Search Documents

A Seismic Hazard Scale (SHS) has been developed to provide a practical seismic hazard assessment tool applicable to mine site personnel. It has been applied to seismic data sets from numerous Western Australian mines. The SHS is applicable when quantifying seismic hazard on a mine wide scale, on a mining block scale, and on a local cluster-by-cluster scale. Spatial mapping of variations in seismic hazard is a particularly powerful application of the scale. The SHS is sensitive to temporal increases in seismic hazard. It has also been shown that the SHS can be applied to estimate seismic hazard when seismic monitoring data are not available. The SHS is a simple derivation of the Gutenberg-Richter relation. There are assumptions and limitations to the SHS that need to be considered when applying it to mine seismicity data.

Jan 1, 2004

By A. D. Storrie

An underground wet shotcrete trial was completed last year to determine the effectiveness of wet shotcrete as an alternative support mechanism to dry shotcrete in the kimberlite environment. The wet shotcrete was manufactured at the underground batch plants, transported to site using an agiecar and transferred to the shotcrete pump. The wet shotcrete is pumped to the nozzle where compressed air at 7 bar and an accelerator, Meyco SA 160, is added and enables the shotcrete to be placed successfully onto the tunnel wall. No tunnel guard was previously placed on the sidewall and hangingwall. Geotechnical testing indicates that the Grace fibre performed extremely well with the energy absorption tests at 7 kg/m3and 8kg/m3where both achieved over the mine requirement of 750joules. The Grace fibre and wet shotcrete mix also achieved a compressive strength in excess of 55 MPa, well above the 45 MPa requirement for Premier Mine. The recommended wet shotcrete mix design is therefore based upon: [Material/ CriteriaQuantity/m3Units ?Lafarge 42.5 Duratech500kg ?Condensed silica fume40kg ?Rayton Sand1.558Ton ?Delvocrete stabilizer 103.6litres ?Glenium 27CH5.4litres ?Meyco TCC 7355litres ?Water230litres ?Meyco SA16025litres ?Fibre8kg ?Cement/Water Ratio2.35? ?Water/Cement Ratio0.43? ?Flow615 mm] If the wet shotcrete system is implemented there is a potential for Premier Mine to make major savings. In South Africa there are two suitable wet shotcrete machines available for the mining industry, the Spreymec, manufactured by Tamrock and the Fermel/Meyco wet shotcrete machine. The Spreymec is a fully imported machine. The Fermel component is manufactured in South Africa and the Meyco shotcrete components are imported and supported by MBT (Master Builder Technologists) in South Africa. The Fermel/Meyco machine is assembled in South Africa. Premier Mine has allocated some R2, 100,000 towards the implementation of the wet shotcrete system. If implementation is successful there should be an internal rate of return gain of 76% with regard to this project.

Jan 1, 2001

By T. A. Muhlare

"Large quantities of slag are produced every year and dumped on slag heaps around the world, posing a potential environmental threat due to contained heavy metals content. Slags are waste minerals produced during furnace smelting of minerals. The contained values of base metals may be released into the environment under natural weathering conditions polluting ground and underground water. Copper losses into slag are a continuous problem in pyrometallurgical smelting operations. Due to shortage of ore concentrate, various mining operations have initiated the recovery of copper from dumped slag. The typical process uses crushing, milling and flotation. These operations create excessive liner wear rates during crushing and milling because the bond work index of copper slag is 22 kWh/t and this is considered a very hard slag. The process also has reduced flotation recoveries and requires high flotation reagent consumption. The present work shows that digestion of the milled copper slag slurry with concentrated sulphuric acid at a temperature of 250oC forms a solid cake and leaching of the solid cake with water is a possible option. However, the consumption of sulphuric acid can have a considerable cost on the recovery process. This can be limited by producing a leach residue containing gypsum and silicate materials as amorphous silica which are suitable for use as an additive for Portland cement. Laboratory results show that 90% copper recoveries can be achieved. The leaching is conducted to prevent silica gel formation and iron co-extraction. Leaching is optimum if silica gel-free solutions and good filterable residue are obtained. INTRODUCTION Slag is a waste by-product of smelting and converting operations in metallurgical plants. Both smelting and converting operations are aimed at iron separation from base metal sulphides in non-ferrous metallurgy. The iron sulphide component of the ore or concentrate is oxidized to iron oxide at higher temperatures in the molten form, and then fluxed with silica and other oxide rock minerals to produce fayalite (2FeO•SiO2) slag (Schlesinger et al., 2011). Slags are generally deposited on dumps and considered to be unreactive materials. Smelter copper slag contains significant concentrations of several potentially toxic elements, including arsenic, lead, cadmium, barium, zinc and copper. These elements can be released into the environment under natural weathering conditions and cause pollution of soils, surface waters and groundwater (David, 1998)."

Jan 1, 2015

By H. Dong

This paper presents a heat conduction model to determine the erosion profile of freeze linings in a ferronickel submerged arc furnace. Kirchhoff transformation was adopted to simplify the nonlinear equation governing heat conduction. The boundary element method (BEM) and Nelder-Mead simplex optimization method were employed to solve an inverse heat conduction problem. Erosion profiles could be obtained when calculated temperatures at sensor locations agreed well with measured temperatures. The model was validated by comparing the heat loss through the linings, which was calculated by BEM and integral operation after erosion profiles were obtained, with the value calculated from industrial data such as actual power consumption, tap-to-tap time, and ferronickel output. The optimal solution for the erosion profile could be acquired when the difference in heat losses calculated by these two methods is at a minimum.

Jan 1, 2014

By P. Mbele

Iron ore concentrate is not easily transported to, or processed in, ironmaking plants, therefore it is necessary to agglomerate. This paper will determine the possibility of agglomerating Sishen concentrate into suitable ironmaking feedstock. Pelletizing is one of the conventional and preferred agglomeration processes for iron ore concentrate investigated at Kumba Value-In-Use Laboratories. Sishen concentrate was mixed with binder, and then pelletized using a laboratory pelletizing disc; afterwards the green pellets were indurated at high temperatures to give strength high enough to survive handling and lessen disintegration in the shaft during ironmaking. Sishen pellets have satisfactory physical and metallurgical properties which make them suitable feedstock for the direct reduction processes. These were tested under Midrex shaft operational conditions and performed well, with a metallization of 94.47% being attained.

Jan 1, 2012

The compilation of the sampling nomogram is an essential tool in the optimization of a sampling protocol and allows the operator to track the change in relative variance of the sampling error (the Fundamental sampling error) during steps of comminution and mass reduction in the process of recovery of the aliquot for analysis. The data required for the compilation of the nomogram are centred on the sampling constant K and the exponent, alpha (a) of the nominal fragment size. Five methods for establishing K have been identified, but two of them, the duplicate sampling analysis method and the heterogeneity test method purport to provide such constant. The step by step procedure for each of these two methods was examined using broken ores from three mines, Mponeng mine, Kloof mine, and Lily mine. Two of these mines (Mponeng and Kloof) are typical Witwatersrand-type gold mines, and the third is an Archaean-type shear related gold deposit situated in the Barberton Greenstone belt. The results suggest that the factor K derived using the heterogeneity test is very accurate, but applies only to a single size fraction in the spectrum of comminuted materials. The calculation of gold grain sizes using this method appear to be too small and do not conform with the results from detailed mineralogical studies. The factors K and alpha derived using the duplicate series analysis are appropriate for use across a wide spectrum of comminution sizes and also provide realistic gold grain sizes, comparable with the equivalent circular diameter of gold grains identified in mineralogical studies of the ores.

Jan 1, 2010

By A. S. Macfarlane

This paper describes how knowledge of the orebody morphology and ore morphology can be used to optimize the planning, mining, and metallurgical output from an open pit copper mining operation, such as to significantly increase the stability of the whole value chain process, and increase the reliability and value of the process outputs. In the case under consideration, the orebody contains both copper and cobalt. This in itself provides a challenge, in that the two metals do not occur in consistent ratios across the orebody as a whole. Furthermore, mineralogical differences within the orebody have a significant impact on plant performance in terms of throughput rates, acid consumption, and recoveries. In order to stabilize and optimize the plant performance, it is necessary to firstly have a complete understanding of the geometallurgical factors that affect performance, and then to have a sound knowledge of how these are distributed within the orebody. These models then inform the mine planning strategy that optimizes cash flow and NPV, and also allow the development of a stockpiling strategy that not only stabilizes the plant, but also allows variations in the plant feed according to ore type and grade in volatile price scenarios. Integral to the realization of these opportunities is the establishment of an appropriate measuring, control, and reconciliation system, customized to the optimization objectives. The paper describes how all of these factors and strategies can be integrated to produce optimal value from the orebody through to final dispatched product. It also shows the significant value that can be released through such an approach.

Jan 1, 2014

By S. Kamalpour

It has been observed that the productivity of ferromanganese furnaces, and the stability of metal and slag compositions, vary considerably according to the type of coke used as reductant. However, the desired properties of coke for optimum furnace performance are not well understood. In this investigation, the behaviour of four cokes, which exhibited a wide range of performance in ferromanganese production, was investigated by means of laboratory simulations of reducing conditions in the furnace. The Stationary Charge in Controlled Environment (SCICE) technique was used to simulate the conditions in the furnace shaft. Batches of raw materials, mixed in the same proportions as used in practice, were heated at fixed rates to 900, 1100 and 1300°C then cooled. The mass loss was used as a measure of the degree of reduction. Conditions in the lower part of the furnace were simulated by means of melt-reduction experiments in which lumps of coke were drilled out to form crucibles in which enriched ferromanganese slags were reduced at 1500 and 1550°C then cooled. An examination of the raw materials and the cooled, reacted charges using a variety of analytical and characterization techniques enabled the sequence of reaction and changes in morphology of the raw materials to be followed. This enabled an understanding of the behaviour of the cokes during reduction to be developed, which was then used to explain the observed performance of the cokes in practice. By relating the observed behaviour of the cokes in the laboratory tests to measurable properties of the unreacted cokes and to their observed performance in practice, it was shown that to achieve high productivity and good furnace performance, cokes should be selected to have moderately high reactivity towards CO2 (Boudouard reactivity) relative to conventional iron blast furnace cokes.

Jan 1, 2004

At the exploration stage for new mining projects or for medium- and long-term areas of existing mines (typical of South African gold mines), drilling data is on a relatively large grid. This grid is normally larger than the selective mining units (SMUs). Direct estimates for the SMUs and also of much larger block units will then be smoothed due to the information effect and the high error variance. Any capital-intensive project decisions made on the basis of any of the smoothed estimates will tend to misrepresent the economic value of the project or operation, i.e. the average grade of blocks above cut-off will be underestimated and the tonnage overestimated for cut-off grades below the mean grade of the orebody. This paper presents a direct approach technique for deriving recoverable resources, referred to as localized direct conditioning (LDC), designed to correct smoothing effects and also to provide support corrections.

Jan 1, 2014

By P. L. Duncanson, J. D. Toth

Since 1995, when "freeze lining" refractory systems were introduced to the ferroalloy industry, they have gained in popularity, due to the freeze lining?s reputation for reliability, safety, and the contribution it makes to profitability. As with many popular and effective technologies, however, the freeze lining has spawned low-cost pretenders that claim the "freeze lining" name. On the surface they appear to contain some of the components of the technology, such as thermally conductive materials, but they fail to incorporate all of the principles that define a true Freeze Lining. The term "freeze lining" refers to the refractory system?s ability to maintain a temperature profile that is low enough to freeze a layer of process material on its hot face, which insulates the refractory and prevents direct contact with molten metal and slag. In doing so, the common wear mechanisms found in the submerged arc furnace - chemical attack, erosion, and thermal stress - can be prevented. These wear mechanisms are all related to high temperature; thus, they are prevented by maintaining low temperatures. Certain refractory properties and design concepts are absolutely necessary for the lining system to function as a true Freeze Lining. The paper explains these requirements and why they are important - the Truth of freeze linings - and further explains why systems that ignore one or more of these requirements cannot claim to be freeze linings, thereby exposing the Myths.

Jan 1, 2004

By T. Wettainen

Malmberget town is located in northern Sweden, approximately 70 km north of the Arctic Circle. Parts of the town overlie more than 20 iron orebodies, consisting mainly of magnetite with smaller quantities of haematite. The mine is operated by the mining company LKAB. Mining started in the 17th century, but not until the railway to the coastal city of Luleå was completed in 1888 did large-scale production commence. Around 1920, mining proceeded underground and today sublevel caving is the only mining method used. Sublevel caving causes subsidence of the ground surface, and buildings and residential areas have been relocated due to the mining activities for more than 50 years. The number of seismic events accompanied by strong ground vibrations is now increasing. In 2008 the mine received a permit from the Environmental Court of Sweden to increase production to 20 Mt of crude ore per year. A prerequisite for the permit was that the mine conducts a number of investigations regarding the environmental impact on the residents of Malmberget. One of these investigations concerned how seismicity will change as production increases and what measures could be taken to reduce inconvenience to the town residents. Today the mine possesses an extensive seismic monitoring system with more than 180 underground and surface geophones. For this study, eleven seismically active volumes in Malmberget mine were identified, and for each of them, a yearly future maximum magnitude interval was estimated based on the current production plan. Relationships between historical seismic events and measured ground vibrations in the town of Malmberget were established, and future ground vibrations caused by expected seismic events were estimated using a probabilistic approach. The outcome was the number of intervals of expected ground vibration per year and per monitoring point. Possible measures to reduce inconvenience for the town residents include blast restrictions, sequencing, and possibly preconditioning. The ultimate long-term solution is an almost complete relocation of Malmberget town. This process has recently been formalized and LKAB is taking an active part in realizing this goal.

Jan 1, 2014

By G. L. Smith

This paper consolidates the key elements of seven contributions, on strategic long-term planning, to two of the three international conferences on Strategic versus Tactical approaches in Mining held over the period 2005?2008. The holistic concept of strategic long-term planning as developed and implemented at Anglo Platinum is described. Consideration is given to the planning cycle, principles supporting the construction of the long-term plan, and aspects of unique best practice as developed in Anglo Platinum. Further description of Anglo Platinum?s approach to corporate governance, including the processes, methodology, systems, unique tools and techniques that are applied to value and select capital investment options is also given.

Jan 1, 2009

By S. G. Ercelebi

In surface mining operations, truck haulage is the largest item in the operating costs, constituting 50 to 60% of the total. In order to reduce this cost, it is necessary to allocate and dispatch the trucks efficiently. This paper describes shovel and truck operation models and optimization approaches for the allocation and dispatching of trucks under various operating conditions. Closed queuing network theory is employed for the allocation of trucks and linear programming for the purpose of truck dispatching to shovels. A case study was applied for the Orhaneli Open Pit Coal Mine in Turkey. This approach would provide the capability of estimating system performance measures (mine throughput, mean number of trucks, mean waiting time, etc.) for planning purposes when the truck fleet is composed of identical trucks. A computational study is presented to show how choosing the optimum number of trucks and optimum dispatching policy affect the cost of moving material in a truck-shovel system. Keywords: Open pit mine, equipment selection, dispatching, linear programming, closed queuing network theory

Jan 1, 2009

By G. C. Smith

Process control applications in the minerals processing industry have grown extensively over the years due to the many benefits derived, both financially and operation-wise. Although control theory is widely known, conventional control does not address many of the problems posed by minerals processing circuits. Some of these problems include interactions between process units, large dead times, few and sometimes unreliable measurements of process variables, non-linear systems, disturbances entering the process, processes with varying dynamics, and many more. For the past 26 years Mintek has been active in the field of providing specific, customized solutions for the minerals processing industry. This paper focuses specifically on applications in milling and flotation control. The underlying control principles have been applied to a wide range of other processes including submerged arc furnaces. Advanced control application is implemented on a common advanced control platform, called the PlantStar. Much innovation has been brought to the fore in terms of adapting theoretical techniques and developing new methods to resolve specific milling and flotation circuit issues by using process control. The general approach adopted by Mintek when implementing advanced control is to enforce stabilization of the process as a solid foundation for optimization strategies to be built upon. In doing this, a robust control solution is presented, and the end result is flow and level stability, better product quality regulation, increase in throughput and a stable feed to downstream processes. The MillStar advanced milling control system ensures that the milling circuit is at all times easy to operate while achieving optimum product quality and throughput. Stabilization should include product size regulation and sump level control. Another important aspect of stabilization control is the handling of milling circuit constraints without introducing cyclical behaviour and with minimal disturbance to the final product quality. Process constraints may include factors such as process water limitations, cyclone feed density, and cyclone underflow angle. An optimization strategy should be developed to increase the mill throughput without affecting product quality or introducing mill overloads. The relationship between solids feed and power draw is examined and manipulated for optimization. The interactive nature of flotation circuits and the presence of recirculating streams tend to make satisfactory control almost impossible with conventional techniques such as PI (Proportional plus Integral) or PID (Proportional, Integral and Derivative) control. The FloatStar Level Stabilizer simultaneously considers all the flotation levels in a circuit by use of a multivariable algorithm, and takes compensating action in anticipation of disturbances. The FloatStar Flow Optimizer is an optimization strategy that controls the concentrate flow rate between various sections of a flotation circuit (e.g. Rougher ?Cleaner; Cleaner ?Recleaner). By controlling the concentrate flow between the sections, the mass pull, circulating loads and residence times of the circuit can be stabilized, thereby enhancing the performance of the flotation process. Optimizing grade and recovery are coupled with the dynamic optimization of circulating flows. The FloatStar Grade-Recovery Optimizer will maximize the grade in a section, whilst ensuring that recovery or any other process specific limits remain within predefined limits. With successful applications on several milling and flotation plants worldwide processing amongst others PGMs, gold, copper and nickel, Mintek has shown that it is a leader in milling and flotation control innovation

Jan 1, 2004

By B. Samanta

LHD (load haul dumper) is now used as a loading machine for intermediate mechanization in underground coal mining. For survival in the intense competition in the global business environment in recent years it is essential that LHD machine should be reliable and maintained effectively and efficiently. This paper seeks to study the reliability, availability and maintainability (RAM)of an LHD machine with failure and repair data by Markov modelling. The constraints and reasons for machine unavailability are outlined. The reliability and maintainability of an LHD and its subsystems are evaluated. Possible modification or design alternatives are highlighted. Reliability and maintainability of an LHD system are disappointing. There is room to take decisions on optimal maintenance planning and machine improvement from this analysis. Keywords: reliability, availability, maintainability, Markov model, LHD

Jan 1, 2004

By R. Cao

Geostatistics was initially developed in the mining sector, but has been extended to other geoscience applications, including forestry, environmental science, soil science, and petroleum science and engineering. This paper presents methods, workflows, and pitfalls in using geostatistics for hydrocarbon resource modelling and evaluation. Examples are presented of indicator variogram analysis of categorical variables, lithofacies modelling by sequential indicator simulation and hierarchical workflow, porosity modelling by kriging and stochastic simulation, collocated cokriging for integrating seismic data, and collocated cosimulation for modelling porosity and permeability relationships. These methods together form a systematic approach that can be effectively used for modelling natural resources.

Jan 1, 2014

By P. F. Ledwaba

South Africa?s Northern Cape Province houses a variety of gemstone minerals. Diamonds remain the primary gemstone in the province, but there are also tiger?s eye, sugilite, rose quartz, jasper, amethyst, amazonite, tourmaline, and topaz deposits. This paper gives an overview of the tiger?s eye (TE) mining sector in the Northern Cape, with the objective of assessing the potential of TE to contribute to job creation and poverty alleviation in the province. Mining of TE started in 1803, but gained momentum during the 1960s. Mining is conducted on a small-scale basis, and in most cases without any legal framework. The majority of the residents are not benefiting from TE. It has been reported that an estimated R700 000 to R800 000 worth of TE is leaving the country every week through illegal trading. The potential for TE mining to contribute to socioeconomic development is hindered by illegal operations, lack of technical skills and knowledge, exploitation by dealers, lack of market information, community rivalries, and absence of value addition. A multi-stakeholder approach is needed to formalize the sector and reap the benefits. Mintek is spearheading a TE project in the Prieska area of the Northern Cape, which aims to establish a gemmological centre where TE can be beneficiated into saleable and high-value products..

Jan 1, 2014

Physical testing of rock support for rockbursting conditions has been carried out for over 40 years. A review of this testing shows that it has been mostly component?based, rather than actually testing support systems. Further, it is concluded that none of the testing is truly representative of rockburst loading in a similitude sense. Similitude conditions are not achievable, mainly because the real conditions in a rockburst event, such as seismic source location and magnitude, wave frequencies, amplitudes, and interactions, are not all known. Because such information is not available, and because the results of all testing carried out to date have not been able to define, for support design purposes, the capacity of support systems, ongoing physical testing of rockburst support systems is essential. It is essential that the test should simulate, or actually take place in, a supported rock excavation. A rock support system is a combination of individual support components that work together to retain and contain the rock. In doing this, the components are subjected to loading by the rock and to interactive loading between one component and another. It is necessary to prove the capacity of such rockburst support systems by subjecting them to severe loading, as in direct blasting. The direct blasting approach, pioneered more than 40 years ago, probably still provides the greatest validity as a significant test of rockburst support capabilities, even though it does not simulate a rockburst. Direct blast testing of rockburst support systems in a surface environment, such as in a quarry or on exposed rock cutting surfaces, could represent a practical development of the approach, facilitating the execution and monitoring of tests.

Jan 1, 2012

By N. K. Singo, J. D. Kramers

The reprocessing of tailings resources to extract gold on an industrial scale has become common practice. While these projects are common in the Witwatersrand basin, similar low-technology processes are not operational in smaller goldfields. This study explores the possibility of reclaiming the tailings dump of the Louis Moore Mine in the Giyani Greenstone Belt, investigates potential hazards to communities in the vicinity, and identifies mitigation strategies. Auger samples were taken from the Louis Moore tailings at depths of up to 5 m. Aqua regia leach analyses show Au concentrations of up to 1 g/t. Inferred estimations based on ordinary kriging (OK) and inverse distance weighted (IDW) methods put the residual Au resource in the Louis Moore tailings dump at 0.20 t. Reworking the tailings is viable, although a potential environmental risk exists in the form of elevated arsenic concentrations. Further exploration is required to determine the mineralogical associations of Au and As. Tailings reworking would assist in raising funds for mine rehabilitation. The secondary tailings could potentially be repurposed, which would provide employment and facilitate community development, as well as deliver environmental benefits.

Jul 1, 2021

By D. Boshoff

The ability of an explosive to break rock is influenced considerably by the extent of confinement in the blasthole. It is believed that confinement is improved by the use of adequate stemming. The aim of this paper is to present the results of the first and second stages of developing a stemming performance testing rig for small diameter boreholes. The rig was used to compare and contrast the performance of different designs of products. The results showed that different stemming products have differences in terms of their functionality, which can have a major impact on the efficiency of rock breaking. Two test procedures were used, one through the exclusive use of compressed air and the second using a purpose-built high pressure test rig with small quantities of explosives. Both tests were used to identify and evaluate the ability of various stemming products to resist the escape of explosive gas through the collar of a blasthole. An investigation was done to determine the types of stemming products most commonly used in South African underground hard rock mines, and these products were used during the tests. The first stage of tests using compressed air only did not prove adequate to predict with certainty the pressure behaviour in the borehole of a particular product under high pressure conditions. The purpose-built high pressure test rig also did not prove to be a very effective tool to test stemming products under high pressure conditions. The test rig incorporated only the effect of gas pressure on the stemming product, and excluded the effect of the shock wave. This study therefore proved that to take into account only the gas pressure generated in the blasthole is not sufficient to effectively test stemming product performance.

Jan 1, 2011