Search Documents

By T. E. Ackman

Scale inhibitors and slow-release polymers were tested by the Bureau of Mines at mine drainage treatment facilities. The scale inhibitors were investigated to determine their effectiveness in controlling gypsum (CaSO4) scale; the polymers were investigated to determine their effectiveness for increasing settling rates of suspended iron hydroxide. Two types of scale inhibitors were tested at a site having a severe CaSO4 scaling problem. Both proved to be effective in controlling scale formation; in addition, one caused the dissolution of CaSO4 deposits. Slow-release polymers were tested at three mine drainage treatment facilities. These gelatinous polymeric flocculants were found to be convenient and easy to use, but only effective when pH could be controlled.

Jan 1, 1984

By X. B. Starnes

"INTRODUCTION The Eva Tanguay property is in Crittenden County, Kentucky, about 1 mile south or the village of Mexico, and can be reached from Marion, the County seat, by travellng south on State Highway 91 for 6.8 miles and then turning southwest on State Highway 70 and traveling 2 miles farther.Although the property lies between the Huffaw and Pigmy properties, which together have produced 200,000 tons of fluorspar ore, production from the Eva Tanguay has been estimed at only 1,000 tons. Geological factors on the property indicated the likelihood of an ore occurrence, and the author examined the property in April 1944. Shortly thereafter, the U.S. Geological Survey wrote a report on the property, which was not published. A drilling program was initiated by the Bureau of Mines November 1, 1944, and continued until eight holes totaling 3,137.5 feet were drilled.The holes showed that the Tubb fault system on the Eva Tanguay property is composed of three members, all of which contained commercial ore. The line dividing the Haffaw and Tanguay properties crosses the vein outcrops, causing a part of the ore indicated to be on each property.The mineral rights, which are leased by Robert Frazer of Marion, are owned by Mrs. O. S. Denny and W. C. Bohn, both of Marion."

May 1, 1947

By Joseph E. Matta, John C. LaScola, Fred N. Kissell

The Bureau of Mines investigated coal storage silos to determine how gassy coal must be for methane accumulations in a silo to become hazardous and where such accumulations are likely to occur. Methane concentrations were measured in the open space above the stored coal pile, in the pile, and in the reclaiming area. No methane layering was found in closed-top silos. Reclaiming areas were as gassy as the top part of the silos. Coal samples were collected from the conveyors entering the silos in order to assess the gassiness of the coal. No simple correlation was found between the gassiness of the coal stored and the measured methane concentrations. However, at mines where the average 24-hour gas emission from the conveyor belt samples was 14 ft3/ton or more, fans or open tops were used. It appears that a large fraction of the methane released during storage remains in the void space between the coal particles.

Jan 1, 1981

By G. R. Hopkins

The petroleum-refining industry established a new record in fuel efficiency at refineries in 1936, when 597,000 B. t. u. of heat were required to refine a barrel of crude oil, compared with an average of 615,000 B. t. u. in 1935 (see fig. 1). The principal factor in the "indicated gain in fuel efficiency at refineries in 1936 was an increase in crude runs of 11 percent over 1935. A large part of the heat utilized at refineries is consumed elsewhere than under stills, or in ways quite independent of crude-oil distillation. In other words, as the operating ratio (crude runs divided by capacity) for refineries increases toward the maximum of 100 percent, the fuel requirements show progressively smaller increases and the average E. t. u. consumption per barrel of crude refined declines.

Jan 1, 1938

By M. J. Dailey

This paper is one of a series being prepared by the United States Bureau of Mines on mining practices, methods, and costs in the various mining districts of the United States. The property of the Silver King Coalition Mines Co. is situated in the western past of the Park City mining district, Utah, about 1 ½ miles southwest of the town of Park City, The elevation at the collar of the main shaft is 8,137 feet above sea-level.

Jan 1, 1930

By Richard L. Unger

The U.S. Bureau of Mines has designed, fabricated, and tested a prototype track maintenance vehicle for underground coal mines. The vehicle uses a stiff rotating brush to clean the track so that a visual inspection is possible. It is also equipped to measure track gauge and cross-level. The objective of this report was to describe the track maintenance vehicle and detail the results of investigations into present underground track inspection procedures and cleaning technologies, which led to the development of the prototype. Recommendations are made concerning the integration of components of this prototype vehicle into current track cleaning and inspection systems used in underground mines.

Jan 1, 1984

By Raja V. Rarnani, Robert L. Frantz

"Mining is one of the oldest of human occupations. The awareness of occupational illnesses associated with mining, even in ancient times, is evident from the writings of Hippocrates (460-370 BC), Pliny and Elder (AD 23-79), and Galen (AD 131-210). Georgius Agricola (1494-1535), in his De Re Metallica, refers to the diseases of miners and the need for their control through good planning and operating practices and responsible management (Schwerha, 1989). Coal workers' pneumoconiosis (CWP), often called Black Lung disease, is an occupational disease which results from inhalation of coal mine dust which usually contains relatively small amounts of free crystalline silica.A pneumoconiosis is best defined as the accumulation of dust in the lungs and the tissue's reaction to its presence [Lapp and Castranova, 1993]. Silicosis is the name given to the fibrotic disease of the lungs caused by the inhalation of dust containing silicon dioxide, primarily in the free crystalline form. Silicosis is the older and more well known of these mineral pneumoconioses. In contrast, CWP was not recognized as different from silicosis until the pivotal work of Collis and Gilchrist [1928].The U.S. Bureau of Mines (USBM) still regards worker exposure to respirable aerosols in mines as the most serious health problem in mining [USBM, 1994]. The National Institute of Occupational Safety and Health (NIOSH) is considering recommending a reduction in the standard for occupational exposure to respirable coal mine dust from 2 mg/m3 to 1 mg/m3 [NIOSH, 1993]. The Mine Safety and Health Administration (MSHA) may require new criterion for sampling procedures in the mine that would evaluate the ambient dust concentration in the mine atmosphere based on a single sample, instead of the current practice of averaging five samples (MSHA, 1992; Ramat* 1993). Several high-production longwall mining faces currently have extreme difficulty meeting the existing dust standards, and some already operate at reduced production levels to achieve mandated levels [USBM, 1993]. The importance of adequately protecting the miners from high concentrations of coal mine dust, as well as of reducing the incidence and severity of the Black Lung disease, cannot be overemphasized. The importance stems, first and foremost, from the humanitarian viewpoint and, second, from the perspective of the overall welfare of the coal industry.The histopathologic hallmark of CWP is the coal macule (Balaan, Weber and Banks, 1993). Autopsy or open lung biopsy reveals the coal macule to be an amorphous mass of coal particles, dust-laden pulmonary macrophages, reticulin, and collagen. No pathognomonic signs or symptoms identify workers with CWP. A CWP diagnosis requires that the worker experienced the appropriate dust-exposure setting (e.g., underground coal mining) and duration (usually 10 years or more) and, has the characteristic chest radiograph. Based upon the International Labour Organization (ILO, 1980) international classification, pathologists and radiologists have established case definitions for characterizing the pathology and the appearance of CWP on chest radiography (Weeks, 1993). CWP appears in two principal forms: simple, with small opacities, and complicated, with opacities larger than 10 mm in diameter. For all practical purposes, diagnosis of CWP in the living miner is wholly dependent upon the chest radiograph interpretation."

Jan 1, 1995

By Martin H. Stanczyk, I. L. Feld

Continuous open - circuit attrition grinding of a coarse commercial kaolin to produce paper - coating clay , which must have a particle size analysis of 70 percent or more minus 2 - micron equivalent spherical diameter ( esd ) , was studied by the Bureau . The coarse clay , containing about 11 percent minus 2 -micron esd material , was ground in a 10 - inch- diameter attrition grinder using continuous single- and multiple - stage grinding circuits . The clay feed rates varied from 10 to 480 pounds per hour . In some tests , the influence of varying loads of sand grinding media on particle size reduction was studied . Batch grinding tests also were made for comparative purposes . Multiple- stage grinding gave better results than single - stage treatment when equivalent raw clay feed rates were used . In the best test made , a product containing about 80 percent minus 2 - micron esd material was obtained when grinding 60 pounds of raw clay per hour using a three - stage grinding circuit . Power consumption in the test was about 318 kilowatt -hours per ton of clay treated or 475 kilowatt - hours per ton of minus 2 - micron esd material produced .

Jan 1, 1963

"Research on the control of exposure to respirable contaminants in mine atmospheres is conducted in five areas; 1) control of dust generation, 2) dilution, dispersion and collection of dust in mine airways, 3) characterization of dust particles, 4) interaction of dust and lungs, 5) relationship of mine environment, geology, and seam characteristics to dust generation and mobility. The distribution of research findings to the mining industry, to government agencies, and to scientists at other universities is accomplished in several ways.A data bank of respirable dust samples displaying a wide range of characteristics (low volatile, medium volatile, high volatile, silica fireclay, rockdust) has been established by the Center. This data bank is being utilized by Center researchers in a suite of medical, scientific, and engineering tests (FIGURE 26).The Center has honored requests for educational and informational materials from several sources, including MSHA and CANMET who received information on Center generated software and used the Center's expertise in developing a computer program for particle distribution model (DISFIT).The Generic Mineral Technology Center for Respirable Dust has organized two dust conferences on respirable dust, the Coal Mine Dust Conference, held at West VirginiaUniversity, Morgantown, West Virginia from October 8-10, 1984 and Respirable Dust in the Mineral Industries: Health Effects, Characterization and Control, an international symposium on Respirable Dust in the Mineral Industries held at The Pennsylvania State University, University Park, Pennsylvania from October 14-16. 1986. These conferences were co-sponsored by the U.S. Bureau of Mines, Mine Safety and Health Administration, National Institute for Occupational Safety and Health (NIOSH), and the American Conference of Governmental Industrial Hygienists (ACGIH). On August 23-26, 1988, the VIIth International Pnuemoconioses Conference was held in Pittsburgh, Pennsylvania. While not a sponsor of this conference, researchers in the Generic Mineral Technology Center for Respirable Dust had significant participation with sixteen (16) papers presented (see Volume 8 of this series for abstracts and papers). These conferences provided a significant forum for the exchange of ideas on dust research and the interchange of research findings. The proceedings from these conferences are available from NTIS and ACGIH.In sum, significant benefits to mine worker health have resulted and should continue to result from the synergistic scientific, engineering, and medical research in respirable dust (FIGURE 27). As always, an important objective is the rapid dissemination of the results of this research to industry. Video tapes and the Bureau's Technology News series have been a very effective means of USBM technology transfer. Individual no-cost subscriptions to the Technology News series are available from the U. S. Bureau of Mines, Branch of Technology Transfer, 2401 E Street, N.W., Washington, DC, 20241."

Aug 31, 1989

By O. C. Blade

A summary of the characteristics of motor gasoline for the summer 1951 is presented in table 1, and for comparison, a similar summary for the summer 1950 is shown in table 2. Trends of some of the more important characteristics over a period of years are shown in figures 1 and 2. As indicated, octane numbers of motor gasolines sold in the United states decreased approximately one-half to one octane unit from the record levels attained during the winter of 1950-51 and are a little below the octane numbers of summer 1950. However, average vapor pressures of the summer gasolines did not change, and certain distillation temperatures varied only slightly from those of the year before.

Jan 1, 1952

By J. W. Chester

The rapid depletion of zinc-lead ore reserves and the rising costs of exploration have been major factors in the decline of mining activities and explorations for additional reserves in the Tri-State mining district. There is a need to develop new or adopt known, improved exploration techniques that will appreciably lower the costs of exploration. Demonstration of the practicability of using improved techniques to indicate, rapidly and cheaply, mineralized areas or geologic structures where more intensive explorations are justified could stimulate the search for and discovery of additional ore reserves. Various operators in the Tri-State district have used geophysical surveys to some extent since 1928 to guide exploratory drilling. Some geophysical investigations have also been made in the district by the State Geological Surveys of Kansas (11)3/ and Missouri (8, 13) and by Federal agencies (16), with the objective of directing exploratory drilling to areas where geologic conditions favored ore deposition. Many factual data obtained have not been published. The investigations generally have not been broad enough to permit conclusive evaluation of the usefulness of the geophysical techniques in all parts of the district.

Jan 1, 1959

By Maria I. De Rosa

Combustible materials, when burned, produce toxic gases and smoke, which may vary dramatically from one material to another, with resultant different total toxicity and smoke obscuration levels. This U.S. Bureau of Mines report presents smoke property data acquired for a variety of mine combustibles and shows that there exists a correlation between the smoke properties, the relative toxicity, and the smoke obscuration levels of those combustibles tested. These correlations can be used to devise simple, standard tests for determining the toxic and smoke obscuration hazards of mine materials during fire.

Jan 1, 1989

By Peter Kovalchik, Ed Kwait, T. Michael Durr

1. BACKGROUND Many research projects on engineering controls for noise reduction in mining were conducted by the former U.S. Bureau of Mines, mostly under contracts from 1972 through 1986.1 Contracts were awarded to determine which mining equipment was responsible for worker noise exposure over the permitted Federal Regulation level of 90 dBA for 8 hours. Dominate noise sources, for each piece of equipment was also determined. The final goal was to develop engineering noise controls for those pieces of equipment and then evaluate them. This was the general approach taken in each research project or contract. This paper deals with what is known about the control of noise from continuous miners, one of the most commonly used underground mining machines. A literature review on continuous miners revealed that the relevant noise sources were divided into four categories: conveyor, cutting head, drive train, and motor noise. The dominate noise sources reported were the conveyor noise and the cutting noise.2 Conveyor noise consists of impacts and scraping at various locations on the conveyor structure. These impacts are associated with discontinuities on the top and bottom decks, impacts between the chain and the tail roller, impacts on the sidewalls at path points of discontinuity under horizontal pivot, and impacts on the flex plate.3 Scraping occurs along the entire length of the chain conveyor. The other dominate source, the cutting of coal, has also been addressed in past research.4, 5, 6 The research presented in this paper only addresses the controls associated with the conveyor. The literature suggests several effective treatments for noise control: retrofitting the chain conveyor with a urethane coating or a urethane sleeve on the chain flights, using a urethane coating or urethane sleeve on the tail roller, constrained layer damping of the decks, and the use of a modified take up plate.7, 8 However, the in-mine durability of these concepts has yet to be proven for the conveyor system. This paper analyzes extensive noise and urethane durability testing on a Joy 14CM9 continuous miner’s conveyor assembly, tail roller, and bottom plate conducted at the Pittsburgh Research Lab facilities. It will also discuss the initial underground testing results for the urethane-coated conveyor flights and tail roller.

By Alla D. Mah

The energies of combustion of two carbides of tungsten and two carbides of molybdenum were measured , and the corresponding standard heats of combustion were derived . The results are as follows : WC : AH298.15 ( combustion ) = -285,940 ± 250 cal /mole , W₂ C: AH298.15 (combustion ) = -490,660 ± 400 cal /mole , Mo₂ C : AH298.15 ( combustion) = -439,350 ± 600 cal /mole , MoC : AH298.15 ( combustion ) = -269,800 ± 1,000 cal /mole . The combustion heats were combined with the heats of formation of the corresponding metal trioxides and carbon dioxide to obtain the following heats of formation : WC : AH298.15 ( formation ) = -9.6 ± 0.4 kcal /mole , WC: AH298.15 ( formation ) = -6.3 ± 0.6 kcal /mole , Mo₂ C : AH298.15 (formation) = -11.0 ± 0.7 kcal / mole , MoC : AH298.15 (formation ) = -2.4 ± 1.0 kcal /mole . The heats of combustion and formation of MoC are tentative .

Jan 1, 1963

By Michael S. Miller

In 1986 and 1987, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied the 550-acre Carson-Iceberg Wilderness Study Area (NV-030-532), in order to evaluate its identified mineral resources. The Wilderness Study Area is located in Alpine County, CA, 11 mi southeast of Markleeville, CA. Tertiary volcanic and granitic rocks, as well as alluvium, underlie the area. Hydrothermal alteration and faulting have affected some rocks; argillic, silicic, and limonitic alteration are found, particularly near faults. No mineral resources were identified in the Wilderness Study Area. The area has one small pit and no mines or claims. Samples from the Wilderness Study Area and vicinity contained uneconomic amounts of gold, silver, copper, lead, zinc, mercury, arsenic, and molybdenum. Mineral occurrences are too small and low grade to be of interest within the foreseeable future.

Jan 1, 1988

By F. H. Nehl

The U.S. Bureau of Mines investigated the selective electrowinning of Ag and Au from cyanide solutions contaminated with Cu with the goal of decreasing the amount of Cu codeposited. Decreasing Cu codeposited will reduce refinery costs. Direct current was applied to the cell in pulsed and square wave voltages at 0.070 A?h per 150 mL of solution. Times tested for each cycle ranged from 1 to 10,000 ms. Graphite, lead, and stainless steel were evaluated as electrode materials. Square wave electrowinning at 70° C gave the best separation of Ag and Au from Cu. Applying 2.5 V during the duty cycle, 0.0 V the rest of the period, a duty cycle of 10 to 30 pct, and a period of 100 to 1,000 ms gave the following results: Ag concentrations decreased from 34 to 0.1µg/mL, Au concentrations decreased from 54 to 0.2 µg/mL, and Cu concentrations remained almost constant at 560 µg/mL.

Jan 1, 2010

By James R. McVey

Tests during pillar robbing, longwall operations, and other mining activities indicate that roof-floor convergence rates can be used as an indicator of imminent roof failure. A large number of electrical-mechanical devices have been built to measure convergence as well as convergence rates, but most obstruct mine traffic and are costly and time consuming to install. The Bureau of Mines has designed and is evaluating three types of small ultrasonic units to make these measurements. The new instruments provide nonobstructing measurements up to 35 ft away. The ultrasonic transducers can be attached to a roof bolt, placed in an unsupported area (by means of a toss basket), or handheld. Total distance to the target and rate of closure are displayed digitally to 0.001 ft and 0.01 ft/min, respectively.

Jan 1, 1984

By V. F. Parry, W. S. Landers

"INTRODUCTION The primary object of this investigation was to determine changes in physical and chemical properties of subbituminous lump coal while in storage for 8 months in a typical residence and to demonstrate how this fuel may be stored without degradation or spontaneous combustion. The second object of the study was to determine how the stored coal performed in a hand-fired furnace operated under practical conditions.The investigation revealed that if care is exercised in placing sub-bituminous lump coal in a closed bin, no significant slacking or degrada¬tion occurs, no hazards arise, and over-all indicated efficiencies of about 65 to 69 percent can be obtained under practical,firing conditions that the average home owner can meet.Owing to the war emergency, much attention is being given to the proper storage of coal, and campaigns are being conducted to increase the quantity of coal being stored to relieve transportation and production overloads. Ordinarily, coal dealers do not recommend storage of subbituminous coal in homes owing to deterioration of the coal and to possible hazards from spontaneous combustion. This practice has grown from some troubles that have been experienced, which can be traced to improper preparation, improper bins, and poor technique in placing coal in a bin. There is no good reason why subbiturninous lump coal cannot be stored safely in homes."

Jun 1, 1944

By Wilbur I. Duvall, Thomas C. Atchison, Joseph M. Pugliese

Short cylindrical charges were detonated in drill holes in rock to determine the effect that decoupling ( defined as the ratio of the radius of the hole to the radius of the charge ) has on the strain - generating abilities of explosions in rock . The amplitude and period of the strain pulses produced in the rock were studied as a function of distance , size of charge , and decoupling . The main results of these studies were that , for a given distance and size of charge , the amplitude of the strain pulse decreases as decoupling increases and the period of the strain pulse decreases at first and then increases as decoupling increases . A simplified theory of decoupling is presented that satisfactorily explains the experimental results . The information presented makes it possible to predict the effect of decoupling on explosiongenerated strain pulses in rock and thus helps the explosives user evaluate the effect of decoupling on his blasting .

Jan 1, 1964

By H. B. Brunot, L. C. IlsLey

The design , construction, inspection , and test for permissibility of a storage- battery locomotive outfit in accordance with the requirements of Schedule 15* represents a large amount of work, first on the part of the locomotive manufacturer and secondly on the part of the Bureau of Mines . Detailed information of the first investigation under the schedule is presented here . This investigation covers the inspection and test of a storage- battery locomotive manufactured by the Geo . D. Whitcomb Co. , Rochelle , Ill . , to which Approval No. 1500 was assigned ,

Feb 1, 1923