Search Documents

By B. Tiryaki

Performance prediction models for partial face mechanical excavators, when developed in laboratory conditions, depend on relating the results of a set of rock property tests and indices to specific cutting energy (SE) for various rock types. There exist some studies in the literature aiming to correlate the geotechnical properties of intact rocks with the SE, especially for massive and widely jointed rock environments. However, those including direct and/or indirect measures of rock fracture parameters such as rock brittleness and fracture toughness, along with the other rock parameters expressing different aspects of rock behavior under drag tools (picks), are rather limited. With this study, it was aimed to investigate the relationships between the indirect measures of rock brittleness and fracture toughness and the SE depending on the results of a new and two previous linear rock cutting programmes. Relationships between the SE, rock strength parameters, and the rock index tests have also been investigated in this study. Sandstone samples taken from the different fields around Ankara, Turkey were used in the new testing programme. Detailed mineralogical analyses, petrographic studies, and rock mechanics and rock cutting tests were performed on these selected sandstone specimens. The assessment of rock cuttability was based on the SE. Three different brittleness indices (B1, B2, andB4) were calculated for sandstones samples, whereas a toughness index (Ti), being developed by Atkinson et al.1, was employed to represent the indirect rock fracture toughness. The relationships between the SE and the large amounts of new data obtained from the mineralogical analyses, petrographic studies, rock mechanics, and linear rock cutting tests were evaluated by using bivariate correlation and curve fitting techniques, variance analysis, and Student?s t-test. Rock cutting and rock property testing data that came from well-known studies of McFeat-Smith and Fowell2andRoxborough and Philips3have also been employed in statistical analyses together with the new data. Laboratory tests and subsequent analyses revealed that there were close correlations between the SE and B4 whereas no statistically significant correlation has been found between the SE and Ti. Uniaxial compressive and Brazilian tensile strengths and Shore scleroscope hardness of sandstones also exhibited strong relationships with the SE. NCB cone indenter test had the greatest influence on the SE among the other engineering properties of rocks, confirming the previous studies in rock cutting and mechanical excavation. Therefore, it was recommended to employ easy-to-use index tests of NCB cone indenter and Shore scleroscope in the estimation of laboratory SE of sandstones ranging from very low to high strengths in the absence of a rock cutting rig to measure it until the easy-to-use universal measures of the rock brittleness and especially the rock fracture toughness, being an intrinsic rock property, are developed.

Jan 1, 2006

By M. K. Elmouttie, G. V. Poropat

Mapping of exposed rock walls provides data on geological features such as joints, bedding planes, faults etc critical to the economics and the safety of mine operations. Traditional, manual methods of mapping can be time consuming, error prone and limited in their coverage. New methods have been developed to map exposed faces remotely and safely however the benefits of these methods are only fully realised when exposed structures can be quickly and easily mapped using automated methods. This paper describes the application of an automated method of analysis of 3D images that provides users with the capacity to map exposed structures automatically. The method is based on the use of vector classification methods used in some neural network systems and provides rapid and reliable identification of exposed planes. CSIRO Exploration and Mining is applying these methods to 3D images for a range of applications from pit mapping to machine automation.

Jan 1, 2006

By P. J. Petit

Changing mining conditions, legislative issues, rising costs, and the constrained supply of skills and electricity in South Africa, have been some of the criteria forcing mine operators and engineers to review the traditional use of compressed air to power underground hand-held drilling operations in narrow-stope, hard-rock mines. In answering the question, 'What is the best way to power this mine?', they have resorted to trade-off studies with results of limited usefulness, because they are site-specific, and use only a few comparative parameters, based on a small data set. This paper aims to provide definitive, objective, and quantitative decision-making approaches to evaluating alternative energy-delivery systems for stoping in narrow-reef hard rock mines, based on primary and relevant criteria. These include quantifiable criteria such as capital expenditure, operating costs, resulting financial returns, energy and water usage, production performance, life-of-mine, etc. Other important criteria with qualitative aspects are integrated. These are safety, health, and environmental concerns, legislative requirements, business risk, technology change, etc. The paper begins with a review of decision-making processes available, and proposes the use of the analytical hierarchy process (AHP) method as a multiple-criteria decision-making tool and the decision tree based on milestone-driven uncertainties, to validate the selection of the energy delivery system. The results of a multiple-criteria questionnaire completed by a variety of industry experts and professionals, such as production and operation managers, consultants, suppliers, and techno-financial analysts, are discussed. The evaluation indicates the potential for hydropower to be the best solution for narrow-reef hard rock mines, based on current information, mine design layout and production.

Jan 1, 2013

By J. Martinovic

The large proportion of gangue minerals present in platinum bearing ores in South Africa provides challenges to the flotation and downstream processes. In order to take effective measures to reduce their recovery in flotation, an understanding of the mechanisms and factors influencing their behaviour is needed. Typical gangue minerals are pyroxene, feldspar, quartz, chromite and talc. Of these, talc is a naturally hydrophobic mineral and although it is present in relatively small quantities, it has a disproportionate effect as it has a strong froth stabilizing effect, increasing the recovery of other gangue minerals by entrainment. Talc recovery is effectively reduced with the addition of polymeric depressants. Although the other gangue minerals are assumed to be hydrophilic and their recovery by entrainment is expected to follow the water recovery, there is some evidence that they may be activated by the typical reagent suites used. Reagents such as copper sulphate, added as an activator, and collectors are used to selectively induce hydrophobicity on the sulphides. It has been shown that some of these gangue minerals can be activated. This research work investigates whether inadvertent copper activation is mineral specific and evaluates the mechanisms and factors affecting the reversal of activation with the addition of the depressants using electrokinetic measurements, adsorption and microflotation tests. Results are presented that show that the selected minerals do respond differently and that the reversal of activation is dependent on mineral type, depressant type, dosage and ionic strength of the electrolyte.

Jan 1, 2005

By Peter Voulgaris, Allan Haines, Diane Walker, Ian de Bruyn

The Oyu Tolgoi porphyry gold and copper project is located in the south Gobi region of Mongolia. The Ivanhoe Mines project has the potential to become a long-life copper and gold producer that could rank among the largest in the world. There are five deposits which cover a strike length in excess of 6.5 km, from south to north they are named South Oyu, Southwest Oyu, Central Oyu, Hugo South and Hugo North. The first three, collectively known as the Southern Oyu deposits, are planned to be mined by open pits, whilst extraction of the deeper Hugo deposits is planned using block caving techniques. The pits will have diameters of approximately 1000m and a maximum depth of 550m. The geological environment consists of a sequence of porphyritic augite basalt, dacitic tuffs and sedimentary rocks that have been intruded by several generations of porphyritic quartz monzodiorite and numerous post mineralization dykes. Several major faults cut through the southern deposits juxtaposing the relative position of the stratigraphy. The geotechnical investigation for the Oyu Tolgoi Open Pits was conducted in three distinct phases of increasing complexity: scoping study; advanced scoping study and feasibility study. Each phase consisted of data collection, interpretation and analysis designed to progressively develop 3D geotechnical domaining for the empirical, structural and numerical evaluations. The development of the geotechnical design parameters for these green fields open pits posed many technical challenges, brought about by the conditions associated with a lithologically and structurally complex environment. The design work focused on the optimization of the pit geometry to conform to equipment selection and blasting characteristics. Limiting bench stack heights were derived from the influence of major structures. The overall slope angles in each pit sector were developed around the requirement for haulage ramps and geotechnical berms. This paper describes each of these aspects and the methodology used to address the integration of the geotechnical characteristics with the mining environment.

Jan 1, 2006

By L. A. Jordan, D. van Vuuren

A two-dimensional finite difference model has been developed to describe the reduction of kilogram quantities of dehydrated phosphogypsum. The model’s scope has been limited to focus on the heat transfer and reactions that occur within a mass of material contained in a vessel inside a furnace rather than also including the effects of heat transfer to the vessel. Changes in the heat transfer properties (k, ρ, and Cp) are incorporated as the composition of the mass changes as the chemical reactions progress. The model is validated against experimental data, with samples heated to 1000°C at 3°C min−1 while purging with nitrogen gas. A sensitivity analysis of model predictions to the pre-exponential factor of the reaction rate constant of the main chemical reaction and the thermal conductivity of the powder bed indicated that, at the envisaged process conditions, the behaviour of the system depends much more on the rate of heat transfer than on the rate of the chemical reaction. The model demonstrated a significant increase in accuracy when the thermal conductivity was modelled to increase linearly with temperature compared to assuming a constant value.

Oct 1, 2022

By P. den Hoed, J. Nell

Tests were conducted on samples of rutile, titaniferous slag and ilmenite; each sample was mixed with coke and chlorinated in a bubbling fluidized bed at 1000°C. Profiles of the rates of chlorination of species were constructed from chemical compositions of the bed residues at different durations. From the start FeO and MnO are chlorinated quickly and all but entirely in a fraction of the time it takes to chlorinate all the TiO2. When the level of FeO is significant, as in slag and ilmenite, FeO is chlorinated faster than TiO2is. In these oxides, there is an inverse relationship between the rates of chlorination of FeO and TiO2during this first stage; the relationship, moreover, correlates linearly with the initial percentage of FeO in the oxide. We identify three stages in the chlorination process; a first, in slag and ilmenite, when FeO is being chlorinated; a second, when TiO2is most readily chlorinated; and a third, towards the end, when the levels of TiO2are reduced to those of other species. The rates at which individual species are chlorinated are analysed in terms of their appreciation or depreciation with respect toTiO2

Jan 1, 2003

By L. Bbosa

Paper written on project work carried out in partial fulfilment of BSc (Hons) (Eng) (Mechanical) degree Discrete element methods (DEM) are being used to provide detailed impact histories of the particles in comminution devices, such as mills. To match this immense detail of information, far more informative breakage tests than those that are generally conducted are now required. The split Hopkinson pressure bar apparatus is used in this study, as it allows the calculation of breakage forces and absorbed energies. The geometry of rock particles has been identified as significant, so this project undertook to identify the influence of shape on the breakage pattern of blue stone. Comparisons are then made between the breakage pattern of angular rocks and rounded, milled rocks for single impact fracture and consecutive impact loading at low energy. Results of this experiment indicate that although breakage for both geometries occurs over a similar energy range, rounded particles have the greater probability of fracture because they absorb more of the impact energy for a given loading. Size distributions of progeny show that five pebbles or more are sufficient to predict the distribution of most particles in small energy regimes. Cumulative impact testing shows that considerably more energy is required to break a rock through cumulative damage than through a single impact?this is of considerable importance in the light of the indications from DEM simulations that most breakage in a mill will be from cumulative damage rather than single impact breakage.

Jan 1, 2006

By L. P. Lamprecht

Traditionally, South African shaft sinking operations have used electric detonators for the initiation of blastholes. Globally, the trend in shaft sinking is to use the shock tube and detonating cord (STDC) initiation system, with value adding benefits. In pursuing this global trend, Cementation Mining of South Africa in partnership with SMX have ventured the STDC route. This paper explores the work carried out to date, and identifies a number of benefits to be gained by using the system.

Jan 1, 1999

By A. Haines, O. Varaud, I. Baidoo

Abosso Goldfields Limited (AGL) is in the process of developing an expansion of their Damang Open Pit gold mine in Ghana. AGL acquired the Damang mine in January 2002, with SRK participating in the geotechnical investigation and design for the project since 2001. A deep resource drilling program, completed during 2004, intersected an extension of the orebody below the then planned final pit floor. A feasibility study has been completed to determine the economic extraction of this deep ore with an expanded pit shell. The Damang mine is in a stockwork sulphide deposit at the culmination of the Damang anticline. The deposit occurs as hydrothermal mineralisation associated with dominantly east dipping thrusts and sub-horizontal quartz veins. Primary gold mineralisation also occurs in the conglomerates of the Tarkwaian Formation. The geological units consist of steep easterly dipping dolerite, sandstone, siltstone and phyllite beds, with the weathering profile comprising saprolites overlying a relatively thin joint oxidized horizon. It is planned to deepen the current open pit to a final depth of up to 270 m, primarily by the development of a push-back of the eastern and western walls. The edge of the Eastern Tailings Storage Facility (ETSF) is currently located within 80 to 100 m of the crest of the existing pit. The geotechnical design focused on the optimization of the bench face angle and finally recommended a ?Steep Slope Strategy?, involving 24m high near vertical benches. Limiting bench stack heights of 96m at a maximum of 66° were derived from the influence of major structures and the variation in rock mass conditions. The overall slope angles in each pit sector were developed around the requirement for haulage ramps. One of the main design challenges was to optimise the standoff distance between the final pit crest and the ETSF. This process had to consider maximum access to the resource without undue influence on or from the nearby tailings dam. A planned increase to the height of the dam wall was an additional factor in the design. Dewatering of the pit walls was also a major consideration in this tropical environment.

Jan 1, 2006

By J. Alexis, G. Ye, E. Burström

Over the past twenty years the 3 MW DC arc furnace at MEFOS has been frequently used for development of new processes. These processes include recovery of valuable metals from slag, sludge and dust from steel and other metallurgical industry, treatment of ashes from power plant and incinerators, smelting reduction of minerals and zinc recovery from EAF dust. The process characteristics of the DC arc furnace operation in terms of: ? selective reduction, ? total reduction, ? process stability and flexibility, ? dust carry-over, ? thermodynamic conditions provided in the hot spot area, ? precision in composing slag products These are analysed and described in this paper based on technical results from selected test campaigns over the years and thermodynamic considerations. The electromagnetic properties of DC arcs beneath the electrode have been studied by CFD simulation. The calculated result enables us to understand some interesting technical phenomena observed. The heat balance has also been considered based on data obtained from test campaigns and heat balance calculation.

Jan 1, 2004

By A. J. C. Paterson

High density slurry and paste tailings systems offer significant environmental benefits primarily related to reduced water consumption. However, these potential advantages need to be evaluated on a project-by-project basis. The successful design of a thickened or paste tailings system requires that the system is designed to accommodate the effect of the high density slurry on pumps, pipelines and the overall system operation. The transport system must be designed as an integrated unit and the interaction of all the components need to be considered. The transport system includes the slurry preparation plant, the pump station and the pipeline. This paper assesses the impact of increasing the slurry density in a platinum tailings system from conventional densities to thickened and paste tailings densities. As slurry density and rheology increase, there is a sharp increase in energy consumption for the additional water savings and this additional cost needs to be considered. A case study shows that there is a considerable benefit in increasing densities to the point at which tailings can be still be deposited in the standard manner. For existing systems, increasing density can result in an increased capacity at a marginal power cost, provided that the slurry is not too viscous. For a new system, a smaller pump and pipeline can result in lower capital costs and a marginally higher energy cost, if the optimum density is selected. Keywords: tailings, paste, pumping, slurry

Jan 1, 2004

By R. Scott

This article describes and evaluates the establishment of Kuyasa Mining including the search for a suitable deposit, the ongoing lack of finance, and market constraints. Despite the dramatic initial growth and success of their Ikhwezi Colliery near Delmas, Mpumalanga, Kuyasa?s experiences offer some sobering arguments for significant changes to mineral rights ownership, the attitude of financial institutions and government policy if South Africa is to have a dynamic and successful junior and small-scale mining sector.

Jan 1, 1998

Despite the wealth of information available on phase equilibria of oxide systems there remainmany gaps and inconsistencies in our knowledge base. From an industry perspective there is anongoing need to adequately describe the phase chemistry of slag systems in order to optimizeprocess performance and improve productivity. Since this chemical behaviour cannot be predictedfrom first principles it follows there is also an ongoing need for accurate experimental data. The advances made in recent years in the capabilities of sophisticated analytical and measurement equipment have made it possible to develop new experimental techniques for the direct determination of phase equilibria in low order and complex multi-component slag systems. In addition the development of powerful computer modelling tools makes it possible to provide more comprehensive descriptions of the phase chemistry, to present the information in a range of perspectives, and to critically analyse the various types of related thermodynamic and structural information available. This review provides an overview of the types of information that can be used to determine phase equilibria in slags systems, analyses the influence of uncertainty and the relative importance of these types of data, and describes the advantages and limitations of the various experimental techniques that can be employed to obtain this information. Examples of recent studies are provided that demonstrate how an integrated approach to the determination of phase equilibria in complex systems, involving the use of targeted experimental studies and systematic thermodynamic model development, can lead to a better utilization of our current research capabilities and resources and more accurate descriptions of these systems. Keywords: slags, phase equilibria, experimental techniques

Jan 1, 2004

By S. J. Oosthuizen

This article explores the Fray Farthing Chen (FFC) Cambridge process, a novel method for the electrochemical deoxidation of metal oxides in molten salt, discovered at the University of Cambridge in 1997. The process was hailed as a highly promising, potentially low cost, novel method for the production of titanium metal direct from its oxides. The article should inform researchers in the field of some of the challenges in the commercialization of a novel, high profile process involving multiple stakeholders. The author, former senior process engineer at British Titanium Plc, the company originally tasked with commercializing titanium production via the FFC Cambridge process, reviews the latest literature and discusses past and present progress in the pursuit of low cost titanium metal via this process. Topics explored include the history of the process, attempts at commercialization, NASA?s alternative application, and present status of the process. Keywords FFC Cambridge, titanium, molten salt.

Jan 1, 2011

By Mark Coleman

Pnuematic Conveying and Process Injection Technologies have been implimented in the metals markets for the last 40 years and have consideribly improved the productivity and the performance of many processes. There have been many steps forward in handling technology and this paper seeks to consider those now offered by Clyde Materials Handling who as an established customer-driven solutions provider, which has turned its attention to supporting the Metals Market. Clyde seek to utilises its knowledge, expertise and technologies to transform the production processes of its customers, who operate in the ferrous and non-ferrous metals industries. With over 30 years experience in the process improvement industry, Clyde Materials Handling has helped their global customer base transform the way in which they operate their processes, which has enabled them to generate sustainable economic benefit and maintain their positions as leaders in their respective markets. Operators within the metals market have developed and deployed pneumatic conveying and pneumatic injection technologies. These environmentally supportive and sustain-able solutions have been used to transport raw materials within operating facilities, from storage to silo, as well as injecting these materials directly into the heart of production processes. Operators, such as Codelco in Chile, Corus Steel in the UK, and many others across the World have seen pneumatic injection solutions transform their process and costs. To inject a consistent, pulseless and accurate flow of material to a copper concentrate bath smelter, or injecting granular or pulverized coal as a coke substitute in to a blast furnace via the Tuyeres helps to increase the operational capacity, availability and productivity and reduce the cost of the operation. This paper will discuss and highlight the ways in which pneumatic conveying and injection technologies, created by Clyde Materials Handling, and applied in partnership with the customer, have helped to improve the operational performance of the production processes of operators across the non-ferrous metals markets with specific reference to applications in the Lead and Zinc Industries. With examples from Zinc Fuming in Australia, Zinc Calcine and Powder Handling in Korea, Precision coal injection to QSL and TSL Furnaces, and metered distribution of Zinc Calcine to Reactors.

Jan 1, 2008

By R. J. Forzatti

The production of sulphuric acid from sulphur generates heat. The majority of this heat is recovered as steam and is often used to generate electricity. Heat not recovered as steam is rejected to cooling water systems. The design of the turbine, condenser, and cooling water systems impacts the overall water, energy, and environmental footprint of the plant. This review considers a conceptual 2000 t/d sulphuric acid plant with several alternative cooling water systems. The review utilizes Hatch?s 4 Quadrant sustainable design tool to compare the alternatives on both an economic and a weighted sustainability scale.

Jan 1, 2014

By J. M. Lottering

Paper written on project work carried out in partial fulfilment of B Eng (Chem) degree Operational factors influencing the electrostatic separation of mineral sands were investigated in a laboratory separator. Measurements were collected online by means of an optical sensor using diffused reflectance spectroscopy to determine the mineralogical composition. The results have shown that the roll speed and potential were the dominant operating variables, collectively explaining more than 83% and 68% of the product grade and yield, respectively. In contrast, the feed rate, temperature and position of the plate did not affect separation. The effect of the ambient relative humidity, ranging from 10% to 45%, could not be assessed conclusively and at best appeared to have a weakly beneficial effect on the product grade. Keywords: process modelling, high tension roll separator, mineral sands

Jan 1, 2006

By C. Ntsele

Stirred milling technologies have firmly established themselves in concentrator circuits as energy-efficient alternatives to tumbling ball mills. High and continued increases in electricity costs, coupled with the ever-increasing power consumption by primary grinding circuits due to declining head grades of ore-bodies, provides a compelling case for these technologies. Additionally, the ability to successfully deploy stirred milling in coarse grinding applications extends the range of use in concentrators, thus increasing the opportunity matrix for energy optimization in a flowsheet. This paper therefore details methodologies and strategies that can be applied to evaluate the optimum stirred milling solution for different concentrator applications. These methods and strategies will focus specifically on the two major stirred mill machine types; namely, gravity-induced (VERTIMILL? grinding mill and Nippion-Eirich tower mill) and fluidized (SMD, Isamill?, Knelson-Deswik mill, etc. ). Finally, case studies from circuits across industry and laboratory tests will be used to illustrate the energy benefit from the use of stirred mills.

Jan 1, 2012

By A. V. Wilke

The metallurgical balance is a tool usually applied in the mining industry. The final result is used for different objectives. All the existing software for the calculation of the metallurgical balance fits the numbers in such way that a logical correspondence between the input and output materials exist. Nevertheless, the accuracy of the metallurgical balance strongly depends on the quality of the input data. Division El Teniente of Codelco Chile has been optimizing the metallurgical balance system the last 14 years. As well, it has participated in the development of corporate norms to optimize the operations of sampling and weighting systems. As a consequence, the precision and the accuracy of the metallurgical balance have been improved in a significant way. Also the understanding of process variability was enhanced. The improvements have allowed Codelco to discover and minimize hidden losses and to better support top management decisions. The present paper describes the main aspect of the continuous improvement process.

Jan 1, 2009