Search Documents

By M. N. Plis

This report describes the initial results of long-range research on bit life conducted by the Bureau of Mines. Three commercial bit designs -a round-nose radial, 60° conical, and 90° conical with tungsten carbide (WC) inserts -and five experimental bits were tested. Four of the experimental bits were radial designs using polycrystalline diamond compact (PDC) inserts. The fifth was a 90° conical with an oversize WC insert. Bits were worn on a high-silica sandstone typical of coal mine roofs. The bits were mounted on a 34-in-diam drum section that provided a bit speed of 565 ft/min. Cutting forces were measured on a modified vertical slotter using a three-axis force dynamometer and recorded on an FM magnetic tape recorder. Changes in cutting forces, bit weight, and airborne dust due to gradual abrasive wear and catastrophic insert failure are presented. Tabulated and graphed data, photographs of the progression of bit wear, and selected qualitative visual and auditory observations of the bits taken throughout the experiment are found in the appendixes. The results show that bit life ranged from approximately 16,000 ft for the WC round-nose radial bit to over 125,000 ft for a PDC round-nose radial. Performance, in terms of bit life, cutting forces, wear rate, frictional sparking, machine vibration, and noise was in general best with the PDC bits, followed by the rotating WC bits, with the nonrotating WC bits (round-nose radial and locked 60° conical) being the worst. The results show variations in the included tip angles of new conical bits have an insignificant influence on bit performance when the effects are averaged over the life of the bit. In addition, new bits were generally found to entrain more primary respirable dust for a given cutting distance than worn-out bits. It is hypothesized that this is due to the difference in frictional behavior between new and worn bits. The results from these tests are being used in the Bureau's cutting system model (CSM).

Jan 1, 1988

By Thomas J. Peters

In 1978, the U.S. Bureau of Mines and the U.S. Geological Survey completed a joint mineral survey of the Chemise Mountain and King Range study areas as mandated by the Federal Land Policy and Management Act of 1916, Public Law 94-579. The U.S. Bureau of Mines examined all identified mineral prospects and deposits; the results of these examinations are included in this report. The U.S. Geological Survey studied the regional geology, geochemistry, and geophysics; the results of these studies are available in USGS Map MF-1196. No mineral resources were identified in either the Chemise Mountain or King Range study areas; however, a high-grade silver and base-metal occurrence, and minor manganese resources were identified in between the two study areas, within the King Range Conservation Area. The only mining activity in either area was a placer gold prospect on Honeydew creek in the northeastern part of the King Range study area. Three samples from this prospect contained no gold. The Chemise Mountain and King Range study areas are in a mountainous region along the coast of northern California, 230 road miles north of San Francisco, and 70 miles south of Eureka by way of U.S. Highway 101, through Garberville and Redway. The Chemise Mountain study area consists of 3,941 acres; it includes the 2,598-ft Chemise Mountain, and the cliff-lined seacoast southeast of Shelter Cove. a resort and fishing village. The King Range study area consists of 39.764 acres northwest of Shelter Cove, and includes the northwest-trending King Range with elevations above 4,000 ft. The Chemise and King Range study areas are underlain by deep-water marine sandstones, shales, and minor pillow basalts of the Late Cretaceous and early Tertiary Franciscan Subduction Complex. Mineral production was 1,650 tons of manganese ore within a manganiferous bed overlying pillow basalt at the Queen Peak mine southeast of the King Range study area. However, no significant manganese resources were found in the Queen Peak area. The Point Delgada area, directly south of the King Range study area, has prospects with high grade copper, lead. silver, and zinc. Exposures are inadequate to estimate resources; however, the metals may be associated with Franciscan volcanism (volcanogenic). The Chemise and King Range study areas may contain similar economic silver-rich, base-metal deposits.

Jan 1, 1992

Argentina follows Venezuela and Mexico as the largest producers of crude petroleum and natural gas in Latin America. Argentina 1S practically self-sufficient in fuels, but relies substantially on imports for its supply of copper, iron ore, ferroalloys, sulfur, and fertilizers. Mining activity is limited and is in an incipient stage of growth, considering the country's potential for mining. Most nonfuel mineral output in 1979 consisted primarily of minerals used for construction, while only 9% are other nonmetallic, and 2% are metallic minerals. Argentina is Latin America's major producer of boron minerals and uranium (yellow cake). Mineral exports consist primarily of borates, uranium concentrates, and of late, some tin. These exports have in the past been shipped mostly to Great Britain. London banks have been involved in arranging financing for St. Joe Minerals Corp. IS planned development of the El Pachon copper deposit (see map), and were being counted upon to also back the development of large copper and manganese projects. The following is a review of Argentine mineral production in 1979: (For 1981, the production of boron minerals is put at 167,000 metric tons and uranium at 300,000 metric tons.)

Jan 1, 1982

By John Ward Smith, Neil B. Young

Shale specific - gravity to oil - yield relationships were developed for black shales of the New Albany Formation of Kentucky from data collected on core samples representing the complete section of the formation in three counties . Linear equations for estimating oil yield from measured specific gravity and for estimating specific gravity from measured oil yield were shown to be applicable within small error limits to all the sites tested . Variation in pyrite content is the largest source of error .

Jan 1, 1964

By Robert M. Doerr

Isothermal oxidation kinetics were determined for three grades of Ni and for 99.99 percent Co in Ca and in air from 800° to 1,200° C. The oxidation reactions followed approximately the parabolic rate law. For 99.99 percent Ni in 02 at 1,200° C, the parabolic rate constant was 2 mg cm-2 hr-2. For 99.99 percent Co in dry air, the constant ranged from 1 mg cm-2 hr-2 at 800° C to 18 mg cm-2 hr-2 at 1,200° C; for 99.99 percent Co in 02 the constant was 2 mg cm -2 hr-2 at 800° C and 10 mg cm-2 hr-2 at 1,000° C. For 99 percent Ni in dry air, the constant ranged from 0.2 mg cm 2 hr-2 at 800° C to 3 mg cm 2 hr-2 at 1,200° C. By X-ray diffraction measurements, only divalent oxides were found in the scales. Volumetric and quartz-helix gravimetric methods were used. The volumetric apparatus was designed to permit less stringent restrictions on the corrosion specimens; it was also more convenient to use. The agreement between the weight gain determined gravimetrically and the 02 consumption determined volumetrically was not good enough for direct comparison of gravimetric and volumetric results.

Jan 1, 1963

By F. Garacia, J. Cervik

Gob holes are routinely used by the mining industry to vent methane from gobs and to prevent it from entering the mine ventilation system. In some cases, flows from gob holes are measured by centering an anemometer on the end of a discharge pipe. These measurements are erroneous and tend to be high by as much as 30 pct. The Bureau of Mines deter- mined method factors (correction factors) for anemometer measurements taken in this manner. Method factors for 4-, 6-, and 8-in (10.2-, 15.2-, and 20.3-cm) ID pipe are 0.68, 0.71, and 0.78, respectively. Comparisons between horizontal and vertical flows indicated no significant change in method factors. Consequently, the method factors for horizontal pipe flows can be applied to vertical upward flows.

Jan 1, 1987

By H. P. Greenwald

About mid-December 1936, the safety director of a large coal corporation visited the authors at the Bureau's Experimental coal mine to discuss a rock-dust barrier he had invented primarily for use in trackless entries of coal mines. The rock dust in this device was carried in its original paper containers and means were provided for ripping these open so that the dust might be scattered in the path of an explosion. The inventor termed the device a "bag barrier", and this term has been adopted in the present paper for convenience. At that time the device was in an early stage of development, and the inventor felt that the barrier should be tested to determine whether it had enough promise of being successful to justify further development. The matter was taken under consideration and finally three tests were made during the week of February 15, 1937. It was concluded that while the device did stop an explosion in two of the three tests, it was much loss effective than ordinary rock dusting, and that too few data were obtained to permit direct comparison with tests of other barriers. Apparently, the conditions under which the device could, be successful were somewhat limited, out the limits could not be defined without additional tests.

Jan 1, 1938

By C. M. McKinney

This report contains Bureau of Mines analyses of 291 samples of crude petroleum from the Gulf Coast Area of Louisiana and Texas. Included are 65 analyses from 51 Louisiana fields and 226 analyses from 216 Texas fields. Analyses from the Texas fields include 90 from 58 Upper Gulf Coast fields, 47 from 28 Middle Gulf Coast fields, and 89 from 40 Lower Gulf Coast fields. The analyses represent fields that produced 1,000 barrels or more per day during at least one of the years 19.57 through 1961, with the exception of 23 analyses from the Texas fields. The fields considered are listed by state and geographical groupings, with field names arranged alphabetically within each grouping. The tabulation also includes information concerning the geological sources of the samples. General characteristics of the crude oils and analytical and computed data determined from the analyses are summarized. Crude oil production data are given for the fields for 1960 and 1961 and are cumulative through 1961.

Jan 1, 1963

By B. W. Gandrud

In July 1948, the Bureau of Mines, United States Department of the Interior, in cooperation with the University of Alabama and mine operators, published Report of Investigations 4306, "A Combination Cleaning and Dewatering Process for Treating Fine 'Sizes of Coal, Preliminary Report In this report a new process, referred to as kerosene flotation; was described, and results of experimental work with the process Previous to the fall of 1947 were given, The contents of the report. were summarized on pages 19 and 20' as follows: In coal-preparation plants using wet methods of cleaning, the most difficult problem is the cleaning and dewatering of the "fines" from about 10-Mesh to 0. A combination proceed is now under investigation that shows promise of practically and feasibly solving this problem. The process is similar to froth flotation, but a generous quantity of kerosene is used as one of the reagents, and the feed is from approximately 10-mesh to 0 considerably coarser than the usual froth flotation feed. The kerosene and the coarseness of the reed result in a floated product that, under certain circumstances, can be dewatered satisfactorily by a simple process of mechanical squeezing, Squeezing is accomplished by means of an ordinary conveying' Auger-and trough assembly with a section of pipe easing at the outer end of the trough. The bottom of the trough and. casing is fitted with wedge-wire sections to permit escape of the water freed by the squeezing action of the auger. On account of the important role of the kerosene, the process has been referred to in this report as kerosene flotation. Up to now, the investigative work has been divided about evenly between the laboratory and commercial plants. Nearly all of the work has been done on sludges containing the solids from the underflow of dewatering screens. A few runs have been made on 10-mesh to 0: fines from raw coal, but in some of those runs the dewatering mechanism, failed to function.

Jan 1, 1950

By M. J. Ankeny

Coal-mine haulage ranks second as a cause of coal-mine fatalities, and the prevention of such accidents will materially improve progress in safety in the coal-mining industry. Beginning March 1950, Federal coal-mine inspectors were made responsible for completely investigating all fatal accidents in and around coal mines. During these 10 months, Federal coal-mine inspectors investigated 447 fatal accidents. This is a study of 121 of the fatal haulage accidents investigated, which constituted 27 percent of fatalities from all causes. Haulage employees represent only 12 to 15 percent of mine personnel, but, on the basis of accident frequency, their work is the most hazardous in coal mines. Fatal haulage accidents occurred in 53 bituminous coal-producing counties representing 14 States and Alaska. The physical conditions represent a cross section of' producing coal beds. Mining and transportation methods vary, from those of small hand-loading mines to those of modern mechanized mines.

Jan 1, 1951

By R. V. Higgins

A numerical method is presented to calculate the pressure distribution in a petroleum reservoir that has irregular boundaries. The computer program is straightforward and requires minimal data preparation. The method can also be used to determine pressure distribution in many other types of underground reservoirs. In this method, the grid solution of the fluid-flow equations in a reservoir that has regular boundaries (previously published) was expanded to handle irregular boundaries. The computer program locates grid points at the irregular boundaries. The method of mirror images is then used to form a special stencil to determine the pressure at each of these points. Two examples are presented to demonstrate the applicability of the method for virtually any reservoir configuration.

Jan 1, 1972

By J. C. Johnson

In situ stresses are important input data for the design of safe, stable stope layouts and extraction sequences. However, it is commonly assumed that normal and shear stress gradients in a stress field are negligible and, consequently, that stresses are uniform throughout the region of analysis. To evaluate these assumptions and to provide input data for an analysis of a shaft pillar mining plan, in situ stresses were measured at the Homestake Mine, Lead, SD, using overcoring on hollow inclusion cells and borehole deformation gauges. These measurements were used with conventional least squares, best fit data reduction schemes. The results showed that normal stresses within the shaft pillar were less than, but comparable to, those estimated from finite-element modeling. Shear stresses were an order of magnitude less than normal stresses and varied considerably from site to site. Possible causes of this variability include effects of scale, elastic moduli, anisotropy, and axial strain. Because of the variability, it is not possible to determine the magnitude of horizontal stress gradients.

Jan 1, 2010

By Earl L. Hastings

Although the principal market for diatomite in the United States is in the East,4 production of the material is presently restricted to the West, because the deposits are larger, mining costs are cheaper, and the quality of product is better than that obtained from other domestic deposits. However, Tallahatta diatomite, occurring in Choctaw and Clarke Counties, Ala., has a freight rate advantage, which should encourage competition for those market that are now being supplied with the purer diatomites from the western deposits. For this reason, diatomite occurrences in the Tallahatta formation were examined by the Bureau of Mines and physical properties of samples from the deposit were determined to obtain additional data for use by any potential producer who wished to evaluate the material for its commercial possibilities. In 1894 K. M. Cunningham5 found that the buhrstone formation (now known as the Tallahatta formation) contained "siliceous shells of marine diatoms, radiolaria and foraminifera, thus being rather of the nature of tripoli or diatomaceous earth than of a true clay." Cooke6 and Semmes7 also reported the Tallahatta formation to be composed principally of diatomaceous earth with accompanying beds of sand, clay, and sandstone.

Jan 1, 1963

By C. H. Riggs

This report presents pertinent data on all active water-flooding projects in Washington County, Okla., and describes in detail the operation and production history of five representative floods. The flooding of partly depleted oil-bearing sands to produce petroleum that would not be recovered by other methods is becoming increasingly important to the oil industry. In 1942, two water-flooding projects in Washington County produced 35 barrels of oil daily from 90 developed acres. In March 1951, 4,000 barrels of oil was being produced daily by the injection of 58,000 barrels of water on 19 active projects covering 1,645 acres. Several projects are being extended, and new operations are being initiated. Figure 1 shows the location of the active water-flooding projects in Washington County. The yearly oil production from Washington County increased from 1,076,000 barrels in 1948 to 1,720,000 barrels in 1950, owing principally to the effects of water flooding. To March 1951, permits to flood more than 8,000 acres in Washington County had been granted by the Oklahoma Corporation Commission.

Jan 1, 1951

By Henry P. Wheeler

Natural gas was first stored underground in Welland, County, Ontario Province, Canada, in 1915.3/ The following year natural gas in the United States was first stored underground successfully in the Zoar field near Buffalo, N, Y. Only three additional storage fields were in use in the United States in 1930, but by 1940 the number had increased to over 30, and since that time growth has been more rapid. At least 80 fields, with a combined storage capacity of 440,828 MM c. f ., were being utilized by 1949.4 / In May 1952, 142 storage projects having a capacity of 915,000 MM c.f. were in operation .5/ These fields are distributed from New York to California--from Michigan to Texas. In the Appalachian region alone, there are 101 storage fields with a combined capacity exceeding 526,000 MM cu. ft. Why Natural Gas is Stored Natural gas is stored in order to be readily available to meet the needs of consumers.

Jan 1, 1952

By Raja V. Rarnani, Robert L. Frantz

"The more than 75 research projects funded throughout the first 10 years of the Dust Center's operation have resulted in numerous cumulative findings fulfilling the goals of the Center. These project descriptions present the methodologies and project-to-project relationships leading to their various accomplishments and demonstrate the mesh between project objectives and Center goals.To develop equipment for collecting respirable dust samples.To develop experimental methods for particle-by-particle characterization of morphology, size, and chemistry.To develop experimental methods for overall respirable dust sample characterization of size distribution, chemistry, and crystallography.The project directly addresses the Center's goals to enhance the understanding of the scientific and engineering characteristics of fine and respirable mineral particles found in mining and milling atmospheres and to establish the relationship between natural and cultural factors (mine geology, mineralogy, mining and milling methods, equipment, and control measures) in the generation of fine particles. The project also aims to contribute to the development of control mechanisms for reducing ambient respirable dust concentrations and worker exposures.The work on this project is related to similar work on Coal Mine Dust Characterization (Project No. 2701/MN1) and Characterization of Dust Particles (Project No. 4203/PS3).Airborne dust sampling was performed at the following locations: 1) a sand and gravel quarry in Southern New Hampshire, 2) a welding facility, 3) a ceramic powder facility, 4) a metal powder facility, and 5) the air in Cambridge, Massachusetts. A portable sampling box incorporating two Sierra personal cascade impactors was designed and produced. At a 2-LPM flow rate, the effective cut-off diameters of the Sierra impactors were 10.0, 6.0, 3.5, 2.0, 0.9, and 0.5 mm, respectively, for each stage, and the air passed through a PVC filter after the last stage. In addition, the sampling box contained a total respirable dust filter. The substrates were weighed carefully before and after collection, and the weight increases were recorded. All films, foils, and filters were put in the balance chamber for more than 8 hours to stabilize the temperature and humidity before weighing. A Cash 21 microbalance (±0.001 mg) was used to weigh the Mylar films, SS films, and filters."

Jan 1, 1995

By W. L. Crentz

San Juan County, which occupies the extreme northwest corner of New Mexico, contains large reserves of coal in the Fruitland formation and in the Menefee formation of the Mesaverde group. The coals have bright luster, are brittle, and break easily in handling. All mines sampled are in the La Plata-Fruitland and Rio Chaco districts of the Durango-Gallup coal field. This large area, all within San Juan County, contains numerous coal beds 5 to 15 feet thick. Ellis2/ mentions the Carbonero (Fruitland in this report) bed in the La Plata-Fruitland district attaining a thickness of 36 feet. This bed has been correlated with the Carbonero bed, formerly mined at Carbon Junction, near Durango, Colo. During the field investigation covered by this report, no operating mine in the Fruitland bed was working a bed thickness of more than 15 feet.

Jan 1, 1957

By M. R. Peterson

The U.S. Bureau of Mines investigated column flotation for recovery of a high-grade fluorite (CaF2) concentrate and byproduct concentrates from the Fish Creek fluorite deposit in Eureka County, NY. The recovery scheme consisted of (1) grinding the ore to minus 48 mesh, (2) fluorite rougher and cleaner flotation, (3) desliming the rougher fluorite flotation tailings at 20 Jjm, (4) mica flotation, and (5) silicate rougher flotation. Acid-grade fluorspar, mica, free silica (Si02) sand, and low-grade beryl (Be3Al2S~018) concentrate were produced in a 100 lb/h continuous column flotation unit (CCFU). The highest results achieved were %.6-pct CaF2 recovery in a fIrst cleaner concentrate containing 99.7 pct CaF2. Beryl recovery was as high as 92 pct at a grade of 5.3 pct BeO. The silica sand, which assayed 98 pct Si02, was recovered as the rougher beryl flotation tailings. Collector reagent consumption was reduced 45 pct for fluorite and 58 pet for silicate flotation in comparison with bench-scale conventional flotation. All products were signillcantly improved in both grade and recovery over conventional flotation results, and the recovery scheme was simplifIed by removal of several stages of flotation in the fluorite and silicate flotation steps.

Jan 1, 1990

By Victor Kalcevic

A gas-flow retort for thermal processing of oil shale to recover shale oil was developed by the Bureau of Mines at its Oil-Shale Demonstration Plant, Rifle, Colo., from 1948 to 1952. The retort is a crossflow gas-to-broken-solids heat exchanger. The heating medium is the gas produced in the shale retorting process. The gas is heated in specially designed stoves outside the retort and recycled to the retort. Oil shale from the Mahogany ledge section of the Green River formation in northwestern Colorado was the material processed. Indicated maximum oil recoveries for 20-to 25-gallon-per-ton shale in a l2-inch-thick shale bed and a 20-inch bed are 96 and 91 weight-percent of Fischer assay, respectively. Heat requirements for maximum recovery are 600 to 750 B.t.u. per pound of shale. Properties of the recovered shale oil are affected slightly by shale-bed thickness and extent of retorting. Oil recovery from oil shales assaying over 30 gallons per ton is lower than that from leaner shales.

Jan 1, 1959

By Peter J. Clarke

Development of the mineral and energy resources of Afghanistan appeared to be a top priority of the Soviet-controlled Government in the country. In the Afghan Government's plan for 1980-81, the largest allocation in the development budget was for mines, industry, and energy (46.7%). In contrast, only 23.1% of the budget was allocated for agricultural development, despite the fact that the great majority of the population was dependent on farming. The mineral industry of Afghanistan consisted of the production of natural gas, cement, coal, fertilizer materials, and rock salt. Production levels for all of these commodities were down an average of 45% from those of 1978, before the Soviet invasion. Prior to the invasion, small quantities of asbestos, barite, and talc had been produced along with about 6,000 to 7,000 kilograms per year of lapis lazuli, a semiprecious gem stone. Afghanistan had supplied about 80% of the world's output of lapis lazuli. Following direct Soviet intervention, production of these minerals declined to near zero.

Jan 1, 1983