Search Documents

By David A. Monaghan, Kenneth R. Maser, Adi R. Gurdar, D. Randolph Berry

APPENDIX B - DEVELOPMENT OF FOAM-CONCRETE SLURRY MINE SEALANT 1. Introduction This appendix describes the results of an experimental development and laboratory evaluation of foam-concrete as a rapid setting, lightweight, self-supporting mine sealant material. Foam concrete, otherwise known as Aerated Concrete, is a form of lightweight concrete whose structure consists of air bubbles held together by a hardened cement mortar. Its principal applications are found in roofing, insulation, shock absorbing, and backfill. The air bubbles in foam concrete are formed either by chemical reaction in the wet, placed mortar, or by introducing a stable foam into the mortar during mixing. The mortar is usually a cement slurry with fine sand or fly ash as filler. Our attention focused on preformed foam concrete, since this is most adaptable to field applications. Equipment is available,* which simultaneously mixes and pumps a slurry of foam concrete. Such a slurry can be produced at a rate of up to 50 yards/hr and has been pumped in a 2-inch-diameter hose 1000-feet horizontally and 250 feet vertically up without significant bubble deterioration. One very attractive feature associated with the use of foam concrete concerns site logistics. Foam concrete can be generated with densities as low as 20 lbs/ft3, and hence the total number of

Jan 1, 1973

By Wilton Johnson

Native asphalt was produced by four companies in two States, Texas and Utah. Bituminous limestone, used primarily as a paving material for street and road repair, was produced by one firm. R. L. White Co., Dabney Quarry, Uvalde County, TX. Gilsonite, a solidified hydrocarbon found only in Utah and Colorado, was mined by three firms: American Gilsonite Co., a division of Chevron Resources Co. (a subsidiary of Standard Oil Co. of California); Ziegler Chemical and Mineral Corp.; and Hydrocarbon Mining Co. (a subsidiary of Oberon Oil Inc., a Utah corporation), from properties in Uintah County, UT. Gilsonite is used for a variety of purposes including automobile bodysealer, light-weight aggregate for cement used in oil well drilling, asphaltic building board, protective coverings, anticorrosive paints, and roofing compounds. Gilsonite production in 1985 declined 57% owing primarily to reduced oil well drilling activity. The value per ton was essentially unchanged.

Jan 1, 1987

By E. G. King

Enthalpy increments above 298 K were determined by the Bureau of Mines for magnesium hydroxide (brucite) between 298 and 900 K by the method of drop calorimetry. Enthalpy and entropy increments from this investigation were combined with other data from the literature to calculate absolute entropies, free energy functions, enthalpies of formation, Gibbs energies of formation, and equilibrium constants of formation from 298 to 900 K. By the use of published PVT data for water, a table of Gibbs energy change was given for the reaction MgO (periclase) + H2O = Mg(OH)2 (brucite) as a function of temperature and pressure.

Jan 1, 1975

By James L. Hendrix

A study was made of the United States Bureau of Mines' chlorine-oxygen leaching process for complex sulfide concentrates. The investigation sought to determine the kinetic order and IT mechanisms involved in the reactions betweens sphalerite, and galena with chlorine. The influence of copper on the extraction rates was also studied. It has been shown the rates of reaction of chlorine in aqueous solutions with sphalerite and galena are both zero order at 373K with the rate limiting step being the chemical reaction. Addition of cupric chloride increased the extractions of both lead and zinc.

Jan 1, 1980

By H. B. Carroll

The Bureau of Mines investigated the adaptability of the Meteorology Research Inc.2 (MRI) nephelometer and the Sinclair-Phoenix smoke meter for use in routine, analytical, smog-chamber experiments and to compare their responses to aerosol during these experiments. Both instruments' sampling systems were modified--smaller size sample input systems were studied using the nephelometer and a secondary sample system was added to the smoke meter to allow measurement of Aitken or condensate nuclei. Both instruments were easily adapted for use with small smog chambers and both displayed good precision and sensitivity to aerosol. A correlation was shown to exist between the two instruments' responses to aerosol. This correlation makes it possible to report the Sinclair-Phoenix measurements in visibility and/or mass units if desired.

Jan 1, 1973

By Michael J. Brnich

Since 1991, Pittsburgh Research Center (PRC- formerly part of the Bureau of Mines) researchers have recorded extensive interviews with 30 individuals who are experts in the area of mine emergency response. These individuals, who have an average of 35 years of mining experience and 29 years of mine emergency response experience, related stories and observations from events that they experienced during their combined 850 plus years in mine emergency response. The purpose of this effort was to gather information that could be passed onto both today?s and tomorrow?s mine emergency responders to train and guide them in handling future events.

Jan 1, 1997

By J. C. Edwards

The Bureau of Mines developed a mathematical model that decribes the interaction of an automated breathing and metabolic simulator, or lung, with a self-contained· self-rescuer that is supplied compressed oxygen. The model can be used to predict the gas partial volumes of 0z, Nz, and COz in the lung and in the self-rescuer breathing bag for a prescribed metabolic state that characterizes the lung. Nonlinear rate equations are used to describe the temporal evolution of the gas partial volumes. A numerical procedure was established with a FORTRAN computer program to solve these equations, which correspond to a given metabolic state. Examples are presented of applications of the model to predict bag volume and bag oxygen concentration changes with time when the bag is controlled by an automated breathing simulator. Under certain restrictive conditions, the model equations can also be used to analytically pre-dict the time required for the bag to reach a maximum or minimum volume. The model equation in this latter case was extended to transi-tions between metabolic states, with transitions described as exponential growth or decay processes.

Jan 1, 1985

By Suzann C. Ambrosio

The mineral industry in Burundi continued to be a minor contributor to the 1980 gross domestic product (GDP) estimated at $293 million in constant 1970 prices.2 Mineral export revenues, primarily from cassiterite, increased by a factor of 15 between 1979-80, reaching approximately $434,000 by yearend 1980. Gold, bastnasite, colombite-tantalite, and wolfremite continued to be exploited on a small scale, using manual and semimechanical methods. Despite a sharp decline in mining activities during 1979, attributed to a lack o? profitability and shortage of construction materials, the mining sector exhibited signs of recovery during 1980. The mineral exploration budget grew 32% over 1979 levels and was equivalent to approximately $42,000 in 1980. In addition, the Burundi Geographical Institute (IGE BU) was created in September 1980 and given responsibilities to collect cartographic, topographic, hydrogeologic, and other geomorphological data., SONIBUROM, the Burundian and Romanian Government joint mineral corporation, conducted mineral deposit inventories during 1979-80 and has been charged with exploiting some of these as yet unspecified resource areas. Another Burundian-Romanian effort, called Mabaya-Butahana, was initiated to search for gold deposits. Meanwhile on the Ruzizi plain, alluvial gold prospecting, with an estimated grade between 0.2 to 1.0 gram per ton, was carried out on a small scale.

Jan 1, 1982

By A. May

Florida has accumulated about 400 million tons of phosphogypsum, a mineral process waste generated in the production of fertilizer, and is adding 30 million tons to this annually. To minimize storage of this waste and reduce potential environmental effects, the Bureau of Mines conducted research into utilizing the phosphogypsum, by identifying and developing high-volume uses for this material. Admixtures of phosphogypsum, fly ash, and lime that could produce a coarse aggregate suitable for road construction were investigated. Using phosphogypsum with asphalt, cement, cement-kiln dust, silica, clays, and oxychlorides to pro-duce aggregate was also examined.

Jan 1, 1985

By Oliver Bowles

[In an endeavor to promote greater efficiency in the lime industry, the United States Bureau of Mines is preparing a series of preliminary reports dealing with particular problems of the industry. Through the circulation of these reports, it is hoped that sufficient interest may develop among lime-plant operators to prompt them to discuss with the bureau their our experiences with these problems. By such an interchange of ideas, it is believed that conclusion may be reached which will be of practical benefit to try entire industry. The first report, "Stripping problems it Limestone quarries of the Shenondoah Valley", Serial No. 2401, was issued during October, 1922. This report t is the second of the series. It is hoped that may operators will contribute additions to the information now at hand.]

Jan 1, 1922

By Wilbur I. Duvall

The borehole deformation gage and overcoring techniques developed by the Bureau of Mines form one of the primary methods of determining in situ rock stress. This report describes a least squares method of calculating the average rock stress components in the horizontal plane from more than three diametral deformation measurements in a vertical borehole. This least squares analysis provides a means of determining the multiple correlation coefficient, the variance, and the scatter for a set of deformation measurements. From this information, confidence limits can be calculated for the secondary horizontal principal stresses and their directions. The material presented in this report can be used as a guide to the development of least squares solutions for stress measurement techniques other than the borehole deformation method. Since the statistical information that results from the least squares method is extremely useful in the interpretation of results, it is recommended that a least squares analysis be used on stress measurement data whenever possible.

Jan 1, 1979

By P. W. Jeran

The Beckley mine is one of five new mines in a heretofore unmined portion of the Beckley coalbed. The remoteness of these new mines from prior mining and their greater overburden preclude applying methane emission experience obtained in the old mines. Four sections of the Beckley mine were monitored. The data gathered show that variations in methane emission cannot be explained by variations in coal production. Although overburdens varied by as much as 30 pct, no correlation with methane emissions could be determined. The rib emissions increase with increased length of rib from a section advancing into virgin coal and do not decline over a prolonged idle period (32 days) whereas some decline has been measured for a section not mining into virgin coal. The indication is that degasification prior to mining will reduce the hazard of methane emissions in this area of the Beckley coalbed.

Jan 1, 1977

Provide an effective method for "soft" soldering aluminum and aluminum alloys using conventional tin-lead solder alloys and flukes. The Problem In the past, it was virtually impossible to solder aluminum and aluminum alloys using standard tin-lead soldering systems (solder and flux) due to the presence of an aluminum oxide surface film which forms instantly on aluminum and aluminum alloys when these are exposed to air. The tenacious and stable oxide film enables aluminum-base materials to maintain their bright luster. But the film also prevents the required wetting and spreading of solder on the substrate, causing the loss of adhesion between the solder and the substrate. In addition, the heat produced during soldering increases

Jan 1, 1983

By W. S. Sanner

A High Splint coal was carbonized in a low-temperature, fluidized-bed sys-tem to study the effects of thermal cracking on the products of decomposition. The coal was fluidized in recycle gas at 485° to 600° C, and the products were cracked at 600°, 700°, and 800° C in a bed of fluidized coke. Yields of tar, pitch, paraffins, and olefins decreased as carbonization temperature increased. Thermal cracking of the tar vapors produced the highest tar yields at 600° C, and light oil yield increased at cracking temperatures up to 700° C. At an 800° C cracking temperature, the yield of light oil decreased.

Jan 1, 1969

By Eugene Baker, Joseph Cervik, Albert Sainato

In Europe, water infusion is used widely to reduce generation of respirable dust during mining. Its use in the United States is limited to a few plow operations in the Pocahontas No. 3 Coalbed. This Bureau of Mines report describes the technology for infusing water in to a longwall panel and reports the results of a recent demonstration in the Lower Sunnyside Coalbed that achieved dust reductions averaging 58 pct. Because water infusion increases moisture content of the coalbed, face air velocities in excess of 500 ft/min (2.5 m/s) are possible, further diluting dust levels before dust entrainment occurs. An economic analysis shows a 23-pct reduction in operating costs when coal production is increased by changing from unidirectional mining to bidirectional mining with water infusion.

Jan 1, 1983

By P. A. Bloom

Arsenic-containing flue dusts are currently being stockpiled by several nonferrous smelters in the United States. These stockpiles are a source of environmental concern since the dusts can be transported by wind and contain water-soluble arsenic. The stockpiles also represent an alternate source of metals. To provide a quality environment, the Bureau of Mines investigated a process to make environmentally acceptable the discard of arsenic obtained from the treatment of arsenical flue dust. The process includes (1) leaching arsenic from a lead smelter copper dross flue dust, (2) fixing arsenic as an insoluble compound, and (3) recovering other metal values. Overall results of acid-leaching tests on lead-smelter flue dusts showed that H2S04 dissolved 80 to 90 percent of the As, Zn, and Cd, and up to 86 percent of the In. Pb, Ag, and Au remain in the residue, which can be recycled to the smelter. Indium was recovered from the strong acid leach solution by solvent extraction; arsenic was fixed in a stable form by precipitation with Fe2(S04)3 and CaO or CaC03.

Jan 1, 1982

By Raymond M. Kacmar

This report presents the Bureau of Mines research on the hardware reliability prediction for two Bureau monitoring projects. The basic concepts of reliability predictions are introduced along with the reliability models and assumptions used for this particular evaluation. The results of the reliability predictions are for ground-fixed and naval-sheltered environments.

Jan 1, 1986

Develop rugged, cost-effective fire protection for hydraulic shovels and backhoes. Approach Automatic fire sensing and suppression systems were designed and built for use on hydraulic shovels and backhoes. How It Works A line-type temperature sensor is mounted in the machine's engine and hydraulic pump areas to detect the heat from a fire while it is still small and easy to control. Two systems were tested. In one, the inside of the sensor consists of two conductors separated by a ceramic material whose electrical resistance decreases with increases in temperature. When heated to a predetermined temperature) the control circuit responds to the resistance drop. In the second system, the detection element of the sensor is comprised of a thin metal tube containing a hydrogen charged metal hydride wire. The tube is sealed at one end and is connected to a sensitive pressure switch at the other end. When exposed to the heat from a fire, hydrogen gas released from the metal hydride wire actuates the pressure switch.

Jan 1, 1980

By H. E. Powell

The selective recovery of nickel and zinc from a waste phosphate solution by solvent extraction was investigated by the Bureau of Mines as part of a broad program to recover valuable metals and compounds from industrial wastes, and to reduce the associated land and water pollution caused by dumping these wastes. The waste, which resulted from the phosphation of automboile bodies, yielded 99 percent of both the nickel and the zinc by extraction with dinonyl naphthalene sulfonic acid (DNSA) and di-2-ethylhexyl phosphoric acid (EHPA), respectively. Dilute sulfuric acid was used to recover the metals and regenerate the solvents.

Jan 1, 1970

By J. W. Walkiewicz

One of the objectives of the Bureau of Mines is to develop substitution technology for scarce materials. In accordance with this goal, alloys containing lanthanum, cobalt, copper, and magnesium were investigated for fabrication of rare-earth-cobalt (RE-Co) permanent magnets. A complete substitution of lanthanum for samarium and a partial substitution of copper for cobalt was accomplished. Magnets of La-Co and La-Co-Cu-Mg alloys were fabricated by powder metallurgy techniques and evaluated. A maximum intrinsic coercivity of 23.2 kOe was obtained with a La-Co-Cu-Mg alloy. In comparison, maximum values of 9.3 kOe and 11.6 kOe were obtained with La-Co and La-Co-Cu alloys, respectively. The substitution of copper and magnesium for part of the cobalt resulted in a large increase of intrinsic coercivity, similar to the results of Bureau research with mischmetal-Co-Cu-Mg alloys. Unlike the mischmetal-Co-Cu-Mg magnets, the La-Co-Cu-Mg magnets showed signs of physical deterioration on exposure to air. The effects of fabrication parameters on the magnetic properties of the La-Co-Cu-Mg alloys were also determined.

Jan 1, 1982