Search Documents

By G. R. Hopkins, E. M. SEELEY

According to reports received by the Bureau of Mines, Department of Commerce, as of Jamary 1, 1930, there were 1,035 natural-gasoline plants in the United States, with a total daily capacity of 10,516,000 gallons. (These data do not include one small plant in Alaska.) The last similar survey, that of Jamary 1, 1928, showed a total of 1,155 plants of 8,048,000 gallons daily capa- city. This in two years time the number of plants has decreased by 120, but the total capacity has increased 2,468,000 gallons or 31 per cent. This is roughly equivalent to the gain in production over the same periodi Over half of the increase in total capacity was registered in California, where the development of flush oil production having a comparatively high gas-oil ratio in such fields as Santa Fe Springs led to construction of some new plants and material enlargement of others. Of the total plants, 999 were operating on Jamary 1, 1930, and 36 were shut down. This compares with 1,060 operating and 95 shut down two years ago, which indicates a tendency to dismantle plants as soon as they become obsolete or umrofitable. The total daily capacity of the plants operating on Jamiary 1, 1930, amounted to 10,278,000 gallons, or 98 per cent of the total, leaving only 238,000 gallons, or 2 per cent, for the shut-down plants. This contrasts with the refining industry, which usually has 5 per cent of its total capacity idle; the difference is due to the relative ease with which a refiner can secure a crude supply as against the difficulty the natural gasoline manufacturer has in reestablishing his gas connections. During 1929 the average total daily capacity of the operating plants was 9,899,000 gallons, while the average daily production amounted to 6,015,000 gallons. This indicates that the plants operated during 1929 at 61 per cent of their capacity. Although over 60 plants were dismantled in Oklahoma during 1929 the State continued to rank first in total mumber. California was second in mumber of plants with 165, and was one of the few States that showed a gain since the

Jul 1, 1930

By Richard J. Mainiero

The Bureau of Mines has developed a prototype nonincendive explosive rock-breaker charge that can be fired unconfined in underground bituminous coal mines without the danger of igniting a flammable atmosphere that might be present. At present, unconfined shooting in underground coal mines is prohibited, but there are situations where the use of such shots would yield an overall improvement in safety. The charge consists of 1-1/2 lb of permissible water gel explosive in the form of a short cylinder 7 inches in diameter and 7/8 inches high, surrounded by a 1 1/2-inch-thick layer of damp salt, and encased in latex rubber reinforced with cheese cloth. The latex rubber housing provides a charge package that is strong enough to resist rough handling yet is pliable enough to conform to an irregular stone surface. A charge of this shape was found to be more effective at breaking rock than charges with lined or unlined cavities. Incendivity tests in a gallery have shown that the prototype charge will not ignite a flammable methane-air atmosphere when fired. Rock- breaking tests made with limestone boulders indicate that the charge will satisfactorily break stone slabs weighing 1 to 2 tons, and that two or more charges might be effective for slabs weighing up to 10 tons. In cooperation with the Mine Safety and Health Administration (MSHA), a test protocol for the certification of these charges as "permissible" for use in flammable atmospheres is being developed.

Jan 1, 1982

By R. Karl Zipf

In some instances, extensive room-and-pillar working scan collapse with little warning and pose a serious risk to underground miners. Traditional strength-based pillar design methods applicable to coal or hard-rock mines use a factor of safety defined as pillar strength divided by pillar stress. Factor of stability, defined as local mine stiffness divided by post-failure pillar stiffness, may offer a way to design room-and-pillar mines and eliminate collapses. Three alternative design approaches to decreasing the risk of large-scale catastrophic collapses are described: the containment approach, the prevention approach, and the full-extraction approach. Until good data on the post-failure behavior of pillars become available, the containment and full-extraction options are the safest. The limitations in our ability to evaluate both the stability of old workings and the long-term performance of room-and-pillar mines are described.

By Jeffery L. Kohler, Harvinder Singh, Jon G. Bredeson

A survey of electromagnetic noise reports was performed and a summary of the results are given. Industrial concerns were surveyed for techniques to minimize the effects of electromagnetic noise and are presented. The common types of communication links used in mines today are presented. A mathematical development was presented which determines the probability of bit errors versus distance for various types of communication links designed for in mine use. The probability of undetected errors for the protocols of the communication links is given together with burst error detection.

Jan 2, 1981

By W. J. Wenger

Analytical, geographical, and geological data on 67 samples of crude oils from Utah are presented, along with some correlations and interpretations. Most of the, geologic formations that produce oil in other areas are also productive in Utah; and as in many other locations, the Permian, Pennsylvanian, and Mississippian formations account for the major amount of the total oil produced in the State. Some anomalies and unusual phenomena are noted. Although most Utah oils are low in sulfur, a sample containing the highest percentage of sulfur ever recorded by the Bureau of Mines is among the oils discussed in this paper. Most of the oil from the major producing formations in Utah is low in sulfur; the same formations produce high-sulfur oils in adjoining Rocky Mountain States. Some Utah oils are both waxy and asphaltic, an unusual combination of characteristics. Correlation index curves for some oils are shown suggesting compositional differences in oils from different producing formations. Production statistics trace the rapid rise of oil production in the State after the first commercial discovery in 1947 and indicate a decline in amounts produced since 1959, the year of peak production in Utah.

Jan 1, 1971

By Charles B. Kenahan

Application of ultrasonics in the electrolytic deposition of metallic manganese and manganese dioxide from sulfate electrolytes had several effects. Ultrasonics produced finer-grained deposits of electrolytic manganese at all current densities than obtained in normal cell operation, but at high current densities it resulted in less adherent deposits. Ultrasonic radiation did not affect cell voltage or cathode current efficiency. In the electrodeposition of manganese dioxide at 70° C., ultrasonic-; increased the current efficiency and decreased the cell voltage at a current density of 9 amperes per square foot, but it had little effect at current densities above this. The decrease in cell voltage was caused by the depolarizing action of ultrasonics at both anode and cathode. Ultrasonic radiation produced a smooth, glossy, adherent, and pit-free deposit at all current densities and at each temperature. Radiation had no effect on current efficiency or cell voltage at 90° C. Ultrasonics was more effective than conventional agitation in producing all of these effects.

Jan 1, 1962

By V. C. Petersen

The titanium-rich end of the titanium-germanium system was investigated by x-ray and metallographic methods and verified by resistivity and dilatometer measurements. A constitution diagram is proposed. The titanium-rich portion of the phase diagram is characterized by eutectic and peritectic reactions. The eutectic composition is 19 percent germanium, and the eutectic temperature 1,360° C. The peritectic reaction occurs at 905° C. and 4 percent germanium. Germanium is soluble in alpha titanium to a maximum of 4 percent at 905° C. and in beta titanium to a maximum of 12.5 percent at 1,360° C. Both limits of solubility decrease with decreasing temperatures. Although substantial quantities of germanium are soluble in beta titanium, beta is not retained on quenching. The beta phase probably transforms to alpha by a martensitic reaction.

Jan 1, 1957

Minimize the effects of underground mine conveyor belt fires by developing methods to prevent automatic fire suppression system failures. The Problem Fire protection is achieved by prevention, early detection, and planned fire-fighting response. Automatic fire suppression systems are one form of planned fire-fighting response. When these systems are properly designed, installed, and maintained they can effectively control fires. Conveyor belt fires account for about 20% of underground coal mine fires. Fire protection requirements have been established for underground locations because of potential for start and spread of fire and the restricted personnel egress in a fire situation. Belt conveyor systems arc potentially dangerous because of the high fire incidence rate, high temperatures, dense smoke, toxic gases, and rapid flame-spread rate. While investigating the conveyor fire suppression problem, the Bureau identified automatic fire suppression system reliability as a potentially serious deficiency within the mining industry. Table 1 lists common failure modes fur three Fire suppression system types. This table summarizes findings of Mine Safety and Health Administration electrical inspectors responsible for inspection of belt protection automatic fire suppression systems. Batteries, contact points, control wires, and electric servocontrols are all prone to failure. Figure 1 shows rock-dust-contaminated relay contact points. This condition is dangerous because of the chance of intermittent failures, which might allow systems to pass annual functional testing, yet fail during actual fire emergencies.

Jan 1, 1989

By T. R. Strombotne

The purpose of this report k to document a contract undertaken by TSA Systems, Incorporated for the United States Bureau of Mines to develop a commercially available source of a continuous, working,, level detector for the measurement of radon daughter products in various working environments. The basic radon measuring technique was devised by Robert Droullard and Robert Holub and has been applied here. For further details or purchasing information contact: TSA Systems, Incorporated 4919 North Broadway Boulder, Colorado 80302

Jan 1, 1982

By Thomas V. Falkie, R. Venkataramani

Hand portable truck axle scales were purchased from the Martin¬Decker Company, Santa Ana, California, for weighing the rubber-tired mine shuttle cars. The scales consisted of two hydraulic load-pads, measuring 4" thick, and 21" long by 13" wide at the pad surface and one totallizer-dial indicator unit. The development of a technique to install the scales effectively for shuttle car-weighing followed an evolutionary process. The setup which finally proved to be effective entailed countersinking and level¬ling the load pads in the floor on the shuttle car trackway such that the tops of the pads were three inches below the floor level. A plat¬form consisting of two braced side-by-side 3" x 8" lumber planks was made. The platform was placed across the load pads with six inches of overlap on each side to provide room for imperfect tracking of the shuttle car. Additionally, 3" x 8" lumber planks were imbedded across the runway immediately behind and ahead of the platform. These auxili¬ary planks were firmly braced into the floor by vertical posts or jacks set against the roof; the planks constituted a stable approach platform to enable the shuttle car to roll unimpeded onto the scale platform in either direction of travel. Figure 22 shows this arrangement in detail. The setup of the scales was done during non-production hours prior to the first working shift of the week. This task took seven to twelve hours with two men. During the actual weighing experiment, the following limitations were realized. 1. Delays will be introduced into the cycle of operations because the shuttle cars must be stopped and positioned on the platform. However, these delays can be held to a minimum, time wise, as the

Jan 1, 1972

By E. C. Lane

The motor gasoline that is being marketed in the United States this winter is practically the same 'as that sold a year ago. In fact, there has been little char sin this commodity during the year, as the gasoline sold last summer was almost as volatile as that marketed last winter. Boring the past eight years, the Bureau of Mine's has made semi-annual surveys of the gasoline marketed in the United States, the survey just completed being the fifteenth in the series. The cities in which samples have been collected have been chosen as representative of the more important marketing territories as it is obviously impracticable to obtain a sample of every gasoline sold in the entire country.

Jan 1, 1927

By William P. Diamond

Ventilation has long been the primary means of controlling methane emissions in underground coal mines. However, as mining has progressed into gassier areas of U.S. coal basins, supplemental means of methane control have become of interest, if not a necessity, for continued safe and productive mining operations. This paper describes the history and technology of methane drainage in the United States and other countries. The methane drainage technology developed in European countries is a valuable resource since their longer history of mining has already forced mine operators to deal with methane emission problems only now being experienced in the United States. Methods for assessing the need for methane drainage and the data required for planning and implementing an appropriate system are reviewed. The effectiveness of the various technologies for reducing methane emissions underground and/or the in-place gas content of individual coalbeds is illustrated with case studies. In addition to the safety and productivity gains to be realized from methane drainage systems, the potential for commercialization of coalbed methane is discussed.

Jan 1, 1994

By Richard G. Burdick

This Bureau of Hines report describes an interface between a minicomputer and peripheral device, The logic used to develop the device is discussed briefly, after which the device is described in detail; complete construction and operational details are given. The report should aid both in duplicating this device and in designing similar devices for different uses.

Jan 1, 1975

By O. C. Blade

This report on the properties of motor fuels sold through service stations In the United States was made In accordance with a cooperative agreement between the American Petroleum Institute and the Bureau of Mines of the United States Department of the Interior. By agreement with the American Petroleum Institute, identification of the items Is confidential. 1t presents analytical data for 4, 802 samples, representing the products of 117 companies. The samples were collected during December 1954 and January and February 1955. As in previous surveys, the gasolines covered 6y this survey Include those from both large and small suppliers. The data were obtained by laboratories of various refiners, motor manufacturers, and chemical companies and submitted to the Bureau of Mines for compilation, A list of the National Motor-Gasoline Survey reports published during the past 10 years is given on page 5.

Jan 1, 1955

Spectrochemical methods were developed to determine beryllium in the concentration range 0.0015 to 4.0 percent in siliceous mineral beneficiation products. Two methods are described. They are (1) a fusion-pellet-spark procedure (spark method) and (2) a sustaining alternating-current arc procedure (arc method). In the spark method the sample is fused with lithium tetra-borate and vanadium pentoxide. The resulting bead is crushed, mixed with powdered graphite, and briquetted. This is analyzed spectrographically using controlled high-voltage spark excitation. In the arc method the sample is diluted with germanium metal, graphite, and vanadium pentoxide. Weighed charges are packed into cupped graphite electrodes and subjected to excitation with a sustaining alternating-current arc. Vanadium serves as internal standard for both methods. Effects due to matrix variations in samples and standards are eliminated either by fusion with lithium tetraborate in the spark method or by dilution with germanium and graphite in the arc method. Beryllium determinations show deviations from accepted chemical values of approximately 5 and 8 percent for the spark and arc methods, respectively. Analyses can be made more rapidly by the arc procedure with a sacrifice in precision and accuracy. Either method can be applied to the determination of beryllium in silicate rocks.

Jan 1, 1962

By Joe L. Castagno, Kenneth H. Johnston

Several hundred membrane - filter tests were made as part of a program to develop equipment and procedures to evaluate the quality of waters and to determine the quality of water suitable to efficiently flood oil sands of known permeability . Results indicated that neither the color of the water nor that of the precipitate on a membrane filter is a criterion for determining the quality of injection water . Reasons for poor water quality include poor operation of filtering systems , dirty filtering aggregates , excessive amounts of oil in injection water , commingling of incompatible waters , and excessive use of chemicals . A good water is required to efficiently flood sands of low permeability , but fair results may be obtained in flooding more permeable sands with poorer quality water .

Jan 1, 1964

By G. M. Potter, F. S. Wartman, M. D. Schmid

"In matte smelting of copper it has been established that the sulphpr present will combine with copper as long as the latter is present, and that thereafter it will combine with iron. The Cu-Fe ratio in the matte is determined by the Cu-S ratio, presumably owing to the much greater affinity of copper for sulphur or, expressed thermodynamically, the greater stability of copper sulphide in contact with silicate slag. Now, the work of Fournet and of Schütz, which is quoted in many elementary metallurgical texts, indicates that manganese ranks ahead of copper in its affinity for sulphur. Hence, we might expect that manganese could be concentrated from its admixture with iron. Compounds by matte smelting, and Rotts / has patented such a process. This greater affinity of manganese or sulphur is used to advantage in iron metallurgy, also, in which it is well-known that sulphur will combine with manganese and separate from metallic iron as manganese sulphide. Manganese sulphide,however, is quite soluble in silicate slags. 5/ The loss of manganese in slag in any attempted matte smelting is therefore great.If this solubility of manganese sulphide is slag is a physical one and the reaction MnO + FeS MnS + FeOIs substantially complete, then it might be expected that the addition of copper sulphide, which is almost entirety insoluble in slag, would serve to extract the manganese sulphide with the formation of a manganese-copper matte on the other hand, if an equilibrium exists in the above reaction, a copper sulphide layer would displace that equilibrium in one direction or the other, according to whether iron sulphide or manganese sulphide were more soluble in the matter layer."

May 1, 1937

By R. B. Stroud

Bureau of Mines studies of copper-bearing Permian red beds, which extend from north-central Texas through western Oklahoma to southwestern Kansas, indicate heretofore undefined commercial possibilities for low-grade, medium-volume, strip-mining operations. Potential ore bodies are indicated containing 0.5 to 1.5 percent copper in zones 6 to 12 inches thick. Cost analysis studies indicate a commercial operation is feasible for a hypothecated 1,000-ton-per-day ore mining and milling complex where a maximum of 60 feet of overburden can be stripped in mining a seam of shale 12 inches thick containing 1.2 percent copper

Jan 1, 1970

By K. Robert Dorman

This Bureau of Mines report describes laboratory and field experimentation in building mine ventilation stoppings, air-door frames, and fan bulkheads with a civil construction technique. Shotcrete is applied to a free-standing, three-dimensional wire-truss panel, which is easily cut and rapidly erected. In mines where shotcrete equipment is available, this technique should be faster and cheaper than conventional block-and-mortar or monolithic concrete construction.

Jan 1, 1980

By Alan A. Bergeron, J. L. Michels, R. L. Collins

Advanced communication and monitoring systems were developed and demonstrated in three underground mines representing different mining techniques, geographical areas, and material mined. The first mine was a large coal mine in western Pennsylvania that used room and pillar techniques and continuous mining methods. The system developed for this mine provided private telephone channels, environmental monitoring, and control of underground equipment, all on a single coaxial cable, with all system operations under the direction of a minicomputer. Many advanced features were incorporated into the system, such as paging of roving personnel, two-way section wireless, through-the-earth emergency communication, and redundant signal paths. Television was multiplexed into the system for underground equipment surveillance. A hoist radio system completed the complement of equipment at the mine. The second mine was a magnetite ore mine in eastern Pennsylvania that used block caving mining techniques. A radio system was developed that provided two-way communications between trackless vehicles and roving personnel. A unique system of uhf/vhf repeaters combined with a flleaky-feeder" transmission line offered operational and emergency features not previously found in mine communication systems. Evacuation alarming, personnel paging, fan-hole drill operator communications, and maintenance and safety vehicle dispatch were provided. The system required no dispatcher and operated during power failure. A hoist communications/shaft inspection system completed the installation. The third mine was a deep silver mine in the Cour d’Alene district of Idaho. The system developed for this mine utilizes a single wire pair to provide up to 14 voice channels. A unique combination of PBX, telephone carrier system, and intercoms offered private conversations, selective signaling, and emergency backup communications. Two hoist communication systems were installed to provide a voice link and in-cage belling signal between hoistman and cage.

Jan 11, 1981