Search Documents

Lead Tariff.--The full House Ways and Means Committee approved H.R. 6089 which will have the effect of reducing the tariff on unwrought lead to 3% ad valorem, with a floor duty of 1.0625 cents per pound, compared with the currently effective rate of 3.5% ad valorem. Consideration is also being given to tariff rates on imports of red lead and litharge from Mexico. A consortium of domestic producers has appealed to the Office of the Special Trade Representative (STR) requesting a return to tariff schedules which were in effect prior to the concessions made effective on January 1. Mexican producers have filed a proposal in favor of lower duties, and the matter now awaits a ruling by the STR. Ferrous Scrap Exports.--After holding public hearings and receiving public comments in May, the Department of Commerce announced that it would not institute formal monitoring of ferrous scrap exports, as requested by the Ferrous Scrap Consumers Coalition. The Department said, however, that it would follow the trend of scrap exports and prices. Ferrous scrap prices are currently low and supplies are reported to be adequate.

Jan 1, 1980

By J. N. Geyer

During the early stages of the mining industry of the United States an apparently inexhaustible supply of high-quality, easily accessible coal made the product cheap and the attendant mining methods wasteful of recoverable coal. Because coal from advance places could be mined with less effort and a large outwit obtained as the entries advanced, much of the coal left in pillars to support the roof was lost. Squeezes often developed in these mined-over areas, or, if pillars were of sufficient size to-prevent squeeze, the roof would be so weakened by long exposure that any pillar recovery was extremely hazardous. As the value of unmined coal increased, a high recovery of the available coal became necessary. Numerous plans were tried during the period that followed, some of the methods proving successful while others were complete failures or only partly successful. As a better knowledge was pained of the roof strata and its behavior, however, pillar mining became more successful and methods suited to special roof conditions were developed.

Jan 1, 1933

By Victor V. Verbinski

This report presents the development of a raw coal concentration sensor for hydro-transport of coal and refuse (rock) from underground mines, and the results of an international test series carried out at the Colorado School of Mines Research Institute in Golden, Colorado, the U.S. Bureau of Mines, Hydraulic Transport Research Facility in Pittsburgh, Pennsylvania, Saskatchewan Research Facility in Saskatoon, Saskatchewan, Canada, and the Steinkohlenbergbauverein Test Facility in Essen, West Germany. Test results are presented for a three-component sensor and also for the more rugged two-component (all nuclear) sensor.

Jan 1, 1988

By G. W. Jones

In a previous report,6/ results were given that showed the amount of natural ventilation in a manhole having a capacity of 74.1 cubic feet when the number of ventilation openings in the cover was varied from no openings to a maximum of 48. The result s showed that the ventilation (air changes per day) in the manhole was proportional to the area of the openings in the cover, and also that the number or area of the openings was the factor that chiefly affected the ventilation.

Jan 1, 1937

By R. F. Zaffarano

Intergrated energy balances and energy flows were constructed and quantified for State, regional, and national levels from four separate supply and demand commodity balances for coal, dry natural gas, petroleum and natural gas liquids, and utility electricity. These commodity balances were integrated by source and sectors through conversion and aggregation of their components to energy equivalents expressed in British thermal units (Btu). A summarization of the total gross energy components of supply and demand for commercial energy derived from direct fuels, hydropower and nuclear power, based on individual States and regions, is tabulated for 1960 and 1965. Pertinent computerization details and more than 500 individual State and regional printout tables, in both original commodity units and Btu's, are shown. Using these data, energy flows between States and regions were calculated to identify surplus and deficit energy areas. Report emphasis is on the conceptual aspects of integrated energy balances, rather than on the development of missing State energy data.

Jan 1, 1969

It is not uncommon to find large quantities of combustible materials in underground metal and non-metal mines. Support timber is the predominant combustible material. Spontaneous combustion, welding and cutting, shorted or overloaded electrical cables and careless smoking are common ignition sources. More recently, there is increased use of diesel mobile equipment that requires fuel storage and transfer areas. Diesel fuel spillage on hot engine manifolds and motors can result in rapid flame growth and heavy smoke accumulation in a matter of seconds. In-expensive, reliable fire detection and suppression systems are available to provide early warning of fire conditions and to isolate and extinguish fires that originate in fuel storage and transfer areas. This report presents an example of how technology developed and demonstrated under Bureau of Mines Contract H0242016, Mine Shaft Fire and Smoke Protection System, may be applied to protect underground diesel fuel storage and transfer areas. The area application described in this report is a representative example only; the fire protection described includes the concepts of ? Early warning and alarm ? Isolation ? Extinguishment ? Control

Jan 1, 2011

By Frank B. Fulkerson

Of the about 60 million pounds of aluminum used in the Pacific Northwest in 1960, 40 million pounds or two-thirds was used by 10 companies. One of these companies made airplanes and missiles; one manufactured roofing, siding, and tubing; three produced truck tractors, truck bodies, or truck trailers; two made architectural metal products; one made irrigation and industrial products; one was a general foundry; and one was a shipyard. These companies contributed to regional growth by developing markets outside the area; some have worldwide sales. Aluminum consumption increased at an average rate of 7 percent annually from 1954 to 1960. Airplane manufacture, formerly preeminent in aluminum use, no longer was in first place in 1960. By industrial group, the leading users were manufacturers of building products, 30 percent; airplanes and missiles, 22 percent; truck tractors, truck bodies, and truck trailers; 17 percent; general foundries, 5 percent; ships and boats, 4 percent; mobile homes, 4 percent; other transportation equipment, 3 percent; and irrigation equipment and all other products, 15 percent.

Jan 1, 1962

By H. S. Caldwell

The objective of this investigation by the Bureau of Mines was to develop and test for laboratory use a retort embodying many features required for practical commercial-scale applications of vacuum distillation of metals. A gas-fired vacuum retort was developed comprising a hollow, cylindrical graphite liner encased in a thin shell of stainless steel. The liner prevents the shell from collapsing under vacuum and protects it from corrosion by metal vapors and the molten metal charge. The vacuum-tight shell protects the liner from oxidation and flame erosion. The retort was used to distill zinc from dross and die-casting scrap. More than 99 percent of the zinc was recovered as a condensate containing 99.8 to 99.9 percent zinc. (Atmospheric distillation recovers 95 to 98 percent at a purity of 99.5 percent zinc.) Distillation rates of 50 pounds of zinc per hour were attained at a temperature of 65° C. with pressures ranging between 50 and 100 microns. Distillation at this low temperature is not practicable at atmospheric pressure. Also, the retort is suitable for distilling other volatile metals such as cadmium and magnesium.

Jan 1, 1961

By J. Sottile, J. L. Kohler

Component failures in the electrical control circuits of mining machines account for a large percentage of the total downtime of the machine. Once a failure has occurred it is always a tedious and usually a time-consuming task to locate the failed component. Moreover, the pressure to quickly locate the cause of a delay can lead to compromises in safety. Thus an onboard diagnostic system, essential for an automated machine, would be a very useful addition to existing machines. This report details U.S. Bureau of Mines development of a generic procedure for synthesizing diagnostic systems for electrical-control-circuit failures in mining machinery. A continuous mining machine is used as the testbed to illustrate the application of the developed methodology. Substantive differences among mining machine control circuits made it impossible to achieve a generic diagnostic system, but a generic approach for the synthesis of the diagnostic system was possible. As the research progressed, it became apparent that an algorithmic approach was better than an expert- system-based implementation. A prototype system was constructed and used to evaluate the diagnostic system. Prototype implementation issues are also examined.

Jan 1, 1993

By Christopher Mark

Perhaps the most significant development in coal mine ground control during the last century was the introduction of roof bolting during the late 1940’s and 1950’s. From an engineering standpoint, roof bolts are inherently more effective than the wood timbers they replaced. Roof bolts promised to dramatically reduce the number of roof fall accidents, which then claimed hundreds of lives each year, and they were initially hailed as “one of the great social advances of our time.” Roof bolting also emerged at a time of rapid technologic transformation of the coal industry, and greatly accelerated the transition to trackless, rubber-tired face haulage. The U.S. Bureau of Mines quickly became the new roof support’s strongest advocate. Some state agencies and miners were skeptical at first, but nearly everyone was soon won over. Case histories were reported showing that roof falls could be largely eliminated while productivity increased dramatically. Little wonder that, in the words of one contemporary observer, “roof bolting has been adopted more rapidly than any other new technology in the history of coal mine mechanization.” Yet by the end of the 1950’s, it was clear that roof fall fatality incidence rates had actually increased. It would be another decade before the superior ground support provided by roof bolts would clearly save lives. The story of how roof bolting was implemented by the mining industry, but took so long to live up to its promise, is a fascinating example of the interaction between economics, technology, regulation, and science. It still has important lessons for today.

By Reynold Q. Shotts

A study was made of the coal resources of an area in Jackson County, Ala., forming a part of the Flat Rock, Henegar, and Stevenson quadrangles. The area studied is a portion of the Plateau coalfield on Sand Mountain and is near the Tennessee Valley Authority's Widows Creek steamplant. Since no detailed geological study of this area had been published, some reconnaissance work was done. The coalbeds and adjacent strata such as sandstones, conglomeratic sandstones, and conglomerates were studied. Available drill logs, together with the areal geology, provided sufficient information to permit correlation of the coalbeds and an estimation of coal reserves. For all categories of reserves, computed on a regional basis, a total of 72,920,000 tons of coal more than 14 inches thick is estimated for the areas studied in Stevenson, Flat Rock, and Henegar quadrangles. Of this tonnage, 40,001,000 tons is estimated to have less than 60 feet of overburden. The total measured coal reserves for the above three quadrangles are 16,359,000 tons, with 12,411,000 tons under less than 60 feet of cover.

Jan 1, 1966

By W. C. Phalen

During the search for deposits of soluble potash salts in the United States, carried on by the United States Geological Survey, much infor- mation was collected on the salt resources and industry of the United States. The more important features of the information thus gath- ered, compiled, and digested may be classified under five headings, as follows: 1. Geology of the salt deposits of the United States. 2. Theories relating to the origin and formation of salt deposits. 3. Chemical composition of saline materials in the United States, principally rock salt and natural and artificial brines. 4. Statistics of salt production in the United States. 5. Technology of salt production. The first four items are not discussed in this report, but their treatment will comprise a separate report published by the Geologi- cal Survey, which will supplement this report, relating to salt- making processes, and will describe comprehensively the salt resources of the United States. Persons desiring a copy of that report should apply to the Director of the United States Geological Survey, Wash- ington, D. C. In addition to the discussion of processes, this report gives a brief description of the more important sources of salt in the United States. This description has been abstracted from the much length- ier description contained in the report to be published by the Geo- logical Survey.

Jan 1, 1917

By Gerald V. Gibbs

Quadratic functions, Q(hkl), are given to six places in increments of 0.01° for 2? from 0° to 90° for CuKa and from 25° to 180° for CuKa1. The wavelengths used for Cu in the computation are those agreed upon by the Editorial Commission of the International Tables for X-ray Crystallography (1950): CuKal 1.54051 A.; CuKa2 1.54433 A. INTRODUCTION At the Federal Bureau of Mines laboratory, Norris, Tenn., X-ray diffraction crystallography using tubes with copper targets revealed a need for a handy reference for the quadratic functions of copper radiation. The tables presented here were prepared to satisfy that need. The quadratic form Q(hkl) may be expressed in terms of the Bragg diffraction angle 2? and of the wavelength ? as

Jan 1, 1961

The accompanying supply/demand flow diagrams and 10-year tables for mineral and fuel commodities present essential data required by government, industry, and others to formulate policies and programs that can help assure an adequate and continuing supply of mineral raw materials. The 10-year data base terminates with 1973 figures because adequate world information was not available beyond that date. Moreover, 1974 was an anomalous year with respect to prices, supply, and demand for many commodities. The selected mineral supply/demand tables and flow diagrams comprise but one "output" from the massive body of "information and data collected and com-piled by the Bureau of Mines on a continuing basis covering mineral production consumption, prices, shipments, imports, exports, and stocks, as well as industry activities in all States and abroad.

Jan 1, 1975

By Gregory M. Molinda

Coalbed discontinuities historically have been hazardous to mining as well as obstructions to efficient production. An effective means of mapping these features is needed in order to plan safe and efficient mine development. This Bureau of Mines report discusses the use of surface seismic techniques for this purpose. At a southwestern Pennsylvania mine, a system of coalbed discontinu-ities (paleochannels) was accurately mapped by the Bureau of Mines using borehole log methods and underground observation. This site was chosen to test the value of a high-resolution surface seismic reflection on technique for coalbed mapping. A statistical study performed at this mine indicated that the probability of accurately delineating this paleochannel system with conventional borehole methods was remote. A total of 1.47 miles of high-resolution seismic survey, comprised of four seismic profiles, was conducted in known and suspected coalbed discontinuity areas. Several test holes were drilled on the seismic lines in order to evaluate the interpretations. It was found, based on these and other existing boreholes, that it is possible to predict these dis-continuities. Paleochannel washouts were correctly predicted in several instances but in other instances were either incorrectly predicted or not predicted in areas of known discontinuities.

Jan 1, 1988

By W. R. Reed, J. A. Organiscak

Haul trucks have the potential to generate large amounts of respirable dust. This respirable dust has been shown to be a health hazard to personnel, especially if it has a high silica content. Lack of dust sampling data from haul trucks prompted the completion of a study to quantify respirable dust concentrations. These field studies were conducted measuring instantaneous respirable dust at stationary locations from passing haul trucks at a stone quarry and at a coal mine site. Fugitive dust levels from haul trucks were analyzed to characterize dust dispersion. This analysis indicates safe following distances for haul trucks and other heavy equipment to avoid overexposure of respirable dust from the lead haul truck.

By John D. Bardill

A cooperative project between the Bureau of Mines, Department of the Interior, and the Montana School of Mines, investigating results of hydraulic systems for transporting sand slurries for emplacement, was begun in August 1955. In such circumstances, the Bureau provides funds for a fellowship leading to a Master of Science degree as well as available instruments, tools, supplies and equipment. The School provides the ore-beneficiating laboratory with its equipment for use as a pilot plant. The success of a hydraulic backfilling method employing mill tailings depends largely upon the physical characteristics of the tailings. One of these characteristics is size distribution, especially in the finer size ranges. When being emplaced underground, almost impervious layers of slimes separate from some types of mill tailings containing a high percentage of slimes and settle on the top of the sand fill. These coatings may be so dense that the water in the slurry cannot percolate through them for proper drainage. Successive layers of fill in a stope, each with an impervious coating on top, sometimes build up a hydrostatic head, creating pressure on the bulkheads. This may cause breaks in the lining material, inducing sand runs and flooding the level and sumps below. Deleterious slimes flocculated and disseminated throughout the sands should help prevent the formation of impervious slime layers, increasing percolation and settling rates.

Jan 1, 1960

By William P. Stroud

Chemical alteration of the compressive strength of sandstone has been investigated by the U.S. Bureau of Mines (USBM). Successful development of this technology would offer an attractive alternative to the methods now used for stress control in mines. Sandstone cores were stressed to failure under uniaxial compression at two different strain rates. Specimens saturated with either distilled or tap water showed an average 14% reduction in stress at failure compared with those dried in vacuum. Samples saturated with dilute solutions of aluminum chloride, hydrochloric acid, and polyethylene oxide showed no statistically significant difference in failure stress compared with those saturated with water. By contrast, compressive strength of the cores was increased some 7% by saturation with the nonpolar solvent carbon tetrachloride. No correlation was found between zeta potential and compressive strength.

Jan 1, 2010

By James L. Ash

This report contains the results of a technical and economic evaluation of conceptual systems for the underground mining, rubblization, and in situ retorting of deep oil shale deposits. Study efforts were first directed towards evaluation of the applicable geology, associated minerals, rock mechanics, in situ retorting, access mining, ventilation, rubblization, safety, and environmental impact factors. Conceptual systems were synthesized and then evaluated against these factors from both a technical and limited economic viewpoint. The results of these evaluations were then analyzed and, based upon this analysis, the following two systems were selected for further study: System II: Room and Pillar-Vertical Drill and Blast System IV: Tunnel Boring-Horizontal Ring Drill and Blast Due to the large number of variables to be considered, a computer program was developed and utilized to provide data for the cost trade-off studies and economic analysis. Results of the early computer runs indicated the value of the tool available? in the computer program and led to an extension in the contract to determine the sensitivity of the systems to several of the more apparent significant variables. These results in turn led to a refinement in the design assumptions and a better understanding of the technical and economic options available to an owner-operator of a Vertical Modified In Situ Shale Oil Extraction System. This report is submitted in fulfillment of the requirements of Contract Number 50241073 by Fenix & Scisson, Inc. to the Denver Mining Research Center, United States Department of the Interior, Bureau of Mines. Work was completed as of November, 1976.

Jan 1, 1976

By Cecil Q. Cupps

Results are presented of a comprehensive study of the characteristics of the original oil in the Weber sandstone reservoir, Rangely oil field, Colorado. Through the medium of subsurface sampling, adequately representative samples of the original reservoir oil were obtained from many parts of the reservoir over a period of 5 years concurrent with active development of the reservoir. Data of differential gas liberation, pressure-viscosity, and. pressure-volume-temperature relationships are shown for 12 subsurface oil samples. Data also are given of reservoir pressure and. temperature, composition of liberated or solution Gas, composition of 22 produced-gas samples, and Hempel analyses of crude-oil samples from 18 wells. The characteristics or physical properties of the 12 subsurface oil samples, as determined by laboratory analyses, were correlated with elevation of the top of the Weber sandstone. These relationships of oil characteristics to elevation in the reservoir show that only the oil in contact with the initial gas cap was gas-saturated at the existing pressure and temperature. The characteristics of the original reservoir oil were marked by an appreciable decrease of saturation pressure and solution gas-oil ratio and increase of viscosity and density with depth below the gas-oil contact. The composition of solution gas and of' produced was also was found to vary with elevation of the oil in the reservoir.

Jan 1, 1951