Search Documents

[ ]

Jan 1, 2011

By James C. Cawley

The Bureau of Mines conducted an investigation to statistically determine the mean current or voltage for resistive, inductive, and capaci-tive circuits that would cause spark ignitions in 8.3% methane-air, 5.3% propane-air, and 7.8% ethylene-air mixtures. Each mean ignition current or voltage was determined on the basis of 100 trials. Each trial consisted of 400 revolutions, 200 in each polarity, at 80 rpm of the standard breakf1ash apparatus. In general, spark ignition curves published in UL 913 for resistive and inductive circuits represent approximately the mean current values determined in this study, while published capacitive circuit values in methane are considerably less than the mean voltage values from this study, especially for a capacitance of less than 100 ~F. For resistive and inductive circuits, spark ignitions were obtained at currents con-siderably below those in the published curves, but this study was not optimized to find minimum ignition values. This report defines "safety factor" as applied to intrinsic safety testing as the energy ratio of the mean values of ignition current or voltage for two test gases. The safety factors presented in this report are not constant with voltage or current and, therefore, are not recommended for use.

Jan 1, 1986

This is the first publication in a projected series of reports on properties of commercial motor fuels pursuant to a cooperative agreement between the Cooperative Fuel Research (C.F.R.) Committee and the Bureau of Mines of the Department of the Interior. The report gives results of analyses in oil-company laboratories of sample of gasoline obtained from service-station pumps in 18 marketing areas by representatives of oil companies. These companies obtained the samples and analyzed them for their own information and supplied data from their laboratory reports to the Bureau of Mines for compilation and publication. History of Bureau of Mines Gasoline Surveys The following quotation from Report of Investigations 31624/ is included in this place for the information of readers who are not familiar with the Bureau of Mines gasoline surveys that have preceded the present report:

Jan 1, 1936

By Martin H. Stanczyk

The Bureau of Mines studied continuous closed-circuit attrition grinding of a coarse commercial filler-grade kaolin to produce paper-coating-grade clay having a particle size analysis of at least 70 percent minus 2-micron equivalent spherical diameter (esd). The coarse clay, containing about 12 percent minus 2-micron-esd material, was ground in a Bureau-developed 10-inch-diameter attrition grinder in closed circuit with a 5-foot-diameter bowl classifier. In the best test, a finished product containing 82.7 percent minus 2-micron-esd material was obtained when grinding 20 pounds of raw clay per hour at percent solids with a 100-percent circulating load. Energy consumption was about 341 kilowatt-hours per ton of clay feed, or 487 kilowatt-hours per ton of minus 2-micron-esd material produced. Closed-circuit grinding gave some-what greater particle size reduction and lower energy consumption than either batch or continuous open-circuit grinding.

Jan 1, 1965

By R. J. Matetic

The Bureau of Mines, as part of a program to improve mine planning and development, is currently investigating the effects of pillar load transfer, which can impact mining operations within a multiple-seam configuration. A comparative study was performed at two separate mine sites. The objective of this study was to compare two mines, each affected by this pillar load transfer mechanism, and to show how this interaction affected underground workings by the installing and monitoring underground instrumentation. At mine site A where the overburden was 1,000 ft, the innerburden thickness was less than a pillar width (40 to 45 ft), overlays of the mine layout show pillars were not superpositioned, excessive roof to floor convergence was measured, and pressure readings indicated pillar core loading only. At mine site B, the overburden was approximately 555 ft, the innerburden thickness was approximately 105 ft, overlays of the mine layout show pillars were superpositioned, minimal roof to floor convergence was measured, and pressure readings indicated a skin loading only.

Jan 1, 1988

By J. L. Reuss

The Bureau of Mines investigated the technical feasibility of smelting copper concentrates containing chalcocite (Cu2S) and native copper using nonpyritic sulfur-bearing materials to aid matte formation. The procedure consisted of combining various proportions of commercial chalcocite concentrate, smelter slag, fluxes, and matte-forming constituents to produce charges of comparable compositions. The mixtures were charged in fire-clay crucibles and smelted in an induction furnace at 1,300° C. The research proved that either sulfur or gypsum can replace pyrite as a matte-forming material, and that gypsum produces an exceptionally high-grade copper matte. The addition of small quantities of metallic iron to the nonpyritic smelting charge furthers the removal of sulfur, improves the recovery of copper, and makes it possible to utilize gypsum as the exclusive flux and matte-forming ingredient, thereby eliminating the necessity of adding limestone.

Jan 1, 1968

By Lloyd A. Morley

This Bureau of Mines publication presents a comprehensive review of mine electrical power-system theory and practice. It discusses fundamental theory and the vital aspects to be considered in planning and designing mine electrical power systems. The report is divided into three major sections. The first presents the history of electricity in mining and the fundamentals of electrical phenomena and components. The second focuses on power-system components: motors, grounding systems, cables, and protective equipment and devices. The final section includes mine power-center equipment, switchhouses and substations, batteries, and mine maintenance.

Jan 1, 2003

By R. V. Higgins

Tarner (1),3/ Muskat (2), and Schilthuis (1) have presented methods of calculating oil recovery by the expansion of dissolved gas with and without return of gas to the reservoir. Although electronic computers have eliminated the tedious and time-consuming calculations (4) required by each of these methods, many petroleum engineers do not have access to electronic computers. For these engineers a short method is presented that uses the Tarner method as a base. Moreover, for engineers who have access to computers and have not as yet prepared a program, the short Tamer method requires less computer time than the long iterative methods. In the proposed short method, no plotting of the calculated data is required to determine a point of intersection described in the original Tarner presentation, as only one calculation is needed to determine the value sought, or two calculations if greater accuracy is desired.

Jan 1, 1960

By D. Bienstock

In connection with air-pollution studies, the Bureau of Mines is cooperating with the U.S. Public Health Service in investigating the use of solids for removing sulfur dioxide in concentrations of less than 0.5 percent from combustion and waste gases. Removal of sulfur dioxide at flue-gas tempera¬tures would no longer result in the cooling of scrubbed gas, which is inherent to liquid scrubbing processes used exclusively in industry today. Results are reported of extensive investigation, using metallic oxides as absorbents, adsorbents, and oxidation catalysts at 130° and 330° C. (temperatures at which flue gas may be treated in powerplant practice). The most active absorbents tested were the oxides of manganese, cobalt, copper, and alkalized alumina; 23 to 33 grams of sulfur dioxidn were removed by 100 grams of absorbent at 130° C., while scrubbing more than 90 percent of the sulfur dioxide from a simulated flue gas, and 19 to 61 grams of sulfur dioxide were removed at 330° C. A more detailed study is reported on absorption and regeneration, using manganese oxides and alkalized alumina. Adsorption of sulfur dioxide on activated carbons and molecular sieves at elevated temperatures is considerably less efficient than removal by absorption--a maximum of 7 to 8 grams of sulfur dioxide could be removed with 100 grams of adsorbent at 130° C. A potash-promoted vanadium pentoxide is effective in converting sulfur dioxide to trioxide; complete conversion in a simulated flue gas containing 0.35 percent sulfur dioxide was obtained at 365° C. Pilot-plant and cost studies are being made by the Bureau to determine the economic feasibility of removing on an industrial scale the sulfur dioxide present in gases in low concentrations.

Jan 1, 1961

By Richard L. Fischer

Constant-volume charges of precipitated PETN (pentaeythrite tetranitrate) at three specific gravities (0.50, 1.00, and 1.50) were used in laboratory tests to examine the effects of changes in explosive properties on free-surface displacement pulses and on crater dimensions. The tests were performed in large blocks of cement-mortar. The values for the detonation velocity, detonation pressure, specific energy, energy density, and energy release rate were calculated from the explosive loading density. Calculated explosive properties were correlated with free-surface displacement pulse measurements, strain energy, and measured crater dimensions. Increases in explosive properties resulted in increased free-surface displacement pulse parameters and crater dimensions. The loading density, detonation velocity, energy density, detonation pressure, and energy release rate were found to be best indicators of explosive performance. Simple acoustic relationships involving impedance ratios were examined and could not be used to predict peak displacement amplitude or strain energy. Data are presented in the customary English units as well as the International System of Units (SI).

Jan 1, 1970

By Lathrop E. Roberts

The opinion is general among smelter operators that magnetite formed in the converter and reverberatory furnace has much to do with the loss of copper in the slag. Its action appears to be due in part to its relatively high infusibility, chemical stability, and specific gravity, as a result of Which it tends to form a layer of highly viscous "magnetite mush" between slag and matte. Particles of matte which might otherwise settle out of the slag are unable to pass through this layer. Maier and Van Arsdele have shown that the inclusion of grills of matte in the slag is also at tires very probably due to chemical reaction between magnetite and the constituents of the matte. In smelter control and in any laboratory study of slats the determination of magnetite is therefore a matter of some importance. The difficulties in the ray of making such a determination with any accuracy are rather obvious. Iron may occur in slag as ferric oxide, magnetite, various intermediate oxides, sulphides, silicates, as free metal, and in solid solution of several of these substances. Even if only the total iron content is to be determined, accuracy can be obtained only by painstaking and time-consuming separations from interfering elements. The determination of ferrous, ferric, and free iron in the presence of each other is a difficult matter under the most favorable conditions, and when present in a slag the difficulties are increased by the refractory nature of the sample, by the presence of sulphides, and by such elements as vanadium and molybdenum.

Jan 1, 1931

By C. I. Pierce

The Bureau of Mines used an electrolytic tank model to investigate the response of guard electrodes of different dimensions under different simulated reservoir conditions. Sandstone disks from the Berea and Connellsville Formations were used as resistive beds in the model, and agar gel or water was used as conductive beds. In the experiments, bed thickness, hole diameter, mud resistivity, and bed resistivity were varied. The guard electrode is an excellent tool for determining true bed resistivity in the thin-bedded oil reservoirs of the Appalachian area. Vertical resolution and resistivity values are good when there is little or no invasion. Resistivity values are near true bed resistivity in beds thicker than about six hole diameters when the electrode-to-hole-diameter ratio is close to 1. However, low-resistivity muds cause false peaks to appear on the logs near bed boundaries in thick beds, and for resistive beds having a thickness approximately three to five times the hole diameter, apparent resistivities tend to be excessively high when mud resistivity is low.

Jan 1, 1966

By T. F. Mitchell

During the investigation or the occurrence of manganese deposits in western United States, Bureau of Mines' examining engineers collected samples from four manganese properties in the Death Valley region, California. These were supplemented by samples submitted by owners of two other properties in the same area. Extensive laboratory tests were made to determine the, amenability of the ores to standard ore-dressing concentration methods. A small sample of high-grade oxide manganese ore from the McWhinney property, San Bernardino County, Calif., was submitted by the owner. Although the sample would sinter directly to plus 48 percent manganese grade, it appeared probable that the ore, if mined in quantity, would be lower in grade and would require beneficiation. Therefore, testing was conducted to remove the chief gangue constituent, calcite. The National Resources, Inc., property (also known as the old Owl Hole mine) is in the Owl Hole Springs district, I mile from Owl Hole Springs, San Bernardino County, Calif., near the southwest corner of Death Valley National Monument. The ore deposits occur as small lenses or ,pockets, evidently .replacements in limestone and granite. Laboratory work was done on a representative sample of orb procured by Bureau engineers.

Jan 1, 1949

By Francis Church Lincoln, Paul Zinner

"Attention of the Bureau of Mines was first directed to the Gray farm area by the results of several exploratory churn-drill holes completed by the New Jersey Zinc Co., and later by Roland J. Teske and by Judge H. L. Heer.When the Bureau of Mines initiated its investigation of the area, all drilling on the Gray farm had been discontinued, and no mining had resulted from the exploratory work. However, in the opinion of the Illinois Geological Survey, the Federal Geological Survey, and the Federal Bureau of Mines, this drilling,with the preliminary geological studies, was considered sufficient evidence to justify continued exploration to the southeast along a projection of the trend of mineralization developed in the mines to the northwest, or the so-called Black Jack Trough.This report describes the work done and presents the data obtained during the period of Bureau of Mines exploratory work.In its program of exploration of mineral deposits, the Bureau of Mines has as its Primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report. The Metallurgical Branch, R. G. Knickerbocker, chief, analyzes samples and performs beneficiation tests. Both these branches are under the supervision or Dr. R. S. Dean, assistant director.Special acknowledgment is due Paul Herbert, geologist, Illinois Geological Survey, for his studies of cores, which greatly influenced the planning and progress of the exploratory work. Acknowledgment is also made to A. F. Agnew and A. V. Heyl, geologists, Federal Geological Survey, for their invaluable aid; to 0. W. Terry, F. C. Lincoln, M. H. Berliner, A. M. Cummings, project engineers; and to E. P. Barrett, district engineer, Minneapolis, and E. D. Gardner, regional engineer, Rolla, Mo., for supervising the program.The Gray ore body is on the Gray farm 5 miles south of Galena in Jo Daviess County, northwestern Illinois. The location with respect to adjoining properties is shown on figure 1. Galena is a city of 4,000 population on the banks of the Galena River, a stream that was formerly navigable by Mississippi River steamers but has now shrunk to the dimensions of a small creek. A gravel road leads from the city to the Gray farm and onward to the Bautsch and Boevers farms to the south of it."

Sep 1, 1946

By H. F. Yancey

Although a general relationship exists between the two criteria used to measure sharpness of separation -error area and probable error -they sometimes give quite different appraisals of a particular washing operation. Error area takes into account how the entire raw coal was treated, whereas probable error reflects only how the material of intermediate density was separated, ignoring completely the recovery of clean coal and the rejection of heavy impurity. Error area is thus more reliable for general use. In heavy-medium cleaning, sharpness of separation decreases with increase in separating density, but ordinarily the change is not great enough to affect the yield and ash content of washed coal measurably. Therefore, distribution curves for heavy-medium units can be transposed from one separating density to another, at least in the range of separating densities ordinarily used in the United States.

Jan 1, 1955

By D. E. Fogelson

In a factorial experiment, blasting caps were detonated in three sizes of shotholes in mortar with three types of stemming--dry sand, wet sand, and hydrostone. Free-surface displacement pulses were recorded with a capacitive-displacement gage at a distance of 15 inches. The effects of decoupling and the type of stemming on the amplitude and the duration of the displacement pulse were determined. Both the amplitude and the duration of the displacement pulse were significantly decreased by increasing the decoupling, but they were little affected by the type of stemming.

Jan 1, 1965

By D. Harrington

Fire is always a serious-menace, whether in a residential or in an industrial region; in wartime it is particularly damaging in an industrial plant. The mining industry is especially vulnerable, as its plants are generally more or less isolated front centers of population and do not have access to modern fire-fighting equipment; moreover, owing to the transitory rapture of most mines, their surface structures; are often relatively flimsy and flammable.. Trained firemen seldom are available at or near mining plants to teach the fundamentals of fire-fighting to local fire brigades, with the result that efficiency in combating actual fires is lacking. Often the attitude "it can't happen here" is held by the management of a mining property, unless the plant has suffered a serious fire; even then lapse of time is very likely to induce forgetfulness as to the possible hazards. The necessity for producing metals for the prosecution of this war has increased management's responsibility. Whereas heretofore the loss of a plant or mill by fire meant merely monetary less to the stockholder of the company, now the national interest is affected, in that the nation suffers from loss of production of minerals indispensable for war purposes.

Jan 1, 1943

By R. V. Ramani, K. Bode

"IntroductionThe theory of particle dispersion and deposition in turbulent flow is important to many fields of science and engineering. Dispersion has been studied in some detail since the early fifties (Taylor, 1954; Fischer, 1967; Osipov and Grekov, 1968; Skobunov, 1970 and 1973; Klebanov and Martynyuk, 1974). A broad research effort has also been underway in studying the mechanics of dry particle deposition. Friedlander and Johnstone (1957) proposed a theory, according to which particle deposition from vertical pipe flow could be described by an eddy diffusion transport followed by a final flight to the surface. There have been numerous revisions and additions to this original theory (Owen, 1960; Liu and Agarwal, 1974; Liu and llori, 1974; El-Shobokshy and Ismael, 1980) The mining process essentially consists of breaking in situ materials and transporting them out of the mine. An inherent characteristic of this process is the generation of fine particles. Fine airborne particulates are associated with a number of threats to the health of the miners; fine coal dust can also result in mine-wide catastrophic incidents such as dust explosions. For these and other reasons, it is important to understand the behaviour of airborne dust particulates, particularly their generation, entrainment, transport, dispersion, and deposition in the mine environment for their control.Mine related studies on dispersion and deposition have been few. Yet, several studies of gas and dust dispersion, diesel exhaust contamination, and methane ingress into mine workings have recognized the need for developing reliable parameter values for fundamental understanding of the phenomena (Da""Yes and Slack, 1954; Hodkinson, 1957; Hodkinson and leach, 1958; Mass and Wildschut, 1966; Airey, 1969; Courtney et al., 1986; Stefanko, Ramani, and Thakur, 1974; Stefanko, Ramani and Kenzy, 1977; Bhaskar, 1987, Bhaskar and Ramani 1990; Qin and Ramani, 1989; Shankar and Ramani, 1990)."

Dec 1, 1995

By John W. Kopp

A major concern with blasting at surface mines is generation of ground vibrations and airblast and their effects on nearby residences. This Bureau of Mines report looks at the use of millisecond delays in blast design and their effect on the resulting ground vibrations and airblast. A total of 52 production blasts were instrumented and monitored at a surface coal mine in southern Indiana. Arrays of seismographs were used to gather time histories of vibrations and airblast. The data were analyzed for peak values of vibration and airblast and for frequency con-tent. Various delay intervals were used within and between rows of blastholes. Delay intervals within rows were 17 and 42 ms, and those between rows ranged from 30 to 100 msj these intervals are equivalent to 0.5 and 1.3 ms/ft within rows and 1.2 to 4.3 ms/ft between rows. Sub-sonic delay intervals within rows reduced airblast by 6 dB. Large delay intervals between rows reduced the amplitude of ground vibrations; their frequency depended primarily upon the geology of the mine site.

Jan 1, 1986

By H. Kim, R. W. Plummer, T. J. Stobbe

"The probability of developing coal workers' pneumoconiosis (CWP) varies among miners in different geographic areas, coal seams, and jobs. Many studies have revealed the correlation between mineral content and the frequency and severity of CWP development still remains controversial. Furthermore, the mineral content and its variability in different areas is unknown.Since mineral content is expected to vary from location to location within a mine, between mines, between coal seams, and over time, this information will be valuable in understanding the variations in CWP incidence, as well as in establishing the appropriate kinds of dust to use in toxicological research programs studying CWP.Size-selective airborne dust samples were collected using 4-stage cassette impactors at 9 different locations in each of five coal seams. These coal seams were the Upper Freeport, Pittsburgh, Kittaning, Coal Burg, and Pocahontas. Mineralogical analyses were done by a x-ray powder diffraction photographic technique.Common minerals found in coal mine dust were illite, calcite, kaolinite, quartz, siderite, dolomite, gypsum, anhydrite, and pyrite. The distribution of minerals in interand intra location samples will be reported. Early results on the mineral content show wide variations between locations.in a mine and between coal seams, and small, but significant, variations between particle sizes.INTRODUCTIONIn spite of its long history of incidence, and the large amount of research conducted on it, coal workers' pneumoconiosis (CWP) is still prevalent among coal miners and needs further research to develop effective preventive and remedial measures. Although the dose-response relationship between simple CWP and coal mine dust has been established (1), the causal agent(s) and the mechanism(s) involved in the progression of simple to complicated CWP are not yet defined. Many plausible hypotheses have been made to explain the mechanisms involved in the disease progression however none of them is satisfactory. In addition, the source of variation in occurrence of CWP among miners in different geographic areas (2), rank of coal seam (3,4), and job (5) remain unsolved."

Jan 1, 1988