Search Documents

By L. D. Wyant

[A convenient method for the, analysis of oil-wax mixtures has bean developed in the petroleum laboratory of the Bureau of Mines. This method has been found useful in studying the characteristics of the products obtained in petroleum refineries during the manufacture of ?wax distillate?, "foots oil", ?intermediate wax", and commercial paraffin. In this method ac-to-au is used as a selective solvent.]

Jan 1, 1924

By J. Pasini

The Bureau of Mines has investigated novel methods of stimulating petroleum production from reservoirs in the Appalachian Region. An important consideration in applying stimulative production methods is the control and removal of solid precipitates from the boreholes of production wells. Where paraffin-base crude oils are produced, as in the Appalachian Region, the accumulation of paraffin may be particularly troublesome. Paraffin deposition is a major production problem that has confronted the petroleum industry for many years. Although considerable effort has been expended by industry and government, a suitable solution has not been found because of the individuality and complex nature of the deposits. Remedial methods used to prevent or remove paraffin fall generally into four classes: (1) Chemical, (2) physical, (3) operative, and (4) combination. Each class has many subclasses that apply to particular problems in different oil- producing areas. Recently, chemical inhibitors and the sonic pump have assisted operators in preventing and removing paraffin deposits. Because these methods are relatively new, their degree of application has not been completely evaluated.

Jan 1, 1963

By D. B. McGilvra

This paper, describing the mining practices and methods at the Black Rock mine, is one of a series of similar papers on mining methods in the various mines of the United States being prepared by the Bureau of Mines. The Black Rock mine is located in the northeast corner of the Butte district, about 3 miles from the center of the town of Butte, and is owned and operated by the Butte & Superior Mining Co.

Jan 1, 1930

By G. W. Jones

Among its investigations into the prevention of waste in production and use of oil and gas, the Bureau of dines has made considerable study of the efficient utilization of gasoline and by-product distillates in motors, this being done chiefly by measuring and analyzing the exhaust gases therefrom. A number of reports3 of a highly practical nature have been published and are available on this subject. The results of these tests have shown that the average motor vehicle wastes approximately 30 per cent of the heat value of the fuel used, as incomplete combustion products - carbon monoxide, hydrogen, and methane, These unnecessary large heat losses are mainly due to improper carburetor adjustment, and by proper¬ly adjusting the carburetors for maximum power and efficiency a large part of this heat loss can be eliminated. This in turn results in an increased mileage per gallon of fuel used.4

Jan 1, 1924

By Kenneth R. Farley

The Bureau of Mines developed a rapid and accurate flame photometric procedure for determining cesium and rubidium in ores and in products associated with the extractive metallurgy of these elements. The effect of associated ions is neutralized by addition of buffer solution; alkali metal effects are neutralized by parallel analyses made on standard solutions similar in composition to the sample being studied. The overall accuracy of the method is within 2.5 pct of the amount of cesium or rubidium present; the range from 1 to 25 pct is the most accurate.

Jan 1, 1966

By Clarence O. Babcock

In this report, the Bureau of Mines presents a method for reducing the complexity of designing room-and-pillar mining systems by treating them as anisotropic soft inclusions in the surrounding ore or host rock. Theoretical models were derived for the calculation of the effective Young's moduli for these systems. The predicted behavior of the plate-type elements used in these models agreed well with test results from 21 plates each with 49 holes spaced on a 7 X 7 Cartesian grid. The plates behaved as anisotropic solids, the effective Young's moduli of which could be predicted from the scaled hole size and spacing. Actual hole shape was insignificant. The effective Young's moduli for simple mining systems are calculated in sample problems. This approach should provide information about field stress in the mining region and the stress distribution in the surrounding ore or host rock when the actual mining configuration is replaced by an anisotropic inclusion in a finite element analysis. The field stress within the inclusion can then be applied to the actual opening shape to determine the stress distribution within the mining region.

Jan 1, 1970

By Lloyd A. Morley

This Bureau of Mines publication presents a comprehensive review of mine electrical power-system theory and practice. It discusses fundamental theory and the vital aspects to be considered in planning and designing mine electrical power systems. The report is divided into three major sections. The first presents the history of electricity in mining and the fundamentals of electrical phenomena and components. The second focuses on power-system components: motors, grounding systems, cables, and protective equipment and devices. The final section includes mine power-center equipment, switchhouses and substations, batteries, and mine maintenance.

Jan 1, 2003

By John M. Gomes

A two-phase molten halide-silicate technique for extracting tungstic oxide (WO3) from scheelite (CaW04) and wolframite [(Fe, Mn)W04] was investigated. The halide phase extracted over 99 percent of the was, whereas the lower silicate phase retained about 90 percent of the calcium, iron, or manganese oxides. The most efficient extraction and separation of tungsten from scheelite was accomplished at 1,080° C in a molten system containing, in mole-percent, 9 calcium tungstate (CaW04), 42 sodium chloride (NaCl), 28 sodium fluoride (NaF), 17 sodium metasilicate (Na2SiO3), and 4 alumina (Al2O3). Wolframite was also treated at 1,0800°C; the molten system contained, in mole-percent, 11 (Fe, Mn)W04, 74 NaCl, and 15 Na2 SiO3.

Jan 1, 1968

By A. A. Cochran

Methods of preparing small heats of steel containing radioisotopes were developed, and the techniques of stripping film autoradiography were used to detect and study the carbide and sulfide phases in titanium-bearing steels. Metallography had revealed areas of titanium sulfide and ferrite or pearlite adjacent to areas of titanium carbide and ferrite, and unidentified, irregular phases at the boundaries between these two areas. Sulfur 35 was used to deter-mine the extent of the titanium sulfide inclusions, and carbon 14 was used to delineate the titanium carbide phase. Individual radioactive areas were located with a resolution of approximately 10 microns. A general background exposure that was not correlated with microscopically visible phases was observed in the carbon 14 autoradiographs. The evidence from both sulfur 35 autoradiographs and carbon 14 autoradiographs indicated that the unidentified inclusions were sulfides rather than carbides. INTRODUCTION The use of radioisotopes to facilitate the work at the Rolla Metallurgy Research Center was expanded in fiscal year 1959 when the Bureau of Mines authorized the installation of an intermediate-level radioactivity laboratory. Before this time, sealed cobalt 60 sources had been employed for radiography, but no tracer work was done. The primary objective of the first experiments conducted in the new laboratory was to supplement physical metallurgy investigations of selected problems in steel research.

Jan 1, 1962

By L. B. Pankratz

The Bureau of Mines measured heat capacities of alpha and beta spodumene (LiAlSi2O5) and of beta eucryptite (LiAlSiO4) over the temperature range 51° to 298° K. The entropies at 298° K were found to be 30.9 ± 0.2 cal/deg mole for alpha spodumene, 36.9 ± 0.3 cal/deg mole for beta spodumene, and 24.8±0.2 cal/deg mole for beta eucryptite. High-temperature heat content measurements above 298° K were conducted for the same compounds. Measurements were made to 1,150° K for alpha spodumene, 1,600° K for beta spodumene, and 1,470° K for beta eucryptite. Tables of heats and free energies of formation are given from the elements and from the constituent oxides.

Jan 1, 1967

By Leon W. Dupuy

Marquette's first reported the existence of iron In Missouri in 1673. Recorded production wan begun in 1815, increasing in size and importance until 1888, when the low price of iron resulting from Minnesota's production of high-grade ore caused most of the operators to close down. Missouri's iron production came from three types of ore: (l) Brown ores, including the deposits of primary and secondary limonites in southeast and southwest Missouri, (2) hematites of the filled sinks, including the ores of Central Ozark district, and (3) specular ores in porphyry, including the deposits of the St. Francois Mountains.

Jan 1, 1949

By J. A. Woolf, E. S. Leaver, N. K. Karchmer

"In the cyanidation of silver ore, the need of oxygen is well recognized. Various methods have been introduced for supplying the oxygen. In usual practice, air is the source of oxygen and the methods of application are mechanical.This article gives the results of touts made to show the rate of dissolution of silver from each of the common silver minerals in cyanide solution, under conditions similar to those used in the practical recovery of silver from its ores. The effect of oxygen in aiding the dissolution of the silver from each mineral is also shown by a comparison of the methods of supplying the oxygen. Oxidation by preliminary roasting (500°C.) of each mineral sample gives the maximum extraction of the silver by treatment with cyanide.Each silver mineral5 used in these experiments was as pure as could be obtained from the mineral dealer. In their natural occurrence, silver minerals are not usually free from mineral impurities. They are usually closely associated with other minerals often forming, a complex mixture. The form of crystallization, the proportions, and properties of the diluent that incases or has been dispersed with the silver mineral may decidedly affect the dissolution rate of the silver from each mineral. While the following results should aid in the cyanidation of silver ores, each ore should be studied from the basis of the form and condition of the silver that is to be recovered.All the tests reported in this article were made on synthetic samples, prepared by mixing the particular silver mineral with clean sea sand. Each mineral was ground in an agate mortar to pass 100-mesh before mixing with the sand which had previously been ground in a porcelain pebble mill to 100-mesh. Such proportions of each mineral and the sand were used as to give a head assay of approximately 20 ounces of silver per ton to the synthetic sample.Agitation was carried on in stoppered bottles approximately one-third full of pulp, method apparently supplied all the atmospheric oxygen that would be taken up by the solution under usual conditions, because tests conducted in open bottles did not show increased recovery,"

Jan 1, 1931

By D. S. Burgess

An investigation of the hazard of spillage of liquefied natural gas (LNG) onto water is described. About 2,000 gallons of LNG were consumed in various tests. The initial vaporization rate of LNG following spillage was found to be 0.037 lb/ft2 sec; when the spill was confined, this vaporization rate was moderated after about 20 seconds by the growth of an ice layer on the water surface; when the spill was unconfined, a coherent ice floe was not observed and the vaporization rate was essentially time independent. The maximum diameter (in feet) of the spreading LNG pool was found to be given by 6.25 Wo 1/3, where Wo is the weight of LNG in pounds, Downwind of a natural gas source, time-averaged methane concentrations were given in good approximation by standard air pollution equations. However, peak concentrations were as much as twentyfold higher than average, adding an additional factor to the assessment of hazard. The effect of layering by the cold vaporized natural gas was similar to the effect of a temperature inversion on normal gases in the atmosphere. Small-scale explosions were observed on pouring LNG onto a water surface; no single explanation seems pertinent to all of the incidents observed.

Jan 1, 1970

By H. R. Appell

The Bureau of Mines studied the conversion of a variety of cellulosic wastes, for example, sawdust, bovine manure, sewage sludge, urban refuse (free of metal and ceramics), etc., to heavy oils. The objective of the investigation was to determine the scope of the reaction and elucidate the chemistry involved. The reactions took place in the presence of synthesis gas and water or carbon monoxide and water under conditions of elevated temperatures and pressures. Waste conversions above 90 pct, often near 99 pct, with oil yields in the range of 40 to 60 pct, were obtained in the temperature range of 250° to 425° C and pressure range of 1,500 to 4,000 psig. Because mild conditions were sought, most of the experiments were conducted at temperatures of 250° to 350° C and pressures of 1,500 to 3,000 psig. In general, lower viscosity products were obtained at higher reaction temperatures. Conversions and oil yields were significantly increased by operating in the presence of a high-boiling oil; either anthracene oil or oil recycled from the process was satisfactory. Synthesis gas containing 50 pct carbon monoxide gave satisfactory results as a replacement for carbon monoxide. Cobalt molybdate on alumina catalyst, used with sodium carbonate, gave a product of lower viscosity and lower oxygen content than sodium carbonate used as the sole catalyst. The waste-to-oil process has been successfully investigated in continuous flow equipment as well as in batch autoclaves.

Jan 1, 1975

By H. G. Iverson

Solid state reactions of manganese with silica were investigated in high-temperature tests. Reactions of 0.5 to 4.0 moles manganese (Mn) with 1 mole silica (SiO2) at 1,100° C and of 2.0 Mn:SiO2 mole-ratio mixtures at 1,000° to 1,150° C yielded products consisting of a slag phase and a metallic phase. At 1,100° C, the slag phase from reactions of the low Mn:SiO2 mole-ratio mixtures was composed of SiO2 and rhodonite (MnSiO3), and the slag phase from the high Mn:SiO2 mixtures was composed of MnSiOs and tephroite (Mn2SiO4). The metallic phase from the corresponding low Mn:SiO2 mole-ratio reactants consisted of two manganese silicides, Mn5Si3 and Mn3Si; from the high Mn:SiOg mixtures, it was Mn and the manganese silicide (Mn5Si). For the higher mole ratios of MnSiO2 the manganese content in the metallic phase increased, while the manganese and silica contents of the slag phase remained nearly constant. The slags did not contain free or uncombined manganese oxide (MuO). For the 2.5 to 4.0 Mn:SiO2 mole-ratio mixtures reacted at 1,100° C, the maximum quantities of silica reduced and of the manganese in the slag appeared to become asymptotical at about 41 and 48 percent, respectively. A brominating procedure was developed that was highly selective in removing the metallic constituents from the reaction product, leaving the slag phase as residue. X-ray diffraction patterns were obtained on prepared silicides Mn5Si, Mn3Si, and MnSi.

Jan 1, 1967

By P. C. Tully

The vapor pressure-temperature relationships for saturated pure liquid nitrogen are calculated by the Strobridge equation using a digital computer. This information is presented in two tables: first) in pressure increments of 0.1 psi from 1.8 to 492.9 psia) and second) in temperature increments of 0.1° from 63.15° to 126.26° K. These tables should facilitate the calibration of temperature-measuring devices over this temperature range.

Jan 1, 1967

By James H. Gary

Data regarding the composition and physical properties of Florida land-pebble phosphate-waste slime are presented, and the feasibility of dewatering and beneficiating the slime by several different methods is discussed. Chemical analyses, electron micrographs, and X-ray diffraction data showed that principal constituents of the slime included quartz, attapulgite, and flaorapatite. Viscosity of the slime changed with pH; thixotropic, Newtonian, and rheopectic states were observed as the pH increased. Use of various flocculating agents was not effective in improving thickening properties of the slime. Dewatering tests using pressure filtration showed that temperature influenced the filtration rate more than pressure; the filtration rate at 165° C was tenfold that at room temperature. Selective flotation of the slime, using two different processes, gave promising results. About 25 pct of the phosphate was recovered in a concentrate assaying 31 pct P205, Other tests demonstrated that the slime could be successfully fractionated at 20-microns using a hydrocyclone. In hydrometallurgical tests about 80 pct of the phosphorus and alumina were chemically extracted from the slime using sulfuric acid. Limited bacteriological studies made of the slime showed that several types of microorganisms were present and grew in the material despite the presence of fluorine-bearing minerals.

Jan 1, 1963

By Khamis Y. Haramy

This U.S. Bureau of Mines report describes the use of Bureau-developed flat and cylindrical hydraulic borehole pressure cells. A brief description of the fabrication, installation, and pressurizing equipment is given and pressurizing procedures are discussed. Theories available on evaluation of data from the flat and cylindrical pressure cells and examples of data analysis and stress evaluation are also presented.

Jan 1, 1991

By William C. Smith

Roof support, an important aspect of ground control, involves maintaining roof competency to ensure a safe and efficient mining environment. Wide variability in rock quality and stress distributions requires a systematic approach to roof support design that satisfies specific goals. The success of past roof sup-port in reducing the incidence of roof falls has been primarily attributed to safer roof bolting practices. However, roof falls continue to be the number one occupational hazard in underground coal mines. This U.S. Bureau of Mines report presents a general overview of roof bolting and other roof support methods used in the United States. Characteristics of bad roof and associated roof failure theories are briefly presented as background to roof support. Methods of detecting and monitoring roof behavior and/or bolt performance provide essential feedback on roof support requirements. A discussion follows on roof bolt design that assimilates roof and support parameters into useful equations or nomographs to help decide what bolt types to use and how they should be installed under different roof conditions.

Jan 1, 1993

By R. W. Van Dolah

The Bureau of Mines t.ced its investigations into sympathetic detonation of ammonium nitrate (AN) and ammonium nitrate-fuel oil (AN-FO) to define the scaling law for safe separation from detonating AN-FO. Both missile- and non-missile-producing AN-FO donors, weighing up to 5,400 pounds, were employed with acceptors of the same size. The usual cube-root scaling law was not confirmed; exponents for the relationship S = f(Wx) for AN were 0.51 with non¬missile-producing donors and 0.61 for missile-producing donors. For AN-FO an exponent of 0.80 was indicated in the missile-producing case. AN-F0 in polyethylene bags appeared somewhat more easily initiated than bulk AN-FO. The efficacy of barricades in protecting AN charges was investigated. detonation distances were reduced from one-third to one-seventh when filled barricades were employed. The investigation was extended to dynamite with both types of donors. With 1,600-pound missile-producing donors and an equivalent weight of dynamite, initiation would be expected in 50 percent of the trials at 167 feet. The corresponding value in the non-missile case was 67 feet. The data developed in this program of sympathetic detonation will allow the development of a rational set of safe separation distances for AN, AN-FO, and explosives.

Jan 1, 1966