PFC), sulfur hexafluoride (SF6), and other fluorinated gases as outlined in Table A-1 of Subpart A of the MRR, which is also provided in Appendix A of this report.

Jan 1, 2011

By Charles W. Daugherty, James P. Gould, Kenneth R. Ware

INTRODUCTION As illustrated in Figure 1, the Washington Metropolitan Area Transit Authority's (WMATA) rapid transit system (METRO) ultimately will comprise 100 miles of line divided among 10 routes. At this time about 46 per cent of the system is under construction or in operation. Planning and design of an additional 38 per cent is at an advanced stage. Of the 84 miles under development or construction, about 10.4 miles consist of soft ground tunnels, and another 1600 feet of mixed face. This paper describes most of the factors considered by designers in setting grades for such tunnels. It is hoped the paper will be a useful guide to planners and engineers in developing similar transit systems. The problems faced in Washington, including those related to geology, are not so unique that the solutions cannot be applied to other systems. The paper also may be of interest to contractors who have not perceived the logic behind the selection of a particular vertical alignment. An attempt is made to explain the background constraints that make most tunnel alignments a compromise among competing alternatives. Readers might assume that the choice of alignments is largely controlled by geological conditions. In fact this is merely one of many factors to be considered.

Jan 1, 1976

By C. R. Copeland

Combustion processes, comminution and materials handling can generate airborne particulates. Regulation of these particulates by the U.S. Environmental Protection Agency (U.S. EPA) is becoming progressively more stringent, and regulations will soon include ?nanoparticulates,? which are particles finer than 100 nanometers (0.1 mm). Nanoparticulates are believed to have significant negative health effects due to their high surface area and reactivity. Although it was argued that nanoparticulate concerns were only important for combustion, studies at Michigan Technological University have shown that materials handling and comminution release significant quantities of nanoparticles into the air. Laboratory studies have shown that the use of sodium metasilicate reduced airborne particles finer than 10 mm (PM10) by 86% and particles finer than 2.5 mm (PM2.5) by 80% for iron ore. Additional studies were conducted that revealed that nanoparticulate emissions were present in the types of operations conducted at pyrometallurgical facilities.

Jan 1, 2008

By C. A. Young, R. G. Robins, E. J. Dahlgren

The formation of copper thio-complexes in sulfide solutions has been recognized for many years and the measured solubilities of certain copper sulfide minerals attributed to these complexes. Attempts to model this system have proposed either copper(I) or copper(II) thio-complexes, and these have been incorporated into computer programs for generating stability diagrams for the copper-sulfur-water system in order to delineate the region where the reductive dissolution of copper sulfide minerals is likely. In this paper it is proposed that the dissolution of copper from both ore bodies and sulfide tailings can be explained by the formation of the cupro-thio-complexes under anaerobic conditions. Stability diagrams are presented to depict the region and extent of the solubility.

Jan 1, 2001

Editor’s note: As usual, the June issue features an industrial minerals review. And some thanks are in order. Thank you to the industrial minerals annual-review editor, to the technical committees chair and vice chairs and to the authors of the individual commodity profiles. Jim Norman of GeoTrans Inc. is the industrial minerals annual-review editor. William Langer, U.S. Geological Survey, is the chair of the SME industrial minerals technical committees and the vice chair of the technical committee for construction materials. Other technical committee vice chairs include: •Lucy McCartan, U.S. Geological Survey, agricultural minerals. •Steve Herron, Oglebay Norton Performance Minerals, ceramics and refractory materials. •Srinivas Veeramasuneni, U.S. Gypsum, chemical raw materials. •Ismail Yildirim, Imerys, fillers and pigments. •Charles Landis, BPM Minerals, sorbents, filters and process aids. •Ray Harris, Wyoming Geological Survey, specialty minerals. Their help makes possible this June industrial minerals issue. On behalf of the readers, the editors thank them

Jan 1, 2004