Search Documents

By B. Kenealy

A typical deep shaft is President Steyn No. 2 in the Free State, where 9 tonnes of ore are hoisted at about 15 metres per second from 2378 metres below surface. The skips and attachments each weigh 7 tonnes and they are connected by 43 tonnes of rope, so that to hoist the 9 tonnes of payload, a total of 66 tonnes is accelerated from stand still to 55 km/h for each cycle, using an average of 3185 kilowatts of power in the process. The cycle time for the hoisting is 3.22 minutes. The peak power consumption is 6954 kilowatts, which determines the size of the motor used. Is this the right approach? Are larger skips moving at higher speeds the answer? Is there another way?

Jan 1, 1996

By W. J. Cruise

This paper reports on a test that was conducted underground in a mine for two years on the following: pipes coated with paint, fusion-bonded powder, metal, or impregnated tape; and aluminium, stainless-steel, 3CR12, and plastic pipes. It was found that the degree of corrosivity and mechanical damage increases substantially from the shaft of a mine towards the stope. Thus, the range of coatings that can be used successfully is fairly large in the shaft and haulageways, but corrosion-resistant materials, especially corrosion-resistant steels, need to be used close to the stope. A study of the relative costs involved showed the costs of pipes of low-carbon steel and unplasticized polyvinyl chloride to be lowest, and those of epoxy-coated steel pipes to be highest.

Jan 1, 1985

By R. J. Kriek, J. J. Cruywagen, W. J. Engelbrecht

Selective photo reduction, using the semiconductor TiO2 under UV irradiation, has been investigated as a possible recovery and/or separation method for the PGM's rhodium, palladium and platinum. The effect of pH value and concentration of the sacrificial reducing agent (ethanol) on the rate of reduction of Rh (III), Pd (II) and Pt(IV) ions have been determined separately for these ions as well as for some mixtures. Conditions favourable for the reduction and adsorption (or precipitation) on TiO2 have been established. It has been found that already deposited Pt or Pd metal promotes reduction of Rh (III) ions at a pH value where it would not otherwise be reduced. A method for the separation of a mixture comprising Rh (III), Pd(II) and Pt (IV), based on photo reduction and adsorption on the TiO2, is proposed.

Jan 1, 1995

By N. B. Strydom

The data on heat stroke cases reported during the past five years were examined to determine the influence of age on the incidence of heat stroke. Relating the age distribution of these cases to that of the total number of Bantu mine workers showed clearly that the older men run a significantly higher risk of developing heat stroke than the younger men. Although the number of Bantu over 40 years of age in the industry is less than 10 per cent of the total they nevertheless accounted for 50 per cent of the fatal heat stroke and 25 per cent of the nonfatal heat stroke cases during the period under review. Age must, therefore, be recognised as a causal factor in heat stroke and the worker over 40 years of age should be allocated to work on surface, or in cool areas or to non-strenuous and supervisory tasks in hot areas.

By R. N. Guest

The Tromp distribution curve was used in an evaluation of gravity separators treating a synthetic ore made up of silica and marker minerals of various relative densities. The results pinpoint differences in the concentration of particles of different sizes, and indicate how the grade of a concentrate is likely to vary with particle size. An increase in the feed rate increased the efficiency of the 'waterless' spiral concentrator that was tested, but the multiport spiral concentrator tested was more efficient. Both spiral concentrators were found to be more efficient than the pinched sluice and the shaking table that were tested. The method was found to be a useful way of evaluating gravity concentrators, but, for ease of analysis, care must be taken in the choice of marker minerals.

Jan 1, 1985

By N. C. Joughin

Potential for the mechanization of stoping in gold mines by N. C. JOUGHIN B.Sc. Eng., Ph.D. (Rand) (Member) The basic requirements for stoping machines are identified first by examination of the mining rates and productivities attained in conventional stoping, and then by examination of a series of problem areas associated with the shape of the reefs, rockbreaking, rockhandling, and the support and design of the machines. Some of the more important machines being developed are described briefly, and their principal features are compared with the basic requirements identified in the first part of the paper. An estimate of the potential demand for the different types of machines is given.

Jan 1, 1976

By G. G. Stanley

Mechanisms in the autogenous mill and their mathematical representation by G. G. STANLEY, B.Sc. (Eng.) (Wits.), M.E. (Queensland), Ph.D., (Fellow) The special characteristics of the autogenous mill are stated, and a suitable type of model for the mill is presented. Details of the test plant and experimental techniques for obtaining the data for model development are next given. followed by a discussion of the methods developed for the computation of the model parameters, namely the appearance matrix, the abrasion and crushing breakage-rate functions, and the discharge-rate function. Examples of results obtained with the model are given, and finally there is a brief account of confirmatory work on a fullscale autogeneous mill.

Jan 11, 1974

Reviewer: P.R. Janisch The progress of mining and metallurgy in Australia and their contribution to that nation's economy closely parallel those of South Africa. Australia's was the second of the three great gold rushes of the nineteenth century. It was centred on Bendigo and Ballarat in Victoria, and occurred in the 1850's, a few years after California's forty-niners. The California goldfield also gave birth to the now common term for a tabular gold bearing deposit-a 'reef'. Amongst the fortune-seekers were sailors who had jumped ship on hearing of the riches to be found on land. When the gold ran out, and with it the money, the sailors found themselves stuck on a reef'. But others, more canny, had accumulated the means to move on, and some came to the Transvaal on the news of the Barberton discoveries. One of them was George Harrison.

Jan 1, 1993

By M. A. von Below, I. C. Robinson

A mineral economic analysis of South Africa's mineral-beneficiation industry, comprising both economic theory and case studies, suggests that the domestic market has proved to be a more effective vehicle for promoting the establishment of advanced beneficiation projects than the availability of domestic raw materials. Although the domestic market plays an important role in the promotion of beneficiation by providing a secure outlet for sales, its most vital role is in the development of technological and marketing know-how that may give South African beneficiated products the competitive advantage required to penetrate export markets. The real wealth of a country lies primarily in the skills of its people rather than in its natural resources, and the domestic market plays a pivotal role in the development of these skills.

Jan 1, 1990

By C. Kliem

Geological, tectonic, geochemical and geophysical data were utilized for the mineral resource assessment of the Biga Peninsula in NW Turkey. During the deductive phase of the project multivariate statistical methods were applied to accentuate characteristic parameters which sufficiently describe the different types of Pb - Zn mineralization. The parameters most likely to be indicative of mineral occurrences were determined. In the following prognostic phase these parameters were further statistically treated to determine favourability indexes for the occurrence of a deposit within each cell of the training area. Preliminary results of probabilistic, univariate and multivariate methods are presented.

Jan 1, 1987

By S. Selmer-Olsen

New trends and developments in the production of ferro-silicon, ferro-manganese and ferro-chrome alloys are discussed, with emphasis on the general trend to the adoption of large production units. Problems which arise, both of a metallurgical and an electrical nature, due to the use of large electric furnaces, are outlined with specific reference to the limitations imposed by the power carrying capacity of Soderberg electrodes, the furnace resistance and the furnace reactance. The implications of combining high resistance within the furnace with good metallurgical operating conditions are illustrated by considering the production of ferro-silicon and ferro-manganese. The possibility of replacing electric furnaces used for ferro-manganese production, by large low shaft blast furnaces using oxygen enriched blast, is mentioned. The continued use of small electric arc furnaces for ferro-chrome production is also mentioned, and is ascribed to lack of ore suitable for treatment in large furnaces. Agglomeration of chromite ores appears to be a possible answer to this problem.

By H. E. Parkinson, Y. P. Chugh

About 90 percent of the coal mined underground in the U.S.A. today is mined by the room-and-pillar system. The productivity of the system dropped from about 14,1t per man-day in 1969 to about 7,3 t per man-day in 1978. Since 1974, the U.S. Department of Energy (formerly the U.S. Bureau of Mines) has been engaged in research to improve the production and productivity of the room-and-pillar system. The effort involves the development of integrated, automated, and remote-controlled equipment and systems including remote-controlled continuous miners, automated miner-bolters, automated extraction systems, continuous haulage systems for use behind miners, and remote-controlled equipment for miners, bolters, and shuttle cars. These systems are discussed briefly, the discussion being related primarily to coal winning, although the concepts could be utilized in room-and-pillar systems in mines other than coal mines.

Jan 1, 1981

By E. J. Magri

This paper describes a geostatistical study of the relative merits of diamond-saw sampling and conventional chip sampling, using results from experimental work carried out on Randfontein Estates Gold Mine and Western Areas Gold Mine. The diamond-saw sampling procedure is described, and it is concluded that this is a very efficient operation and leads to good-quality sampling that is clearly an improvement over conventional chip sampling. The study principally involved the computation of the errors of estimation of the mea gold value of mining panels for the two sampling methods, revealing that, in the normal production environment, the diamond-saw sampling method is a significant improvement over conventional chip sampling, as evidenced by the reduced estimation errors achieved. The question of optimum sample spacing is discussed, and it is concluded that the required spacing for chip sampling needs to be smaller than for the diamond-saw method.

Jan 1, 1986

The Institute has concluded an agreement with the Chamber of Mines whereby the Chamber Librarian maintains a section in the Library for the Institute. Surface effects of underground mining South Africa is blessed with vast mineral resources. It is essential to exploit those reserves if the country is to remain economically viable. Surface-mining equipment The Goldfields Mining Expo '86 is to be held in Kalgoorlie, Western Australia, from 30th October to 1st November, 1986, in conjunction with the Annual Conference of the Western Australian School of Mines. Mintek reports Report M142D Characteristics of gold and pyrite flotation at the Chemwes plant. (1st issued May 1984.) Report M159D Beneficiation tests on andalusite ore from the Marico district. (1st issued Aug. 1984.) Report M164D The recovery of tungsten from South African low-grade schee/ite concentrates. (1st issued Sep. 1984.)

Jan 1, 1986

By J. A. Ryder

A high proportion of damaging rockbursts are thought to be underlain by seismic events that represent shear or rupture along planes of weakness (faults, joints, dyke contacts). Such events are controlled by shear stresses and friction properties along the plane. Excess shear stress (ESS) is a measure that can be evaluated numerically and that, in principle, can be used in an assessment of the possible magnitude and relative likelihood of seismic activity. Methods for the calculation of ESS in practical mining contexts, and for the estimation of the magnitudes of possible seismic event progressions, are briefly reviewed. The effects of variables such as depth, stoping width and, in particular, virgin horizontal stresses on general shear-type seismic hazards are investigated. Attempted back-analyses of two large rockbursts are described.

Jan 1, 1988

Prediction of the performance of explosives In bench mining by C. M. LOWNDS, B.Se. Hons (Rhodes), Ph.D (Cape) (Visitor) Some of the problems encountered in the calculation of the relative weight strength of explosives are discussed, and a realistic model of the behaviour of explosion products in a borehole is proposed. The heat flow from condensed to gaseous products is calculated as a function of time, and the relationship between the pressure and the volume of the product gases is found by a consideration of the compression of the rock between radial cracks. Work done on the burden is assumed to cease when the cracks first appear at the face. Reasonable values of burden and crack velocities are obtained from the model. Calculations of the relative weight strengths of aluminized mixtures of ammonium nitrate and fuel oil show that the increased density resulting from the addition of aluminium is the main advantage to be gained.

Jan 2, 1975

By D. J. Bosman

The impoved densification of sludge from neutralized acid mine drainage. by D. J. BOSMAN, B.Sc., (Member) The paper describes an investigation aimed at finding a solution to the accumulation of acid mine drainage in the old workings at Coronation Collieries, Kromdraai. The problem involved the neutralization of the acid in the water, without the large volumes of sludge and the large amounts of dissolved solids that usually result from neutralization. Pilot-plant work on the site using a limeneutralization process developed at Bethlehem Steel Corporation (U.S.A.) showed this to be a feasible method. A sludge of 22 per cent density was obtained under optimum operating parameters. The amount of suspended solids in the overflow water was very high, but this does not give rise to concern because the full-scale plant at Kromdraai will practise secondary sedimentation by running the thickener overflow through large dams with a theoretical retention time of 25 days. An analysis of the theory underlying the process is also made.

Jan 4, 1974

By M. W. Grodner, J. Maaren, G. Guler, J. K. Schweitzer

The selection of the most suitable mechanized mining strategy has to consider the geotechnical environment in which it will be operating. A mechanized mining method or machine is designed to a given set of specifications to work within an environment. The geological conditions that define this environment are fixed—detailed information of these conditions for design specifications is thus critical. Two major classes of geotechnical parameters are defined—critical and design. The critical controlling factors are a result of mineral composition, size, shape, abundance, assemblage and associated texture, as well as discontinuity type and orientation. Design parameters are specific to each deposit, and their nature cannot be broadly described, as with the critical factors. It is shown that for major deposits in South Africa, namely the Witwatersrand Basin (gold), the Bushveld Igneous Complex (PGEs) and the Karoo Coalfields that by incorporating geological and geotechnical information that appropriate mechanized mining methods can be deduced, and that the performance and design parameters of specific technologies can be determined

Sep 1, 2001

By B. Z. Weiss, N. R. Comins, F. Blum

Some aspects of the mechanical behaviour of chromium-containing dual-phase 3CR12 steel were investigated as a function of the temperature and strain rate. The yield stress was found to depend on both the temperature and the strain rate, with no substantial differences between the longitudinal and the transverse directions. The strain-rate sensitivity decreased with increasing temperature. The yield stress could be presented as a function of a temperature-strain-rate parameter. Impact test results showed substantial differences between the energy absorption of the transverse and longitudinal specimens above the ductile-brittle transition temperature. Changes in energy absorption with temperature were gradual for specimens in both orientations, and the transition from ductile to brittle behaviour occurred between 373 and 173 K. Strain rates ahead of the tip of notches with different geometries were calculated and measured experimentally.

Jan 1, 1990

The optimization of sample spacing In South African gold mines by J. M. RENDU*, Eng. Se.D., M.S. (Min.) U.S.A. (Graduate Member) A first attempt is made at optimization of sample spacing in South African gold mines. The De Wijs model, which is shown to give a good representation of the geostatistical properties of gold values, is used to analyse the influence of the distance between samples along a stope face on the error of estimation of the stope value. The influence of other factors such as the face advance before resampling, the sample density, and the stope size, is also considered. Practical conclusions are drawn concerning the optimum sampling policy to be followed in various situations, and it is shown that sampling on a regular grid does not necessarily give the best results.

Jan 4, 1976