Search Documents

By Chris Ringas

The safe operation of gas transmission pipelines is increasingly coming under the spotlight. Increasing environmental pressure is also forcing pipeline owners and operators to ensure the integrity of their pipelines. The integrity of a pipeline is usually determined using intelligent pigging, often referred to as In Line Inspection (ILI). However, in many cases, gas pipelines cannot be pigged for a variety of reasons. The National Association of Corrosion Engineers (NACE) has recently published Recommended Practice (RP) 0502, referred to as the External Corrosion Direct Assessment (ECDA) Methodology to assist pipeline owners with assessing the condition of pipelines that cannot be pigged. 2. External Corrosion Direct Assessment - NACE RP 0502 The ECDA Methodology is conducted in four phases as follows: ? Pre-Assessment ? Indirect Inspection ? Direct Examination ? Post-Assessment In the Pre-Assessment Phase, all the relevant historical and current data relating to the pipeline in question is reviewed. This covers pipeline, construction, soils/environmental, corrosion control and operational data. The aim of the Pre-Assessment Phase is to determine whether ECDA is feasible, and if so, to define the ECDA Regions and finally to select the Indirect Inspection Tools that will be used for each region. Typical overline techniques used for overline surveys include the following: Voltage gradient surveys ? DCVG or ACVG

Jan 1, 2006

By R. D. Hull

Paper written on project work carried out in partial fulfilment of B.Sc. (Eng.) (Mining) degree As a partial fulfilment for the degree of B.Sc. (Eng) (mining) at the University of the Witwatersrand, a dissertation was to be completed in the mining industry. This was done at Finsch mine, with the purpose of determining the best solution to the required secondary breaking problem. In order to complete the study of the secondary blasting method available for use in the new block 4, cave mining method at Finsch mine the following problem statement was identified and solved ?The methods currently in use, for the secondary breaking of oversize rocks at their source in the current production levels, are to be investigated, and their applicability to the new block 4mining project determined?. To effectively achieve this problem statement above; time was spent researching and investigating, in depth, the methods that are currently in use at both Finsch and Koffiefontein mines; so as to gain practical knowledge of these. The methods were identified and independently evaluated, taking into consideration factors such as costs of the equipment, time to break oversize rocks, advantages, disadvantages, safety and labour requirements, etc. This in turn then allowed for a direct comparison between the methods and the decision as to the best to apply to the new block 4 production level. The methods that were investigated included: ?Concussion blasting, where concussion bombs and lay-on charges are used to break hang-ups and boulders. ?Drill and blast methods, where holes are drilled in large rocks and charged manually with explosives. ?Emulsion secondary blasting, which is a new project in use at Koffiefontein mine from African Explosives Limited. ?The Ro-BustTM breaking system, a hydro-fracturing breaking system. Once all the methods had been evaluated and compared it was found that the Ro-BustTM Breaking system was the most applicable for the breaking of boulders, with, the Emulsion Blasting System being used for hang-ups. Further information and the more in-depth version of this report, is stored in the resource centre at De Beers?Finsch Mineand the School of Mining Engineering WITS University.`

Jan 1, 2002

By M. F. Handley

Sequential grid mining has been employed as the primary mining strategy at the AngloGold West Wits Elandsrand Mine since the inception of stoping operations from the sub-vertical shaft system in 1988. Little has been published on sequential grid mining as a mining strategy since, and the purpose of this paper is to describe sequential grid mining, its history, its implementation at Elandsrand, and the outcome to date. The results obtained using sequential grid mining have been evaluated from seismic data, productivity statistics, and rock related accident statistics. Comparisons with neighbouring mines namely Western Deep Levels and Deelkraal, have been made to substantiate the improved conditions observed at Elandsrand, and to compare sequential grid mining directly with longwall mining in similar conditions and at similar depths. Sequential grid mMining is shown to be cost-effective, more flexible, and safer than long wall mining in similar conditions, at least on the Ventersdorp Contact Reef in the western part of the Carletonville Goldfield. More work is necessary to establish it as the favoured mining strategy at depths exceeding 3000 metres, and for reefs other than the Ventersdorp Contact Reef.

Jan 1, 2000

By H. Kotzé

Ticor SA began with a detailed feasibility study in 1995. The Hillendale mine (situated between Richards Bay and Empangeni) and mineral separation plant were approved in 2000. The smelter, just outside Empangeni, consists of two 36 MW DC arc furnaces that were commissioned in 2003. Experiences gained during the initial commissioning of the furnaces proved valuable in later commissioning work, as shown by the increase in ramp-up rates. The capacity of the plant is 250 kt/a TiO2slag and 145 kt/a of pig iron.

Jan 1, 2006

By P J. Terbrugge, O K. H Steffen

Open pit slope design has conventionally been effected as a bottom up function utilising available geotechnical information. This results in a decision criterion based on Probability of Failure and Factor of Safety with a risk assessment being carried out on the proposed design slopes. The design approach recommended reverses the process using fault event tree decision methodology. The consequences of this approach are that acceptable risk criteria have to be determined by mine owners. Slopes are then designed by the technical staff to achieve these corporate goals. Benefits that arise from the process are that the owners take a proactive decision on the risk benefit relationship allowing the technical staff to optimise the geotechnical exploration programme and design.

Jan 1, 2006

By K. M. Li, Y. D. Zhang

The selection of stripping dragline is a complicated problem. Several factors, such as the deposit buried conditions, the demand of mine production rate, cast blasting result, the mining/stripping operation method and parameters, etc. may comprehensively influence the optimal selection of technical specifications of the dragline. Under these circumstances, the basic thinking and procedures for dragline selection are put forward as follows. •Step 1—Initially estimate the dragline annual stripping rate and stripping bench height according to the annual coal production rate and advancing speed of mining front. Then the feasible alternatives of dragline sizes can be calculated and selected from the existing dragline series. •Step 2—A computer simulation model is developed to simulate the dragline stripping operation, to obtain a series of working face parameters, then to select the best dragline alternative. This step can be interactively iterated until the satisfactory results are obtained. •Step 3— Sensitivity analysis can be done with the systems simulation model by changing the stripping bench parameters, e.g. stripping bench height and cut width, etc. to verify and modify the selection results if necessary. The mathematical model for dragline stripping simulation has been set up. The flowchart of the model is shown. A case study for a large surface coal mine with annual production rate of 16 Mt/a is followed. The dragline bucket capacity and operation radius, stripping bench height and cut width as well as other parameters are comprehensively optimized and selected. Keywords: Open cast, dragline, specification, selection, cast blasting

Jan 1, 2003

By W. Stumpf

Mill log analyses and complementary hot deformation studies were carried out on the as-cast structure and on a hot rolled structure of the same low carbon steel (SAE 1006) that had been processed according to the direct or hot charge route in a compact strip plant. The main softening mechanisms during hot rolling were found to be complete dynamic recrystallization during each pass above about 1000°C for the as-cast structure with an austenite grain size of 277µm and, secondly, incomplete static recrystallization after each pass with a finer austenite grain size of about 26 µm and tested below 1000°C. A two-stage hot working mechanism has also been found by others on a similar steel also processed by the hot charge route and this may appear to be a characteristic of this type of material. Constitutive constants determined from hot working studies were combined with other constants from the literature and incorporated into a grain size development model that correctly predicts the final ferrite grain size in the hot rolled strip steel. The predicted incomplete static recrystallization during the last three finishing passes in the plant appears to result in some retained strain in the hot rolled austenite as it transforms to ferrite on the run-out table. Analyses with the model predict relatively little sensitivity of the final ferrite grain size to process and product variables such as temperature and strain per pass for the last three passes and also the starting austenite grain size in the slab. Keywords: Low carbon steel, hot rolling of strip steel, rolling mill log analyses, austenite grain size, ferrite grain size, grain size modelling.

Jan 1, 2003

Often plant performance suffers as a result of poor control. Poor control leads to low mill throughputs, poor classification and less than satisfactory concentrate grades and overall recoveries. By using the appropriate control tools, substantial gains in plant performance can be made. Mintek?s MillStar and FloatStar controllers have been implemented at various sites across the world. The MillStar controller incorporates leading technology that controls process units from the mill feed through to the flotation feed. Typical results show that milling circuit throughput is increased by 6-10 % and the final product grind size is tightly controlled, thereby enhancing flotation performance. The FloatStar controller is aimed at stabilising and optimising flotation circuits. Through improved level control alone, recovery improvements of up to 1 % have been achieved. Furthermore, by using on-line grade analysers, the controller stabilises final concentrate grades, whilst maximising flotation recovery.

Jan 1, 2005

By E. Isokangas

A mine is essentially a series of operations, including drilling and blasting, crushing, milling, flotation, and leaching, that are interconnected and therefore interrelated, with the performance of one operation affecting the performance of another. Optimizing each stage separately without considering the whole system often causes potential economic benefits and energy savings to be missed. However, the PIO methodology is a thorough approach which considers these individual process activities within the context of the whole process. The basic principle is to optimize the process as a whole, rather than each process step in isolation from the others. Metso?s Process Technology and Innovation (PTI) group offers a global consulting service for the mining and construction industries. A significant amount of this consulting work involves process integration and optimization (PIO) studies. When conducting a PIO study, every aspect of the process is considered. In addition to drilling and blasting, transportation, handling and storage, crushing, screening, grinding, flotation, separation, and recovery, other aspects including equipment utilization and energy consumption and even greenhouse gas emissions are also included if necessary. In a PIO project, it is very important to understand what type of material is being processed at any point in time. That is, which domain or domains is the material part of? This is necessary in order to observe the effect of different ore sources (and the blending of sources) on concentrator performance. Linking the ore from the pit to the concentrator required the development of an ore tracking system. As a result, PTI developed a radio-frequency based material tracking system called SmartTag?. This system allows tracking of ore from its source through blasting, run-of-mine (ROM) pads, crushers, intermediate stockpiles, and finally into the concentrator. Using the SmartTag? system, definitive correlations can be made between the performance of the plant and the plant feed characteristics, including the domain from which the feed ore originated. Since its commercialization in 2007, SmartTag? has been used in the majority of PTI?s consulting projects and several permanent systems have been installed worldwide1. Successful applications of the SmartTag? system have encouraged development to allow the system to be used in a wider variety of plants, in particular plants with finer crushing and screening stages. This paper describes how the SmartTag? system is being utilized by PTI and the benefits being gained by its use in PIO projects, as well as presenting some case studies.

Jan 1, 2012

By M. Le Roux

Fine coal (-500 µm) is notoriously difficult to dewater. It is not uncommon for a dewatered product to have a moisture content as high as 30 per cent after vacuum filtration. This poses several handling and financial problems to such an extent that a lot of fine coal is discarded onto slurry waste ponds. A novel way of dewatering fine coal was developed at North-West University. It entails deliberately damaging the filter cake during dewatering to allow for an increased flow of air through the cake at the expense of the applied pressure differential. This method resulted in an average improvement in final cake moisture of between 3 per cent and 5 percent when executed in the laboratory under controlled conditions. A device was designed that could be fitted onto existing belt filters that would damage the filter cake as it passes by. This device was tested on a vacuum belt filter installation at a coal beneficiation operation in the Waterberg coal field in South Africa. The results showed a 3 per cent reduction in final moisture of the cake, proving the validity of the method at full industrial scale.

Jan 1, 2012

By D. Zhou, T. Hamano, Tsukihashi. F., W. -G. Seo

The thermodynamic properties for the CaO-CaF2and CaO-BaO systems were calculated by molecular dynamics (MD) simulation using Born-Mayer-Huggins type pair potential. The parameters of interatomic potential were obtained by fitting the thermodynamics properties of CaO, CaF2and BaO with the experimental data. The phase diagrams for the CaO-CaF2 and CaO-BaO systems were calculated by the thermodynamic properties obtained by MD simulation. The eutectic composition and temperature of the CaO-CaF2system calculated by MD simulation were about 28 mole per cent CaO and 1575K, respectively. The calculated eutectic point agrees very well with experimental data, which are about 22 mole per cent CaO and 1633K, respectively. Keywords: molecular dynamics simulation, thermodynamics, phase diagram, calcium oxide, calcium fluoride, barium oxide.

Jan 1, 2004

By C. Maree

Paper written on project work carried out in partial fulfilment of B. Eng (Chem. Eng.) This paper describes the development and use of a process simulator to optimize gypsum recovery at Afmine, a small plant near Yzerfontein on the South African West Coast. The simulator consisted of models of the major plant equipment, viz. hydrocyclones, surge bins, settling tanks, a primary sieve and a dewatering screen. Experimental data suggested that the equipment could be modelled satisfactorily from data published in the open literature. Simulation studies have indicated that gypsum losses on the plant could be reduced substantially by means of some relatively minor modifications to the plant layout. Moreover, sensitivity analyses of the plant have indicated that optimization of the settling tanks should receive priority over the other process units.

Jan 1, 2005

By M. Le Roux

Fine coal (-500 µm) is notoriously difficult to dewater. It is not uncommon for a dewatered product to have a moisture content as high as 30 per cent after vacuum filtration. This poses several handling and financial problems to such an extent that a lot of fine coal is discarded onto slurry waste ponds. A novel way of dewatering fine coal was developed at North-West University. It entails deliberately damaging the filter cake during dewatering to allow for an increased flow of air through the cake at the expense of the applied pressure differential. This method resulted in an average improvement in final cake moisture of between 3 per cent and 5 percent when executed in the laboratory under controlled conditions. A device was designed that could be fitted onto existing belt filters that would damage the filter cake as it passes by. This device was tested on a vacuum belt filter installation at a coal beneficiation operation in the Waterberg coal field in South Africa. The results showed a 3 per cent reduction in final moisture of the cake, proving the validity of the method at full industrial scale.

Jan 1, 2012

Viscosity measurements were carried out on slags in the CaO-Cu2O-CuO-MgO-SiO2systemcontaining ~ 63 wt% SiO2in air. The experimental work was carried out over a range of temperatures where the slags were completely liquid. Initial measurements were on a binary CaO-SiO2slag to which incremental additions of CuxO-MgO-SiO2slag with the same silica mole fraction were made. The viscosity-temperature relationship was measured for slags with‘Cu2O’contents of 0.02, 0.19, 0.38, 0.79, 1.69, 2.47, 3.01, 5.31 and 10.0 wt%. The proportions of Cu+and Cu2+in the slags were determined. The oxidation state of Cushifted from predominantly Cu+to Cu2+, with the Cu+/Cu2+ratio of approximately 0.3 for slag with a Cu content above 2 wt%. This is equivalent to Cu1.13O. The trends observed for changes of Cu2+/Cu+redox ratio with slag chemistry were consistent with the literature. Decreasing the CaO content by substituting copper oxide resulted in a decrease in the Cu+/Cu2+redox ratio. The change in ratio corresponded to a shift of the value of x in CuxO from an initial value of 1.8 to 1.1,when the slags contained 10% ‘Cu2O’. In this study, the SiO2content of the slags varied between 64 and 60 wt% as the Cu content increased. The viscosity of the slag containing 10 wt% CuxO was nearly 4.5 times lower than the binary CaO-SiO2slag. As the silica mole fraction (xSiO2) actually stayed constant (0.61±0.009),the results show that CuxO acted as a network breaker. Comparison with other ternary slags with similar silica mole fractions suggest that that addition of CuxO to silicate slags has a stronger effect on lowering the viscosity than FeO or MnO has on a molar basis. Keywords: viscosity, copper, silicate, slags

Jan 1, 2004

By Gaspard Devos

1. A NEW CONTEXT FOR METAL INDUSTRY Producers and owners of industrial extractive sites are living hard times due to Environmental pressure and liabilities. This is valid whatever the region in the world, it is just a question of time. On one hand, the normative environmental pressure is increasing through more severe regulations and controls on all pollution sources and production materials. [ ] Furthermore, more impurities are extracted and captured, more the volume of the related wastes is increasing. But disposal costs are increasing, disposal areas for wastes are restricted, markets for wastes are limited and technologies for waste treatment are, most of the time, not available. On the other hand, for most of the extractive industries, the costs required to get access to refine primary raw material are killing the profitability of the industry. Definitively, a technological and economical breakthrough is ongoing: extractive industries have to increase their feed from secondary material and to be involved more and more with the recycling business.

Jan 1, 2005

By A. Haque

The shear behaviour of infilled joints produced from ordinary gypsum plaster (gyprock) and bentonite was investigated in the laboratory under Constant Normal Stiffness (CNS) conditions. Shear tests were performed on saw-tooth profiles having Joint Roughness Coefficients (JRC) of 4.75 and 9.25 under an initial normal stress (sno) of 0.30 to 1.10 MPa, and at a normal stiffness (kn) of 8.5 kN/mm. Test data under the same sno and infill thickness to asperity height ratio (t/a) were analysed for two different sets of JRC. The peak shear stress plotted against the t/a ratio under constant sno revealed an increase in peak shear stress with the increase in JRC, up to a t/a ratio of about unity. The effect of roughness on the peak shear stress was observed to be minimal when the t/a ratio exceeded 1.40. A mathematical model for the prediction of peak shear stress due to the increased infill thickness has been developed based on a hyperbolic stress-strain relationship and energy balance principles. The model predictions are in good agreement with the laboratory observations. Le comportement de cisaillement des joints remplis produits à partir de plâtre ordinaire et de bentonite a été étudié dans le laboratoire sous des conditions de rigidité normales constantes. Des essais de cisaillement ont été réalisés sur des profils en dents de scie ayant des coefficients de rugosité des joints (CRJ) variant de 4,75 à 9,25 sous un effort normal initial (sno) de 0,30 à 1,10 MPa, et une rigidité normale (kn) de 8,5 kN/mm. Le résultat des essais conduits sous la même contrainte et épaisseur de remplissage au rapport aspérité/hauteur (t/a) ont été analysés pour deux ensembles différents de CRJ. La variation de l'effort de cisaillement maximal contre le rapport t/a sous une contrainte normale constante a indiqué une augmentation de l'effort de cisaillement maximal avec l'augmentation du CRJ, jusqu'à un rapport de t/a proche de l'unité. L'effet de la rugosité sur l'effort de cisaillement maximal a été minimal quand le rapport t/a a excédé 1,40. Un modèle mathématique pour la prévision de l'effort de cisaillement maximal dû à l'épaisseur accrue du remplissage des joints a été développé sur la base de la variation entre contraintes hyperboliques et déformation et sur des principes de bilan énergétique. Les prévisions du modèle sont en bon accord avec les observations de laboratoire. Das Scherverhalten in mit gewöhnlichem Gips und Bentonit gefüllten Klüften wurde im Labor unter Bedingungen konstanter Normalsteifheit (CNS) untersucht. Scherversuche wurden durchgefürt für Sägezahnprofile mit Werten des Fugenrauhigkeitskoeffizienten (JRC) von 4.75 und 9.25 unter Normalspannungs-werten (sno) von 0.30 bis 1.10 MPa, und bei Normalsteifheit (kn) von 8.5 kN/mm. Testresultate für gleiche Werte von sno und Verhältnis Fülldicke zu Rauhigkeit (t/a) wurden untersucht für zwei verschiedene Werte von JRC. Die Beziehung zwischen maximaler Schubspannung und und t/a Verhältnis unter konstantem sno zeigte einen Anstieg der maximalen Schubspannung mit zunehmendem JRC, bis zu einem t/a Verhältnis von etwa 1.0. Der Einfluss der Rauhigkeit auf den Maximalwert der Schubspannung war minimal solange das t/a Verhältnis den Wert von 1.40 überstieg. Ein mathematisches Modell wurde entwickelt für die Vorhersage der Schubspannung die von zusätzlicher Fülldicke erwartet werden kann, ausgehend von einer hyperbolischen Spannungs-Dehnung Beziehung und dem Energiegleichgewichts-prinzip. Die Modellvorhersagen zeigten gute Uebereinstimmung mit den Laborbeobachtungen.

Jan 1, 2003

By C. Wade, A. Swart, M. Dworzanowski

AngloGold Ashanti operate a pyrite flotation plant at their East Gold Plant, Acid Plant and Flotation Plant (EGAF) metallurgical complex within their Vaal River operations in the North West province in South Africa. The flotation plant feed is reclaimed pyrite rich tailings and the concentrate produced is used as the source of sulphur for the EGAF acid plant. The sulphuric acid produced is in turn used for the recovery of uranium at the Vaal River South uranium plant. The original flotation plant built in 1960 was based on the use of many small volume flotation cells and was becoming very expensive to operate and its age severely limited further operation. A decision was taken in 2005 to replace this plant with a new one based on fewer, larger volume flotation cells. This paper describes the benefits of using larger volume flotation cells in this new flotation plant when compared to the smaller volume flotation cells in the old plant. The benefits of the new plant include a smaller plant footprint, fewer flotation cells, fewer pumps, no distribution boxes, simpler piping, a greater flotation volume and a reduction in installed power. The saving in capital cost could not be quantified because of the age of the old plant. The savings in operating cost will arise from fewer operators, less maintenance and reduced power consumption. The new plant has not been in operation long enough to quantify the benefits in operating cost and metallurgical performance. However, recovery improvements can be expected given the greater flotation volume (increased residence time) and the installation of larger, more efficient flotation cells.

Jan 1, 2007

A physical modelling study has been carried out to simulate the slag-metal dispersion induced by a high-strength bottom gas injection. Water and kerosene were utilized to simulate metal and slag respectively. A water model of CLU (Creusot-Loire Uddeholm) vessel was used with three different nozzle orientations, namely, off-centre, triangular off-centre and centre. The gas flow rates changed from 0.00599m3/sec to 0.01081m3/sec. Height of heavy and light phases was kept fixed at 0.23 m and 0.02 m respectively. The dispersed phase holdup was determined at various axial and radial distances, gas flow rates, and tuyere configurations. The observations revealed that at a fixed gas injection rate, as the vertical distance increased in the centerline, straight off-centre orientation resulted in greater dispersed phase hold up values than those of the centre configuration and the triangular off-centre orientation. The dispersed phase holdup was found to increase with gas injection rate and decreased with axial distance. The variation of the dispersed phase hold up with the dimensionless axial distance and the gas injection rate was correlated by using the Modified Froude Number. The experimental values of the dispersed phase holdup were found to be in good agreement with the correlated values obtained from the modelling equations. The findings of the present study may be utilized in the ferroalloy refining vessels in terms of designing tuyere locations for optimum processing conditions.

Jan 1, 2004

By J. V. Simmons

Composite rock mass failures involve intact rock material as well as fracture and shear on existing defects. Experiences from open-cut coalmining in the Bowen Basin of central Queensland are that failures of this nature occur suddenly with little warning, and are much more common than classical structurally controlled failures. Geological conditions and mining practices in the Bowen Basin are described. The circumstances of a sample of composite failures are described in detail in the paper. From this experience it appears that several aspects of conventional geotechnical investigation and design practice have not contributed significantly to either predicting or controlling the risks associated with sudden failures. These practices are described as myths for reasons outlined in the paper. On the other hand, the reality seems to be that high initial stresses and stress changes caused by excavation lead by a process of extensional deformation to a critical stress condition within the rock mass, and that sudden collapse follows when that critical stress condition can no longer be sustained. It is concluded that learnings gained from underground excavations in rock may be more applicable to open pit excavations than previously thought, and that the processes of prefailure deformation require more careful study if we are to develop more reliable risk management controls.

Jan 1, 2006

In this study, the effects of slag compositions, slag amount, temperature, and carbon content of steel on the manganese and phosphorus distribution ratios during converter steelmaking were analysed using the classical regular solution theory, and industrial tests were performed using two 80 t top-and-bottom combined blown converters (duplex melting process). The results indicate that the slag amount, temperature, and carbon content in steel are the main factors affecting the manganese yield when converter slag compositions remain constant. The FeO content of the slag has a strong impact on the manganese distribution ratio, while the slag basicity and MgO content have no obvious effect. The calculations and experimental results show that the phosphorus distribution ratio increases sharply with increasing slag basicity R, but then decreases with the increase of MgO and MnO contents in the slag. The final slag in converter steelmaking should have the following characteristics: 3.5 < R < 4.5, 15% < (FeO) < 20%, and 6% < (MgO) < 8%. The slag amount should be controlled appropriately at the same time. The results of this investigation would be useful in deciding on the application of manganese ore in alloying and identifying the slagging regime in converter steelmaking.

Jan 1, 2014